Optimization of production of conjugated linoleic acid from soybean oil

Linoleic acid from soybean oil was used to synthesize conjugated linoleic acid (CLA), and the response surface methodology (RSM) was applied to optimize the process. A temperature of -35 degrees C and a solvent to oil sample ratio of 8 were suggested for removal of saturated fatty acids by low-temperature crystallization. The ratio of oil sample/urea/methanol suggested was 1:2:5.5 (w/w/v) for removal of oleic acid by urea crystallization. A temperature of 150 degrees C and a time of 140 min were found to be the optimal conditions in the isomerization for the production of c-9,t-11 and t-10,c-12 CLA isomers.     

Effects of temperature and agitation rate on the formation of conjugated linoleic acids in soybean oil during hydrogenation process.

The effects of hydrogen temperature and agitation rate on the formation of total conjugated linoleic acids (CLA) and CLA isomers were studied during hydrogenation with a selective Ni catalyst. The CLA isomers were identified by using a 100-m cyano-capillary column gas chromatograph and a silver ion-impregnated HPLC. Reaction temperature and agitation rate greatly affected the quantities of total CLA and individual CLA isomers, and the time to reach the maximum quantity of CLA in the partially hydrogenated soybean oil. As the hydrogenation temperature increased, the maximum quantity of CLA in soybean oil increased, but the time to reach the maximum CLA content decreased. By increasing the hydrogenation temperature from 170 to 210 degrees C, the quantity of CLA obtained was about 2.6 times higher. As the agitation rate decreased, the CLA formation in soybean oil increased, and the time to reach the maximum CLA content also increased. The maximum CLA contents in soybean oil obtained during hydrogenation at 210 degrees C with agitation rates of 300, 500, and 700 rpm were 162.82, 108.62, and 66.15 mg total CLA/g oil, respectively. The present data showed that it is possible to produce high-CLA-content soybean oil without major modification of fatty acid composition by short-time (10 min) selective hydrogenation under high temperature and low agitation rate conditions.     

Enrichment of conjugated linoleic acid in oats (Avena sativa L.) by microbial isomerization

A method for microbial isomerization of oat linoleic acid to conjugated linoleic acid (CLA) was developed. The method includes hydrolysis of oat lipids in aqueous flour slurries by the endogenous oat lipase. Then, the flour slurry containing free linoleic acid is utilized as a substrate for the isomerization reaction carried out by resting cells of Propionibacterium freudenreichii ssp. shermanii. The isomerization reaction progressed most effectively when, after the lipid hydrolysis period, the pH of the slightly acidic oat slurry was elevated to 8.0-8.5 and maintained at this range. With slurries containing 5% (w/v) oat flour, the amounts of CLA formed per dry matter were up to 10.1 mg/g corresponding to 102 mg/g lipids or 0.44 mg/mL slurry. Increments in the flour content up to 15% increased the volumetric production of CLA to 0.85 mg/mL. The proportion of the cis-9,trans-11 isomer was 80% of the total CLA formed. CLA could be concentrated into the solid material of the oat slurry by acidification.     

Photocatalytic production and processing of conjugated linoleic acid-rich soy oil

Daily intake of conjugated linoleic acid (CLA), an anticarcinogenic, antiatherosclerotic, antimutagenic agent, and antioxidant, from dairy and meat products is substantially less than estimated required values. The objective of this study was to obtain CLA-rich soybean oil by a customized photochemical reaction system with an iodine catalyst and evaluate the effect of processing on iodine and iodo compounds after adsorption. After 144 h of irradiation, a total CLA yield of 24% (w/w) total oil was obtained with 0.15% (w/w) iodine. Trans,trans isomers (17.5%) formed the majority of the total yield and are also associated with health benefits. The isomers cis-9,trans-11 and trans-10,cis-12 CLA, associated with maximum health benefits, formed approximately 3.5% of the total oil. This amount is quite significant considering that total CLA obtained from dairy sources is only 0.6%. ATR-FTIR, 1H NMR, and GC-MS analyses indicated the absence of peroxide and aldehyde protons, providing evidence that secondary lipid oxidation products were not formed during the photochemical reaction. Adsorption processing vastly reduced the iodine and iodocompounds without CLA loss. Photocatalysis significantly increased the levels of CLA in soybean oil.     

