Utilization of Hydroxypropylated Waxy Rice and Corn Starches in Korean Waxy Rice Cake to Retard Retrogradation

A traditional waxy rice gel cake in Korea, Injulmi, was prepared with hydroxypropylated waxy rice and corn starches (molar substitutions 0.13 and 0.11, respectively), and the textural and retrogradation characteristics of the cake were compared with a conventional cake made of waxy rice flour. In the pasting viscogram, hydroxypropylated starches exhibited reduced pasting temperatures, but increased peak viscosities compared with the unmodified starches. Under differential scanning calorimetry, the T_g′ and ice melting enthalpy of the starch gel cakes were reduced by hydroxypropylation, which indicated that the modified starches had higher water‐holding capacity than the unmodified starches. The degree of retrogradation, as measured by the hardness of the gel cake and the melting enthalpy, was significantly reduced by hydroxypropylation and hydroxypropylated waxy rice starch was more effective in retarding the retrogradation than hydroxypropylated waxy corn starch     

Comparison of Physical Properties of Wheat Starch Gels with Different Amylose Content

The effects of amylose content and other starch properties on concentrated starch gel properties were evaluated using 10 wheat cultivars with different amylose content. Starches were isolated from grains of two waxy and eight nonwaxy wheat lines. The amylose content of waxy wheat lines was 1.4–1.7% and that of nonwaxy lines was 18.5–28.6%. Starch gels were prepared from a concentrated starch suspension (30 and 40%). Gelatinized starch was cooled and stored at 5°C for 1, 8, 16, 24, and 48 hr. The rheological properties of starch gels were studied by measuring dynamic viscoelasticity with parallel plate geometry. The low‐amylose starch showed a significantly lower storage shear modulus (G′) than starches with higher amylose content during storage. Waxy starch gel had a higher frequency dependence of G′ and properties clearly different from nonwaxy starches. In 40% starch gels, the starch with lower amylose showed a faster increase in G′ during 48 hr of storage, and waxy starch showed an extremely steep increase in G′. The amylose content and concentration of starch suspension markedly affected starch gel properties.     

Gelatinization,Pasting, and Gelling Properties of Sweetpotato and Wheat Starch Blends

Sweetpotato starch is high yielding but has very limited uses. It is possible to expand its application by blending it with other starches to obtain novel properties. In this study, functional properties of the blends of native sweetpotato starch with native, acid‐thinned, and hydroxypropylated wheat starch were studied at different ratios (75:25, 50:50, 25:75). The swelling factor, extent of amylose leaching, pasting, and gel textural properties of the blends were nonadditive of their individual components, and could be mathematically modeled by quadratic equations in relation to the ratios. Two peaks during pasting were observed for some starch mixtures studied by Rapid ViscoAnalyser (RVA). The gelatinization and retrogradation enthalpies (ΔH) of the blends were additive of their individual components and could be modeled by linear equations. All starch mixtures exhibited two peaks during differential scanning calorimetry (DSC) scan for gelatinization, but a single peak for retrograded starches. This study may provide basis for formulation of mixtures using starch from diverse sources to develop more natural starch systems with a range of physicochemical properties.     

Water‐Barrier Property of Starch Films Investigated by Magnetic Resonance Imaging

Water‐barrier property of a starch film was investigated using a magnetic resonance imaging (MRI) technique with a two‐gelatin gel model system. A film was placed between two gels, which contained different amounts of sorbitol leading to high water activity (H‐gel) and low water activity (L‐gel) gels. The assembled model systems were used to investigate the changes of water status of gels during storage. A multislice‐multiecho pulse sequence was applied to acquire a series of transverse relaxation decay images, then spin‐spin relaxation time (T₂) of water protons of gelatin gels was calculated. The water migration from H‐gel to L‐gel and water redistribution within the gel during storage was evaluated based on the results of T₂ maps and T₂ profiles. The water transference rate was significantly influenced by the types of film used to separate the gels. The starch‐beeswax composite film had better water barrier ability than the starch fim. The combination of two‐gelatin gel model system and MRI techniques allowed the evaluation of the water‐barrier property of edible film prepared from biopolymers and also gave an insight into the physical structural change and chemical environmental conditions of gels due to water migration.     

