Fluorimetric determination of aflatoxin M1 in cheese

A simple and sensitive method is proposed for the determination of aflatoxin M1 in cheese. The ground cheese sample is extracted with acetone-water (3 + 1). Acetone is evaporated under vacuum, and the aqueous phase is passed through a C18 disposable cartridge. After the cartridge is washed with acetonitrile-water (1 + 9), the toxin is eluted with acetonitrile. The extract is then cleaned up on a silica cartridge. Final analysis is performed by 2-dimensional thin layer chromatography (TLC) combined with fluorodensitometry or by liquid chromatography on a reverse phase C18 column with fluorescence detection. Recovery is greater than 90%, and the coefficient of variation is 6% or less. The detection limit is in the range of 10 ng/kg. The identity of aflatoxin M1 is confirmed by formation of the M2a or acetyl-M1 derivative and rechromatography.     

Rapid quantitation and confirmation of aflatoxins in corn and peanut butter, using a disposable silica gel column, thin layer chromatography, and gas chromatography/mass spectrometry

A simple, rapid, and solvent-efficient method for determining aflatoxins in corn and peanut butter is described. Aflatoxins B1, B2, G1, and G2 were extracted from 50 g sample with 200 mL methanol-water (85 + 15). A portion of the extract was diluted with 10% NaCl solution to a final concentration of 50% methanol, and then defatted with hexane. The aflatoxins were partitioned into chloroform. The chloroform solution was evaporated, and the residue was placed on a 0.5 g disposable silica gel column. The column was washed with 3 mL each of hexane, ethyl ether, and methylene chloride. Aflatoxins were eluted with 6 mL chloroform-acetone (9 + 1). The solvent was removed by evaporation on a steam bath, and the aflatoxins were determined using thin layer chromatography (TLC) with silica gel plates and a chloroform-acetone (9 + 1) developing solvent. Overall average recovery of aflatoxin B1 from corn was 82%, and the limit of determination was 2 ng/g. For mass spectrometric (MS) confirmation, aflatoxin B1 in the extract from 3 g sample (20 ng/g) was purified by TLC and applied by direct on-column injection at 40 degrees C into a 6 m fused silica capillary gas chromatographic column. The column was connected directly to the ion source. After injection, the temperature was rapidly raised to 250 degrees C, and the purified extract was analyzed by negative ion chemical ionization MS.     

Liquid chromatographic determination of aflatoxin M1 in milk

The official AOAC method for aflatoxin M1 in milk was modified by replacing cellulose column chromatography with cartridge chromatographic cleanup and replacing thin layer chromatographic (TLC) determination with liquid chromatographic (LC) quantitation to yield a new method for bovine and porcine milk. An acetone extract of milk is treated with lead acetate and defatted with hexane, and M1 is partitioned into chloroform as in the AOAC method. Chloroform is removed by evaporation under a stream of nitrogen at 50 degrees C. The residue is dissolved in chloroform, the vessel is rinsed with hexane, and the 2 solutions are applied in sequence to a hexane-activated silica Sep-Pak cartridge. Less polar impurities are removed with hexane-ethyl ether, and M1 is eluted with chloroform-methanol, and determined by C18 reverse phase LC using fluorescence detection. Recoveries of M1 added to bovine milk at 0.25, 0.50, and 1.0 ng/mL were 90.8, 93.4, and 94.1%, respectively. The limit of detection was less than 0.1 ng M1/mL for both bovine and porcine milk.     

Comparison of an ELISA-based screening test with liquid chromatography for the determination of aflatoxins in corn.

An enzyme-linked immunosorbent assay (ELISA) screening test (CITE PROBE) was compared to liquid chromatography (LC) for the determination of aflatoxins in naturally contaminated corn samples. The CITE PROBE, with a positive/negative cutoff of 5 ng/g aflatoxin B1, was correct (based on LC results) on 47 of 51 samples. Two of the incorrect responses by the CITE PROBE were false positives on samples containing 4.4 ng/g and 4.1 ng/g aflatoxins by LC. Another incorrect response was a false negative on a sample containing 5.5 ng/g aflatoxins by LC. The fourth incorrect response was a false positive on a sample containing 1.9 ng/g aflatoxins by LC. On the basis of these results, the CITE PROBE was determined to be a reliable screening method for the detection of greater than or equal to 5 ng/g aflatoxins in corn.     