Conjugated linoleic acid isomers in partially hydrogenated soybean oil obtained during nonselective and selective hydrogenation processes

Partially hydrogenated soybean oil samples were collected during selective and nonselective hydrogenation processes. The formation of conjugated linoleic acids (CLAs) during hydrogenation was greatly dependent on the types and duration of hydrogenation processes. During hydrogenation processes, CLA contents increased initially. After reaching maximum CLA content, the content decreased during hydrogenation. Selective hydrogenation was much more favorable for the formation of conjugated linoleic acids. With nonselective hydrogenation process, the total CLA content was a maximum (9.06 mg total CLA/g oil) at 35 min. However, with the selective hydrogenation process, the total CLA content was a maximum (98.27 mg total CLA/g oil) at 210 min. The CLA contents in some of the tested selectively hydrogenated soybean oils were among the highest ever reported in foods.     

Formation of conjugated linoleic acids in soybean oil during hydrogenation with a nickel catalyst as affected by sulfur addition

The effects of sulfur addition on the formation of conjugated linoleic acid (CLA) isomers were studied during the hydrogenation of soybean oil with a nonselective type nickel catalyst. Sulfur addition greatly promoted CLA formation in soybean oil during hydrogenation. As the amount of sulfur increased to a certain level, the maximal quantity of CLA in soybean oil during hydrogenation increased greatly. However, further increase in sulfur addition above the certain level decreased CLA formation. The optimal sulfur level for the promotion of CLA formation differed greatly with the amount of nickel used. It was of great interest to find that the optimal ratio of sulfur to nickel for the promotion of CLA formation was always 0.06:1, regardless of the nickel amount used. At the same ratio of sulfur to nickel, higher nickel content induced significantly higher production of CLA (p < 0.05). At the optimal sulfur to nickel ratio, an increase in the nickel amount from 0.05 to 0.15% produced approximately 1.5 times higher levels of CLA during hydrogenation under the tested conditions. The CLA isomer compositions were greatly affected by both sulfur addition and amounts of nickel used for treatment. This is the first report of the possibility that the total quantity of CLA and their isomer composition could be manipulated during hydrogenation by controlling the amounts of sulfur and nickel.     

Microbially safe utilization of non-inactivated oats (Avena sativa L.) for production of conjugated linoleic acid

A microbially safe process for the enrichment of conjugated linoleic acid (CLA) in oats was developed. The process consists of hydrolysis of oat lipids by non-inactivated oat flour, followed by propionibacterium-catalyzed isomerization of the resulting free linoleic acid to CLA. The first stage was performed at water activity (a(w)) 0.7, where hydrolysis of triacylglycerols progressed efficiently without growth of the indigenous microflora of flour. Thereafter, the flour was incubated as a 5% (w/v) aqueous, sterilized slurry with Propionibacterium freudenreichii ssp. shermanii. The amount of CLA produced in 20 h was 11.5 mg/g dry matter corresponding to 116 mg/g lipids or 0.57 mg/mL slurry. The oat flour had also the capability to hydrolyze exogenous oils at a(w) 0.7. Sunflower oil, added to increase linoleic acid content in triacylglycerols 2.7-fold, was hydrolyzed rapidly. Isomerization of this oil-supplemented flour as a 5% slurry gave final CLA content of 22.3 mg/g dry matter after 50 h of fermentation, corresponding to 118 mg/g lipids or 1.14 mg/mL slurry. Storage stability of CLA in fermented oat slurries at 4 degrees C was good.     