Environmental factors that affect the ability of amylose to contribute to retrogradation in gels made from rice flour

Retrogradation in rice is a trait that describes the hardening of cooked rice after storage or cooling, and it has significant implications for many consumers of rice, since many people cook rice in the morning and consume it several hours later or the next day. Tools to select against retrogradation in breeding programs are yet to be described. Here, we aim to determine the effect on retrogradation of storage time and temperature and the role of starch, protein, and lipids using gels made from Koshihikari grown in either Australia or Japan. Immediately after cooking, cooling from 60 to 40 degrees C had a minimal effect on firmness, but cooling to 20 degrees C led to significantly firmer gels. Storing the gels at low temperatures did not have an additional effect on the firmness as compared with storing the gels at 20, 40, or 60 degrees C. The removal of proteins led to significantly softer gels at all storage treatments but did not affect the change in firmness on cooling. The removal of lipids increased the rate of retrogradation and the firmness of gels significantly for all treatments. Koshihikari grown in Japan retrograded much less than Koshihikari grown in Australia. The amount of amylose that could be washed from gels made from Australian flour was much greater than for gels made from Japanese flour. After storage, only low molecular weight amylose chains were released from the gel and only after rewarming them to 60 degrees C. Despite the fact that flours from both origins were 18% amylose, the amount of long amylose chains that were complexed with lipids was much greater for the Japanese rice, and the unavailability of the complexed long amylose chains explained the lack of retrogradation in the Japanese rice. Once the long chains were released from amylose-lipid complexes, the Japanese rice retrograded. Thus, the environmental factor affecting retrogradation in this variety is type or amount of lipids synthesized, and the degree of retrogradation was determined by the availability of long chains of amylose.     

Partial Characterization of Buckwheat (Fagopyrum esculentum) Starch

Laboratory-isolated buckwheat (Fagopyrum esculentum) starch was compared to commercial corn and wheat starches. Buckwheat starch granules (2.9–9.3 μm) were round and polygonal with some holes and pits on the surface. Buckwheat starch had higher amylose content, waterbinding capacity, and peak viscosity, and it had lower intrinsic viscosity when compared with corn and wheat starches. Buckwheat starch also showed restricted swelling power at 85–95°C and lower solubility in water at 55–95°C and was more susceptible to acid and enzymatic attack. Gelatinization temperatures, determined by differential scanning calorimetry, were 61.1–80.1°C for buckwheat starch compared to 64.7–79.2°C and 57.1–73.5°C for corn and wheat starches, respectively. A second endotherm observed at 84.5°C was an amylose-lipid complex attributed to the internal lipids in buckwheat starch, as evidenced by selective extraction. The retrogradation of buckwheat, corn, and wheat starch gels was examined after storage at 25, 4, and -12°C for 1–15 days. In general, buckwheat starch retrogradation was slower than that of corn and wheat starch, but it increased as storage time increased, as did that of the other starch pastes. When the values of the three storage temperatures were averaged for each storage period analyzed, buckwheat starch gels showed a lower percentage of retrogradation than did corn and wheat starch gels. Buckwheat starch also had a lower percentage of water syneresis when stored at 4°C for 3–10 days and had better stability to syneresis after three freeze-thaw cycles at -12 and 25°C.     

Effect of Polarity of Complexing Agents on Thermal and Rheological Properties of Rice Starch Gels

The ability of rice starch to complex with ligands of various polarities was studied to examine the mechanism of complex formation in an aqueous solution. Differential scanning calorimetry (DSC) showed that TNuS19 rice starch (27.9% amylose) formed inclusion complexes with all 12-C complexing agents. The onset melting temperatures (T_o) of the complexes were ≈93–96°C. The saturation concentrations of added ligands with high polarity, lauric acid (LA), and lauryl alcohol (LOH), had a range of 2–4% (w/w) of the starch, and both of the corresponding melting enthalpies (ΔH) were ≈3.0 J/g. In contrast, the saturation concentrations of ligands with low polarity, methyl laurate (ML) and dodecane (DO), were ≈1–2% (w/w), and the ΔH were 1.87 and 1.80 J/g, respectively. This implied that solubility of ligands had a significant effect on the extent of complexation. The T_o and ΔH increased with an increase of annealing time at 85°C, and the optima for the partially reversible complex formation were 2 hr of annealing in all cases. When measured by a dynamic rheometer, the TNuS19 rice starch gel with added LA or LOH showed a higher storage modulus (G′) than that with no complexing agent added during heating. The G′ and tan δ of the complexed gel were further increased during 12 hr of storage. The increase of G′ indicated that the elastic structure of the concentrated rice starch gels could be improved by complex formation and annealing, whereas the increase of tan δ suggested incompatibility of starch components during storage.     

