Properties and Structures of Flours and Starches from Whole,Broken, and Yellowed Rice Kernels in a Model Study

The objective of this study was to compare the structure and properties of flours and starches from whole, broken, and yellowed rice kernels that were broken or discolored in the laboratory. Physicochemical properties including pasting, gelling, thermal properties, and X‐ray diffraction patterns were determined. Structure was elucidated using high‐performance size‐exclusion chromatography (HPSEC) and high‐performance anion‐exchange chromatography with pulsed amperometric detection (HPAEC‐PAD). The yellowed rice kernels contained a slightly higher protein content and produced a significantly lower starch yield than did the whole or broken rice kernels. Flour from the yellowed rice kernels had a significantly higher pasting temperature, higher Brabender viscosities, increased damaged starch content, reduced amylose content, and increased gelatinization temperature and enthalpy compared with flours from the whole or the broken rice kernels. However, all starches showed similar pasting, gelling, thermal properties, and X‐ray diffraction patterns, and no structural differences could be detected among different starches by HPSEC and HPAEC‐PAD. α‐Amylase may be responsible for the decreased amylopectin fraction, decreased apparent amylose content, and increased amounts of low molecular weight saccharides in the yellowed rice flour. The increased amount of reducing sugars from starch hydrolysis promoted the interaction between starch and protein. The alkaline‐soluble fraction during starch isolation is presumed to contribute to the difference in pasting, gelling, and thermal properties among whole, broken, and yellowed rice flours.     

Heat Treatments of Milled Rice and Properties of the Flours

The effects of autoclave and oven treatments on the gelatinization of rice flour and on the rheological characteristics of its pastes were studied by differential scanning calorimetry (DSC), rapid viscoanalysis (RVA), and rotational viscometry. Flours from autoclave‐treated rice (ATR) and oven‐treated rice (OTR) were prepared, respectively, by heating at 120°C for 60 min and 160°C for 60 min followed by drying (ATR sample), and grinding at 2.2–12.9% moisture content. The rice flour dispersions were adjusted between pH 6.3 and 2.8 using 0.2M citrate buffer. The retort processing of rice flour in water pastes were done at 120°C for 20 min either once or twice. The gelatinization peak temperature (PT and T_o) and the peak temperature corresponding to the amylose‐lipid complexes (T_p3) of ATR increased at pH 6.3 and 2.8 compared with OTR and UTR flour. This indicates that the internal structures of the starch granules in ATR became more stable to heat and acid, even though the damaged starch content of ATR was 23% compared with 16 and 7%, respectively, for untreated rice flour (UTR) and OTR. The OTR flour pastes showed a gel‐like behavior at pH 4.5 after retort processing in water at 120°C for 20 min; however, the ATR mixture behaved more like a liquid paste. Decreases in the reducing sugar content of OTR and ATR pastes suggested that enzymes in the heat‐treated rice were denatured, which retarded the hydrolysis of glucose chains and the rupture of starch granules during pasting.     

Effect of Ultrasonic Treatment of Brown Rice at Different Temperatures on Cooking Properties and Quality

This research studied developing quick cooking brown rice by investigating the effect of ultrasonic treatment at different temperatures on cooking time and quality. The medium grain brown rice was ultrasonically treated in water at temperatures of 25, 40, and 55°C for 30 min and then dried by air at 25°C to its initial moisture content (11.0 ± 0.6%, wb) before cooking. The microstructure of rice kernel surface, chemical composition, and optimal cooking time of treated brown rice were determined. The pasting and thermal properties and chemical structure of flour and starch from treated brown rice were also examined. The results showed that the optimal cooking times were 37, 35, and 33 min after treatment at 25, 40, and 55°C, respectively, compared to the control of 39.6 min. The ultrasonic treatment resulted in a loss in natural morphology of rice bran, allowing water to be absorbed by a rice kernel easily, particularly at high‐temperature treatment. Even through rice flour still maintained an A‐pattern in the pasting properties, the crystallinity significantly increased after treatment at 55°C. Ultrasonic treatment increased the peak, hold, and final viscosities and decreased the onset temperature (T_o) and peak temperature (T_p), significantly. Thus, ultrasonic treatment could be used for reducing cooking time of brown rice.     

