Purge and trap method for determination of ethylene dibromide in table-ready foods

An improved method has been developed for the determination of ethylene dibromide (EDB, 1,2-dibromoethane) in a variety of table-ready foods. Samples are mixed with water and sparged with nitrogen for 1 h with stirring in a water bath at 100 degrees C. The EDB collected on the adsorbent Tenax TA is eluted with hexane and determined by gas chromatography (GC) with electron capture (EC) and confirmed with Hall electrolytic conductivity (HECD) detection using a second GC column. The highest levels of EDB were also confirmed by full scan GC/mass spectrometry (GC/MS). Twenty-five table-ready foods from the Food and Drug Administration's Total Diet Study that were analyzed by this method exhibited levels up to 70 ppb (pecans). Recoveries from fortified samples ranged from 91 to 104%. Values from this procedure were compared to those obtained by a modified Rains and Holder codistillation method. In all 25 samples this purge and trap procedure showed equivalent or superior recoveries and detected levels of EDB.     

Purge and trap method for determination of ethylene dibromide in whole grains, milled grain products, intermediate grain-based foods, and animal feeds

An improved method has been developed for the determination of ethylene dibromide (EDB; 1,2-dibromoethane) in whole grains, milled grain products, intermediate grain-based foods, and animal feeds. Samples are mixed with water and sparged with nitrogen for 1 h with stirring in a water bath at 100 degrees C. The EDB collected on the adsorbent Tenax TA is eluted with hexane and determined by gas chromatography (GC) with electron capture detection (ECD) and confirmed with Hall electrolytic conductivity detection (HECD) using a second GC column. The highest levels of EDB were also confirmed by full scan GC/mass spectrometry (GC/MS). A total of 24 whole grains, milled grain products, intermediate grain-based foods, and animal feeds analyzed by using this method contained EDB levels up to 840 ppb (wheat). Recoveries from fortified samples ranged from 90 to 105%. Values from this method were compared with those obtained from the acetone soak method; for all 24 samples, this purge and trap method gave equivalent or superior recoveries and detected levels of EDB. Chromatograms for this purge and trap method were clean, enabling a quantitation level of 0.5 ppb to be achieved.     

Semicarbazide formation in azodicarbonamide-treated flour: a model study

Semicarbazide was previously found in foods that were in contact with rubber gaskets foamed at high temperatures with a blowing agent azodicarbonamide. Because azodicarbonamide is an approved flour additive in certain countries, we set out to ascertain if semicarbazide is formed during the baking process from flours containing that additive. The levels of semicarbazide in baking flour treated with azodicarbonamide and bread baked from such flours were determined by isotope dilution (13C15N2-semicarbazide) liquid chromatography electrospray tandem mass spectrometry (LC-MS/MS). The samples were homogenized with HCl, extracted with n-pentane, derivatized with 2-nitrobenzaldehyde, and the derivative was extracted with ethyl acetate. After solvent exchange to 10% acetonitrile in water containing 0.1% acetic acid, the samples were analyzed using a 2.1 mm x 150 mm C18 column eluted with 2 mM ammonium formate in water/methanol (40:60). Semicarbazide was formed during the dry heating of commercial azodicarbonamide-containing flours at temperatures of 150-200 degrees C reaching levels of 0.2 mg/kg. Similar levels of semicarbazide were found in the crusts of breads made from azodicarbonamide-treated flour.     

Thermal degradation of sulforaphane in aqueous solution.

Sulforaphane, a cancer chemopreventive agent identified from broccoli, was degraded in an aqueous solution at 50 and 100 degrees C. The reaction mixtures were extracted with methylene chloride and analyzed by gas chromatography (GC) and gas chromatography/mass spectrometry (GC/MS). Dimethyl disulfide, S-methyl methylthiosulfinate, S-methyl methylthiosulfonate, methyl (methylthio)methyl disulfide, 1,2,4-trithiolane, 4-isothiocyanato-1-(methylthio)-1-butene, and 3-butenyl isothiocyanate were identified as volatile decomposition products. After methylene chloride extraction, the aqueous layer was dried and silica gel column chromatography was used to separate and purify the nonvolatile decomposition products. The major thermal degradation compound was determined by (1)H NMR, (13)C NMR, and FAB-MS as N, N'-di(4-methylsulfinyl)butyl thiourea. A possible mechanism for the formation of these products is proposed.     

