Mechanism for deformation of wood as a honeycomb structure I: Effect of anatomy on the initial deformation process during radial compression

The mechanism for radial compression of coniferous wood was examined from the viewpoint of the porous structure of wood. The compressive test was carried out in a wet-type scanning electron microscopy (WET-SEM) chamber to observe continuously the deformation process of wood. The initial stress-strain relation of the cellular solids or single cell was measured with image analyses of SEM photographs. The first fracture occurred in one tangential row of earlywood tracheids just after the load-displacement curve exceeded the proportional limit. The fracture occurred because of abrupt breaks of the radial cell walls. The first fractured cells had a tendency to have the smallest percentage of cell wall within an annual ring, and the cells suffered shearing deformation in a radial direction until the occurrence of the first fracture. On the basis of the results of image analyses, it was concluded that this shearing deformation of cells was almost linearly related to the compressive load.Part of this work was presented at the 47th annual meeting of the Japan Wood Research Society at Kochi, April 1997 and at the 1997 meeting of the Research Society of Rheology in the Japan Wood Research Society at Tsukuba, December 1997     

Piezoelectric behavior of wood under combined compression and vibration stresses II: Effect of the deformation of cross-sectional wall of tracheids on changes in piezoelectric voltage in linear-elastic region

This study investigated and clarified the relation between the piezoelectric voltage and microscopic fracture of hinoki (Chamaecyparis obtura Endl.), in particular the deformation of the cross-sectional wall of the tracheid in linear-elastic regions under combined compression and vibration stresses. The piezoelectric voltage-deformation (P-D) curve consisted of a linear region starting from the origin followed by a convex curved region. The linear region of theP-D curve was only about 60% of that of the load-displacement (L-D) curve. By applying combined stresses to a specimen, the cross-sectional walls of the tracheid were deformed mainly at the radial walls. When a tracheid was regarded approximately as a hexagonal prism, the elastic buckling stress of the radial wall was estimated from scanning electron microscope images and our method based on a modification of the Gibson and Ashby method. As a result, it was estimated that the elastic buckling stress was only about 80% of the stress at the proportional limit of theP-D curve. It is found that there are two consecutive regions before the proportional limit of theP-D curve: One is the region up to the spot where the radial cell wall generates the elastic buckling, and the other is the region starting from the end of the aforementioned region up to the proportional limit of theP-D curve.Part of this paper was presented at the 47th annual meeting of the Japan Wood Research Society, Kochi, April 3–5, 1997     

Arrangement of cortical microtubules in compression wood tracheids of Taxus cuspidata visualized by confocal laser microscopy

Cortical microtubules (MTs) in differentiating compression wood tracheids of Taxus cuspidata stems were visualized by confocal laser microscopy. They were oriented obliquely at an angle of about 45° to the tracheid axis during formation of the secondary wall. Artificial inclination altered the pattern of alignment of MTs. Banding MTs were helically oriented late during the formation of the secondary walls. These results indicate that MTs might control the orientation and localized deposition of cellulose microfibrils in the secondary walls of compression wood tracheids.Part of this report was presented at the 46th annual meeting of the Japan Wood Research Society, Kumamoto, April 1996     

Delignification of cell walls of <Emphasis Type="Italic">Chamaecyparis obtusa</Emphasis> during alkaline nitrobenzene oxidation

To clarify the behavior of whole lignins in wood cell walls during alkaline nitrobenzene oxidation, the delignification process from cell walls in normal and compression woods of Chamaecyparis obtusa Endl. (Cupressaceae) was observed using ultraviolet and transmission electron microscopies. The lignin content conspicuously decreased to around 10% after 35min in normal wood. The lignin content in compression wood finally leveled off at aroumd 10% after 50min. In gel filtration of oxidation products in ethyl acetate, a high molecular weight fraction was prominent in extracts from the early stage of the reaction. As the oxidation progressed, the high molecular weight fraction became less prominent in both normal and compression wood. Changes in the weights of cell wall residues during reaction indicated that approximately half of the components other than lignin were also removed from the cell walls. This shows that the majority of lignin with relatively high molecular weight is removed from the cell walls together with polysaccharides in the early stage of the reaction and that further oxidative degradation occurs in solution in later stages. Only a small amount of the lignin with low molecular weight could be analyzed by gas chromatography.Parts of this report were presented at the 47th (Kochi, April 1997) and 48th (Shizuoka, April 1998) Annual Meetings of the Japan Wood Research Society, and at the Lignin Symposium, Sapporo, October 1997     

Vibrational property changes of spruce wood by impregnation with water-soluble extractives of pernambuco (Guilandina echinata Spreng.)