Effect of antioxidants on soy oil conjugated linoleic acid production and its oxidative stability

Conjugated linoleic acid (CLA)-rich soy oil can be produced by photoisomerization of soy oil linoleic acid to produce a soy oil with up to 20% CLA. Recent studies indicate that mixed soy tocopherols added to refined bleached deodorized (RBD) oil produced significant increase in soy CLA yield during soy oil linoleic acid photoisomerization. However, the effect of common synthetic free radical scavenging antioxidants and specific tocopherols on CLA yield and its oxidative stability is not known. Therefore, this investigation evaluated the effects of various antioxidant systems on soy oil CLA yield and oxidative stability. Soy oil with added antioxidants consisting of combinations of mixed tocopherols (MT), ascorbyl palmitate (AP), butylated hydroxyanisole (BHA), butylated hydroxytoluene (BHT) and tert-butylhydroquinone (TBHQ) was photoisomerized to produce CLA- rich soy oil. The CLA content was determined by GC-FID analysis and oxidative stability by peroxide value (PV). The soy oil in the presence of TBHQ, MT alone and MT with 500 ppm of AP produced significantly greater CLA yields and improved oxidative stability compared to a control without added antioxidants (p < 0.05). However, added mixed tocopherols produced the greatest CLA yield and also reduced PV relative to the control. Tocopherols in the form of α-, γ- and δ-tocopherols were then each examined as to their relative effect on CLA yields and PV. The largest increase in CLA yield was obtained with 1800 ppm of γ-tocopherols with reduced PV. Mixed tocopherols, TBHQ and γ-tocopherols can be used to increase CLA yield and reduce PV of soy oil during linoleic acid photoisomerization.     

Antioxidant evaluation and oxidative stability of structured lipids from extravirgin olive oil and conjugated linoleic acid

Structured lipid (SL) was synthesized from extravirgin olive oil (EVOO) and conjugated linoleic acid (CLA) via a lipase-catalyzed reaction. CLA provides a variety of health benefits, but it is not consumed in free fatty acid form. The synthesized SL olive oil contained 42.5 mol % CLA isomers, and the major isomers were cis-9,trans-11-CLA (16.9 mol %) and trans-10,cis-12-CLA (24.2 mol %). The antioxidant activity determined by the radical scavenging capacity with the 2,2-diphenyl-1-picrylhydrazyl radical was lower in SL olive oil than in EVOO. The oxidative stability was also lower in SL olive oil since it had a higher peroxide value, rho-anisidine value, and 2-thiobarbituric acid reactive substances values during 20 days of storage at 60 degrees C. This observation could be due to the reduction in the natural phenolic compounds (97%) and tocopherols (56%), and the incorporated CLA with two conjugated double bonds in the SL olive oil. The oxidative stability of SL olive oil was increased by added rosemary extracts at concentrations of 100, 200, and 300 ppm. The present study suggests that the SL olive oil may be a suitable way to incorporate or deliver CLA into human diets. However, the addition of a proper antioxidant would be required for improving its oxidative stability.     

Measurement of conjugated linoleic acid (CLA) in CLA-rich potato chips by ATR-FTIR spectroscopy

A conjugated linoleic acid (CLA)-rich soy oil has been produced by photoisomerization of soy oil linoleic acid. Nutritional studies have shown that CLA possesses health benefits in terms of reducing certain heart disease and diabetes risk factors. Potato chips are snacks that are readily produced in the CLA-rich soy oil containing CLA levels similar to those of the oil used for frying. The objective of this study was to develop an FTIR method to rapidly determine the CLA content of oil in potato chips. Photoirradiated soy oil samples with ～25% total CLA were mixed with control soy oil, and 100 soy oil samples with total CLA levels ranging from 0.89 to 24.4% were made. Potato chips were fried using each of these 300 g CLA rich soy oil mixtures at 175 °C for approximately 3 min. Duplicate GC-FID fatty acid analyses were conducted on oil extracted from each batch of potato chips. The chip samples were ground and then scanned using ATR-FTIR spectroscopy with the aid of a high-pressure clamp, and duplicate spectra of each sample were averaged to obtain an average spectrum. Calibration models were developed using PLS regression analysis. These correlated the CLA isomer concentrations of potato chips obtained by GC-FID fatty acid analysis with their corresponding FTIR spectral features. The calibration models were fully cross validated and tested using samples that were not used in the calibration sample set. Calibrations for total CLA, trans,trans CLA, trans-10,cis-12 CLA, trans-9,cis-11 CLA, cis-10,trans-12 CLA, and cis-9,trans-11 CLA had coefficients of determinations (R2v) between 0.91 and 0.96 and corresponding root-mean-square error of prediction (RMSEP) ranging from 0.005 to 1.44. The ATR-FTIR technique showed potential as a method for the determination of the CLA levels in unknown potato chip samples.     