Retrogradation of Rice Flour Gel and Dough: Plasticization Effects of Some Food Additives

Certain food additives commonly used in flour products also have a plasticization effect on product shelf life regarding retrogradation. Sucrose, sorbitol, glycerol, citric acid, and acetic acid at 25, 25, 25, 0.5, and 0.5%, respectively, were added to two different starch gel systems: slurry (high‐amylose rice flour gel) and dough (waxy rice flour dough). All plasticizers increased gelatinization temperature, decreased enthalpy (ΔH), and promoted a more homogeneous system. Sucrose had the greatest effect on gelatinization increase. Rice dough was more susceptible to plasticizers, resulting in higher moisture content and a more amorphous structure. Retrogradation was highly positively correlated with amylose content, moisture retention, ratio of protons of water/starch, and previous occurrence of retrogradation. Moisture retention was increased in plasticizer‐added samples, especially waxy rice dough. Over a longer storage period, sucrose and sorbitol showed an antiplasticization effect in waxy rice flour dough, but glycerol and acid caused higher retrogradation in high‐amylose rice flour gel.     

Rheological and Thermal Properties of Aged Starch Pastes from Three Waxy Maize Genotypes

The rheological and thermal properties of aged starch gels (15:85 starch-water) from three waxy maize genotypes (wx, wx sh1, and du wx) during storage (4°C for up to 25 days) were studied. After storage, changes of storage modulus (G′) and phase angle (δ) of the gels as a function of temperature were measured using oscillatory rheometry. For the du wx samples, G′ at 25°C increased rapidly during the first four days of storage at 4°C, compared to the gradual increases over the 25-day storage period for the wx and wx sh1 samples. A peak in G′ at 45°C was observed during heating for the du wx samples after 10 days of storage and for the wx sample stored for 25 days. The G′ peak may have been due to syneresis in the gels. Retrogradation of amylopectin of the aged starch samples was examined using differential scanning calorimetry. The du wx starch had greater retrogradation enthalpies than the other two samples (which showed similar retrogradation behavior) throughout the storage. The retrogradation enthalpy of the du wx samples increased rapidly during the first seven days, followed by a slower increase through the rest of storage. For the wx and wx sh1 samples, no endotherm was observed during the first four days of storage, after which the enthalpy increased steadily as a function of storage time. Addition of sucrose delayed the formation of gel networks for all three starches. The greater tendency for gelling and retrogradation of the du wx starch might be attributed to the greater proportion of DP20–30 chains of the amylopectin.     

Effect of Sucrose on Glass Transition,Gelatinization, and Retrogradation of Wheat Starch

Differential scanning calorimetry (DSC) was used to study the effect of sucrose on wheat starch glass transition, gelatinization, and retrogradation. As the ratio of sucrose to starch increased from 0.25:1 to 1:1, the glass transition temperature (T_g, T_g′) and ice melting enthalpy (ΔH_ice) of wheat starch‐sucrose mixtures (with total moistures of 40–60%) were decreased to a range of −7 to −20°C and increased to a range of 29.4 to 413.4 J/g of starch, respectively, in comparison with wheat starch with no sucrose. The T_g′ of the wheat starch‐sucrose mixtures was sensitive to the amount of added sucrose, and detection was possible only under conditions of excess total moisture of >40%. The peak temperature (T_m) and enthalpy value (ΔH_G) for gelatinization of starch‐sucrose systems within the total moisture range of 40–60% were increased with increasing sucrose and were greater at lower total moisture levels. The T_g′ of the starch‐sucrose system increased during storage. In particular, the significant shift in T_g′ ranged between 15 and 18°C for a 1:1 starch‐sucrose system (total moisture 50%) after one week of storage at various temperatures (4, 32, and 40°C). At 40% total moisture, samples with sucrose stored at 4, 32, and 40°C for four weeks had higher retrogradation enthalpy (ΔH) values than a sample with no sucrose. At 50 and 60% total moisture, there were small increases in ΔH values at storage temperature of 4°C, whereas recrystallization of samples with sucrose stored at 32 and 40°C decreased. The peak temperature (T_p), peak width (δT), and enthalpy (ΔH) for the retrogradation endotherm of wheat starch‐sucrose systems (1:0.25, 1:0.5, and 1:1) at the same total moisture and storage temperature showed notable differences with the ratio of added sucrose. In addition, T_p increased at the higher storage temperature, while δT increased at the lower storage temperature. This suggests that the recrystallization of the wheat starch‐sucrose system at various storage temperatures can be interpreted in terms of δT and T_p.     

