Thin layer chromatographic determination of aflatoxins, ochratoxins, sterigmatocystin, zearalenone, citrinin, T-2 toxin, diacetoxyscirpenol, penicillic acid, patulin, and penitrem A.

A general method is described for determining 16 mycotoxins in mixed feeds and other food products used in the manufacture of these feedstuffs. The mycotoxins are extracted and cleaned up by extracting with solvents of different pH. Thin layer chromatography is used to separate the toxins; toxins are then quantitated by the limit detection method. The minimum detectable concentration of mycotoxins in various products is: aflatoxin B1 or G1, 4--5 micrograms/kg; ochratoxin A or ethyl ester A 140--145 micrograms/kg; citrinin 600--750 micrograms/kg; zearalenone, 410--500 micrograms/kg; sterigmatocystin, 140--145 micrograms/kg; diacetoxyscirpenol, 2400--2600 micrograms/kg; T-2 toxin, 800--950 micrograms/kg; patulin, 750--800 micrograms/kg; penitrem A 14,000--14,500 micrograms/kg; penicillic acid 3400--3650 micrograms/kg.     

Gas chromatographic screening method for T-2 toxin, diacetoxyscirpenol, deoxynivalenol, and related trichothecenes in feeds

A gas chromatographic method for screening trichothecene mycotoxins in feeds is described. Feed is extracted with acetonitrile-water, and the toxins are purified with charcoal-alumina-Celite, Florisil, and silica mini-columns. Deoxynivalenol (DON), nivalenol (NIV), diacetoxyscirpenol (DAS), T-2 toxin, and their fungal metabolites are hydrolyzed to their corresponding parent alcohols (DON, NIV, scirpentriol, or T-2 tetraol) by alkaline hydrolysis. After derivatization to their pentafluoropropionyl analogs, they are quantitated by capillary gas chromatography with electron capture detection. Identity can be confirmed and sensitivity can be increased by using negative chemical ionization mass spectrometry with no additional sample workup. Recoveries of DAS, DON, and T-2 toxin averaged, respectively, 80, 65, and 85% in corn; 84, 65, and 88% in soybeans; and 70, 57, and 96% in mixed feeds at concentrations ranging from 0.1 to 2.0 ppm. Recoveries of 15-monoacetoxyscirpenol (MAS), HT-2, NIV, and T-2 tetraol were 97, 97, 86, and 56%, respectively, in corn at a concentration of 0.25 ppm: A detection limit of 0.02 ppm in corn, soybeans, and mixed feeds, and 0.05 ppm in silages is estimated.     

Separation and purification of sulforaphane from broccoli seeds by solid phase extraction and preparative high-performance liquid chromatography

A novel, rapid, and economical method to isolate and purify natural sulforaphane from broccoli seeds is described. The procedure involves solvent extraction of autolyzed seed meal, followed by separation by solid phase extraction (SPE) and purification by preparative high-performance liquid chromatography (HPLC). The SPE method provides higher yield of sulforaphane from crude extracts compared to conventional liquid-liquid extraction. High purity and recovery of sulforaphane product can be obtained by preparative HPLC with a C 18 column and 30% methanol in water as the mobile phase. The purified compound was characterized by MS and (1)H and (13)C NMR. The techniques described here are useful tools in the preparative-scale isolation of sulforaphane in a fast, cost-effective, and waste-conscious manner.     

Development of analyses by high-performance liquid chromatography and liquid chromatography/tandem mass spectrometry of bilberry (Vaccinium myrtilus) anthocyanins in human plasma and urine

Anthocyanins are potent antioxidants that may possess chronic disease preventive properties. Here, rapid, reliable, and reproducible solid-phase extraction, high-performance liquid chromatography (HPLC), and mass spectrometry techniques are described for the isolation, separation, and identification of anthocyanins in human plasma and urine. Recoveries of cyanidin-3-glucoside (C3G) were 91% from water, 71% from plasma, and 81% from urine. Intra- and interday variations for C3G extraction were 9 and 9.1% in plasma and 7.1 and 9.1% in urine and were less than 15% for all anthocyanins from a standardized bilberry extract (mirtoselect). Analysis of mirtoselect by HPLC with UV detection produced spectra with 15 peaks compatible with anthocyanin components found in mirtoselect within a total run time of 15 min. Chromatographic analysis of human urine obtained after an oral dose of mirtoselect yielded 19 anthocyanin peaks. Mass spectrometric analysis employing multiple reaction monitoring suggests the presence of unchanged anthocyanins and anthocyanidin glucuronide metabolites.     

