Evaluation of embedding strength on Uruguayan wood to apply the European yield theory for double shear bolted joint

The main objective of this study was to evaluate embedding strength on Uruguayan wood to apply the European yield theory (EYT) for double shear bolted joints’ on Eucalyptus grandis H.(EGH). To introduce the dowel-type connection performance, double shear tests were conducted. The embedding tests were conducted to calculate the yield strength of bolted joint by EYT and the compression test, to estimate the embedding strength. The yield strength obtained from the experiments showed a good agreement with the yield strength calculated by EYT method. The yield strength of double shear bolted joint evaluated from compressive strengths is a very close to the yield strength calculated by EYT. The average value and variability of the yield strength of double shear bolted joint calculated by EYT applying the embedding strengths of experimental results were very close to the yield strength or 5 % offset method of experimental results. The results from this study showed a good behavior to structural design with EGH in accordance to the Japanese standard code.     

Load-carrying capacity of steel-to-timber joints with a pretensioned bolt

Previous experimental studies reported that bolt pretensioning greatly increases the initial stiffness and load-carrying capacity of bolted joints. It is also a matter of great importance to structural designers to understand the effect of pretension on the load-carrying capacities of bolted joints, and this study presents an extended yield model that considers the fastener’s pretension force. In the extended yield model, the load-carrying capacity was defined as the load at a slip of 15 mm. The ultimate fastener bending angle at the yielded cross section equivalent to this joint slip, which was affected by the fastener’s axial force, was iteratively evaluated in numerical analyses. The introduction of bolt pretensioning largely increased the joint slip resistance at initial loading, but it decreased the ultimate fastener bending angle. This decrease of fastener bending angle resulted in a relatively low stiffness hardening (or secondary stiffness), which is caused by secondary axial forces associated with embedment of steel plates into the wood member. Prediction was verified by the tests of 36 steel-to-timber joints under three different pretension forces and two loading directions relative to the grain. Some of the observed load-carrying capacities of the joints, particularly in loading perpendicular to the grain, however, were not as high as those expected by the numerical analyses considering the given pretension forces.     

Determination of embedding strength of wood for dowel-type fasteners

Embedding tests parallel and perpendicular to the grain were conducted to produce a database of embedding strength of wood for the design of dowel-type joints. Dowel diameters were 8,12,16, and 20mm. Embedding strength was evaluated by the 5% off-set method and a maximum load up to 5mm displacement according to EN383. The embedding strength parallel to the grain evaluated by the former method showed values close to those obtained with the latter method, but they showed a significant difference in tests conducted perpendicular to the grain. The embedding strength parallel to the grain was 0.9 times as large as the compressive strength parallel to the grain regardless of the evaluation method. The embedding strength perpendicular to the grain evaluated by the 5% off-set method was four times as large as the compressive strength perpendicular to the grain. When the embedding strength perpendicular to the grain was evaluated by a maximum load up to 5mm displacement according to EN383, the ratio of embedding strength perpendicular to the grain to the compressive strength perpendicular to the grain decreased as the dowel diameter increased.Part of this paper was presented at the annual meeting of the Architectural Institute of Japan 1999, Hiroshima, September 1999; the 50^th annual meeting of the Japan Wood Research Society, Kyoto, April 2000; and the World Conference on Timber Engineering 2000, Whistler, Canada, July–August, 2000     

Fracture of multiply-bolted joints under lateral force perpendicular to wood grain

The crack initiation and propagation of multiplybolted joints subjected to lateral forces perpendicular to the grain were analyzed. Two types of bolted joint were subjected to lateral loads perpendicular to the grain. One had joints of two bolts aligned with the wood grain (type H), and the other had joints of two or three bolts aligned perpendicular to the grain (type V). The crack initiation and propagation were analyzed by means of the average stress method (ASM) and linear elastic fracture mechanics (LEFM), respectively. The maximum loads calculated by LEFM agreed comparatively well with the experimental results, and it was proved that the LEFM was an appropriate tool to analyze the fracture of multiply-bolted joints subjected to a force perpendicular to the grain. It was also found that the multiply-bolted joints failed with the fracture of the wood before the joints yielded, and that it caused a considerable decrease of the maximum loads. The reduction of strength should be considered in the design of multiply-bolted joints subjected to lateral forces perpendicular to the grain.Part of this work was presented at the annual meeting of the Architectural Institute of Japan, Hikone, September 1996     

