浅谈辊压法木材防护浸注技术

简述了国内外木材浸注技术的最新研究进展;重点论述了木材防护浸注厅法--辊压法,讨论了辊压法的浸注原理,以及与传统木材浸注方法--真空加压法在设备、工艺方面的比较,明确了控制压缩率的重要作用,并尝试应用计算机图像处理技术测量计算木材体积空隙率来确定压缩率,建议辊压浸注处理大青杨时,压缩率可试取50％及以下。     

辊压处理大青杨木材的密度和干缩系数变异

对大青杨辊压处理材(压缩率10%～50% )的密度和干缩系数进行测试和研究.结果表明,与素材相比,辊压处理材的全干、气干和基本密度均有所增加,密度变化率＜5%,其中气干密度增幅最大,密度变异与压缩方向无明显相关;气干和全干干缩系数随压缩率增大而变大,变动范围-3.448%～23.678%;弦向干缩系数变化大于径向.     

平压浸注填充PF树脂工艺对杨木增重率的影响研究

为探讨浸注工艺对木材增重率的影响,以PF树脂为浸注材料,以树脂浓度、压缩次数、保压时间、浸渍时间和压缩率为试验因素,采用单因素试验方法在平压浸注装置上对杨木试件进行了浸注填充。结果显示:2次压缩较1次压缩,杨木木材增重率增加了20. 2%;保压时间从0 min延长至10 min,杨木木材增重率增加了11. 5%;浸渍时间从1 h延长至2 h,杨木木材增重率提高了8. 8%;再增加压缩次数、延长保压时间和浸渍时间,杨木木材增重率均变化不大;而杨木木材增重率随PF树脂浓度和杨木木材压缩率增加呈线性增加,PF树脂浓度与压缩率对杨木木材增重率具有显著影响。因此选择压缩次数为2次,保压时间为10 min,浸渍时间为1 h,PF树脂浓度与杨木木材压缩率由改性木材的用途决定。     

杨（桦）木单板树脂浸渍调控系统的开发设计

利用广义神经网络建立了树脂浸渍模型,该模型可实现常压浸渍和辊压浸渍中树种、单板纹理、单板,厚度。树脂固体含量、浸渍时间或辊筒间隙等几方面因素与单板增重率之间的高精度映射,从而进行树脂浸渍量的实时调控。模型相关系数均大于93％,平均相对误差均小于10．2％。     

压缩率对杉木浸注的影响

在5%～40%压缩率范围内的8种条件下,进行杉木压缩处理,分析处理材的渗透性与浸注性能。结果表明:1)压缩杉木的浸注量随着压缩率增大而增大,压力释放即时完成70%以上的浸注量,此后达到最大浸注量的时间,随着压缩率的增大而增加;2)压缩处理能有效改善杉木的渗透性,但压缩率对渗透性影响不显著;3)压缩处理杉木浸注性能的改善,是渗透性提高和可浸注空间增大的共同作用。在工业化生产中,可以通过压缩率来控制浸注量。     

辊压浸注浸渍树脂致木材力学性质变异

使用脲醛和酚醛两种浸渍树脂对大青杨板材实施辊压浸注处理,对不同工艺条件处理材的增重率和主要力学性能指标进行了测试和分析。结果表明:增重率随着树脂质量分数、辊压压缩率和压缩次数的增加而增大,浸注脲醛树脂的增重率在0.85%~12.92%之间,浸注酚醛树脂的增重率在2.01%~15.16%之间。与未处理材相比,辊压浸注脲醛树脂处理材的硬度提高了1.63%~11.32%,耐磨性提高了3.80%~21.77%,抗弯强度提高了5.16%~19.08%,抗弯弹性模量提高了4.20%~15.65%,冲击韧性提高了2.66%~15.50%;浸注酚醛树脂处理材以上五种指标依次提高了4.21%~11.89%、3.11%~23.17%、7.60%~19.85%、6.46%~16.32%和4.81%~14.78%。     

树脂增强桦木单板重组材的性能研究

采用三聚氰胺甲醛树脂辊压浸注桦木单板,通过热压定型得到树脂增强重组材.探讨不同树脂固体含量、辊压压榨率和热压压力对板材吸水厚度膨胀率、静曲强度、顺纹抗拉强度、胶合强度等性能的影响.结果表明,树脂固体含量50%、辊压压榨率20%、热压压力2.0 MPa时,重组材的物理力学性能指标综合水平较佳.     