Physicochemical Properties and In Vitro Starch Digestibility of Cooked Rice from Commercially Available Cultivars in Canada

The influence of amylose content, cooking, and storage on starch structure, thermal behaviors, pasting properties, and rapidly digestible starch (RDS), slowly digestible starch (SDS), and resistant starch (RS) in different commercial rice cultivars was investigated. Long grain rice with high‐amylose content had a higher gelatinization temperature and a lower gelatinization enthalpy than the other rice cultivars with intermediate amylose content (Arborio and Calrose) and waxy type (glutinous). The intensity ratio of 1047/1022 cm^–1 determined by Fourier Transform Infrared (FT‐IR), which indicated the ordered structure in starch granules, was the highest in glutinous and the lowest in long grain. Results from Rapid ViscoAnalyser (RVA) showed that the rice cultivar with higher amylose content had lower peak viscosity and breakdown, but higher pasting temperature, setback, and final viscosity. The RDS content was 28.1, 38.6, 41.5, and 57.5% in long grain, Arborio, Calrose, and glutinous rice, respectively, which was inversely related to amylose content. However, the SDS and RS contents were positively correlated with amylose content. During storage of cooked rice, long grain showed a continuous increase in pasting viscosity, while glutinous exhibited the sharp cold‐water swelling peak. The retrogradation rate was greater in rice cultivars with high amylose content. The ratio of 1047/1022 cm^–1 was substantially decreased by cooking and then increased during storage of cooked rice due to the crystalline structure, newly formed by retrogradation. Storage of cooked rice decreased RDS content and increased SDS content in all rice cultivars. However, no increase in RS content during storage was observed. The enthalpy for retrogradation and the intensity ratio 1047/1022 cm^–1 during storage were correlated negatively with RDS and positively with SDS (P ≤ 0.01).     

莲子淀粉品质对莲子汁流变特性和保质期影响的研究

淀粉品质是影响淀粉类食品品质的主要因素,优选低含量直链淀粉的莲子为原料是确保莲子产品品质的关键。本研究收集了中国具有代表性的22个野生及栽培莲子品种,并测定各品种直链淀粉含量(AC),按AC梯度从中选择7个莲子品种为原料分别制作莲子汁,研究莲子汁的流变特性和贮存过程中淀粉返生所致的流变性质变化,利用逐步回归法,建立莲子汁返生沉淀量与直链淀粉含量、贮存时间之间的数学模型。结果表明：莲子直链淀粉含量品种间差异较大,莲子汁为假塑性流体,淀粉在返生过程中黏度呈下降趋势,直链淀粉含量越高,黏度在贮存初期下降越快。莲子汁返生沉淀量与直链淀粉含量、贮存时间之间的数学模型为：Y=0.5107exp(0.020T-7.562×10^-5T²+9.955×10^-8T³+0.05C-0.001C²),该模型为莲子汁保质期预测和莲子优质育种目标提供理论依据,同时对淀粉质食品深加工开发也具有重要的参考价值。     

Model approach to starch functionality in bread making

We used modified wheat starches in gluten-starch flour models to study the role of starch in bread making. Incorporation of hydroxypropylated starch in the recipe reduced loaf volume and initial crumb firmness and increased crumb gas cell size. Firming rate and firmness after storage increased for loaves containing the least hydroxypropylated starch. Inclusion of cross-linked starch had little effect on loaf volume or crumb structure but increased crumb firmness. The firming rate was mostly similar to that of control samples. Presumably, the moment and extent of starch gelatinization and the concomitant water migration influence the structure formation during baking. Initial bread firmness seems determined by the rigidity of the gelatinized granules and leached amylose. Amylopectin retrogradation and strengthening of a long-range network by intensifying the inter- and intramolecular starch-starch and possibly also starch-gluten interactions (presumably because of water incorporation in retrograded amylopectin crystallites) play an important role in firming.     