Estimation of shear strength of dowel-type timber connections with multiple slotted-in steel plates by European yield theory

The shear strength of dowel-type timber connections with multiple slotted-in steel plates was estimated based on European yield theory. The values calculated based on the yield theory were compared with experimentally obtained results. An experiment was performed on dowel-type timber connections with two and three slottedin steel plates under lateral loads parallel to the grain. The yield mode of the dowel-type connection assumed in this study corresponds approximately to the failure mode of the connection obtained from the experiment. The shear strength of the dowel-type connections calculated based on the yield theory showed good agreement with the results for shear strength obtained in the experiment. The yield theory was useful for estimating the shear strength of the doweltype connection with multiple slotted-in steel plates. The shear strength of the dowel-type connection was greatly affected by the spacing of the steel plates, the number of steel plates, and the timber thickness. The values of these parameters that showed the proper shear strength of the dowel-type connection could be estimated based on the yield theory. Part of this paper was presented at the 9th Timber Engineering Forum of the Japan Timber Engineering Society, December 2005     

Prediction of the load carrying capacity of bolted timber joints

Failure of bolted timber joints is analyzed experimentally and numerically. In this study, the prediction of the load-carrying capacity of dowel-type joints with one dowel under static loading is based on the analysis of fracture in wood contrarily to most engineering methods that are based on the yield theory. Mechanical joints consist of glued laminated spruce members and steel dowels. In the different analyzed tests, the bolt loads the wood parallel or perpendicular to the grain. The wood member thickness is chosen sufficiently thin to avoid the fastener from presenting plastic hinges. The influences of different structural parameters such as the dowel diameter, the edge- and end-distances are investigated. The fracture propagation analysis is carried out with the Finite Element (FE) method in the framework of Linear Elastic Fracture Mechanics (LEFM). The only identified parameter is the critical energy release rate in mode I (G_Ic). The comparison between experimental and numerical results shows that the fracture must be considered for a correct prediction of the ultimate load and that LEFM can help to improve design codes. Received 11 August 1997     

Nonlinear superposition model for the behavior of bolted joints

Summary A previously developed model to predict the load-slip relationship for mechanical joints using one bolt subjected to lateral loading (Part 1) was extended to incorporate the rotational resistance of joints containing two bolts. The rotation is about the long axis direction of the bolts, and considers the wood members oriented at arbitrary angles to the grain. The model utilizes nonlinear translational springs to represent the parallel and perpendicular to grain components of the reaction force present on each bolt resisting the applied moment. A series of experiments were conducted to determine the spring constants of bolted joints in axial loading and to verify the predictions of the mathematical model. Bolted joints subjected to a pure rotation were tested using combinations of steel plates and wood side members experiencing bolt reaction forces at various angles of load to grain. The results indicated an excellent agreement between theoretical predictions and experimentally obtained data.The authors wish to extend thanks to the Colorado State Agricultural Experiment Station for their financial support and to the Fulbright-Hayes Foundation for the educational scholarship and research funding provided to the project     

Nonlinear superposition model for the behavior of bolted joints

Summary A nonlinear superposition model was developed to assess the load-slip behavior of bolted joints consisting of a single bolt subjected to lateral loading at angles of load to grain. This model characterizes the bolted joint as a pair of orthogonal nonlinear springs aligned parallel and perpendicular to the grain of the wood members. The spring stiffnesses are quantified by a logarithmic or exponential function depending upon whether the connection softens or stiffens with increasing slip. The spring deformations are superimposed to determine the movement of each component of the connection. Deformations of connected members are added vectorially to determine their relative displacement. Spring constant were determined experimentally using metal-to-wood connections. Thick steel side plates were employed to limit the system deformation to the wood component. Wood members were evaluated at angles of load to grain ranging from zero to ninety degrees. Once the spring constants had been determined, the model was executed to predict the load-slip behavior of wood-to-wood connections. These predictions were compared to experimentally obtained load-slip values. The results indicate that the nonlinear superposition concept is a valid approach to predict joint deformation at angles of load to grain.The authors express their gratitude to the Fulbright-Hays Foundation and the Colorado State Agricultural Experiment Station for their financial support of this study     