Sitka spruce (Picea sitchensis Carr.) was treated with water-soluble extractive components of pernambuco (Guilandina echinata Spreng. syn Caesalpinia echinata Lam.) by two methods: impregnation under evacuation using an aspirator and repetitive surface application using a brush. The influence of these treatments on the vibrational properties were examined. The loss tangent (tan ) of the impregnated specimen decreased, up to nearly a half of its original value, with increasing weight gain. It is suggested that the decrease in tan results from impregnation of the extractive components into the amorphous region of cell walls, forming secondary bonds between matrix substances. The surface application of the extractive components, on the other hand, hardly brought about the desirable change in vibrational properties.Part of this work was presented at the 47th annual meeting of the Japan Wood Research Society, Kochi, April 1997, and the 48th annual meeting of the Japan Wood Research Society, Shizuoka, April 1998     

Determination of the distribution and reaction of polysaccharides in wood cell walls by the isotope tracer technique VIII: Selective radiolabeling of xylan in mature cell walls of magnolia (Magnolia kobus DC.) and visualization of its distribution by microautoradiography

To radiolabel xylan in mature cell walls selectively, magnolia (Magnolia kobus DC.) was administered withmyo-inositol-[2-³H] and allowed to metabolize for 1 month. The radiolabeled xylem tissue was then submitted to sulfuric acid hydrolysis and nitrobenzene oxidation. A large amount of radioactivity was found mainly in xylose, although slight activities were detected in glucose and in vanillin and syringaldehyde. The labeled tissue was submitted to a preparation of holocellulose followed by treatment with 24% potassium hydroxide (KOH). Radioactivity was distributed mainly in the KOH-soluble part of the holocellulose. These results indicate that most radioactivity was incorporated into xylan in the cell walls. The distribution of the incorporated radioactivity in the xylem tissue was visualized by microautoradiography. Radioactivities were distributed in the xylem more than 400 m from the cambium; and an inner layer of a secondary wall had formed at the labeled xylem. Consequently, selective radio-labeling of xylan was visualized in mature cell walls.Part of this report was presented at the 47th annual meeting of the Japan Wood Research Society, Kouchi, April 1997     

Lignan production inDaphne odora cell cultures

Lignan production in callus and cell suspension cultures ofDaphne odora is reported for the first time. The cell suspension culture produced pinoresinol, lariciresinol, secoisolariciresinol, matairesinol, and wikstromol. The production of matairesinol in the cell suspension culture was much higher than that inDaphne odora stem tissues.Part of this report was presented at the 51th annual meeting of the Japan Wood Research Society, Tokyo, April 2001     

Extractives ofJuniperus chinensis L. I: Isolation of podophyllotoxin and yatein from the leaves ofJ. chinensis

Two compounds, yatein and podophyllotoxin, were isolated from the chloroform-soluble fraction in the methanolic extractives of byakushin (Juniperus chinensis L.) leaves for the first time.This report was presented at the 47th annual meeting of the Japan Wood Research Society, Kochi, 1997     

Piezoelectric behavior of wood under combined compression and vibration stresses I: Relation between piezoelectric voltage and microscopic deformation of a Sitka spruce (Picea sitchensis Carr.)

This study investigated the relation between piezoelectric behavior and the deformation of trachieds in real time under combined compression and vibration stresses. Scanning electron microscope images were recorded directly into a video recorder. Two types of microscopic destruction were observed in the specimens. With the first type, although a small uprush around the boundary of the annual ring was observed, the specimens were broken only by shearing fracture in the 45° direction. With the second type, the specimens were finally broken by shearing fracture after repeated buckling. In these cases the piezoelectric voltage increased almost linearly in the elastic region, proceeded to the maximal point, and then decreased gradually. Finally a clear peak appeared in the buckling and shearing fracture. There is a curved relation between the specific gravity and the piezoelectric parameter when the influence of voids is considered, and there is a linear relation between the dynamic Young's modulus and the piezoelectric parameter when the stress is considered.Part of this paper was presented at the 46th annual meeting of the Japan Wood Research Society in Kumamoto, April 1996     

Cell wall thickness and tangential Young's modulus in coniferous early wood

To investigate the effect of wall thickening around cell corners on the tangential Young's modulus of coniferous early wood, tapered beam cell models in which the variation of the cell wall thickness in the axial direction was taken into account were constructed for seven species. Their tangential Young's moduli were compared with the experimental results. The calculated Young's moduli of tapered beam cell models were larger than those of the models composed of the cell walls with uniform thickness, although both models showed almost the same density. For some species the calculated Young's moduli of the models in which the cell wall thickness increased curvilinearly in the axial direction were much closer to the experimental values. The reduction of the radial cell wall deflection due to the increase of the stiffness around cell corners was considered to increase the tangential Young's modulus of a wood cell.This report was presented at the 49th annual meeting of the Japan Wood Research Society, Tokyo, April 1999     

Growth of cone-shaped carbon material inside the cell lumen by heat treatment of wood charcoal