Fine Structures of Starches from Long‐Grain Rice Cultivars with Different Functionality

The structural features of rice starch that may contribute to differences in the functionality of three long‐grain rice cultivars were studied. Dried rough rice samples of cultivars Cypress, Drew, and Wells were analyzed for milling quality, grain physical attributes, and starch structures and physicochemical properties. Drew was lower in head rice yield and translucency and higher in percentage of chalky grains compared with Cypress and Wells. Apparent amylose content (21.3–23.1%), crude protein (8.3–8.6%), and crude fat (0.48–0.64%) of milled rice flours were comparable, but pasting properties of rice flours as measured by viscoamylography, as well as starch iodine affinity and thermal properties determined by differential scanning calorimetry were different for the three cultivars. Drew had higher peak, hot paste, and breakdown viscosities, and gelatinization temperature and enthalpy. Molecular size distribution of starch fractions determined by high‐performance size‐exclusion chromatography showed that the three samples were similar in amylose content (AM) (20.0–21.8%) but differed in amylopectin (AP) (64.7–68.3%) and intermediate material (IM) (10.9–13.5%). Drew had highest AP and lowest IM contents, whereas Cypress had the lowest AP and highest IM contents. High‐performance anion‐exchange chromatography of isoamylase‐debranched starch indicated that the AP of Drew was lower in A and B1 chains but higher in B2, B3, and longer chains.     

Malted Sorghum as a Functional Ingredient in Composite Bread

To alleviate the adverse effects (grittiness and high crumb firmness) caused by the inclusion of sorghum flour in composite breads, sorghum grain was malted with the aim of decreasing the gelatinization temperature and increasing the water‐holding capacity of sorghum flour. Four different heat treatments were investigated: drying the malt at high temperatures (50–150°C), stewing, steaming, and boiling before drying the malt at 80°C. Malting decreased the pasting temperature of sorghum to values approaching those of wheat flour, but the paste viscosity was very low. Increasing the malt drying temperature inactivated the amylases but gave malts of darker color and bitter taste. Stewing, steaming, and boiling the malt before drying almost completely inactivated the amylases and increased the enzyme‐susceptible starch content and the paste viscosity of malt flours. Bread made with boiled malt flour (30%) had an improved crumb structure, crumb softness, water‐holding capacity, and resistance to staling, as well as a fine malt flavor compared with the bread made with grain sorghum flour (30%). Consumers preferred the malted sorghum bread over the bread made with plain sorghum flour.     

Application of High‐Intensity Ultrasound and Surfactants in Rice Starch Isolation

High‐intensity ultrasound was evaluated as an alternative method to isolate rice starch without the use of chemicals as in the traditional alkaline steeping method. Surfactants, including sodium dodecyl sulfate (SDS), sodium stearoyl lactylate (SSL), and Tween 80, at 0.1, 0.3, or 0.5% combined with high‐intensity ultrasound were also investigated for rice starch isolation. A rice flour slurry (33%) was subjected to sonication for 15, 30, or 60 min at an amplitude of 25, 50, or 75% and at 40 or 50°C. The starch yield was not significantly affected by the treatment temperature and ranged from 46.7 to 76.2% (starch dry basis) after the sonication treatment; the protein and damaged starch contents of the isolated starches were 0.9–1.7% and 3.1–3.5% (dry basis), respectively. The combination of 0.5% SDS and high‐intensity ultrasound improved the starch yield to 84.9% with low residual protein, however, little improvement was observed with SSL or Tween 80. The pasting properties of isolated starch as measured by a Rapid Visco‐Analyser were affected by the treatment temperature and by the amount of residual protein and damaged starch. The thermal properties of the isolated starch were not changed by sonication and the amylose content remained unchanged. The surface of the isolated starch was not damaged by sonication as shown by scanning electron microscopy. High‐intensity ultrasound, alone or combined with SDS, showed a great potential for rice starch isolation in a short period of time without generating alkaline effluent.     

Fermented Sorghum as a Functional Ingredient in Composite Breads

Whole sorghum flour was fermented (a five‐day natural lactic acid fermentation) and dried under forced draught at 60°C, and evaluated for its effect on sorghum and wheat composite bread quality. In comparison with unfermented sorghum flour, fermentation decreased the flour pH from 6.2 to 3.4, decreased total starch and water‐soluble proteins, and increased enzyme‐susceptible starch, total protein, and the in vitro protein digestibility (IVPD). Fermentation and drying did not decrease the pasting temperature of sorghum flour, but slightly increased its peak and final viscosity. In comparison with composite bread dough containing unfermented sorghum flour, fermented and dried sorghum flour decreased the pH of the dough from 5.8 to 4.9, increased bread volume by ≈4%, improved crumb structure, and slightly decreased crumb firmness. IVPD of the composite bread was also improved. Mixing wet fermented sorghum flour directly with wheat flour (sourdough‐type process) further increased loaf volume and weight and reduced crumb firmness, and simplified the breadmaking process. It appears that the low pH of fermented sorghum flour inactivated amylases and increased the viscosity of sorghum flour, thus improving the gas‐holding capacity of sorghum and wheat composite dough. Fermentation of sorghum flour, particularly in a sourdough breadmaking process, appears to have considerable potential for increasing sorghum utilization in bread.     