Identification of conjugated linoleic acids in hydrogenated soybean oil by silver ion-impregnated HPLC and gas chromatography-ion impacted mass spectrometry of their 4,4-dimethyloxazoline derivatives

Hydrogenated soybean oil was obtained after 10 min of hydrogenation with 0.5% selective type Ni catalyst at 230 degrees C, a hydrogenation pressure of 0.049 MPa, and an agitation rate of 300 rpm. The conjugated linoleic acid isomers in the hydrogenated soybean oil were isolated by using a silver ion-impregnated HPLC. Gas chromatography-mass spectrometry of 4,4-dimethyloxazoline (DMOX) derivatives of the isolated conjugated linoleic acid isomers were carried out for the identification of their chemical structures. By interpreting the mass spectra of the DMOX derivatives of conjugated linoleic acid isomers isolated by silver ion-impregnated HPLC, 20 different conjugated linoleic acid isomers present in hydrogenated soybean oil were identified. This is the first report for the mass spectrometric identification of the conjugated linoleic acid isomers present in hydrogenated vegetable oil.     

Partial inhibition of biohydrogenation of linoleic acid can increase the conjugated linoleic acid production of Butyrivibrio fibrisolvens A38

Butyrivibrio fibrisolvens A38, one of the most active rumen bacteria in conjugated linoleic acid (CLA) production, was characterized in vitro. Previous findings that some inhibitory levels of substrate for biohydrogenation (BH) by B. fibrisolvens A38 resulted in more CLA accumulation led to a prediction that partial inhibition of BH could increase ruminal CLA production. The inhibitory conditions for bacterial growth were less effective on the isomerization step than on the following reduction step. Linoleic acid (LA) was inhibitory not only to cell growth but also to LA hydrogenation, and this effect was greater at high concentrations. The reduction step, converting CLA to hydrogenated products (trans-C18:1 and C18:0), was significantly inhibited, and more CLA accumulated during aerobic incubation when LA was added along with a glycolytic inhibitor, iodoacetate (IAA), to cells that were pre-adapted to LA (1 g/OD at 600 nm/L, P < 0.05). Monensin was more inhibitory than IAA to cell growth but less effective for CLA accumulation. Rumen fluid in the culture medium appeared to activate BH even in an aerobic condition, resulting in a lower CLA level than the control group (P < 0.05). Because the isomerization and reduction steps are coupled reactions in BH of most hydrogenating bacteria including B. fibrisolvens A38 cells, both positive and negative modulations of the reduction steps could be key determinants for CLA accumulation in the rumen.     

Effect of extrusion parameters on conjugated linoleic acids of corn extrudates

The effects of extrusion temperature, 150-190 degrees C, and torque, 50-70%, on the content and configuration of conjugated linoleic acids (CLA) in corn extrudates were analyzed by GC and HPLC. At a temperature of 150 degrees C, CLA content increased from 1.2 mg/g of oil in feed to 7.8 mg/g of oil in corn extrudates. A decrease in total CLA (P < 0.05) was obtained when the product temperature was further increased to 190 degrees C. Alteration of CLA geometrical configuration was observed at higher extrusion temperatures. trans,trans-CLA significantly increased (P < 0.05) from 10.2% in feed to 11.9% of CLA at the extrusion condition of 190 degrees C and 70% torque. The highest expansion of extrudates was found at the product temperature of 150 degrees C and 70% torque. This extrusion condition also gave the maximum total CLA content and minimum trans,trans-CLA formation.     