Microdiffusion and fluoride-specific electrode determination of fluoride in foods

A simple and accurate method was developed for routine determination of fluoride in foods. Hydrogen fluoride is diffused 20 hr at 50 degrees C from fresh or freeze-dried samples (0.1 g dry wt) in polystyrene petri dishes containing 2 mL 40% HCIO4 and 0.3 g Ag2SO4, and is absorbed on the lids, previously spotted with 0.1 mL 0.5M NaOH. The absorbent layer is dissolved in 2 mL buffer solution, and the fluoride is measured potentiometrically. The method was verified by analysis of NBS Standard Reference Materials; recovery from 28 spiked infant foods (average = 99%, range = 75-135%); and comparison of results with colorimetry results for the same diffusates, after modification to handle 1 g samples. Relative standard deviations varied from 4 to 20% day to day. Detection limits were below 0.05 microgram/g dry weight.     

Rapid headspace gas chromatographic method for assessment of oxidative stability of cooked chicken meat

Experiments were conducted to determine the volatile compounds in cooked chicken meat using a static headspace gas chromatographic (GC) technique. Preheating conditions for samples in vials were tested at 70, 80, and 90 degrees C for 20-120 min at each temperature. The majority of the peaks increased in size as the temperature and time increased. Optimum conditions were established as preheating at 80 degrees C for 30 min followed by analysis on a packed column of 8% Poly MPE on Tenax GC with the temperature programmed from 50 to 200 degrees C at 10 degrees/min. Coefficients of variation for major peaks ranged from 8.3 to 14.7%. These results were compared with those obtained with a capillary column analysis of samples preheated at the same conditions. Cooked and stored chicken patties, pretreated with different levels of sodium tripolyphosphate, were analyzed by the thiobarbituric acid (TBA) method and the headspace GC technique. Significant positive correlations were obtained between TBA numbers and the areas of 3 major peaks of the headspace profiles, indicating the applicability of the rapid headspace GC method for the determination of oxidative changes in chicken meat.     

Simultaneous gas chromatographic determination of carboxylic acids in soft drinks and jams

A method was developed for simultaneous gas chromatographic determination of sorbic acid, dehydroacetic acid, and benzoic acid used as preservatives, and succinic acid, fumaric acid, malic acid, and tartaric acid used as acidulants in soft drinks and jams. A sample was dissolved in NH4OH-NH4Cl pH 9 buffer solution, and an aliquot of the solution was passed through a QAE-Sephadex A 25 column. The column was washed with water, and the carboxylic acids were eluted with 0.1N HCl. Sorbic acid, dehydroacetic acid, and benzoic acid were extracted with ethyl ether-petroleum ether (1 + 1), and determined on a 5% DEGS + 1% H3PO4 column. Succinic acid, fumaric acid, malic acid, and tartaric acid in the lower layer were derivatized with N,O-bis(trimethylsilyl)acetamide and trimethylchlorosilane, and determined on a 3% SE-30 column. Recoveries from soft drink and jam samples fortified with 0.1% each of 7 carboxylic acids ranged from 92.4 to 102.6% for preservatives, and from 88.1 to 103.2% for acidulants.     