Effect of decay on shear performance of dowel-type timber joints

Monotonic and reversed cyclic loading tests were conducted on dowel-type timber joints with varying degrees of wood decay due to Fomitopsis palustris (Berk. et Curt.), a brown rot fungus, and the effect of decay on various shear performances of dowel-type joints was investigated. For joints affected by the brown rot fungus, the initial stiffness, yield load, and maximum load of dowel-type joints were significantly decreased, even with a small mass loss of wood. The reductions in shear performance were the largest for initial stiffness, followed by yield load and maximum load, in that order. For a 1% reduction of the yield load, initial stiffness and maximum load showed reductions of 1.15% and 0.77%, respectively. When dowel-type joints that had been exposed to the brown rot fungus were subjected to reversed cyclic loading, the gap between the dowel and the lead hole of the wood was increased and equivalent viscous damping was decreased. These results indicate that decay around the dowel lead hole especially affects the load-displacement behavior at small displacement level, and dowel-type joints under cyclic loading have very low resistance to forces acting on the wooden structure. Part of this report was presented at the 5th Symposium on Timber Bridges of the Japan Society of Civil Engineers, Tokyo, July 2006; the 56th Annual Meeting of the Japan Wood Research Society, Akita, August 2006; and the Annual Meeting of the Architectural Institute of Japan, Fukuoka, August 2007     

Static bending strength performances of cross-laminated woods made with five species

Thirty types of three-ply parallel- and cross-laminated woods were prepared from five species, and their static bending strength performance were investigated. The modulus of elasticity (MOE), proportional limit stress, and modulus of rupture (MOR) perpendicular to the grain were increased by cross-laminating, and the extent of the increase increased with decreasing density of the species. The measured values of MOE parallel and perpendi-cular to the grain of parallel-laminated woods and perpendicular to the grain of face laminae of cross-laminated woods were approximately equal to those calculated from true MOEs of individual laminae. However, the MOE parallel to the grain of face laminae of cross-laminated woods was much lower than the calculated MOE owing to the effect of the deflection caused by shear force on the MOE. The percentage of deflection caused by shear force versus total deflection (Y _s) showed high values, from 16.1% (buna) to 40.5% (sugi), and it decreased linearly with increasing shear modulus in the cross section of the core. In addition, there was an extremely high positive correlation between the MOR and the measured MOE parallel to the grain of face laminae of cross-laminated woods. The MOR was also highly dependent on the shear modulus in cross section of the core.Part of this paper was presented at the 50th Annual Meeting of the Japan Wood Research Society, Kyoto, April 2000     

Abrasive wear properties of compressed sugi wood

We examined the abrasive wear properties and the effect of abrasive grain size on the rate of wear when sugi wood (Cryptomeria japonica D.Don), compressed to various densities, was rubbed with abrasive paper. The results showed that the wear resistance of compressed wood increased linearly with the increased compression ratio; and under the condition of a low compression ratio it tended to be higher in comparison with the strength of compressed wood. The critical grain size effect, which can be witnessed during the abrasive wear of metals and plastics, was seen when low pressure was applied to the abrasive material. At higher pressures, the wear rate of the compressed wood increased with grain size, but the critical grain size effect was not observed. The pressure required to create the critical grain size effect was found to be higher than that needed for other types of uncompressed wood with the same yield properties.Part of this report was presented at the 50th Annual Meeting of the Japan Wood Research Society, Kyoto, April 2000     

An application of the Tsaï criterion as a plastic flow law for timber bolted joint modelling

