Wood drying process: impact on Scots pine lumber durability

There are indications that the drying process may have negative effects on the natural durability of wood. The impact of various drying processes on the durability of Scots pine lumber has been evaluated with mass loss in a decay test with brown rot fungus, Coniophora puteana, as measure of the decay resistance of sapwood and inner and outer heartwood. Drying with or without steam conditioning was performed in six different series: air drying, kiln drying at temperature ranges commonly used in Swedish sawmills at 70°C and 90°C with two different regulation principles, and one high-temperature drying at 110°C. Durability varied considerably both between and within boards. Sapwood showed considerable less durability than heartwood. No difference in durability was found between inner heartwood and outer heartwood. Air-dried heartwood showed the highest durability compared to other drying series. The lowest durability in sapwood and heartwood was found for series dried at the 90°C temperature level with high material temperature early in drying. The interpretation is that the duration of high material temperature at high moisture content (MC) is the critical combination for decay resistance in heartwood. Steam conditioning after drying decreased durability in sapwood.     

Effects of basic density,annual growth and drying schedule on selected quality factors of dried Siberian larch (Larix sibirica) timber

Abstract

Siberian larch (Larix sibirica Ledeb.) timber is suitable for many uses in the mechanical wood industry. Drying it without any decrease in value, however, is difficult and slow. The purpose of this research was to compare the drying quality of Siberian larch timber dried with three different conventional schedules taking into account the density and annual growth of wood. Five drying tests were performed. The final moisture content (MC), MC gradient, cracks, deformations (bow, crook, twist and cup) and case hardening were measured from the dried timber. The basic density particularly affected the MC, as shown in the differences regarding dried wood, with the denser wood having higher final MC and MC gradient. It was also found that large annual growth increased some deformations. Most of the measured factors were best after drying at the highest temperatures used; however, a slightly different trend was observed for bow, twist and cup. MC factors and twisting were the most problematic properties in drying according to this study. Sorting Siberian larch timber, particularly according to density, would improve the MC properties of dried timber by ensuring sufficient drying time, as economically as possible, for each timber piece.     

Microwave vacuum drying characteristics of Pinus massoniana wood

Microwave-vacuum (MV) drying characteristics of plantation Masson pine (Pinus massoniana) were studied experimen-tally for various levels of microwave radiation time, initial moisture content (MC), vacuum level and wood thickness. The results show that the process of MV drying for wood can be significantly divided into a short accelerating rate drying period, a long constant rate drying period and falling rate drying period, and the second drying period can extend to levels of mean MC below the fiber satu-r...     

Radial variations of wood properties of an endangered species, <Emphasis Type="Italic">Pinus armandii</Emphasis> var. <Emphasis Type="Italic">amamiana</Emphasis>

A dead tree of Pinus armandii Franch. var. amamiana (Koidz.) Hatusima (abbreviated to PAAm) was obtained from a natural habitat on Tanega-shima Island and various properties of its wood were investigated. Grain angle was measured and soft X-ray analysis was undertaken to obtain the density in each annual ring. Unit shrinkage and dynamic properties were measured by shrinkage, bending, and compression tests. Variations of wood properties in the radial direction, relationships of wood properties to density, and annual ring width were examined. Roughly speaking, variations in the radial direction of the grain angle, twist angle by drying, Young’s modulus and strength in static bending, absorbed energy in impact bending, compressive Young’s modulus, compressive strength, and compressive proportional limit corresponded to the variation of annual ring width. As a result, it was determined that if PAAm is afforested artificially for the purposes of lumber production and conservation, the annual rings of logs should not be too widely spaced. Wood properties of PAAm were similar to those of Japanese black pine (Pinus thunbergii Parl.), which is another representative pine on Tanegashima Island. This study was presented in part at the 56th Annual Meeting of the Japan Wood Research Society, Hiroshima, August 2007     