Analysis of unsaponifiable compounds of edible oils by automated on-line coupling reversed-phase liquid chromatography-gas chromatography using the through oven transfer adsorption desorption interface

An automated method for analysis of unsaponifiable compounds in edible oils is presented. The method involves the on-line coupling of reversed-phase liquid chromatography and gas chromatography (LC-GC) using the through oven transfer adsorption desorption (TOTAD) interface. The oil is injected directly with no sample pretreatment step other than filtration. It may also be considered to dilute the oil sample. In the LC step, a short C4 column using a methanol/water eluent separates analytes from the other components of the oils, which are made up of mainly triglycerides. A LC fraction of up to 1.6 mL containing the analytes is transferred to GC at a flow rate of 0.1-2 mL/min. The TOTAD interface allows solvent venting and the introduction of the analytes into the GC column. The proposed fully automated method allows the analysis of different groups of compounds (free sterols, tocopherols, squalene, and erythrodiol and uvaol) in one chromatographic run or the analysis of these compounds in different groups. Sensitivity is more than necessary, and repeatability is good, the CV ranging from 3 to 12% for the full analysis.     

Purge and trap method for determination of volatile halocarbons and carbon disulfide in table-ready foods

A method developed for the determination of ethylene dibromide in table-ready foods has been modified and expanded to include 7 other volatile halocarbons and carbon disulfide. Samples are stirred with water and purged with nitrogen for 0.5 h in a water bath at 100 degrees C. The analytes collected on a duplex trap composed of Tenax TA and XAD-4 resin are eluted with hexane and determined by gas chromatography with electron capture detection or Hall electrolytic conductivity detection. Flame photometric detection in the sulfur mode is used to determine carbon disulfide. Thick-film, wide-bore capillary columns are used exclusively in both the determination and confirmation of the halogenated analytes. The higher levels of analytes are also confirmed by full scan gas chromatography mass spectrometry (GC/MS). Samples are analyzed for carbon disulfide, methylene chloride, chloroform, 1,2-dichloroethane, methyl chloroform, carbon tetrachloride, trichloroethylene, 1,2-dibromoethane, and tetrachloroethylene. Initially, 19 table-ready foods from the Food and Drug Administration's Total Diet Study were analyzed by this method. A limited survey of those food items exhibiting high levels of analytes was conducted. Samples exhibited levels up to 3300 ppb (methyl chloroform in Parmesan cheese). Recoveries of all 9 analytes from fortified samples ranged from 83 to 104%. Chromatograms from this purge and trap method are clean, enabling quantitation levels of low parts per billion and sub-parts per billion to be achieved for the halogenated analytes. The quantitation limit for carbon disulfide is 12 ppb. Two compounds found in drinking water were identified by GC/MS as bromodichloromethane and chlorodibromomethane. Drinking water from several cities was analyzed for these trihalomethanes as well as for bromoform. Levels of up to 17 ppb bromodichloromethane were found. Recoveries ranged from 96 to 103%.     

Quantitation of total folate in whole blood using LC-MS/MS

An accurate method for measuring whole blood total folate using liquid chromatography with tandem mass spectrometry is described and compared to GC/MS and a chemiluminescence assay. Whole blood from normal adults (n = 15) was fortified with a [(13)C(6)]para-aminobenzoic acid (pABA) internal standard and treated with 12.1 N hydrochloric acid at 110 degrees C for 4 h to hydrolyze all folates to pABA. Contaminants in the hydrolysate were adsorbed onto a C18 SPE cartridge. The eluate containing the folate catabolite pABA was partitioned into ethyl acetate and methylesterified with trimethylsilyldiazomethane. The methyl-pABA derivatives were quantified by positive-ion atmospheric pressure chemical ionization (APCI)LC-MS/MS. An isocratic mobile phase of acetonitrile-water (70:30) (v/v) on a C18 analytical column was used with a postcolumn reagent of 0.025% formic acid. The limit of quantitation for folate was 56.6 nmol/L RBC, and the limit of detection was 22.6 nmol/L RBC. Folate levels as determined by LC-MS/MS correlated well with the chemiluminescence assay and a GC/MS method. This new LC-MS/MS method provides enhanced sample throughput (n = 36 per day) as compared to GC/MS methods. LC-MS/MS will enable accurate measurements of red blood cell (RBC) folate in nutrition surveys and clinical trials.     

