麦草化学机械浆过氧化氢漂白工艺优化的研究

探讨了过氧化氢(H2O2)漂白麦草化学机械浆的各种影响因素。优化后的工艺条件为:H2O26%(质量分数,下同),浆浓20%,MgSO40.05%,二乙烯三胺五乙酸(DTPA)0.3%,Na2SiO35.0%,NaOH3.5%,漂白温度80℃,漂白时间2.5h,白度可以达到53%(ISO),能够满足配抄普通文化用纸的要求。     

马尾松TMP漂白性能的研究

对马尾松热磨机械浆(TMP)进行了过氧化氢(H2O2)、甲脒亚磺酸盐(FAS)单段漂白以及H2O2-FAS两段漂白实验的研究。结果表明,H2O2漂白马尾松TMP较适宜的工艺条件为H2O2用量2.5%,NaOH用量1.3%,Na2SiO3用量2.5%,浆浓20%,温度80℃,时间60min;FAS漂白马尾松TMP较适宜的工艺条件为FAS用量2.5%,NaOH用量0.625%,浆浓15%,温度80℃,时间75min。H2O2、FAS单段漂白后纸浆白度分别为72.6%ISO和58.2%ISO,H2O2-FAS两段漂白后纸浆白度可达76.3%ISO。     

木聚糖酶预处理对麦草化学机械浆可漂性及白度的改善

探讨了以玉米芯片为碳源制备木聚糖酶及麦草化学机械浆经该木聚糖酶预处理后可漂性和白度的改善效果。结果表明，直接以玉米芯为底物、里氏木霉为菌种产酶效果较好，当底物浓度为18g/L时，木聚糖酶活力可达38．34IU／mL。木聚糖酶预处理有利于改善麦草化机浆的可漂性，促进其过氧化氢漂白，有提高漂白浆白度，降低漂剂消耗。研究表明，当经单段H2O2漂至相同白度时，木聚糖酶预处理后可节约50％的H2O2用量。若麦草CMP酶处理后采用高浓度两段过氧化氢漂白，即XP3P3漂序（H2O2总量为6％0时，白度可达60％（ISO）以上。     

麦草氧碱法纸浆压力/温度过氧化氢漂白

麦草氧碱法纸浆经压力/温度H2O2(Ppt)漂白时,纸浆的卡伯值随H2O2用量和氧压的提高而下降,卡伯值从17.3下降至2.38,下降幅度达86.2 %,表明Ppt漂白时,脱木质素效果明显.若采用氧脱木质素 -鳌合处理 -压力温度H2O2漂白(OQPpt)和氧脱木质素 -酸处理 -压力温度H2O2(OAPpt)漂程,当H2O2用量为原料质量的3 %～4 %时,均可将麦草氧碱纸浆漂至白度80 %(SBD,以下同)左右,而采用OAPpt漂白比OQPpt漂白的纸浆的白度高2.0 %左右,且聚合度达到1 038左右.     

三倍体毛白杨低硬度NaOH-AQ浆全无氯漂白的研究

通过实验探讨了三倍体毛白杨低硬度NaOH-AQ浆（卡伯值13．5，粘度851mL／g。白度37％，ISO）H2O2强化氧脱木质素（QOP）的工艺务件，在此基础上提出了QOP、QP全无氯漂白的漂序，此漂序可以把该纸浆漂至82．0％（ISO），粘度保持在716mL／g，漂后纸浆得率91．78％，而且该漂序可操作性强，是一种适合低硬度NaOH-AQ浆的全无氯漂白新工艺。     

三倍体毛白杨低硬度NaOH-AQ浆全无氯漂白的研究

通过实验探讨了三倍体毛白杨低硬度NaOH-AQ浆(卡伯值13.5,粘度851 mL/g,白度37%,ISO)H2O2强化氧脱木质素(QOP)的工艺条件,在此基础上提出了QOP、QP全无氯漂白的漂序,此漂序可以把该纸浆漂至82.0%(ISO),粘度保持在716 mL/g,漂后纸浆得率91.78%,而且该漂序可操作性强,是一种适合低硬度NaOH-AQ浆的全无氯漂白新工艺.     