25年生马尾松生长和木材基本密度家系变异与选择

以福建省华安县西陂林场的25年生来自省内不同产地的46个马尾松自由授粉家系试验林为试材,研究了达主伐年龄时马尾松生长、干形和木材基本密度的家系差异以及性状间的相关性,并依据不同培育目标选择优良家系。结果表明,马尾松生长、树干圆满度和木材基本密度皆存在显著的家系差异,其中生长和树干通直度变异相对较大,而树干圆满度和木材基本密度变异较小,变异系数在10%以下。生长和干形性状受到弱至中度的家系遗传控制,家系遗传力为0.23 0.46;木材密度受到的遗传控制相对较强,家系遗传力为0.46。性状遗传相关分析结果显示,选择速生种源可同时改良树干圆满度,但对树干通直度和木材基本密度影响不大。根据不同用材对材质材性要求,选出24个纸浆纤维材优良家系和6个锯材优良家系,平均木材干物质量和胸径生长皆为对照的1.16倍。     

Models for Predicting Wood Properties in Stems of Picea abies and Pinus sylvestris in Sweden

To study and model the variation of wood properties, sample trees were selected from 42 Norway spruce and 20 Scots pine stands covering a wide variation in climatic and site conditions, stand maturation and tree sizes. Plot and tree measurements were followed by sampling wood from different heights in each sample tree and laboratory measurements of wood properties. Mixed linear and non-linear prediction models were developed using diameters, number of annual rings and climatic indices as explanatory variables. The variation in spruce properties explained by these variables was: basic density 50%, latewood content 52%, juvenile wood diameter 85%, heartwood diameter 94% and bark thickness 76%. The corresponding values for pine were 59, 54, 79, 92 and 85%. Random among-tree variance was an important contributor to the remaining variation for density and latewood. In general, only a minor part of the random variation was related to variance between stands. Predictions derived from the models for density and juvenile wood in both species, and heartwood in pine showed good agreement when validated with data sets from two other studies. The resulting models may be used for predicting wood properties in forest planning and in bucking computers in harvesters, provided that the essential information is available.     

Real-time wood moisture-content determination using dual-energy X-ray computed tomography scanning

ABSTRACT

The estimation of the pixel-wise distribution of the moisture content (MC) in wood using X-ray computed tomography (CT) requires two scans of the same wood specimen at different MCs, one of which is known. Image-processing algorithms are needed to compensate for the anisotropic distortion that wood undergoes as it dries. An alternative technique based on dual-energy CT (DECT) to determine MC in wood has been suggested by several authors. The purpose of the present study was to evaluate the hypothesis that DECT can be used for the determination of MC in real time. A method based on the use of the quotient between the linear attenuation coefficients (μ) at different acceleration voltages (the so-called quotient method) was used. A statistical model was created to estimate the MC in solid sapwood of Scots pine, Norway spruce and brittle willow. The results show a regression model with R²?>?0.97 that can predict the MC in these species with a RMSE of prediction of 0.07, 0.04 and 0.11 (MC in decimal format) respectively and at MC levels ranging from the green to the totally dry condition. Individual measurements of MC show an uncertainty of up to ±0.4. It is concluded that under the conditions prevailing in this study, and in studies referred to in this paper, it is not possible to measure MC with DECT.     

Outdoor exposure of untreated Scots pine (Pinus sylvestris L.) and Norway spruce [Picea abies (L.) Karst.] wood samples

Abstract

Untreated Scots pine (Pinus sylvestris) and Norway spruce (Picea abies) samples were exposed above ground in a durability test for 6 years. The samples consisted of three pieces of wood, 22×95×500 mm, screwed together; two pieces lengthwise with a third piece overlapping. Weight was measured, to calculate moisture content (MC), and samples checked regularly for cracks and fungal growth. Parameters investigated were heartwood/sapwood (pine), annual ring orientation (spruce), stand site, annual ring width and density. Stand site, annual ring width and density had no influence on MC or fungal growth for either pine or spruce. Spruce samples with vertical annual rings had fewer cracks than samples with horizontal annual rings. Pine sapwood samples had a high MC and a large amount of rot fungi, while heartwood had a lower MC and no rot. Most spruce samples were similar to pine heartwood, except from a few samples that had high MC and fungal growth. Those were all sawn from the outer part of the log. Therefore, it can be stated that spruce sawn from the inner part has almost the same properties as pine heartwood, while spruce from the outer part of the log has similar properties to pine sapwood.     