Gas chromatographic determination of electron capture sensitive volatile industrial chemical residues in foods, using AOAC pesticide multiresidue extraction and cleanup procedures

Electron capture (EC) gas chromatographic (GC) parameters have been developed for determining some of the more volatile industrial chemicals that can be determined by the AOAC multiresidue method for organochlorine and organophosphorus pesticides with modified GC operating conditions. Retention times relative to pentachlorobenzene are reported for 143 industrial chemicals, pesticides, and related compounds on OV-101 GC columns at 130 degrees C. Also reported for most of the compounds are recoveries from fortified samples carried through the AOAC extraction and cleanup procedures for fatty and/or nonfatty foods, Florisil elution characteristics, and GC relative retention times on mixed OV-101 + OV-210 columns at 130 degrees C. Our laboratory has used the modified EC/GC parameters with the AOAC multiresidue extraction/cleanup procedures to determine many volatile halogenated industrial chemical contaminants in foods, chiefly in samples of fresh-water fish. Other modifications of the AOAC method are described to improve the tentative identification and quantitative measurement of these volatile residues.     

Release of atrazine ((14)C) from two undisturbed submerged sediments over a two-year period.

Through water erosion and runoff, sediment-adsorbed atrazine can undergo sedimentation and accumulation at the bottom of water bodies and become potential sources of atrazine to the water column. The purpose of this study is to determine the fate and release of atrazine ((14)C) to the water column from two simulated undisturbed submerged sediments at two temperature treatments (5 and 24 degrees C) over a 2-year period. Atrazine residue ((14)C) was released from the two sediments and was, primarily, diffusing from the sediment pore water to the water columns. The amount released was affected by sediment type and is related to the sediment's adsorption/desorption capacity. Larger amounts of residue ((14)C) were released to the water columns at 5 degrees C than at 24 degrees C. Atrazine degraded in the shallow submerged anaerobic sediment's water columns over the 2-year period. Less than 2% (percent of applied in atrazine equivalent) of extractable atrazine and metabolites remained in the sediment after 2 years. The amount of nonextractable atrazine residue ((1)(4)C) was significantly higher in sediments at 24 degrees C than at 5 degrees C. In conclusion, atrazine accumulating in shallow undisturbed submerged sediments from nonpoint sources would most likely degrade and/or become nonextractable over time and would have a low probability of becoming a significant source to the water body. The conditions where accumulation and future release of atrazine have a greater potential to occur are under very cold temperatures with low adsorption capacity sediments.     

Purge and trap method for determination of fumigants in whole grains, milled grain products, and intermediate grain-based foods

A method developed for the determination of 1,2-dibromoethane in whole grains and grain-based products has been modified and expanded to include 8 other fumigants. Samples are stirred with water and purged with nitrogen for 0.5 h in a water bath at 100 degrees C. The fumigants are collected on a trap composed of Tenax TA and XAD-4 resin, eluted with hexane, and determined by gas chromatography (GC) using electron capture detection or Hall electrolytic conductivity detection. Flame photometric detection in the sulfur mode is used to determine carbon disulfide. Thick-film, wide-bore capillary columns were used exclusively in both the determination and confirmation of the halogenated fumigants. The higher levels of fumigants are also confirmed by full scan GC/mass spectrometry. Samples are analyzed for carbon disulfide, methylene chloride, chloroform, 1,2-dichloroethane, methyl chloroform, carbon tetrachloride, trichloroethylene, 1,2-dibromoethane, and tetrachloroethylene. A total of 25 whole grains, milled grain products, and intermediate grain-based foods analyzed by this method contained fumigant levels up to 51 ppm (carbon tetrachloride in wheat). Recoveries from fortified samples ranged from 82 to 104%. Chromatograms from this purge and trap method are clean, so that low parts per billion and sub-parts per billion levels can be quantitated for the halogenated analytes. The quantitation level for carbon disulfide is 12 ppb.     