漆酶-介体系统处理麦草化学浆全无氯漂白性能的研究

采用漆酶－介体系统对麦草化学浆进行预处理，研究了几种全无氯漂白（TCF漂白）[氧碱脱木质素配合两段过氧化氢漂白（OEPP），两段过氧化氢漂白（QPP）和过乙酸配合一段过氧化氢漂白(PaP)]对漆酶处理后纸浆漂白性能的作用，结果表明，麦草浆经过漆酶预处理后，白度上升了12．9个白度单位（%,ISO)，漆酶处理浆氧碱脱木质素配合过氧化氢漂白后比原浆在相同条件下漂白后白度高14个白度单位以上，经两段过氧化氢漂白后白度比原浆在相同条件下（过氧化氢用量4％）漂白后白度高18．3个白度单位，经过乙酸过氧化氢漂白后比原浆在相同条件下漂白后白度高8．1个白度单位。漆酶处理浆漂白后强度比原浆漂白后的低，但是其白度高，如漂至相同的白度可以节约大量漂剂，有利于改善浆的质量，降低漂白废水的污染负荷。     

桉树硫酸盐浆的漂白

桉木硫酸盐漂白浆的显著特点是松厚度好和不透明度高,适宜于制造各种印刷纸,书写纸和卫生用薄纸,手感柔软。是目前纸张生产者乐于接受的一个浆种。桉木硫酸盐未漂浆经氧脱木素卡伯值可降低45～50％。氯化纸浆中的有机氯比未经氧脱木素纸浆申的有机氯少一半。漂白废水中的有机卤物化(AOX)生成量很低。在氯和次氯酸盐漂白过程中能生成微量的二恶英(DIOXIN)、三氯甲烷。用二氧化氯取代氯气是目前减少此类有害物质生成的有效手段。现代化的漂白流程都包括有氧脱木素过程,在氯化段用高百分比二氧化氯代替氯气,碱抽提段在加热状态下加入少量氧气,可大大地减少后面漂白段的二氧化氯耗用量。桉木硫酸盐浆经氧脱木素后用C/D—E/0—D短流程的三段漂白可获得89％(ISO)白度的全漂白化学木浆。     

马尾松硫酸盐浆单段氧脱木质素最佳工艺条件的研究

研究了马尾松硫酸盐浆单段氧脱木质素的最佳工艺条件。结果表明 :氧压0 .6MPa、温度 10 0℃、时间 80min、NaOH用量 5%、MgSO4用量 0 .5%、浆浓 10 % ,在此条件下 ,纸浆木质素脱出率 4 7 1% ,氧脱木质素后纸浆粘度 94 8 1cm3/g ,白度 4 1 0 %(ISO) ,得率 96.9% ,经过氧脱木质素后浆的裂断长 6 3km ,耐破指数 5 8kPa·m2 /g ,撕裂指数 14 1mN .m2 /g     

硫酸盐苇浆电化学漂白的研究

用二氧化铅做阳极，不锈钢做阴极，铁氰化钾为催化剂，对硫酸盐苇浆进行电化学漂白，详细讨论了电流密度、温度、用碱量、漂白时间、催化剂用量以及纸浆浓度等因素对纸浆卡伯值和粘度的影响。通过综合分析得出硫酸盐苇浆电化学漂白的最佳条件是：用碱量0．4％、电流密度6．67mA／cm2、漂白时间30min、漂白温度80℃、催化剂浓度12．50mmol／L，浆浓1．3％。     

Browsing Damage on Pine (Pinus sylvestris and P. contorta) by a migrating moose (Alces alces) Population in Winter: Relation to Habitat Composition and Road Barriers

In Scandinavia, moose (Alces alces L.) sometimes cause severe browsing damage to economically-important pine. Moose-vehicle accidents have spurred construction of fences along roads, and these may interfere with moose migration between summer and winter ranges, or the road alone may be a barrier. If this happens and moose build up along roads, landowners may suffer economically. Therefore, this study investigated whether roads, fences or other factors influence the use of young pine stands by moose. Eighty stands along roads in northern Sweden were evaluated in which individually-browsed branches were counted on 9972 pines. Moose browsing was not significantly related to birch (Betula pendula Roth, B. pubescens Ehrh.) density, nor did it differ between pines (Pinus contorta Douglas or P. sylvestris L.). However, increased pine density, site productivity and proximity to a highway were associated with increased browsing. Further large-scale studies are needed to understand moose habitat selection and the effects of roads.     