Volume growth and wood density of plus tree progenies of Pinus contorta in two Swedish field trials

Seventy‐four half‐sib families of lodgepole pine (Pinus contorta ssp. latifolia Engelm.) plus trees were measured for vigour, height growth, stem diameter, wood density and ring width in two Swedish field trials at age 9. Height growth, wood density and ring width differed between families within provenances with variance components of 3–8 %. Coefficients of variation were highest for height growth and lowest for ring width. Heritabilities were similar for height growth and wood density but lower for ring width. These genetic parameters seemed to be equal for all provenances. Indirect selection for high dry stem biomass was more effective using height growth than wood density, and a correlated response in wood density of 2.1 % of mean by selecting the 15 highest parent trees was indicated. Juvenile wood density looks uncertain as a selection criterion for mature wood density.     

Dose–response relationships between wood moisture content,wood temperature and fungal decay determined for 23 European field test sites

Scots pine sapwood (Pinus sylvestris L.) and Douglas fir heartwood (Pseudotsuga menziesii Franco) specimens were exposed in double layer field trials at 23 different European test sites under different exposure conditions (in total 27 test sets). The material climate in terms of wood moisture content (MC) and wood temperature was automatically monitored over a period of up to 7 years and compared with the progress of decay. The overall aim of this study was to establish dose–response relationships between climate factors and decay as a basis for the service life prediction of wood. The “Scheffer Climate Index” based on weather data collected at official meteorological stations at the different test sites poorly correlated with the corresponding decay progress and was therefore not a suitable tool for estimating site-specific decay potential. In contrast, the use of the combined material climatic parameters MC and wood temperature led to a feasible dose–response function and turned out to be a useful basis for service life prediction of wood.     

Modelling the distribution of wood properties along the stems of Scots pine (Pinus sylvestris L.) and Norway spruce (Picea abies (L.) Karst.) as affected by silvicultural management

In this work, empirical ring-based models were developed to predict the distribution of early wood percentage, wood density and fibre length along the stems of Scots pine (Pinus sylvestris L.) and Norway spruce (Picea abies (L.) Karst.) as affected by silvicultural management. The performance of the ring-based models was also compared for Scots pine and Norway spruce with corresponding disc-based (cross-sectional) models. Moreover, both models were integrated with example simulations by a process-based growth and yield model to analyze how management, such as thinning, affects the growth and wood properties of Scots pine trees over a rotation as an average for the tree stem, but also along the stem.The ring-based models built for annual early wood percentage (explained by ring width), air dry wood density (explained by early wood percentage and cambial age) and fibre length (explained by radial growth percentage and cambial age) predicted reasonably well the wood properties both at an intra-ring level, but also at a cross-sectional level. These predictions were also reasonably well in line with corresponding cross-sectional predictions by the disc-based models (which predicted the properties based on the number of annual rings and diameter at breast height and/or the cross-section being considered and temperature sum). The example simulations also demonstrated that both models predicted slightly lower wood density for dominant trees compared to dominated ones grown in thinned and unthinned Scots pine stands over a rotation. Unlike the disc-based model, the ring-based model predicted, on average, higher early wood percentage in dominant trees than in dominated ones. However, fibre length was not significantly affected when the averages of the whole stems were predicted, and this held true for both ring- and disc-based models.In summary, the incorporation of empirical ring-based wood property models into a process-based growth and yield model, offers a means to study in detail how environmental conditions, forest structure and management affect the quantity and properties of stem wood produced over a rotation. The disc-based wood property models used in this work are based on data with large geographical and genetic variation, and therefore may turn out to be more applicable for predicting future wood and fibre resources at a regional and national level. This kind of integrated use of wood property models with a process-based growth and yield model could help us to evaluate the forest resources under current and changing climate.     