Physicochemical Properties of Rice Dried in a Single Pass Using High Temperatures

This study evaluated the physicochemical properties of high‐temperature, single‐pass dried rough rice. Pureline cultivars Wells (long grain) and Jupiter (medium grain) and hybrid cultivar CL XL729 (long grain), at initial moisture contents of 17.9–18.1% were dried in a single pass to approximately 12.5% moisture content with drying air temperatures of 60, 70, and 80°C and relative humidities of 13–83%. Immediately after drying, the samples were tempered for 1 h at the drying air temperatures in sealed plastic bags. Color, degree of milling, pasting viscosity, and thermal properties of the milled rice were evaluated. Results showed that color, degree of milling, and thermal properties were not affected by drying treatments. However, peak and final viscosities increased with increasing drying air temperatures in all three cultivars.     

Effects of Cultivar and Processing Condition on Physicochemical Properties and Starch Fractions in Parboiled Rice

Starch can be classified into rapidly digestible starch (RDS), slowly digestible starch (SDS), and resistant starch (RS) according to its resistance to amylolytic enzymes. This study investigated the effects of cultivar and feedstock under varying parboiling conditions on the physicochemical properties and starch fractions of parboiled rice. Rice (rough or brown) was soaked, steamed under pressure, dried immediately or stored at room temperature for 24 hr prior to drying, and then treated with or without a repeated steam cycle prior to milling. The storage treatment significantly increased the retrograded amylopectin enthalpy and amylose‐lipid complex melting temperature of parboiled rice. Parboiled rice samples prepared from brown rice feedstock had higher peak melting temperatures but lower enthalpy values of retrograded amylopectin than samples prepared from rough rice after the storage treatment. The pasting viscosity of parboiled rice was most affected by the repeated autoclaving treatment and cultivar. Starch fractions in parboiled rice were significantly affected by cultivar and storage and by the interactions of cultivar and parboiling conditions. The storage treatment significantly increased SDS and generally decreased RDS in parboiled rice. Parboiled rice with different SDS and RS contents can be produced by varying rice cultivar and parboiling conditions.     

Effect of Extrusion Conditions on Pasting Behavior and Microstructure of Refabricated Rice: A Response Surface Analysis

The effects of moisture, screw speed, and barrel temperature on pasting behavior of refabricated rice grains were investigated in a corotating twin‐screw extruder with response surface methodology. The rice flour obtained from broken rice (≤1/8 of actual kernel size) of PR‐116 variety was used in the study. The screw speed was set at five levels between 49 and 150 rpm, barrel temperature between 59 and 110°C, and feed moisture between 31 and 45%. All pasting properties of refabricated grains evaluated—peak viscosity, hold viscosity, breakdown viscosity, final viscosity, and setback viscosity—were significantly (P < 0.01) affected by the three process variables. Barrel temperature was the most significant variable, with quadratic effect on all viscosity parameters. Response surface regression models were established to correlate the viscosity profile of refabricated rice grains to the process variables. The optimum moisture content, screw speed, and barrel temperature estimated by a response surface of desirability function for the production of refabricated rice were 36%, 130 rpm, and 89.5°C, respectively. Scanning electron microscopy also revealed that intermediate moisture and temperature along with high screw speed during extrusion could create a more realistic appearance of refabricated rice with less rupture of starch granules.     

A Better Understanding of Factors That Affect the Hardness and Stickiness of Long‐Grain Rice

Eight U.S. long‐grain rice cultivars were studied for chemical compositions, physicochemical properties, and leaching characteristics in relation to hardness and stickiness of rice flour paste and cooked rice. There were differences in the chemical composition of rice kernels among the eight rice cultivars, including crude protein (6.6–9.3%), crude fat (0.18–0.51%), and apparent amylose content by iodine colorimetry (19.6–27.0%). Differences were also observed in gelatinization temperatures and enthalpies, pasting temperatures and viscosities, leached/insoluble amylose, soluble solids, and hardness and stickiness of rice flour pastes and cooked rice kernels. The quantity and molecular size distribution of the leached starch molecules varied greatly among the samples. Protein and crude lipid contents negatively correlated with hardness of rice flour paste and cooked rice, but positively correlated with stickiness. Apparent amylose content correlated with gel properties but not cooked rice texture, whereas the ratio of A and short B chains to long B chains of amylopectin correlated significantly with cooked rice texture.     