Conclusions With treatment at 2500°C, wood cell walls partially transform into a turbostratic carbon structure, which has an X-ray diffraction peak corresponding to a layer plane spacing of 0.343 nm. Despite this change, there was no apparent change within the cell wall seen by SEM.Cone-shaped carbon material was formed inside the cell lumen after treatment at 2500°C. This is not a feature originating from any wood cell organism and seems to result from vaporized carbon or pyrolysis gases that originate within the cell wall.Part of this work was presented at the 52nd Annual Meeting of the Japan Wood Research Society, Gifu, April 2002     

Thermal constants of wood during the heating process measured with the laser flash method

The thermal diffusivity, specific heat, and thermal conductivity of 13 species of wood were measured by means of the laser flash method to investigate the thermal properties of wood during the heating process. The temperature ranged from room temperature to 270°C in air or under vacuum. The thermal diffusivity varied little during the heating process up to 240°C. The values in air were larger than those under vacuum. There was a linear relation between the specific heat and the ambient temperature, and the specific heat under vacuum was larger than that in air at high temperature. The thermal conductivity increased with density and the ambient temperature. To discuss the effects of the atmospheric conditions on the thermal constants of wood, a theoretical model of thermal conductivity was proposed and its validity examined, where the wood was assumed to be a uniformly distributed material composed of cell walls and air.Part of this paper was presented at the 47th annual meeting of Japan Wood Research Society at Kochi, April 1997     

Acoustoelastic effect of wood II: Effect of compressive stress on the velocity of ultrasonic longitudinal waves parallel to the transverse direction of the wood

The changes in the velocity of ultrasonic waves propagating in wood parallel to the direction of applied stress are discussed. The ultrasonic mode was longitudinal waves traveling along the direction of applied stress with the compressive load applied parallel to the transverse direction of the wood. The ultrasonic velocities were measured by the sing-around method. The experimental results indicated the existence of an acoustoelastic phenomenon in the transverse direction of the wood. The percent change in the ultrasonic velocity was given as a function of the applied stress. The change in the velocity depended on the species and structural direction of the wood. That is, in the radial direction of hardwood, the ultrasonic velocity increased with increases in compressive stress at the initial stress level of less than 2MPa; it then gradually decreased with increases in stress. A change in velocity from an increase to a decrease was considered a unique phenomenon for wood. In contrast, in the radial direction of softwood and the tangential direction of hardwood, the ultrasonic velocity decreased with increases in stress from the beginning of loading. This phenomenon is also generally observed in metallic materials. The relations between velocity and stress at the initial stress level and between velocity and strain in the range of large deformation are represented by essentially straight lines. The acoustoelastic constants of wood were obtained from these relations at the initial stress level. The absolute values of the constants in the transverse direction of wood were larger than those for metals and were larger than those for the longitudinal direction of wood reported in our previous paper.This research was presented at the 1st Meeting of the Research Society of the Acoustoelastic Measurements in the Japan Society of Non-Destructive Inspection at Osaka, October 1996 and at the 47th Annual Meeting of Japan Wood Research Society at Kochi, April 1997     

Analysis of phenol-resorcinol-formaldehyde resins

A method based on high-performance liquid chromatography (HPLC) and proton magnetic resonance (PMR) spectroscopy for analyzing phenol-resorcinolformaldehyde (PRF) resins is reported. The equations that describe the number-averaged structures of PRF resins in terms of the PMR absorption intensities of acetylated resins have been derived on the basis of the work of Woodbrey et al. and Anderson et al. The P/R molar ratio of the resin calculated from the PMR intensities was in good agreement with the synthetic P/R molar ratio when correction was made for the loss of phenol evaporated during the drying process that preceded the acetylation. The number-averaged molecular weight (M_n) of the acetylated resin calculated from the PMR intensities agreed with the M_n determined by cryoscopy. Unreacted phenol and resorcinol could be determined by analyzing the water-soluble fraction of the resin by use of high-performance liquid chromatography.Part of this paper was presented at the 4th annual meeting of the Kyushu branch of the Japan Wood Research Society, Miyazaki, November 1997, and at the 48th annual meeting of the Japan Wood Research Society, Shizuoka, April 1998     

Effect of growth on wood properties for Japanese larch (Larix kaempferi): Differences of annual ring structure between corewood and outerwood

To investigate the relations between growth and the wood properties of Japanese larch (Larix kaempferi), six sample trees of varied ages and radial growth were felled and the ring width, ring density, percentage of latewood, and some other factors were determined. There were significant differences in ring density and percentage of latewood between sample trees with vigorous growth and those with poor growth. In corewood the ring density decreased with increasing ring width for all sample trees, whereas in outerwood this trend did not appear. Moreover, the latewood width increased with the increment of ring width only in outerwood, whereas there was almost no change in the corewood. The variation in patterns of ring width, ring density, and percentage of latewood in the radial direction and the relation with height was also studied.Part of this report was presented at the 47th annual meeting of the Japan Wood Research Society, Kochi, April 1997     