Thin layer chromatographic determination of aflatoxin in corn dust

Methods adopted by the AOAC and the American Association of Cereal Chemists for determining aflatoxin in corn were modified, and techniques were developed for application to samples of less than 1 to 10 g instead of the specified 50 g samples. Analysis included chloroform extraction of dust samples or dust collected from glass fiber filters, purification of extracts on a silica gel column of appropriate size, and measurement of aflatoxin by either 1- or 2-dimensional thin layer chromatography (TLC). The solvent for 1-dimensional TLC was chloroform-acetone-water (91 + 9 + 1). Solvents for 2-dimensional TLC were, first direction, ether-methanol-water (95 + 4 + 1, lined tank) and second direction, chloroform-acetone-water (91 + 9 + 1, unlined tank), or first direction, chloroform-acetone-water (91 + 9 + 1, unlined tank) and second direction, toluene-ethyl acetate-formic acid (60 + 30 + 10, unlined tank). When samples weighed less than or equal to 0.1 g, the entire concentrated extract was applied to the TLC plate. About 0.5-1.0 ng aflatoxin B1 could be detected on the plate, making the limit of detection about 9 ng/g for 0.1 g samples.     

Simple, rapid cleanup method for analysis of aflatoxins and comparison with various methods

A method is described for simple and rapid determination of aflatoxins in corn, buckwheat, peanuts, and cheese. Aflatoxins were extracted with chloroform-water and were purified by a Florisil column chromatographic procedure. Column eluates were concentrated and spotted on a high performance thin layer chromatographic (HPTLC) plate, which was then developed in chloroform-acetone (9 + 1) and/or ether-methanol-water (94 + 4.5 + 1.5) or chloroform-isopropanol-acetone (85 + 5 + 10). Each aflatoxin was quantitated by densitometry. The minimum detectable aflatoxin concentrations (micrograms/kg) in various test materials were 0.2, B1; 0.1, B2; 0.2, G1; 0.1, G2; and 0.1, M1. Recoveries of the aflatoxins added to corn, peanut, and cheese samples at 10-30 micrograms/kg were greater than 69% (aflatoxin G2) and averaged 91%, B1; 89%, B2; 91%, G1; 78%, G2; and 92%, M1. The simple method described was compared with the AOAC CB method, AOAC BF method, and AOAC milk and cheese method. These methods were applied to corn, peanut, and cheese composites spiked with known amounts of aflatoxins, and to naturally contaminated buckwheat and cheese. Recoveries were much lower for the BF method compared with our simple method and the CB method.     

Determination of aflatoxin M1 in milk by liquid chromatography with fluorescence detection

A liquid chromatographic (LC) method is proposed for the determination of aflatoxin M1 in milk. The method was successfully applied to both liquid whole and skim milk and also whole and skim milk powder. The samples are initially extracted with acetonitrile-water followed by purification using a silica gel cartridge and a C18 cartridge. Final analysis by LC was achieved using a radial compression module equipped with a 5 micron C18 column and a fluorescence detector. The method was successfully applied to samples at levels of 10 to 0.08 ppb added aflatoxin M1 with recoveries in the range of 70-98%.     

Development and application of solvent-free extraction for the detection of aflatoxin M1 in dairy products by enzyme immunoassay

The official methods for the quantification of aflatoxin M1 in dairy products (cheese and yogurt) include extraction into dichloromethane or chloroform, evaporation of the solvent, partitioning of the reconstituted residue with hexane, and subsequent analysis. To secure a rapid and inexpensive screen for aflatoxin M1 contamination, a sensitive competitive ELISA, using a rabbit polyclonal antibody, was developed for measuring aflatoxin M1 in milk and used in a comparative study for measuring the extraction efficiency of aflatoxin M1 in aqueous or organic solvent buffers using yogurt samples. An aqueous sodium citrate solution was found to be suitable for extracting aflatoxin M1, thus eliminating the need for organic solvents. The citrate extraction proved to be efficient (recovery ranged from 70 to 124%) in fortified samples of very different kinds of dairy products, including yogurt and six types of cheese. Fourteen yogurt and cheese samples were extracted with citrate solution and analyzed by ELISA. A good correlation was observed (y=0.95x-0.59, r2=0.98) when the data were compared with those obtained through the official method, across a wide range of aflatoxin M1 contaminations (10-200 ng/kg).     

