再生混凝土与锈蚀钢筋间的粘结性能试验研究

为了探究再生混凝土结构的耐久性能,对5组不同钢筋锈蚀率(0~9%)的再生混凝土梁式试件进行加载试验。分析不同钢筋锈蚀率对再生混凝土梁式试件的钢筋应变、局部粘结应力、粘结滑移和极限粘结应力的影响。结果表明：钢筋锈蚀率大于3%时试件底部开始有细微锈胀裂缝出现;锈蚀率越大,荷载作用下钢筋应变沿锚固位置的变化曲线越平缓;局部粘结应力沿锚固段呈现出双峰分布,峰值主要集中在加载端和自由端附近;加载端附近位置滑移现象最先发生,远离加载端滑移现象延后;随着钢筋锈蚀率的增大,极限粘结强度先增加后降低,极限荷载下的滑移值增大。     

冻融环境下钢筋与粉煤灰混凝土的粘结性能

通过对内贴应变片钢筋的直接拔出试验,分析冻融作用下粉煤灰掺量对钢筋与粉煤灰混凝土间粘结性能的影响,得出冻融循环作用对钢筋与粉煤灰混凝土之间粘结性能的影响规律。试验结果表明：钢筋与粉煤灰混凝土的粘结强度随粉煤灰掺量的增加而降低;当粉煤灰掺量一定时,随着冻融循环次数的增加,混凝土强度有所下降,钢筋与粉煤灰混凝土间极限粘结强度降低;当粉煤灰掺量较大,达到40%时,随冻融次数的增加,钢筋粉煤灰混凝土试件极限粘结强度的下降幅度明显减缓,极限粘结强度对应的滑移量增大。表明掺入较多粉煤灰可使试件的冻融损伤现象得到缓解,冻融环境下钢筋混凝土的粘结性能得到提高。     

冻融损伤对再生混凝土耐久性及与钢筋粘结性能分析

制作掺入引气剂和未掺入引气剂的100%粗骨料取代率的再生混凝土RC1和RC2两组试件以及掺入引气剂和未掺入引气剂的普通混凝土NC1和NC2两组试件,并分别对经过不同次数冻融循环试件的抗压强度、质量损失率、动弹性模量损失率进行研究。结果表明,冻融后各组试件的抗压强度、质量损失率及动弹性模量损失率均降低,对于添加引气剂的NC1和RC1两组试件损失较小,其中RC1组试件在200次冻融后抗压强度损失接近40%,质量损失率达0.5%,动弹性模量损失率38.5%。100%取代率并加入引气剂的ZRC组试件冻融后进行中心拨出实验,发生劈裂破坏和钢筋拔出破坏2种形式。再生粗骨料混凝土与钢筋的极限粘结应力均随冻融次数的增加而降低,200次冻融后极限粘结应力下降33.5,荷载滑移曲线既有上升段也有下降段。     

600 MPa高强钢筋与混凝土的粘结锚固性能试验研究

为研究600 MPa高强钢筋与混凝土粘结锚固性能,设计了72个棱柱体试件进行拉拔试验,对600 MPa高强钢筋粘结锚固的破坏形态及粘结应力分布进行分析,通过建立基本粘结滑移关系及位置函数,确定600 MPa高强钢筋在混凝土结构中的粘结滑移本构关系。采用一次二阶矩法进行可靠度分析,提出锚固长度设计建议。研究表明：600 MPa高强钢筋粘结锚固的破坏形态及粘结应力分布与普通钢筋类似且粘结锚固性能良好,《混凝土结构设计规范》（GB 50010—2010）基本锚固长度计算公式依然适用于600 MPa高强钢筋。     

油菜秸秆施用不同剂量腐熟剂腐熟与种稻效果分析

为了确定腐熟剂对油菜秸杆的腐熟效果及最佳经济用量,进行了不同剂量腐熟剂对油菜秸秆腐熟种稻效果试验,结果以施用30kg/hm2腐熟剂最佳.     

不同秸秆还田方式及施肥对小麦复种小油菜经济效益的影响

为了减少小麦秸秆焚烧、控制污染和提高田间留茬的利用效率,采用二因素随机区组设计,在甘肃河西绿洲灌区通过大田试验,研究了小麦留高茬收割后立茬、粉碎、焚烧3种秸秆还田方式及化肥减量施用（参照N 180 kg/hm2、P2O5 90 kg/hm2）对春小麦复种油菜经济效益的影响。结果表明,3种秸秆还田的措施与传统低茬收割比较,小麦、油菜的产量均有显著提高,其中小麦单产以麦茬粉碎还田处理最高,复种油菜单产以秸秆焚烧还田最高,总产值、劳动生产率以高施肥、麦茬粉碎还田的处理最高,分别达26752元/hm2和59.45元/工日,纯收益、土地净产率和产出投入比以麦茬焚烧还田、化肥减量15%的处理最高,分别达20346元/hm2、11346元/hm2和1.76。化肥减量15%时,各高留茬秸秆还田处理间作物产量和经济效益指标之间没有显著差异,证明在合理的秸秆还田措施保证条件下,化肥较当前高施肥水平降低15%在生产中是可行的。从提高经济效益、生态效益和保护环境的综合因素分析,在小麦复种油菜生产中推荐的方案是小麦留茬20~25 cm收割,旋耕粉碎还田后复种油菜。     

Finite Element Modeling of Stainless Steel Plates in Compression and Structural Behavior

The behavior of plate in compression plays a basic role in relevant research. There are significant differences between stainless steel and carbon steel plates in structural behavior. Analysis on the behavior of stainless steel plate in compression was presented. The development of FE models for analyzing stainless steel plates in compression was described based on the results of Rasmussen's test. And the strength curve was achieved by such advanced FE models with a high degree of accuracy. The explicit strength equations and design method were proposed for determining the local buckling strength of stainless plate and cold formed rectangular hollow section in compression. It is shown that the numerical simulation results achieved by using Quach model are accurate.     

Full-Scale Test and Analysis of Mechanical Behavior of Concrete Filled Steel Tubular Column Node in Space Truss Structure

To investigate mechanical behavior and seismic behavior of concrete filled steel tubular column node (CFSTCN) in space truss structure, both full-scale test and Finite Element Method (FEM) were employed. The test load was 1.6 times of design load and by incremental step loading. Meanwhile, stress and deformation in CFSTCN were observed to monitor bearing capacity of the node. The results show that steel tubular works in elastic state and a small part of concrete beyond of compressive stress limits; steel tube and concrete adhesive well. The hysteretic energy dissipation capacity and failure mode under cyclic loading were revealed by nonlinear FEM. weakest position and ultimate bearing capacity of the node were obtained from FEM results. The method of combining full-scale test and FEM can well reveal the mechanical behavior and the seismic behavior of the node.