Summary This paper describes a modelling approach to predict the behaviour of an elementary thin timber bolted joint. The application concerns principally joints with steel side members; bolts have a constant 12 mm diameter with two ratios of end distance to bolt diameter and two bolt clearances. The behaviour of the bolted joints is characterized by a double non linearity; the first one is due to the contact area evolution between the bolt and the hole of the jointed elements. The second one is owing to the evolution of plasticity on the wood. A spring element compatible with isoparametric plane finite elements represents the contact evolution. The elastic-plastic wood is provided with a plastic flow rule according to the Tsa? criterion. This study allows an investigation on the parameters characterizing the Tsa? criterion, particularly F₁₂ which represents the interaction between the principal axis of orthotropy. A two-dimensional model is used. It permits the assessment of the clearance bolt, joint dimensions, wood plasticity and wood grain angle effect on the joint behaviour. The wood grain angle has a non negligible effect on the plastic strains distribution and it can create a parasite loading because the joint tends to rotate even for an axial loading. The results showed a good agreement between experimental values given by some authors and numerically-predicted stresses on the joint. So, the applications concern a two-dimensional joint with anisotropic plastic material. The generalization in the three-dimensional modelling is desirable to take into account the interaction between the wood and a metallic fastener in thick joints with different geometric characteristics.     

Numerical analysis on tensile performance of bolted glulam joints with initial local cracks

Under varying climate conditions, cracks are commonly observed in bolted joints, owing to the shrinkage of wood and confinement from slotted-in steel plates and bolts. A three-dimensional finite element model was developed to investigate the mechanical behavior of bolted glulam joints with initial cracks. Wood foundation was prescribed in the model to simulate the local crushing behavior of wood surrounding the bolts. The behavior of wood in compression and the foundation were defined as transversely isotropic plastic in the software package ANSYS. Cohesive zone model was applied in the numerical analysis to consider the propagation of initial cracks and brittle failure of wood in the bolted joints under tension load. The numerical model was validated by the experiments conducted on full-scale specimens and it is indicated that the numerical model has good ability in predicting the failure modes and capacity of tension joints with local cracks. To further investigate the influence of crack number, length and locations, a parametric study was conducted with the verified model. Moreover, to study the effects of cracks on the behavior of bolted joints with different failure modes, another bolted joint including bolts with different strength grades and diameters was designed and analyzed in the parametric study, which was expected to have bolt yielding failure mode. It was found that the initial cracks can decrease the capacity and initial stiffness of tension joints by up to 16.5 and 34.8%, respectively.     

Effect of grain angle on shear strength of glued end grain to flat grain joints of defect-free softwood timber

To evaluate the effect of grain orientation on the adhesive bond strength, three-layered Norway spruce wood specimens were tested in shear. The two axial-oriented outer layers were jointed with the middle layer using three typical glues for load bearing constructions, i.e. one-component polyurethane (PUR), melamine–urea–formaldehyde (MUF) and phenol–resorcinol–formaldehyde (PRF). The grain orientation of the middle layers was varied from 0° (parallel to grain of the surface layer) to 90° (perpendicular to grain of the surface layer) in incremental steps of 10°. Samples with middle layers oriented parallel to the outer layers showed shear values in the range of solid spruce wood. Decreased shear strength values were expected for increased grain angles of the middle layer. However, no explicit tendency was observed for the shear strength in dependence of the grain direction. In general, MUF-bonded samples showed slightly higher shear strength values compared with PUR- and PRF-bonded specimens.     

竹节对竹材力学强度影响的研究

本文对毛竹和刚竹的带节材与不带节竹材的主要力学性质研究表明,带节竹材的抗弯强度、顺纹抗压、抗剪、抗拉强度和冲击韧性都有一定程度降低的趋向,但抗劈开强度和横纹抗拉强度却有明显提高。影响竹材力学强度的主要因素是维管束数量、维管束排列方向及维管束中纤维的力学强度,了解这些规律,对复合材料的结构仿生有重要参考作用。     