Sephadex LH-20 cleanup, high pressure liquid chromatographic assay, and fluorescence detection of zearalenone in animal feeds

A high pressure liquid chromatographic (HPLC) method is described to determine zearalenone in animal feeds at levels as low as 0.01 ppm. Samples are extracted with chloroform-ethanol and initially purified using a SEP-PAK silica cartridge, followed by column chromatography using Sephadex LH-20. Separation by normal phase HPLC is followed by fluorescence detection. Recoveries at levels of 1.0-0.01 ppm averaged greater than 90%. Confirmation included HPLC analysis of the sample and a zearalenone standard, using 3 different excitation wavelengths, and comparison of fluorescence responses obtained. The method was successfully applied to the analysis of 1 corn and 3 cornmeal samples. Zearalenone was detected in all 4 samples at levels of 0.379-19.2 ppm.     

Extraction and thin layer chromatography of aflatoxin B1 in mixed feeds

A method was developed for the determination of aflatoxin B1 in commercially prepared feeds. The method incorporates methylene chloride and citric acid solution extraction, cleanup on a small silica gel column, and thin layer chromatography for quantitation. Commercial turkey starter, catfish chow, medicated pig starter, broiler finisher, rabbit chow, horse feed, rat chow, and dog chow were investigated. The feeds were spiked with naturally contaminated corn at 4 different levels of aflatoxin B1 (16-130 microgram/kg). Three assays were run on each of the 32 combinations of feed and levels of aflatoxin. Mean recoveries were 85.9-92.8% at levels of 16.5, 32.9, 65.8, and 131.6 micrograms/kg. The relative standard deviation per assay was 18.6%. This method is more rapid and less involved than most previously published methods for mixed feeds.     

Rapid high pressure liquid chromatographic determination of aflatoxin M1 in milk and nonfat dry milk

A modification of the current revised AOAC method, 26.A10-26.A15, is described for the rapid analysis of aflatoxin M1 in milk and nonfat dry milk. The method incorporates chloroform extraction and eliminates the need for column chromatography by using liquid-liquid partition for sample extract cleanup. Quantitation is carried out by using fluorescence detection combined with high pressure liquid chromatography (HPLC) of aflatoxin M1 which has been converted to aflatoxin M2a with trifluoroacetic acid. The method has a detection limit of 0.014 micrograms/L (2 X signal/noise) for whole milk. For 6 samples of naturally contaminated nonfat dry and freeze-dried milk, the modified method gave an average result of 0.698 micrograms/L; the AOAC method gave an average result of 0.386 micrograms/L.     

Mycotoxins in grain dust: method for analysis of aflatoxins, ochratoxin A, zearalenone, vomitoxin, and secalonic acid D

A multimycotoxin method is presented to quantitate aflatoxins, ochratoxin A, zearalenone, secalonic acid D, and vomitoxin in grain dust. Dust spiked with these mycotoxins was extracted sequentially with methylene chloride followed by acetonitrile-water (86 + 14). Vomitoxin was recovered in the latter extract and all other mycotoxins were recovered in the methylene chloride. Aflatoxins and ochratoxin were quantitated by fluorescence measurement on silica thin layer chromatographic plates. The other mycotoxins were quantitated after cleanup by reverse phase liquid chromatography and ultraviolet detection. Recoveries from dust spiked in the parts per billion (ng/g) range were approximately 80% (SD = 15-29%) for all mycotoxins. Minimum detectable amounts ranged from less than 0.5 ng/g for aflatoxins to 20 ng/g for zearalenone.     