Effect of Processing on Functional Properties of Wheat Gluten Prepared by Cold‐Ethanol Displacement of Starch

Functional properties of gluten prepared from wheat flour are altered by separation and drying. Gluten was separated and concentrated by batterlike laboratory methods: development with water, dispersion of the batter with the displacing fluid, and screening to collect the gluten. Two displacing fluids were applied, water or cold ethanol (70% vol or greater, ‐13°C). Both the water‐displaced gluten (W‐gluten) and ethanol‐displaced‐ gluten (CE‐gluten) were freeze‐dried at ‐20°C as a reference. Samples were dried at temperatures up to 100°C using a laboratory, fluidized‐bed drier. Tests of functionality included 1) mixing in a mixograph, 2) mixing in a farinograph, and 3) the baked gluten ball test. Dough‐mixing functionality was assessed for Moro flour (9.2% protein) that was fortified up to 16% total protein with dried gluten. In the mixograph, CE‐gluten (70°C) produced improved dough performance but W‐gluten (70°C) degraded dough performance in proportion to the amount added in fortification. In the microfarinograph, there was a desirable and protein‐proportional increase in stability time for CE‐gluten (70°C) but no effect on stability for W‐gluten (70°C). Baking was evaluated using the baked gluten ball test and the percentage increase in the baked ball volume relative to the unbaked gluten volume (PIBV). PIBV values were as high as 1,310% for freeze‐dried CE‐gluten and as low as 620% for W‐gluten dried at 70°C. PIBV for CE‐gluten was reduced to 77% of the freeze‐dried control by fluid‐bed drying at 70°C. Exposure of CE‐gluten to 100°C air gave a PIBV that was 59% of the reference, but this expansion was still greater than that of W‐gluten dried at 70°C. The highest values of PIBV occurred at the same mixing times as the peak mixograph resistance.     

Effects of Postharvest Elevated‐Temperature Exposure on Rice Quality and Functionality

Rapid drying with high‐temperature air has gained interest in the rice industry, but the effects of elevated‐temperature exposure on physicochemical properties of rice are of concern. This study investigated the effects of exposing rough rice to elevated temperatures for various durations without removing moisture. Physicochemical property response was evaluated in terms of head rice yield (HRY), germination rate (GR), milled‐rice yellowing, pasting properties, and gelatinization temperatures. Two long‐grain cultivars (pure‐line Wells and hybrid CL XL729) at initial moisture contents (IMCs) of 17.9 and 18.6%, respectively, and dried moisture content (DMC) of 12.5%, were hermetically sealed and exposed to 40, 60, and 80°C for various durations. Exposure to 80°C of IMC samples of Wells and CL XL729 resulted in a significant (2.3–2.5 percentage point) reduction in the HRYs. A 2 hr exposure of both cultivars at IMC level to 60°C completely inhibited GR, and exposure to 80°C of the cultivars at both moisture content (MC) levels immediately inhibited GR. Exposure to 80°C for almost all durations and 60°C for durations over 4 hr produced significant yellowing in both cultivars at IMC. Significant yellowing in both cultivars at DMC was also observed during a 28 day storage following 80°C exposure. In general, peak viscosities of both cultivars at IMC increased only after extended exposure to 40 and 60°C, but peak viscosities of the cultivars exposed to 80°C increased sharply and immediately upon exposure. No significant differences were observed in gelatinization temperatures of either cultivar at either MC level from elevated‐temperature exposure. Results from this study suggest that extreme‐temperature exposure of rough rice affects HRY, GRs, yellowing, and pasting properties of rice, but the extent of impact is MC dependent.     