黄山马尾松顺纹剪切性能研究

参照ASTM D143标准对黄山马尾松进行顺纹剪切测试，结果表明，径切面剪切强度平均值为9.59MPa、弦切面剪切强度平均值为11.38MPa、45＆#176;纹理方向剪切强度平均值为11.15MPa。弦切面剪切强度略高于45＆#176;纹理方向剪切强度，径切面剪切强度最小。弦切面和径切面的剪切强度与密度均呈线性相关，密度越大，剪切强度越大。材料满足GB50005-2003《木结构设计规范》中对剪切强度的要求，可作为结构材使用。     

温度对人工林落叶松材物理力学性能的影响

探讨在不同的干燥温度状态下,木材抗弯强度,抗弯弹性模量、横纹抗压强度的变化规律。试验结果显示,在中、低温区域,随着温度的升高,抗弯弹性模量、横纹抗压强镁呈降低趋势;在高温区域,随着温度的升高,抗弯强度被明显削弱,而纹抗压强度则得到增强。     

Bearing properties of engineered wood products I: effects of dowel diameter and loading direction

The embedment tests of laminated veneer lumber (LVL) with two moduli of elasticity (MOE; 7.8 GPa and 9.8GPa), parallel strand lumber (PSL), and laminated strand lumber (LSL) were conducted in accordance with ASTM-D 5764. The load-embedment relation for each of these engineered wood products (EWPs) was established. The directional characteristics of bearing strength (_e), initial stiffness (k _e), and effective elastic foundation depth were obtained from the tested results. The effective elastic foundation depth (=E/k _e,E = MOE), based on the theory of a beam on elastic foundation, was obtained from thek _e and MOE. An of 90° (perpendicular to the grain) was calculated by dividingE ₉₀ [MOE of 90° from the compression test, but MOE of 0° (E ₀), parallel to the grain, obtained from the bending test] byk _e90, the initial stiffness of 90°. This study aimed to obtain the bearing characteristics of each EWP, taking into consideration their anisotropic structures, for estimating the fastening strength of a dowel-type fastener. The relations between the bearing coefficients ( _e,k _e,) on the loading direction and dowel diameter were established from the load-embedment curves. Based on the results of the embedment test, tested EWPs showed different tendencies in all directions from wood and glued laminated timber.Part of this study was presented at the 49th Annual Meeting of the Japan Wood Research Society, Tokyo, April 1999     

Effect of combinations of wood and counterface materials on three-body abrasive wear

The abrasion characteristics of various combinations of wood and counterface materials in three-body abrasive wear were investigated. Various wood samples were examined in combination with wood, plastic, and metal counterface materials. The wear coefficient in the wood samples was calculated as the wear volume of the friction surface divided by the sliding distance and the applied load. The results showed that the wear coefficient was smaller in cases where the wood samples had greater yield stress. The wear coefficient increased as the yield stress of the various counterface materials increased, reaching a maximum value and then decreased as the yield stress increased. This result indicated that a peak value existed for the wear coefficient in combination with the counterface material.Part of this report was presented at the 51st Annual Meeting of the Japan Wood Research Society, Tokyo, April 2001     

Derivation and application of an equation for calculating shear modulus of three-ply laminated material beam from shear moduli of individual laminae

In a detailed study of the relation between the deflection caused by shear force and the constitution of a laminated material beam, we derived an equation for calculating the shear modulus of a laminated material beam from the shear moduli of individual laminae. The validity of the derived equation was investigated using crosslaminated wood beams made with five species. The calculated shear moduli parallel to the grain of face laminae ranged from 48.3 MPa to 351 MPa, while those perpendicular to the grain of face laminae ranged from 58.0 MPa to 350 MPa. The calculated shear moduli increased markedly with increasing shear modulus in a cross section of perpendicular-direction lamina of a cross-laminated wood beam. The calculated apparent modulus of elasticity (MOE) of cross-laminated wood beams agreed fairly well with the measured apparent MOE values. This fact indicated that the apparent MOE of cross-laminated wood beam was able to be calculated from the true MOE values and shear moduli of individual laminae. The percentage of deflection caused by shear force obtained from the calculated apparent MOE (Y _sc) was close to that obtained from the measured apparent MOE (Y _s) and there was a high correlation between both values. From the above results, it was concluded that the derived equation had high validity in calculation of shear modulus of a cross-laminated wood beam.