Kinetics of photoirradiation-induced synthesis of soy oil-conjugated linoleic acid isomers

Photoirradiation of soy oil with UV/visible light has been shown to produce significant amounts of trans,trans conjugated linoleic acid (CLA) isomers through conversion of various synthesized intermediate cis,trans isomers. The objective of this study was to determine the kinetics of CLA isomers synthesis to better understand the production of various isomers. Soy oil was irradiated with UV/visible light for 144 h in the presence of an iodine catalyst and CLA isomers analyzed by gas chromatography (GC). Arrhenius plots were developed for the conversion of soy oil linoleic acid (A) to form cis-, trans/trans-, cis-CLA (B), conversion of cis-, trans/trans-, cis-CLA to form trans,trans-CLA (C) with respect to B, and formation of trans,trans-CLA isomers with respect to C. The kinetics of consumption of linoleic acid (LA) to form cis-, trans/trans-, cis-CLA was found to be of second-order with a rate constant of 9.01 x 10-7 L/mol s. The rate of formation of cis-, trans/trans-, cis-CLA isomers depends on the rate of formation from LA and its rate of consumption to form trans,trans-CLA isomers. The conversion of cis-, trans/trans-, cis-CLA isomers to trans,trans-CLA isomers was found to be of first-order with a rate constant of 2.75 x 10-6 s-1. However, the formation of thermodynamically stable trans,trans-CLA isomers (C) with respect to C was found to be a zero-order reaction with a rate constant of 10.66 x 10-7 mol/L s. The consumption of LA was found to be the rate-determining step in the CLA isomers formation reaction mechanism. The findings provide a better understanding of the mechanism of CLA isomers synthesis by photoirradiation and the factors controlling the ratio of various isomers.     

Effect of the degree of processing on soy oil conjugated linoleic acid yields

Photoirradiation processing can be used to rapidly synthesize conjugated linoleic acid (CLA) in large quantities in soy oil. The objective of this study was to evaluate the effect of the level of refining of soy oil on CLA yields and oxidative properties after photoirradiation. Crude, alkali-refined, alkali-refined bleached, and alkali-refined bleached and deodorized (RBD) soy oils were photoirradiated in a pilot-plant processing system for 12 h with 0.35% iodine catalyst at 47 degrees C. RBD soy oil gave the highest total CLA yield of 16.3% of total oil with 4.3% cis, trans- and trans, cis-CLA isomers. Oxidative stability as measured by weight gain during incubation at 64 degrees C showed that iodine decreased the induction time of soy oil samples by 2-4 days. Photoirradiation processing further decreased the induction time by 2 days as a result of loss of total tocopherols. Iodine addition increased the titratable acidity in all the samples of soy oil. However, the level of refining affects this increase of titratable acidity, and RBD soy oil was found to be the most stable. The study indicates that RBD soy oil was the most suitable candidate for photoirradiation processing. Thus, soy oil should be alkali-refined, bleached, deodorized, and then photoprocessed followed by a secondary adsorption step to remove the iodine catalyst to obtain a RBD CLA-rich soy oil.     

脉冲强光及抗氧化剂对大豆油过氧化的影响

通过化学滴定法测定脉冲强光处理的大豆油在贮藏过程中的过氧化值和酸价的变化,探讨脉冲时间、贮藏效应和抗氧化剂对大豆油氧化的影响。结果表明,随脉冲时间的增加,大豆油的氧化程度加剧。经脉冲强光处理的大豆油在不同温度下（4℃,37℃,60℃）的贮藏稳定性均有所下降;随贮藏温度的升高和脉冲时间（0～20s）的增加,油脂氧化速度加...     

Utilization of monolinolein as a substrate for conjugated linoleic acid production by Bifidobacterium breve LMC 520 of human neonatal origin

This study was designed to isolate bifidobacteria from human intestines that efficiently converts monolinolein, a monoglyceride form of linoleic acid, into conjugated linoleic acid (CLA), as well as to optimize culture conditions for improving CLA production during milk fermentation. Among 150 screened neonatal bifidobacteria, Bifidobacterium breve LMC 520 showed the highest CLA-producing ability and was tested with different types of fat substrates at various concentrations to determine the optimal conditions for CLA production. Monolinolein was tested as a substrate for CLA production. The incubation time optimized for CLA production was 24 h, and CLA production was proportionally increased with monolinolein concentration. The incubation of LMC 520 with commercial starter strains caused minimal reduction in CLA production. Our results demonstrate that the CLA-producing ability of B. breve LMC 520 could offer beneficial effects when utilized as a starter culture for the development of functional dairy products.     