Screening and quantitation of ochratoxin A in corn, peanuts, beans, rice, and cassava

To answer the need for simple, economical, rapid methods for mycotoxins, a procedure for screening and quantitation of ochratoxin A was developed. A methanol-aqueous KCl extraction is used, followed by cleanup with clarifying agents and partition into chloroform. Part of the chloroform extract is used for screening and the other part for quantitation by thin layer chromatography (TLC). The screening procedure takes 40 min, using a silica gel/aluminum oxide minicolumn developed for this purpose. The limits of detection are 80 and 10 micrograms/kg, respectively, for minicolumn screening and TLC quantitation. Ammonium sulfate is efficient in cleaning samples of corn and cassava; cupric sulfate is better with peanuts, beans, and rice. Tests were conducted on triplicate spiked samples of yellow corn meal, raw peanuts, dried black beans, polished rice, and cassava flour at different levels (400, 200, 80, 40, and 10 micrograms/kg). Recoveries ranged from 86 to 160% and the coefficients of variation ranged from 0 to 26%.     

Use of the Mycosep multifunctional cleanup column for liquid chromatographic determination of aflatoxins in agricultural products.

A liquid chromatographic (LC) technique has been developed that uses the Mycosep multifunctional cleanup (MFC) column. MFC columns provide a rapid 1-step extract purification. They are designed to retain particular groups of compounds that may create interferences in analytical methods. At the same time, MFC columns allow compounds of interest to pass through. In the method presented, test samples are extracted in a blender with acetonitrile-water (9 + 1). A portion of the extract is forced through an MFC column designed especially for analysis of numerous mycotoxins. Analytical interferences are retained, while aflatoxins pass through the column. Aflatoxins B1 and G1 are converted to their hemiacetals by heating a mixture of purified extract and water-trifluoroacetic acid-acetic acid (7 + 2 + 1) at 65 degrees C for 8.5 min. An aliquot of this mixture is analyzed by isocratic LC with acetonitrile-water mobile phase and fluorescence detection. A detection limit of less than 0.5 ng/g for aflatoxin B1 was obtained. Average recoveries greater than 95% total aflatoxins (B1, B2, G1, and G2) and coefficients of variation of less than 3% were obtained. The method was successfully applied to the following commodities: corn, almonds, pista-chios, walnuts, peanuts, Brazil nuts, milo, rice, cottonseed, corn meal, corn gluten meal, fig paste, and mixed feeds.     

Determination of zearalenone in cornflakes and other corn-based foods by thin layer chromatography, high pressure liquid chromatography, and gas-liquid chromatography/high resolution mass spectrometry

A simple cleanup procedure based on pH adjustments was used to obtain extracts of corn foods. The method gave good recoveries of zearalenone determined by thin layer chromatography (TLC) and high pressure liquid chromatography (HPLC). As little as 5 ng zearalenone was detected by TLC, using Fast Violet B Salt as the spray reagent; the lower limit of detection in cornflakes was about 20 microgram/kg. With HPLC on Spherisorb silica (5 micrometer) and detection by fluorescence at an excitation maximum of 310 nm as little as 5 microgram zearalenone/kg cornflakes could be determined. While the TLC method was also applicable to corn chips, cornmeal, popcorn, and frozen corn, an interference was observed in HPLC of the latter 3 products. This interference was separated from zearalenone by adding a second HPLC analytical column (Spherisorb ODS). Gas-liquid chromatography coupled with mass spectrometric single ion monitoring at high resolution, although of limited availability, was shown to be the most sensitive and selective method for determining zearalenone in corn foods. The natural occurrence of zearalenone in a sample of cornflakes (13-20 microgram/kg) was demonstrated by all 3 detection procedures.     

Determination of N-methylcarbamate pesticides in liver by liquid chromatography

A liquid chromatographic (LC) method using a 2-step purification technique for the simultaneous determination of 10 carbamates in bovine, swine, and duck livers has been developed. Carbamates are extracted from liver samples with methylene chloride. After evaporation, the residues from the extract are dissolved in methylene chloride-cyclohexane (1 + 1) and cleaned up by gel permeation chromatography. The eluate containing carbamate residues is evaporated to dryness, reconstituted in methylene chloride, further purified by passing it through an aminopropyl Bond Elut extraction cartridge, and analyzed by liquid chromatography using post-column derivatization with orthophthalaldehyde and fluorescence detection. Excitation and emission are set at 340 and 418 nm, respectively. Liver samples for beef, pork, and duck were fortified with 5, 10, and 20 ppb of mixed carbamate standards. The average of 10 recoveries of 10 carbamates at all 3 levels of fortification was greater than 80% with coefficients of variation less than 17%.     