Kiln drying behavior of lumber from ten fast-growth plantation species in Costa Rica

Abstract

Plantation wood from tropical climate has been introduced rapidly in the national market; however, there is lack of knowledge about the process. The main objective of this study was to investigate the kiln drying behavior of 10 plantation-grown wood species from natural forest in Costa Rica using the recommended drying schedule. Initial moisture content (MCi), final moisture content (MCf), drying rate, drying time, and drying defects were evaluated. The drying schedule applied produced the following results: (1) high MCi (over 110%) in four species and lower values in two species. (2) The largest drying time was found in species with high MCi, and the shortest drying time in species with lower MCi. (3) Significant variations of target MCf were found in some species, despite equalization and conditioning. (4) Exponential relationship MC=a*?^?t*b was used to establish a moisture content (MC) decrease model, which is not a good indicator of drying time for fives species. (5) High incidence of drying defects was found in Alnus acuminata and Vochysia guatemalensis. According to the above results, it is necessary to test other drying schedule oriented to improve lumber quality and to decrease variability of MC in wood from plantation trees.     

Methods for the determination of wood properties,Kraft pulp yield and wood fibre dimensions on small wood samples.

A trial set-up with methods for sampling, treatment and analysis of small wood chips are presented in this paper, to determine important wood and fibre properties, like basic density, dry density, volume swelling of wood, Kraft pulp yield, fibre length, fibre coarseness, fibre width, lumen width and fibre wall thickness. The required time for one sample is about 1.5 man-hour, but this requires relatively larger series and trained personnel. Acceptable measurement accuracy is achieved when the volume of the wood sample is at least 1.5 ml, except that of wood volume swelling. To gain acceptable measurement accuracy for volume swelling, the wood volume should be increased to at least 3 ml, and preferably more than 5–6 ml per sample. The level of pulp yield and wood density do not show a significant effect on the measurement accuracy for fibre cross-section dimensions. Fibre coarseness, on the other hand, has a significant influence on these accuracies. A double measurement of fibre coarseness will improve the accuracy to an acceptable level. The method presented here may, together with information about trees and growth locations, form the basis for greater insight into the mechanisms involved in development of wood and fibre properties in trees, which in turn may provide better control and utilisation of wood for pulp and paper production.Abbreviations CWD cell wall density in dry wood=1500 kg/m³ - Ww dry weight of wood (kg) - Vmax green (wet) volume of wood (m³) - Vmin dry volume of wood (m³) - BD basic wood density (kg/m³) - DD dry wood density (kg/m³) - VS maximum volume swelling of wood (%) - Wp dry weight of pulp (kg) - PY pulp yield (%) - C fibre coarseness, the average weight of a unit length of fibre (g/m) - CL average chip length (mm) - CWT average cell wall thickness (m) - FW average fibre width (m) - l average native fibre length in solid wood - L chip length - lc average fibre length in wood chip (mm) - Lc length-weighted fibre length in wood chip (mm) - lw native average fibre length in wood (mm) - Lw native length-weighted fibre length in wood (mm) - LW average lumen width (m) - llw average native fibre length, length weighted, in wood - X average fibre length in chip - Xlw average fibre length, length weighted, in chip     

Physical properties of two tropical wood species from Mozambique

Abstract

The aim of this study was to reveal some important physical properties of two lesser used wood species from Mozambique. Density of wood, green moisture content (MC), shrinkage, swelling, sorption–desorption behaviour and quantitative colour analyses were carried out to facilitate the potential use of Icuria dunensis (ncurri) and Pseudolachnostylis maprounaefolia (ntholo). The study found that the average densities at 12% MC were 907.1 kg m^?3 for ncurri and 1023.4 kg m^?3 for ntholo. The average values of green MC were 31.4% for ncurri and 39.2% for ntholo. Ncurri and ntholo wood showed low coefficients of anisotropy for heartwood, 1.3 and 1.4, respectively. The colour measurements described the patterns of radial and longitudinal variations in wood colour. In conclusion, ntholo and ncurri are characterized by high density and dimensional stability. Ntholo can be used where small dimensional changes are required, e.g. in joinery, flooring and furniture.     