Pulsed Nuclear Magnetic Resonance (PNMR) Study of Rice Starch Retrogradation

Although pulsed NMR (PNMR) has been used for qualitative study of starch retrogradation in selected systems, validation is necessary for its application to new systems. PNMR was used to analyze the retrogradation of rice starches in purified form, in rice flour, and in cooked rice grains. The standard curves between the relative solid content (S′, %) by PNMR and the percentage of gelatinized starch (GS, %) were determined for common rice flour, common rice starch, and waxy rice starch at different moisture contents. The coefficients of linear regression for these curves (R²) were all >0.997. Starches with different amylose contents were tested for S′ values at the stages of freshly gelatinized, retrograded (4°C, 18 days), and reheated (90°C, 20 min). The S′ of reheated starch (S′_reheat) was similar to the S′ of freshly gelatinized starch (S′₀), so we concluded that the increase in S′ during storage corresponded to amylopectin retrogradation. The effect of moisture content on retrogradation of rice starch, rice flour, and cooked rice grains was studied by PNMR, and the data were interpreted using the Avami equation. Decreasing the moisture content increased the rate of retrogradation and led to a higher parameter k and a lower parameter n. For moisture content in the range studied, PNMR can be used to follow amylopectin retrogradation of different rice starch systems.     

Water dynamics and retrogradation of ultrahigh pressurized wheat starch

The water dynamics and retrogradation kinetics behavior of gelatinized wheat starch by either ultrahigh pressure (UHP) processing or heat are investigated. Wheat starch completely gelatinized in the condition of 90, 000 psi at 25 degrees C for 30 min (pressurized gel) or 100 degrees C for 30 min (heated gel). The physical properties of the wheat starches were characterized in terms of proton relaxation times (T2 times) measured using time-domain nuclear magnetic resonance spectroscopy and evaluated using commercially available continuous distribution modeling software. Different T2 distributions in both micro- and millisecond ranges between pressurized and heated wheat starch gels suggest distinctively different water dynamics between pressurized and heated wheat starch gels. Smaller water self-diffusion coefficients were observed for pressurized wheat starch gels and are indicative of more restricted translational proton mobility than is observed with heated wheat starch gels. The physical characteristics associated with changes taking place during retrogradation were evaluated using melting curves obtained with differential scanning calorimetry. Less retrogradation was observed in pressurized wheat starch, and it may be related to a smaller quantity of freezable water in pressurized wheat starch. Starches comprise a major constituent of many foods proposed for commercial potential using UHP, and the present results furnish insight into the effect of UHP on starch gelatinization and the mechanism of retrogradation during storage.     

Molecular and Gelatinization Properties of Rice Starches from IR24 and Sinandomeng Cultivars

The differences in pasting properties involving gelatinization and retrogradation of rice starches from IR24 and Sinandomeng cultivars during heating‐cooling processes were investigated using a Rapid Visco Analyser (RVA)and a dynamic rheometer. The results were discussed in relation to the molecular structure, actual amylose content (AC), and concentration of the starches. Generally, both starches possessed a comparable AC (≈11 wt%), amylose average chain length (CL), iodine absorption properties, and dynamic rheological parameters on heating to 95°C at 10 wt% and on cooling to 10°C at higher concentrations. In contrast to Sinandomeng, IR24 amylose had a greater proportion of high molecular weight species and number‐average degree of polymerization (DP_n). IR24 amylopectin possessed a lower DP_n and greater CL, exterior CL (ECL), and interior CL (ICL). Comparing the results of RVA analysis and dynamic rheology, the gelatinization properties and higher retrogradation tendencies of IR24 starch can be related to the structural properties and depend on starch concentration. In addition, the exponent n of starch concentration for storage moduli at 25°C (G′₂₅ ∝ Cⁿ) increased linearly with increasing AC.     