加压因素对杨木单板压缩率和回弹率的影响

以速生杨木的边/心材单板为研究对象,对其进行水热密实化处理,通过单因素试验方法,分别研究了加压温度和加压压力对杨木边/心材单板的压缩率、气干24和48 h的厚度回弹率的影响,初步探讨了各个因素的作用机理.研究发现:各因素水平下,杨木边/心材单板的压缩率和厚度回弹率均呈现出一定的规律性,心材单板的压缩率高于边材单板,但厚度回弹率低于边材单板,且各因素的作用机理有所差异.边/心材单板水热密实化处理的较佳条件均为:加压温度150℃,加压压力5 MPa.     

水热密实化工艺对杨木单板性能的影响北大核心

以速生杨木边/心材单板为研究对象,对其进行水热密实化处理,通过单因素试验,分别研究热压时间、单板含水率两个因素的改变对杨木边/心材单板的压缩率、气干24h和148h的厚度回弹率的影响,初步探讨了各因素的作用机理。研究结果表明:单板的压缩率和厚度回弹率均随因素水平的改变而呈现出明显的规律性,心材单板的压缩率高于边材单板,但厚度回弹率低于边材单板,各因素的作用机理有所差异,单板水热密实化处理的优化工艺条件:热压时间8min,含水率20%,热压温度1.50℃,热压压力5MPa。     

水热密实化工艺对杨木单板性能的影响

以速生杨木边/心材单板为研究对象,对其进行水热密实化处理,通过单因素试验,分别研究热压时间、单板含水率两个因素的改变对杨木边/心材单板的压缩率、气干24h和148h的厚度回弹率的影响,初步探讨了各因素的作用机理。研究结果表明:单板的压缩率和厚度回弹率均随因素水平的改变而呈现出明显的规律性,心材单板的压缩率高于边材单板,但厚度回弹率低于边材单板,各因素的作用机理有所差异,单板水热密实化处理的优化工艺条件:热压时间8min,含水率20%,热压温度1.50℃,热压压力5MPa。     

Browsing Damage on Pine (Pinus sylvestris and P. contorta) by a migrating moose (Alces alces) Population in Winter: Relation to Habitat Composition and Road Barriers

In Scandinavia, moose (Alces alces L.) sometimes cause severe browsing damage to economically-important pine. Moose-vehicle accidents have spurred construction of fences along roads, and these may interfere with moose migration between summer and winter ranges, or the road alone may be a barrier. If this happens and moose build up along roads, landowners may suffer economically. Therefore, this study investigated whether roads, fences or other factors influence the use of young pine stands by moose. Eighty stands along roads in northern Sweden were evaluated in which individually-browsed branches were counted on 9972 pines. Moose browsing was not significantly related to birch (Betula pendula Roth, B. pubescens Ehrh.) density, nor did it differ between pines (Pinus contorta Douglas or P. sylvestris L.). However, increased pine density, site productivity and proximity to a highway were associated with increased browsing. Further large-scale studies are needed to understand moose habitat selection and the effects of roads.     

Effects of Root Freezing on the Physiology and Growth of Picea glauca,Picea mariana and Pinus banksiana Seedlings Under Different Soil Moisture Regimes

The root systems of 2-yr-old Picea glauca, Picea mariana and Pinus banksiana seedlings were submitted to various frost temperatures during an artificial frost to induce different levels of root damage. Frost-damaged and control seedlings were placed in a greenhouse under high and low soil moisture regimes. Seedling growth and physiology were evaluated periodically. Seedling survival was reduced when root damage reached levels of 60-80%. Root systems of all three species showed partial to total recovery by the end of the experiment. In general, root freezing damage caused reductions in seedling growth, with these reductions becoming less significant over time. Root damage had little to no effect on black spruce and jack pine seedling physiology, while white spruce CO 2 uptake decreased with increasing root damage. Shoot nitrogen content of all three species decreased slightly with increasing root damage.     