Effects of Root Freezing on the Physiology and Growth of Picea glauca,Picea mariana and Pinus banksiana Seedlings Under Different Soil Moisture Regimes

The root systems of 2-yr-old Picea glauca, Picea mariana and Pinus banksiana seedlings were submitted to various frost temperatures during an artificial frost to induce different levels of root damage. Frost-damaged and control seedlings were placed in a greenhouse under high and low soil moisture regimes. Seedling growth and physiology were evaluated periodically. Seedling survival was reduced when root damage reached levels of 60-80%. Root systems of all three species showed partial to total recovery by the end of the experiment. In general, root freezing damage caused reductions in seedling growth, with these reductions becoming less significant over time. Root damage had little to no effect on black spruce and jack pine seedling physiology, while white spruce CO 2 uptake decreased with increasing root damage. Shoot nitrogen content of all three species decreased slightly with increasing root damage.     

Stand Structure in Pine,Spruce and Deciduous Forests: A Comparison Between Finnish and Russian Karelia

This study investigated the stand structure in pine, spruce and deciduous forests in the border district of Finland and Russia. A total of 46 mature forest stands was selected as pairs, the members of each pair being as similar as possible with respect to their forest site type, age, moisture and topography. The stands were then compared between the two countries by means of basal areas and number of stems. The proportions of dominating tree species were 2-12% lower, and correspondingly the proportions of secondary tree species higher, in Russian forests. The density of the forest stock was also higher in each forest type in Russia. The forests in the two countries differed most radically in terms of the abundance of dead trees. The amount was two to four times higher in Russian deciduous and spruce forests, and in pine forests the difference was 10-fold. The stand structures indicated that Russian coniferous stands, in particular, were more heterogeneous than intensively managed pine and spruce stands in Finland.     

Growth and Terminal Bud Formation in Picea abies Seedlings Grown with Alternating Diurnal Temperature and Different Light Qualities

The root collar diameter and the height:diameter ratio are of particular importance in container-grown seedlings where a high density in the containers may produce spindly seedlings. Temperature regimes and light quality are known to affect plant growth. The aim of this study was to identify responses in Picea abies (L.) Karst. seedlings grown with light providing different red:far-red ratios and under temperature regimes with alternating day (DT) and night temperature (NT) from negative (DT < NT) to positive (DT > NT) difference (DIF) between DT and NT. Experiments were conducted in controlled environment chambers and in a daylight phytotron. Only limited thermoperiodic responses appeared in P . abies seedlings with respect to seedling height and dry weight accumulation. The formation of terminal buds, however, was clearly delayed in seedlings grown at negative DIF. The results indicate a requirement for day extension light that is high in far-red, to prevent terminal bud formation under natural short-day conditions. An extended study should be conducted to clarify the minimum level of light intensity and the optimal light quality needed to prevent terminal bud formation under natural short-day conditions.     

CAD与建筑设计的关系

本文分析了CAD在设计中引起的正面和负面影响,并进行了系统的阐述,从而使设计者在应用中能够保持客观的态度。     

Natural Regeneration in Clear-cuts: Effects of Scarification,Slash Removal and Clear-cut Age

The effects of soil scarification (mounding), slash removal and clear-cut age on the natural regeneration in clear-cuts was evaluated using data from four sites in southern Sweden. The treatments were carried out during a good seed and establishment year for birch ( Betula pubescens Ehrh. and B. pendula Roth). Scarification had the strongest positive effect on the density of naturally regenerated seedlings, especially in birch, but also in pine ( Pinus sylvestris L.) and spruce [ Picea abies (L.) Karst]. Slash removal had a positive effect on birch density. No statistically significant effect of clear-cut age was found. In addition, no statistically significant interactions between clear-cut age and scarification or slash removal were found. The ingrowth of field vegetation was the fastest in areas that were not scarified, less rapid in areas scarified on old clear-cuts, and the slowest after scarification in fresh clear-cuts. In conclusion, it may be possible to control the density of birch during a good establishment year for birch. If birch is desired, the best combination of treatments is to remove the slash and scarify; otherwise, these treatments should be avoided.     