马尾松木材材性特点及加工利用研究

马尾松是我国松属树种中地理分布最广的一种,也是南方的造林先锋树种和主要用材树种。文中从物理力学性能、纤维特性以及渗透性等方面论述了马尾松木材材性特点,介绍了马尾松木材干燥及脱脂处理技术、木材蓝变及其防治方法,总结了马尾松木材在实木利用、人造板生产等领域的应用现状,展望了马尾松木材加工利用的发展前景。     

Effect of steam pretreatment on wood moisture content and characteristics of vacuum drying

The effects of high temperature steam pretreatment on the change in wood moisture content (MC) and characteristics of vacuum drying were investigated in this study. Poplar and manchurian walnut woods were pretreated with high temperature steam at 100°C and 140°C, prior to vacuum drying. A comparison of the characteristics of vacuum drying between steam pretreated wood and untreated wood was carried out. The results show that during steam pretreatment, the MC of wood decreased within a few hours. The reduction of MC varied with the temperature; the higher the temperature, the faster the MC dropped. During the vacuum drying stage, the rates of drying of pretreated samples were higher than those of untreated samples when MC was below the fiber saturation point. Furthermore, the total drying time of samples treated at a steam temperature of 140°C was lower than that of untreated samples. Therefore, a vacuum procedure after steam pretreatment can effectively shorten the drying time when drying wood.     

Variation in treatability of Scots pine (Pinus sylvestris) by the chemical modification agent furfuryl alcohol dissolved in water

Scots pine (Pinus sylvestris) sapwood was investigated for variation in treatability using the wood modifying agent, furfuryl alcohol (FA) in water. The variation in treatability within trees, between trees and between different stands of Scots pine was studied. Investigated variables that reduced the residual variance significantly were: site location, latitude of site, height of trees, annual ring width, vertical and horizontal position in the tree and method of drying. Linear mixed model statistics were used and tree number was handled as a random variable. The best model reduced the treatability residual variance by 67%. Location was the single factor affecting treatability most. Differences in latitude between locations may be the reason for that. Latitude correlated negatively with the treatability. Within the trees, the treatability of sapwood increased with distance from ground and with distance from heartwood border. A small, but significantly better treatability was found for kiln dried wood (60°C) compared to air dried wood (20°C).     

Shear strength and perpendicular-to-grain tensile strength of defect-free Scots pine wood from mature stands in Finland and Sweden

Variations in parallel-to-grain static shear strength and perpendicular-to-grain tensile strength of Scots pine wood from mature stands in Finland and Sweden were studied by means of linear mixed model analyses. Approximately 35% of the total variation in shear strength could be described with readily available independent background variables; if the basic density was included, approximately two-thirds of the total variation could be controlled. In tensile strength perpendicular to grain, only approximately one-fourth of the total variation could be described with the respective background variables; the property was found to be independent on wood density, and the reasons for the absence of strength–density relationship are discussed.     

Influence of wood moisture content and wood temperature on fungal decay in the field: observations in different micro-climates

In this study, Scots pine sapwood (Pinus sylvestris L.) and Douglas fir heartwood (Pseudotsuga menziesii Franco) specimens were exposed in double layer field trials at four different exposure sites and under different exposure conditions (in total ten test sets). The material climate of wood in terms of wood moisture content (MC) and wood temperature was automatically monitored over a period of 6 years and compared with the progress of decay. The aim of this study was to highlight the interrelationship between microclimate, material climate, and decay as a basis for the establishment of dose-response functions to be used for service life prediction of wood and wood-based products. Differences in resulting decay dynamics between the test sites as well as between the different types of exposure were quantified and discussed with respect to corresponding microclimatic and material climatic conditions. The time between the beginning of exposure and the first occurrence of visible decay varied between the sites and influenced the total decay development. The fundamental importance of direct decay factors, such as MC and wood temperature, were underlined and basic requirements for establishing dose-response-functions to be used in service life prediction models were derived.