Influence of Starch and Gluten Characteristics on Rheological Properties of Wheat Flour Gel at Small and Large Deformation

Starch and gluten were isolated from 10 wheat cultivars or lines with varied amylose content. The rheological properties of 30% wheat flour gel, starch gel, and the gel of isolated gluten mixed with common starch were determined in dynamic mechanical testing under shear deformation, creep‐recovery, and compression tests under uniaxial compression. Variation of wheat samples measured as storage shear modulus (G′), loss shear modulus (G″), and loss tangent (tan δ = G″/G′) was similar between flour and starch gels and correlated significantly between flour and starch gel. The proportion of acetic acid soluble glutenin exhibited a significant relationship with tan δ of gluten‐starch mixture gel. The small difference in amylose content strongly affected the rheological parameters of flour gels in creep‐recovery measurement. Wheat flour gel with lower amylose content showed higher creep and recovery compliance that corresponded to the trend in starch gel. Compressive force of flour gel at 50 and 95% strain correlated significantly with that of starch gel. Gel mixed with the isolated gluten from waxy wheat lines appeared to have a weaker gel structure in dynamic viscoelasticity, creep‐recovery, and compression tests. Starch properties of were primarily responsible for rheological changes in wheat flour gel.     

Elucidation of Fermentation Effect on Rice Noodles Using Combined Dynamic Viscoelasticity and Thermal Analyses

Natural fermentation of whole polished rice grains (indica) is a traditional processing method widely applied in China and South Asia to improve the texture of rice noodles. To elucidate the effects of fermentation on noodle texture, thermal analysis of rice flour and rheological measurement were performed on a gel made from the rice flour with the same solids concentration as practical noodles. The test method proved useful for monitoring starch granule swelling, gel forming, and retrogradation of rice gels during rice noodle production. Dynamic viscoelasticity in a temperature ramp sweep test showed that starch granules of the fermented sample swelled more and were more resistant to breakdown than those of the nonfermented sample. Differential scanning calorimetry revealed that the gelatinization temperature of fermented rice flour shifted to a lower temperature. The decreased protein content after fermentation also played a role in the modified rheological and thermal properties of fermented rice flour. Both fermented and nonfermented rice flour formed an elastic gel just after heating to the conclusion temperature of gelatinization (T_c). The fermented rice flour gel formed earlier with a well‐formed structure; however, it had slower retrogradation during aging. The result also indicated that the retrogradation of amylopectin impaired the desired texture of rice noodles.     

Rheological Properties of Fermented Rice Flour Gel

To clarify the rheological properties of fermented rice noodle (sour mifen) produced in South China, we studied the mechanical properties of gels made from fermented and nonfermented (control) rice flours using static tensile testing, two-bite testing, and dynamic viscoelastic measurement. Rheological measurement under large deformation showed that retrogradation in fermented rice gel proceeded more slowly than in nonfermented rice gel. Lower hardness and brittleness and higher cohesiveness and resilience (degree of recovery) for gels made from fermented rice flour demonstrated that the gel was less firm but more elastic and flexible. Storage moduli of both types of gel increased with time, but the starch retrogradation was suppressed for fermented rice gel. Fermented rice gel exhibited higher resilience and lower rigidity than nonfermented gel, thus the gel stability improved. The chemical analysis of both starches suggests that the partial hydrolysis of amylopectin occurred during the fermentation process.     

Chemical and Physicochemical Properties of Maize Starch After Industrial Nixtamalization

Processing conditions similar to traditional nixtamalization are now used by the industry in the production of dry maize flours (DMF). The objective of this investigation was to evaluate the effect of industrial nixtamalization on maize starch. Thus, dent maize grains were sampled from storage silos and the starch isolated (S). From the same batch of maize, DMF was obtained and the starch isolated (S‐DMF). The amylose content in the starches was quite similar (21.5–23.4%) and characteristic of a dent maize. However, nixtamalization increased the calcium content in S‐DMF. The starches investigated exhibited the typical A‐type diffraction pattern after 40 days of storage at 11–84.1% rh. However, the differential scanning calorimetry (DSC) results showed that annealing of maize starch occurred during storage at 30°C. On the other hand, industrial nixtamalization has both a melting and annealing effect on maize starch. Thus, the operative glass transition temperature (T_g), and the DSC parameters that define starch gelatinization (T_p and ΔH) showed that the proportion between crystalline and amorphous regions within the starch granule and the extent of physical damage to starch were modified by nixtamalization. As an example, T_g for S was between 60 and 62.5°C, while the S‐DMF had a T_g of 45–55°C for damaged starch and 65–70°C for annealed starch. Additionally, the extraction of the nonconstitutive starch lipids provided starches with more consistent thermal properties, particularly in the behavior of gelatinization at different water content. This last observation might have important implications in the consistency of starch physicochemical properties and, consequently, in the quality of maize products such as tortillas.