Gas chromatographic determination of oxalic acid in foods

A new quantitative gas chromatographic (GC) method has been developed for the determination of oxalic acid in foods. Solid sample is extracted with water (soluble oxalic acid) or 2N hydrochloric acid (total oxalic acid) at room temperature. An aliquot of sample extract is evaporated to dryness, and the oxalic acid in the residue is methylated with 7% hydrochloric acid-methanol. The reaction mixture is extracted with chloroform, and dimethyl oxalate is quantitated by GC. Recovery of oxalic acid added to liquid samples averaged 100.6%; recoveries from extracts of solid samples were 96.2-99.5 and 97.2-100.1% for water and hydrochloric acid extractions, respectively. Results are shown for determination of oxalic acid in spinach and beverages. The technique is simple, rapid, and accurate, and small samples may be used. The limit of determination is 20 micrograms.     

Barrier and mechanical properties of milk protein-based edible films containing nutraceuticals

Calcium caseinate (CC) and whey protein isolate (WPI) films were prepared to contain 5 or 10% Gluconal Cal (GC), a mixture of calcium lactate and gluconate, or 0.1 or 0.2% alpha-tocopheryl acetate (VE), respectively. The pH and viscosity of film-forming solutions and the water vapor permeability and tensile property of the films were determined using standard procedures. CC and WPI films have the capabilities to carry high concentration of GC or VE, but some of the film functionality might be compromised. Adding VE to CC and WPI films increased film elongation at break, whereas incorporating 0.2% VE decreased WVP of CC films and tensile strength of both CC and WPI films. Incorporation of GC reduced the tensile strength of CC films (P < 0.05), with 10% GC decreasing both elongation at break and WVP (P < 0.05). These types of films may be used for wrapping or coating to enhance the nutritional value of foods. The concentration of GC and VE added to the films must be carefully selected to meet required water barrier and mechanical properties of the films depending on their specific applications.     

Supercritical fluid extraction of bioavailable amino acids from soils and their liquid chromatographic determination with fluorometric detection

A new procedure with supercritical CO2 modified with 0.5 mL of water and 0.75 mL of 0.1 M HCl in situ and 0.75 mL of water on-line at 15 MPa and 50 degrees C for 45 min was applied for the extraction of bioavailable amino acids from soil samples. Total extraction time was 60 min, but more favorable conditions are even possible for selected groups of amino acids. All analytes were trapped into 20 mL of methanol with satisfactory recovery (94-104%) and determined using high-performance liquid chromatography with fluorometric detection on a Zorbax Eclipse column (4.6 x 75 mm, 3.5 microm) with Na2HPO4 and acetonitrile/methanol/water as a mobile phase. Linear calibration curves were obtained (r > 0.999 except 0.99823 for Ile) with lower limits of detection (S/N = 3) in the range from 1.54 pg (Gly) to 13.5 pg (Cy2) or from 18.6 fmol (Ser) to 64.8 fmol (Lys). Validation and repeatability data are also given. Comparable results were obtained with a robust, commonly used extraction method (0.5 M ammonium acetate, 60 min in shaker, followed by filtration and lyophilization). Limiting values of artificial release of amino acids were also determined for each soil sample to eliminate any false results to ensure that all extracted amino acids originate from soil solution and exchangeable bound positions of soil samples.     

Sterol oxidation in ready-to-eat infant foods during storage

The effect of storage on sterol oxidation of ready-to-eat infant foods was evaluated. Two different liquid infant foods (honey or fruits flavors), prepared with milk and cereals, were stored for 0, 2, 4, 7 and 9 months at 25 degrees C. Sterol oxidation products (SOP) were isolated by cold saponification, purified by silica solid-phase extraction, and analyzed by gas chromatography (GC) and GC-mass spectrometry. beta-Sitosterol was the most representative sterol, followed by cholesterol and campesterol. No significant differences in the total and single SOP content (0.8-1 mg/kg of product) were observed with respect to storage time and type of sample; the main SOP found was 7-ketositosterol (<0.2 mg/kg of product). The extent of stigmasterol oxidation (2.9%) was higher than that of cholesterol (1.9%) and beta-sitosterol (1.4%). The type and quality of raw materials, as well as the processing conditions, seem to greatly influence SOP formation and accumulation in infant foods.     