Combined use of supercritical fluid extraction, micellar electrokinetic chromatography, and reverse phase high performance liquid chromatography for the analysis of antioxidants from rosemary (Rosmarinus officinalis L.)

Antioxidants from rosemary were determined by the combined use of supercritical fluid extraction (SFE) prior to reverse-phase high-performance liquid chromatography (RP-HPLC) or micellar electrokinetic chromatography (MEKC). The separation of antioxidants found in the SFE fractions was achieved by using a new MEKC method and a published HPLC procedure, both with diode array detection. The characterization of the different antioxidants was further done by HPLC-mass spectrometry. Advantages and drawbacks of HPLC and MEKC for analyzing the antioxidants found in the different extracts are discussed. From the results it is concluded that HPLC renders higher peak area and is better in its reproducibility than MEKC; both techniques provide similar analysis time reproducibility. The main advantage of MEKC is its much higher separation speed, which is demonstrated to be useful for the quick adjustment of SFE conditions, allowing rosemary fractions of higher antioxidative power to be obtained quickly. Moreover, the possibilities of this approach for following the degradation of antioxidants are discussed.     

Determination of ethalfluralin in canola seed, meal, and refined oil by capillary gas chromatography with mass selective detection

Ethalfluralin is a herbicide that is effective for weed control on a wide variety of crops, including canola. A method is described for the determination of ethalfluralin residues in canola seed, meal, and refined oil. Residues are extracted from canola sample matrixes with acetonitrile. An aliquot of the extract is diluted with water and purified by C(18) solid-phase extraction prior to analysis by capillary gas chromatography with mass selective detection. For all three sample matrixes, the method has a validated limit of quantitation of 0.02 microg/g and a limit of detection of 0.006 microg/g. Recoveries averaged 96 +/- 7% for canola seed, 87 +/- 6% for canola meal, and 89 +/- 5% for refined oil. In a magnitude-of-residue study, canola seed from field plots that had been treated with ethalfluralin at one to three times the maximum label rate for weed control were found to contain no detectable residue of the herbicide.     

Liquid chromatography and fluorescence detection of vitamin A in animal feeds, finished feeds, and premixes

A simple liquid chromatographic method for vitamin A (retinol) in animal feeds is described. The feed is saponified, diluted to minimize interferences, and extracted into petroleum ether with a single step. The analysis is sensitive and specific with liquid chromatography and a fluorescence detector. The minimum level of detection is 15 ng/mL, which is equivalent to 10,000 units/lb vitamin A. The method includes a stable and reproducible standardization of vitamin A that is used to calibrate standard peak heights in terms of units retinol/mL. Guarantees of 10,000 units/lb up to premix levels can be analyzed with good recoveries and precision.     

Determination of polysorbates in foods by colorimetry with confirmation by infrared spectrophotometry, thin-layer chromatography, and gas chromatography

A method is presented for the detection of polysorbates (PSs) in 8 kinds of processed foods by colorimetric and thin-layer chromatographic (TLC) techniques. The PSs are extracted from processed foods with a mixture of methylene chloride and ethanol by using an Extrelut column. The extract is further purified by using a silica gel column. The PS extract is complexed with cobalt-thiocyanate (Cothiocyanate) reagent and is determined spectrophotometrically at 620 nm. The recoveries and coefficients of variation for 8 kinds of processed foods fortified with 0.1% PS 80 were 67.9-94.6% and 4.0-11.3%, respectively. The detection limit of TLC corresponded to 50 mg PS 80/kg. PS identity was confirmed by infrared spectrophotometry of PS extract, and gas chromatography of fatty acids and thin layer chromatography of POE-sorbitan residues after saponification.     