Extrusion of Cross‐Linked Hydroxypropylated Corn Starches II. Morphological and Molecular Characterization

A series of cross‐linked hydroxypropylated corn starches were extruded with a Leistritz micro‐18 co‐rotating extruder. Extrusion process variables including moisture (30, 35, and 40%), barrel temperature (60, 80, and 100°C), and screw design (low, medium, and high shear) were investigated. Scanning electron microscopy (SEM) of extruded starches showed a gel phase with distorted granules and granule fragments after extrusion at 60°C. After extrusion at 100°C only a gel phase was observed with no granular structures remaining. High performance size exclusion chromatography (HPSEC) equipped with multiangle laser light‐scattering (MALLS) and refractive index (RI) detectors showed extruded starches degraded to different extents, depending on extrusion conditions. The average molecular weight of the amylopectin of unextruded native corn starch was 7.7 × 10⁸. Extrusion at 30% moisture, 100°C, and high shear reduced the molecular weight of amylopectin to 1.0 × 10⁸. Hydroxypropylated normal corn starch extruded at identical conditions showed greater decreases in amylopectin molecular weight. With the addition of cross‐linking, the amylopectin fractions of the extruded starches were less degraded than those of their native and hydroxypropylated corn starch counterparts. Similarly, increasing moisture content during extrusion lowered amylopectin degradation in the extruded starches. Increasing temperature during extrusion of cross‐linked hydroxypropylated starches at high moisture content (e.g., 40%) lowered amylopectin molecular weights of the extruded starches, whereas increasing extrusion temperature at low moisture content (30%) resulted in less degraded molecules. This difference was attributed to the higher glass transition temperatures of the cross‐linked starches.     

Starch Characteristics of the Rice Mutant du2‐2 Taichung 65 Highly Affected by Environmental Temperatures During Seed Development

The effects of environmental temperature (21 vs. 28°C) during rice seed development on the starch characteristics (apparent amylose content, amylopectin chain length distribution, and gelatinization properties) of nonwaxy Taichung 65 (T65), waxy Taichung (T65wx), du2‐2 mutated low‐amylose strain Taichung (76‐3/T65), and Koshihikari were studied. Amylose contents increased with decreasing environmental temperatures. Analysis of the amylopectin chain length distribution showed that the relative amounts of long chains with degree of polymerization (DP) > 25 in all starches decreased if maturation occurred at 21°C. Gelatinization onset, peak, and conclusion temperatures and enthalpies decreased with decreasing environmental temperatures. Of all starches studied, the du2‐2 mutated low‐amylose Taichung (76‐3/T65) was most affected by maturation temperatures. These results indicate that the du2‐2 mutated low‐amylose Taichung (76‐3/T65) may be a useful strain in understanding biochemical and genetic starch biosynthesis response to slight changes in temperature.     

Relationship of Gelatinization and Recrystallization of Cross‐Linked Rice to Glass Transition Temperature

Nonwaxy rice starch was cross‐linked with sodium trimetaphosphate and sodium tripolyphosphate to obtain different degrees of cross‐linking (9.2, 26.2, and 29.2%). The objective was to investigate the influence of cross‐linking on thermal transitions of rice starch. Starch suspensions (67% moisture) were heated at 2°C/min using differential scanning calorimetry (DSC) to follow melting transition of amylopectin. Biphasic transitions were observed at ≈60–95°C in all samples. Melting endotherms of amylopectin shifted to a higher temperature (≤5°C) with an increasing degree of cross‐linking, while there was no dramatic change in enthalpy. Recrystallization during aging for 0–15 days was significantly suppressed by cross‐linking. The delayed gelatinization and retrogradation in crosslinked starch were evident due to restricted swelling and reduced hydration in starch granules. Glass transition temperature (T_g) measured from the derivative curve of heat flow was ‐3 to ‐4°C. No significant change in T_g was observed over the storage time studied.     

Structural and molecular basis of starch viscosity in hexaploid wheat

Wheat starch is considered to have a low paste viscosity relative to other starches. Consequently, wheat starch is not preferred for many applications as compared to other high paste viscosity starches. Increasing the viscosity of wheat starch is expected to increase the functionality of a range of wheat flour-based products in which the texture is an important aspect of consumer acceptance (e.g., pasta, and instant and yellow alkaline noodles). To understand the molecular basis of starch viscosity, we have undertaken a comprehensive structural and rheological analysis of starches from a genetically diverse set of wheat genotypes, which revealed significant variation in starch traits including starch granule protein content, starch-associated lipid content and composition, phosphate content, and the structures of the amylose and amylopectin fractions. Statistical analysis highlighted the association between amylopectin chains of 18-25 glucose residues and starch pasting properties. Principal component analysis also identified an association between monoesterified phosphate and starch pasting properties in wheat despite the low starch-phosphate level in wheat as compared to tuber starches. We also found a strong negative correlation between the phosphate ester content and the starch content in flour. Previously observed associations between internal starch granule fatty acids and the swelling peak time and pasting temperature have been confirmed. This study has highlighted a range of parameters associated with increased starch viscosity that could be used in prebreeding/breeding programs to modify wheat starch pasting properties.     