Gas chromatographic/mass spectrometric determination of daminozide in high protein food products

A gas chromatographic/mass spectrometric (GC/MS) method for determining daminozide in high protein products has been developed. Daminozide is hydrolyzed in the presence of a strong base to form unsymmetrical dimethylhydrazine (UDMH) which is then distilled from the food matrix. A stable derivative is formed by reacting UDMH with salicyladehyde to form salicyaldehyde dimethylhydrazone. This derivative is separated and quantitated by GC/MS using selected ion monitoring (SIM) of key ions in the fragmentation pattern: m/z 164 (molecular ion of hydrazone) and m/z 120 (C7H6ON). An internal standard, 4-nitroanisole, is monitored at m/z 153 (molecular ion) and m/z 123 (C6H5O2N). The limit of detection is 0.01 ppm daminozide in a 50 g sample; however, because of variation at low levels, the limit of quantitation is 0.1 ppm. Recoveries are 90% or greater from peanuts and peanut butter spiked at the 0.1-2 ppm level. Reproducibility of the method depends on the food matrix and is 26% RSD in the worst case. Data are compared for the GC/MS method and the official EPA colorimetric procedure. Results showed a high bias in the colorimetric method, especially when roasted peanut products were analyzed.     

Methylation methods for the quantitative analysis of conjugated linoleic acid (CLA) isomers in various lipid samples

Precise methylation methods for various chemical forms of conjugated linoleic acid (CLA), which minimize the formation of t,t isomers and allylmethoxy derivatives (AMD) with the completion of methylation, were developed using a 50 mg lipid sample, 3 mL of 1.0 N H(2)SO(4)/methanol, and/or 3 mL of 20% tetramethylguanidine (TMG)/methanol solution(s). Free CLA (FCLA) was methylated with 1.0 N H(2)SO(4)/methanol (55 degrees C, 5 min). CLA esterified in safflower oil (CLA-SO) was methylated with 20% TMG/methanol (100 degrees C, 5 min), whereas CLA esterified in phospholipid (CLA-PL) was methylated with 20% TMG/methanol (100 degrees C, 10 min), followed by an additional reaction with 1.0 N H(2)SO(4)/methanol (55 degrees C, 5 min). Similarly, CLA esterified in egg yolk lipid (CLA-EYL) was methylated by base hydrolysis, followed by reaction with 1.0 N H(2)SO(4)/methanol (55 degrees C, 5 min). These results suggest that for the quantitative analysis of CLA in lipid samples by GC, proper methylation methods should be chosen on the basis of the chemical forms of CLA in samples.     

Determination of polysorbates in foods by colorimetry with confirmation by infrared spectrophotometry, thin-layer chromatography, and gas chromatography

A method is presented for the detection of polysorbates (PSs) in 8 kinds of processed foods by colorimetric and thin-layer chromatographic (TLC) techniques. The PSs are extracted from processed foods with a mixture of methylene chloride and ethanol by using an Extrelut column. The extract is further purified by using a silica gel column. The PS extract is complexed with cobalt-thiocyanate (Cothiocyanate) reagent and is determined spectrophotometrically at 620 nm. The recoveries and coefficients of variation for 8 kinds of processed foods fortified with 0.1% PS 80 were 67.9-94.6% and 4.0-11.3%, respectively. The detection limit of TLC corresponded to 50 mg PS 80/kg. PS identity was confirmed by infrared spectrophotometry of PS extract, and gas chromatography of fatty acids and thin layer chromatography of POE-sorbitan residues after saponification.