Rapid, economical method for determination of aflatoxin and ochratoxin in animal feedstuffs

A quantitative procedure widely used in European Economic Community (EEC) countries has been successfully scaled down to produce a rapid method for determination of aflatoxin B1 (and other aflatoxins) in animal feeds. Without modification, the method may be used for simultaneous ochratoxin A determination in simple feeds, but a slightly different extraction procedure is required for compound feeds. Validity of the method has been demonstrated by comparison with the full EEC procedure for aflatoxin B1 and the Nesheim method for ochratoxin A. Analyses may be completed within 2 h and there is a considerable savings in materials over the 2 reference methods. The procedure is also less hazardous because volumes of toxic extract are small, and the operator is exposed to minimum solvent vapor.     

Determination of ergosterol in cereals, mixed feed components, and mixed feeds by liquid chromatography

A sensitive, rapid, reproducible, and reliable liquid chromatographic (LC) method is described for determination of ergosterol in feedstuffs. The sample is saponified directly and the saponified mixture is extracted with n-hexane. Ergosterol is determined without further purification or cleanup steps by using a liquid chromatograph with a 250 X 4.6 mm column packed with LiChrosorb Si 60, 5 microns, and a high pressure column prefilter. The ultraviolet detector is set at 282 nm. The limit of detection was 0.1 ppm; recovery ranged between 96.7 and 102.2%. Diode array technology is used for identification and peak purity control. Under strong UV irradiation (254 nm) and oxygen or nitrogen atmosphere ergosterol was converted almost quantitatively to ergocalciferol. Under the described conditions of the method, ergosterol proved to be stable. Ergosterol was determined in cereals, mixed feeds (e.g., for swine and poultry), and their components of plant and animal origin. It was not found in carcass meal, meat-and-bone meal, citrus pulps, or molasses; only traces were detected in fish meal.     

High pressure liquid chromatographic determination of aflatoxins in corn.

A high pressure liquid chromatographic (HPLC) method is proposed for determining aflatoxins in corn. The sample is extracted with methanol-10% NaCl (4 + 1), pigments are precipitated with zinc acetate, and the extract is cleaned up on a small (2 g) silica gel column. Aflatoxins in the purified extract are resolved by normal phase HPLC on a microparticulate (10 micrometer) silica gel column with water-saturated chloroform-cyclohexane, acetonitrile solvent, and detected by fluorescence on a silica gel-packed flowcell. The method was compared with chloroform-water extraction of the official CB method on 15 samples of contaminated corn. In 5 of the 6 samples containing aflatoxins B1, B2, G1, and G2, methanol-10% NaCl extracted more aflatoxin than did cloroform-water, as measured both by HPLC and by thin layer chromatography. In samples containing only B1 and B2, the 2 extraction solvents were virtually equivalent. Agreement was good between HPLC and TLC for each extraction solvent. Average recovery of aflatoxins B1, B2, G1, and G2 added to yellow cornmeal at 3 levels was greater than 90%.     

Chemical confirmatory tests for ochratoxin A, citrinin, penicillic acid, sterigmatocystin, and zearalenone performed directly on thin layer chromatographic plates

Published tests have been improved and a new procedure is described for chemical confirmation of mycotoxins directly on thin layer plates. After extraction and preliminary cleanup chromatography with n-hexane or chloroform, the mycotoxins ochratoxin A, citrinin, penicillic acid, sterigmatocystin, and zearalenone were easily separated by thin layer chromatography (TLC) using toluene-ethyl acetate-90% formic acid (6 + 3 + 1) developing solvent. In chemical confirmatory methods, the developed chromatogram was exposed to vapors of pyridine, acetic anhydride, or a mixture, or the mycotoxins were over-spotted. With this treatment, ochratoxin A, citrinin, penicillic acid, and zearalenone were converted to new fluorescent compounds, and observed under 365 nm light after re-chromatography with the same developing solvent. Sterigmatocystin was confirmed chemically using TLC plates impregnated with 0.6N H2SO4 or 10% oxalic acid in methanol. The described procedures are satisfactory for confirming mycotoxins present in standards, artificially contaminated grain samples (barley, corn, oat, rye, and wheat), and extracts from both fungal cultures and naturally contaminated grain samples.