Influence of feeding soybean oil on conjugated linoleic acid content in beef

Forty-eight steers were used to study the influence of feeding soybean oil (SO) on the conjugated linoleic acid (CLA) content of beef. Steers were fed either a control diet containing 954 g/kg of dry matter (DM) corn-based concentrate (CTL) or a control diet supplemented with SO at 20 (SO2) or 40 g/kg (SO4) of diet DM for 105 days. Adipose tissue samples were collected from the M. longissimus dorsi (LD) and from the M. semitendinosus (ST) on days 0 and 63 of the experiment. Adipose and muscle tissue samples were collected from the LD and ST immediately after slaughter. Feeding 40 g/kg of DM as SO increased the proportions of trans-C(18:1) in beef lipid as compared to CTL and SO2 treatments. The C(18:2) cis-9, trans-11 isomer of CLA as a proportion of total fat was not different in adipose and muscle across treatments. Supplementing SO increased C(18:2) trans-10, cis-12 CLA in adipose tissue of the LD. Supplementing high-grain finishing diets with SO is not an effective strategy to enhance the C(18:2) cis-9, trans-11 isomer of CLA in beef.     

Oxidative stability of conjugated linoleic acid isomers

Conjugated linoleic acids (CLAs) have been shown to be a strong anticarcinogen in a number of animal models. Our previous study demonstrated that CLA as a whole was extremely unstable in air. The present study was undertaken further to examine the oxidative stability of individual CLA isomers using the combination of gas-liquid chromatography (GLC) and silver ion high-performance liquid chromatography (Ag-HPLC). It was found that CLA as a whole oxidized rapidly and more than 80% was degraded within 110 h in air at 50 degrees C. Four c,c-CLA isomers were most unstable followed by four c,t-CLA isomers. In contrast, four t,t-CLA isomers were relatively stable under the same experimental conditions. Both the oxygen consumption and the GLC analysis revealed that 200 ppm jasmine green tea catechins (GTCs) exhibited protection to CLA and were even stronger than 200 ppm butylated hydroxytoluene (BHT) when added to either CLA or canola oil containing 10% CLA. The present study emphasized that oxidative unstability of CLA should not be overlooked although CLA has many biological effects.     

Effects of conjugated linoleic acid (CLA) isomers on oxygen diffusion-concentration products in liposomes and phospholipid solutions

Conjugated linoleic acids (CLAs) are a group of octadecadienoic acids (18:2) that are naturally present in food products and may have beneficial health effects. Liposomes and ethanol solutions were prepared by mixing synthetic phosphatidylcholines (PCs) with c9,t11-CLA, t10,c12-CLA, and linoleic acid (LA) in the sn-2 position into natural PCs from soybean, egg yolk, rat brain, and rat heart at 5 mol %. The oxygen diffusion-concentration products were measured using electron spin resonance spin-label oximetry methods. Individual synthetic PCs, the phospholipid matrix, and the tested lipid systems all exhibited influence on oxygen diffusion-concentration products during lipid peroxidation. Incorporating 5 mol % PC(c9,t11-CLA) into soy and egg yolk PC increased oxygen consumption in liposome suspensions while it was decreased in rat heart and brain PCs. On the other hand, PC(t10,c12-CLA) increased oxygen consumption in mixtures with egg yolk and rat heart PC but decreased it in soybean and rat brain PC. By comparison, PC(LA) decreased oxygen consumption in every case. In ethanol solutions, all of the synthetic PCs suppressed the capacity to generate peroxide radicals in the order of LA > c9,t11-CLA > t10,c12-CLA. In addition, PCs containing individual CLA isomers and LA differed in their capacities to react with and quench DPPH radicals in both ethanol solution and liposome, suggesting differences between CLA isomers and LA in DPPH radical-fatty acid interactions. Incorporation of CLA isomers and LA into dimyristyl-PC reduced the phase transition temperature from 23.6 to 23.1 and 23.3 degrees C, respectively. The results of this study provide evidence that the behavior of CLA isomers differs in the microenvironment of membranes possibly due to structural differences that affect the permeability of membranes to oxygen and lipid peroxidation.