Stand Structure in Pine,Spruce and Deciduous Forests: A Comparison Between Finnish and Russian Karelia

This study investigated the stand structure in pine, spruce and deciduous forests in the border district of Finland and Russia. A total of 46 mature forest stands was selected as pairs, the members of each pair being as similar as possible with respect to their forest site type, age, moisture and topography. The stands were then compared between the two countries by means of basal areas and number of stems. The proportions of dominating tree species were 2-12% lower, and correspondingly the proportions of secondary tree species higher, in Russian forests. The density of the forest stock was also higher in each forest type in Russia. The forests in the two countries differed most radically in terms of the abundance of dead trees. The amount was two to four times higher in Russian deciduous and spruce forests, and in pine forests the difference was 10-fold. The stand structures indicated that Russian coniferous stands, in particular, were more heterogeneous than intensively managed pine and spruce stands in Finland.     

Growth and Terminal Bud Formation in Picea abies Seedlings Grown with Alternating Diurnal Temperature and Different Light Qualities

The root collar diameter and the height:diameter ratio are of particular importance in container-grown seedlings where a high density in the containers may produce spindly seedlings. Temperature regimes and light quality are known to affect plant growth. The aim of this study was to identify responses in Picea abies (L.) Karst. seedlings grown with light providing different red:far-red ratios and under temperature regimes with alternating day (DT) and night temperature (NT) from negative (DT < NT) to positive (DT > NT) difference (DIF) between DT and NT. Experiments were conducted in controlled environment chambers and in a daylight phytotron. Only limited thermoperiodic responses appeared in P . abies seedlings with respect to seedling height and dry weight accumulation. The formation of terminal buds, however, was clearly delayed in seedlings grown at negative DIF. The results indicate a requirement for day extension light that is high in far-red, to prevent terminal bud formation under natural short-day conditions. An extended study should be conducted to clarify the minimum level of light intensity and the optimal light quality needed to prevent terminal bud formation under natural short-day conditions.     

CAD与建筑设计的关系

本文分析了CAD在设计中引起的正面和负面影响,并进行了系统的阐述,从而使设计者在应用中能够保持客观的态度。     

Natural Regeneration in Clear-cuts: Effects of Scarification,Slash Removal and Clear-cut Age

The effects of soil scarification (mounding), slash removal and clear-cut age on the natural regeneration in clear-cuts was evaluated using data from four sites in southern Sweden. The treatments were carried out during a good seed and establishment year for birch ( Betula pubescens Ehrh. and B. pendula Roth). Scarification had the strongest positive effect on the density of naturally regenerated seedlings, especially in birch, but also in pine ( Pinus sylvestris L.) and spruce [ Picea abies (L.) Karst]. Slash removal had a positive effect on birch density. No statistically significant effect of clear-cut age was found. In addition, no statistically significant interactions between clear-cut age and scarification or slash removal were found. The ingrowth of field vegetation was the fastest in areas that were not scarified, less rapid in areas scarified on old clear-cuts, and the slowest after scarification in fresh clear-cuts. In conclusion, it may be possible to control the density of birch during a good establishment year for birch. If birch is desired, the best combination of treatments is to remove the slash and scarify; otherwise, these treatments should be avoided.     