Increase in Apparent Amylose Content and Change in Starch Pasting Properties at Cool Growth Temperatures in Mutant Wheat

Some mutant wheat lines with low‐amylose content were grown in a field and greenhouse (15 or 20°C) to compare apparent amylose content and starch pasting properties. The apparent amylose content of flour and starch increased and starch pasting parameters as measured by a Rapid Visco Analyser (RVA) changed in the greenhouse (at cool temperatures) during seed maturation. Densitometric analysis of the protein band separated by electrophoresis suggested that the increase in amylose content by cool temperature was related to the amount of Wx‐D1 protein. This data suggests that the Wx‐D1 gene was responsible for these changes. In wheat starch from Tanikei A6099 and Tanikei A6598 at 15°C, the value of final viscosity and total setback was higher than that from the field. In wheat starch from Tanikei A6599‐4 (waxy mutant with stable hot paste viscosity), the peak viscosity temperature was higher and time maintained >80% of the peak was shorter at 15°C than that from the field. Genetic analysis using doubled‐haploid (DH) lines from a combination of Tanikei A6599‐4 and Kanto 118 (low‐amylose line) showed that apparent amylose content increased and the starch pasting curve and properties changed in waxy progenies similar to Tanikei A6599‐4.     

Impact of Elevated Nighttime Air Temperatures During Kernel Development on Starch Properties of Field‐Grown Rice

The structural features of starch were examined to better understand the causes of variability in rice quality resulting from nighttime air temperature (NTAT) incidence during kernel development. Starch samples were isolated from head rice of four cultivars (Bengal, Cypress, LaGrue, and XL723) field‐grown in four Arkansas locations (Keiser, Pine Tree, Rohwer, and Stuttgart) in 2009 and 2010. Average NTATs recorded during the grain‐filling stages of rice reproductive growth in the four locations were 3.0–8.4°C greater in 2010 than 2009. Elevated NTATs altered the deposition of starch in the rice endosperm. Means pooled across cultivars and locations showed that amylose content was 3.1% (percentage points) less for the 2010 sample set. The elevated NTATs in 2010 resulted in a decrease in the percentage of amylopectin short chains (DP ≤ 18) and a corresponding increase in the percentage of long chains (DP ≥ 19) by an average of 1.3% (percentage points). The greater NTATs in 2010 also produced greater starch paste peak, final, and breakdown viscosities, whereas setback and total setback viscosities decreased. Changes in paste viscosity were highly correlated with the changes in the proportion of amylose and amylopectin. Onset gelatinization temperature was greater by 3.5°C, gelatinization enthalpy by 1.3 J/g, and relative crystallinity by 1.5% (percentage points) for the 2010 sample set. Changes in gelatinization parameters and granule relative crystallinity were highly correlated with the changes in amylopectin chain‐length distribution. Year × cultivar × location interaction effects were statistically insignificant, indicating that the four cultivars evaluated all showed some degree of susceptibility to the effects of temperature incidence during kernel development, regardless of the growing location.     

Impact of Soaking and Drying Conditions on Rice Chalkiness as Revealed by Scanning Electron Microscopy

Chalkiness is one of the most influential factors on head rice yield. Parboiling is known to be an effective way to remove chalkiness and improve head rice yield. However, the steps involved in the removal of chalkiness are still not completely resolved. This study investigated the effects of soaking temperature, soaking duration, and drying conditions on the removal of rice chalkiness. Chalky brown rice kernels were selected and soaked at 25, 65, 70, or 75°C for 3 h. After 1, 2, or 3 h, the rice samples were frozen before drying or immediately dried. Soaking at 25°C did not remove chalkiness and caused no morphological change in starch granules. When the soaking temperature increased from 25 to 65, 70, and 75°C, the chalkiness decreased from 100% to 34.1, 29.7, and 15.9%, respectively. Soaking rice at temperatures above the starch glass transition temperature but below the gelatinization temperature reduced chalkiness owing to rearrangement of starch granules and protein denaturation to fill the void spaces in the chalky area. During soaking, the morphology of starch granules also changed from round to angular in shape. Drying at temperatures above the starch glass transition temperature also facilitated rearrangement of starch granules to further reduce rice chalkiness.