Risk Perception Among Non-industrial Private Forest Owners

Based on an enquiry, risk perception among non-industrial private forest owners is described in relation to climate change and forestry hazards. Of the respondents, 11% took action to remedy the effects of climate change. Out of a given set, hazards were ranked according to each respondent's experience of recent substantial financial loss to the estate and in relation to his or her willingness to make investments aimed at risk reduction. For each hazard, the respondent assessed the risk in four classes ranging from very high to negligible risk. Six hazards were considered most problematic in all three aspects: browsing damage, falling timber prices, damage by wind, spruce bark beetle, root rot and pine weevil. A majority of the respondents claimed to take action to reduce the risk associated with at least one hazard, while 35% did not know whether they did. Excluding climate change, the need for decision support was the largest in relation to damage by wind owing to a combination of perceived high risk and a high level of ignorance in relation to whether risk-reducing measures were taken.     

Interactions in decomposition and N mineralization between tropical legume residue components

In situ produced plant residues contain a mixture of different plant components of varying quality. To assess synergistic or antagonistic interactions occurring during the decomposition and mineralization of such mixtures, individual plant parts (stems, leaves, leaf litter and roots) or the mixture of stems, leaves and leaf litter of the agroforestry species pigeonpea (Cajanus cajan) or of crop residues of peanut (Arachis hypogaea) or of the weed hairy indigo (Indigofera hirsuta) were incubated in pots for 19 weeks. Periodically, remaining plant residues were sieved out (>2 mm), weighed and N content as well as soil mineral N determined. Above- and below-ground residues of peanut decomposed fastest and showed the largest N release in agreement with their high N concentration and low-acid detergent fibre (ADF) : N ratio. Hairy indigo was hypothesized to be of lower quality than pigeonpea because of its high-polyphenol content. However, it decomposed faster than pigeonpea, largely because of the higher N and lower lignin concentration of its components. Ranking of individual plant components for N mineralization resulted in the following pattern, leaves > leaf litter > roots > stems. In mixtures of the different plant components a similar species order in decomposition was obtained, e.g. peanut > hairy indigo > pigeonpea. The amount of N released from the mixture was dominated by stem material that comprised 46–61% of the mixture. The interactions in mixtures were relatively small for peanut (generally high-quality components) as well as for pigeonpea (low proportion of high-quality components, i.e. N rich leaf material). However, a positive interaction occurred during later stages of N mineralization in the mixture of hairy indigo as it had a significant proportion of N rich components and absence of highly reactive polyphenols. Thus, for plants with low to intermediate chemical quality attributes, manipulating plant composition (e.g. by varying harvest age, affecting stem and leaf proportions) will be important to obtain significant interactions during decomposition when its components are mixed.     

Pasture production and tree growth in a young pine plantation fertilized with inorganic fertilizers and milk sewage in northwestern Spain

The use of organic waste materials such as milk sewage as an organic fertilizer could have the dual advantages of organic-waste disposal and reduced dependence on inorganic fertilizers. The effects of fertilization with (1) conventional mineral fertilization, (2) milk sewage sludge at 40 kg N ha⁻¹ target rate and (3) no fertilization on pasture production and tree growth were examined in an experiment consisting of two pasture mixtures under a one-year-old Pinus radiata plantation with a density of 2500 trees ha⁻¹. The two pasture mixtures were: (1) Dactylis glomerata L. var. saborto (25 kg ha⁻¹) + Trifolium repens L. group Ladino (4 kg ha⁻¹) + Trifolium pratense L. var. Marino (1 kg ha⁻¹); (2) Lolium perenne L. var. Tove (25 kg ha⁻¹) + Trifolium repens L. group Ladino (4 kg ha⁻¹) + Trifolium pratense L. var. Marino (1 kg ha⁻¹). The experiment began in the spring of 1995 using a randomized block design with three replicates in Castro Riberas de Lea (Lugo, Galicia, north-western Spain). Plot size was 12 × 8 m², with a 1 m buffer strip between plots. Two-year data showed that fertilization with either material had a positive effect on pasture production, with no significant difference between the two fertilization treatments. Tree growth in the milk sewage sludge plot was significantly higher than in the control plots. Inorganic fertilization increased pasture production, but affected tree growth negatively. The results show that milk sewage sludge could be used as a fertilizer in silvo-pastoral systems. This revised version was published online in June 2006 with corrections to the Cover Date.