Risk Perception Among Non-industrial Private Forest Owners

Based on an enquiry, risk perception among non-industrial private forest owners is described in relation to climate change and forestry hazards. Of the respondents, 11% took action to remedy the effects of climate change. Out of a given set, hazards were ranked according to each respondent's experience of recent substantial financial loss to the estate and in relation to his or her willingness to make investments aimed at risk reduction. For each hazard, the respondent assessed the risk in four classes ranging from very high to negligible risk. Six hazards were considered most problematic in all three aspects: browsing damage, falling timber prices, damage by wind, spruce bark beetle, root rot and pine weevil. A majority of the respondents claimed to take action to reduce the risk associated with at least one hazard, while 35% did not know whether they did. Excluding climate change, the need for decision support was the largest in relation to damage by wind owing to a combination of perceived high risk and a high level of ignorance in relation to whether risk-reducing measures were taken.     

Interactions in decomposition and N mineralization between tropical legume residue components

In situ produced plant residues contain a mixture of different plant components of varying quality. To assess synergistic or antagonistic interactions occurring during the decomposition and mineralization of such mixtures, individual plant parts (stems, leaves, leaf litter and roots) or the mixture of stems, leaves and leaf litter of the agroforestry species pigeonpea (Cajanus cajan) or of crop residues of peanut (Arachis hypogaea) or of the weed hairy indigo (Indigofera hirsuta) were incubated in pots for 19 weeks. Periodically, remaining plant residues were sieved out (>2 mm), weighed and N content as well as soil mineral N determined. Above- and below-ground residues of peanut decomposed fastest and showed the largest N release in agreement with their high N concentration and low-acid detergent fibre (ADF) : N ratio. Hairy indigo was hypothesized to be of lower quality than pigeonpea because of its high-polyphenol content. However, it decomposed faster than pigeonpea, largely because of the higher N and lower lignin concentration of its components. Ranking of individual plant components for N mineralization resulted in the following pattern, leaves > leaf litter > roots > stems. In mixtures of the different plant components a similar species order in decomposition was obtained, e.g. peanut > hairy indigo > pigeonpea. The amount of N released from the mixture was dominated by stem material that comprised 46–61% of the mixture. The interactions in mixtures were relatively small for peanut (generally high-quality components) as well as for pigeonpea (low proportion of high-quality components, i.e. N rich leaf material). However, a positive interaction occurred during later stages of N mineralization in the mixture of hairy indigo as it had a significant proportion of N rich components and absence of highly reactive polyphenols. Thus, for plants with low to intermediate chemical quality attributes, manipulating plant composition (e.g. by varying harvest age, affecting stem and leaf proportions) will be important to obtain significant interactions during decomposition when its components are mixed.     

Pasture production and tree growth in a young pine plantation fertilized with inorganic fertilizers and milk sewage in northwestern Spain

The use of organic waste materials such as milk sewage as an organic fertilizer could have the dual advantages of organic-waste disposal and reduced dependence on inorganic fertilizers. The effects of fertilization with (1) conventional mineral fertilization, (2) milk sewage sludge at 40 kg N ha⁻¹ target rate and (3) no fertilization on pasture production and tree growth were examined in an experiment consisting of two pasture mixtures under a one-year-old Pinus radiata plantation with a density of 2500 trees ha⁻¹. The two pasture mixtures were: (1) Dactylis glomerata L. var. saborto (25 kg ha⁻¹) + Trifolium repens L. group Ladino (4 kg ha⁻¹) + Trifolium pratense L. var. Marino (1 kg ha⁻¹); (2) Lolium perenne L. var. Tove (25 kg ha⁻¹) + Trifolium repens L. group Ladino (4 kg ha⁻¹) + Trifolium pratense L. var. Marino (1 kg ha⁻¹). The experiment began in the spring of 1995 using a randomized block design with three replicates in Castro Riberas de Lea (Lugo, Galicia, north-western Spain). Plot size was 12 × 8 m², with a 1 m buffer strip between plots. Two-year data showed that fertilization with either material had a positive effect on pasture production, with no significant difference between the two fertilization treatments. Tree growth in the milk sewage sludge plot was significantly higher than in the control plots. Inorganic fertilization increased pasture production, but affected tree growth negatively. The results show that milk sewage sludge could be used as a fertilizer in silvo-pastoral systems. This revised version was published online in June 2006 with corrections to the Cover Date.