Drying and anatomical characteristics of sugi wood attacked by bacteria during pond storage

Seven species of bacteria were isolated and identified from ponded sugi (Cryptomeria japonica D. Don) logs, and six species showed potent wood-degrading activities. To evaluate the effects of these isolated bacteria on the drying and anatomical characteristics of wood, small fresh blocks of sugi were immersed in water suspensions containing bacteria for 1–7 months. The permeability and drying properties were evidently improved. Most of the encrusting substances adhering to the cell lumens and the pit chambers were removed, and the pit membranes were destroyed. These anatomical changes due to bacterial activity were assumed to improve the permeability of sugi wood.Part of this report was presented at the 40^th annual meeting of the Japan Wood Research Society, Tsukuba, April 1990; the 41^st annual meeting of the Japan Wood Research Society, Matsue, April 1991; and the IUFRO XX World Congress, Tampere, August 1995     

Strain-softening behavior of wood under tension perpendicular to the grain

Three softwood samples and one hardwood sample were tested under a tension load applied along the radial direction using small clear specimens and the local tension strain was measured using the digital image correlation method. We successfully obtained a stress-strain curve with a strain-softening branch by calculating the stress using the strain distributions in the vicinity where the specimen ruptured. The continuous digital imaging of the specimen proved to be very effective for measuring the strain in quasi-brittle materials such as wood under tension. The nonlinearity of the stress-strain curve was quantified using two parameters representing the deviation from linear elasticity, and the formula of the stress-strain curve was deduced from the interrelation between these parameters. This formula is expressed quite simply by using the modulus of elasticity along the radial direction and another constant that is unique to the material. Part of this article was presented at the 56th Annual Meeting of the Japan Wood Research Society, Akita, Japan, August 2006     

Morphological changes in the cytoskeleton, nuclei, and vacuoles during cell death of short-lived ray tracheids in the conifer Pinus densiflora

Morphological changes in the cytoskeleton, nuclei, and vacuoles were monitored during the cell death of short-lived ray tracheids in the conifer Pinus densiflora. After formation of the dentate thickenings that occurred at the final stage of formation of cell walls, organelles started to disappear in differentiating ray tracheids. First, the microtubules and vacuoles disappeared. Then actin filaments disappeared in the differentiating ray tracheids adjacent to ray tracheids that lacked nuclei, and, finally, the nuclei disappeared. These features indicate that cell death in ray tracheids might differ from the programmed cell death of tracheary elements that has been studied in vitro in the Zinnia culture system. This study was presented at the 57th Annual Meeting of the Japan Wood Research Society, August 8–10, 2007, Hiroshima, Japan     

Chemical structural elucidation of total lignins in woods I: fractionation of the lignin in residual wood meal after extraction of milled wood lignin

Residual wood meal after extraction of milled wood lignin (WMEM) ofEucalyptus globulus was extracted with alkali and LiCl/N,N-Dimethylacetamide (DMAc). These agents dissolve mainly hemicellulose and cellulose, respectively. The extractability of WMEM in alkali solutions was influenced by the degree of swelling of the cellulose. Under good swelling conditions, considerable amounts of cellulose and lignin were extracted with the hemicellulose. Maximum extractability was about 60% of the WMEM under optimum conditions (3 M or 5 M LiOH or 3M NaOH solution). Some portion of cellulose was extracted with LiCl/DMAc at room temperature. Thus, lignin inE. globulus WMEM was divided into three fractions: hemicellulose-lignin fraction, cellulose-lignin fraction, and insoluble-lignin fraction.Part of this work was presented at the 49th annual meeting of the Japan Wood Research Society, Tokyo, April 1999; and at the 50th annual meeting of the Japan Wood Research Society, Kyoto, April 2000     

Vibrational property changes of spruce wood by impregnation with watersoluble extractives of pernambuco (Guilandina echinata Spreng.) II: structural analysis of extractive components

Heartwood of pernambuco (Guilandina echinata Spreng, synCaesalpinia echinata Lam.), which has been used as material for violin bows, was extracted by soaking in water, and the obtained extractives were analyzed. The main components of the extractives were identified to be protosappanin B and brazilin. In particular, protosappanin B occupied about 40% of the pernambuco extractives. The loss tangent (tan) of spruce wood impregnated with protosappanin B decreased markedly, the same as that of specimens impregnated with extractives before being purified. It is expected that protosappanin B can make a contribution to the decrease in tan due to impregnation with extractives.Part of this work was presented at the 48th annual meeting of the Japan Wood Research Society, Shizuoka, April 1998; and the 49th annual meeting of the Japan Wood Research Society, Tokyo, April 1999