Liquid chromatographic method for determination of aflatoxins B1, B2, G1, and G2 in corn and peanut products: collaborative study

A collaborative study of a liquid chromatographic method for the determination of aflatoxins B1, B2, G1, and G2 was conducted in laboratories located in the United States, Canada, South Africa, and Switzerland. Twenty-one artificially contaminated raw peanuts, peanut butter, and corn samples containing varying amounts of aflatoxins B1, B2, G1, and G2 were distributed to participating laboratories. The test portion was extracted with methanol-0.1N HCl (4 + 1), filtered, defatted with hexane, and then partitioned with methylene chloride. The concentrated extract was passed through a silica gel column. Aflatoxins B1 and G1 were derivatized with trifluoroacetic acid, and the individual aflatoxins were determined by reverse-phase liquid chromatography with fluorescence detection. Statistical analysis of the data was performed to determine or confirm outliers, and to compute repeatability and reproducibility of the method. For corn, relative standard deviations for repeatability (RSDr) for aflatoxin B1 ranged from 27.2 to 8.3% for contamination levels from 5 through 50 ng/g. For raw peanuts and peanut butter, RSDr values for aflatoxin B1 were 35.0 to 41.2% and 11.2 to 19.1%, respectively, for contamination levels from 5 through 25 ng/g. RSDr values for aflatoxins B2, G1, and G2 were similar. Relative standard deviations for reproducibility (RSDr) for aflatoxin B1 ranged from 15.8 to 38.4%, 24.4 to 33.4%, and 43.9 to 54.0% for corn, peanut butter, and raw peanuts, respectively. The method has been adopted official first action for the determination of aflatoxins B1, B2, G1, and G2 in peanut butter and corn at concentrations greater than or equal to 13 ng total aflatoxins/g.     

Improved method for confirmation of identity of aflatoxins B1 and M1 in dairy products and animal tissue extracts

A method is described for confirming the identity of aflatoxins B1 and M1 in dairy products and liver extracts on a thin layer plate. Extracts and standards containing aflatoxins B1 and M1 are spotted on 10 x 10 cm plates, which are developed 2-dimensionally in mixtures of isopropanol-acetone-chloroform. After the first development, trifluoroacetic acid-hexane (1 + 4) is sprayed on that part of the plate containing the separated extract components and the underdeveloped standard spots of B1 and M1, and the plate is heated 6-8 min at 75 degrees C. Then the plate is developed in a second direction, and the reaction products of B1 and M1 with trifluoroacetic acid from the extract are compared with the same derivatives of the respective standards. The method has been used successfully on extracts of milk, cheese, and liver containing 0.1 ng B1 or M1/g and can be completed in 35-45 min.     

Liquid chromatographic determination of aflatoxicol in porcine liver

A liquid chromatographic (LC) method for determination of aflatoxicol in porcine liver was developed. Liver sample is homogenized with water, diluted with saturated Na2SO4 solution, and extracted with acetone. After filtration, less polar interferences are removed by partition with isooctane. Aflatoxicol in the aqueous fraction is partitioned into CHCl3. The extract is dried over anhydrous Na2SO4 and evaporated nearly to dryness at 35 degrees C under a gentle flow of dry filtered air or nitrogen. Residue is dissolved in CHCl3-hexane and applied to a hexane-activated silica cartridge. The cartridge is washed with hexane-CHCl3, then aflatoxicol is eluted with CHCl3-acetone. Purified extract is evaporated to dryness, dissolved in methanol, and analyzed by C18 reverse phase liquid chromatography using a water-CH3CN-acetic acid mobile phase and fluorescence detection. Recovery of aflatoxicol from spiked liver samples at levels ranging from 0.25 to 4.0 ng aflatoxicol/g wet tissue averaged 92% with a limit of detection of about 0.1 ng aflatoxicol/g liver.     

Direct enzyme-linked immunosorbent assay for determining aflatoxin M1 at picogram levels in dairy products

Protocols for detecting picogram quantities of aflatoxin M1 in dairy products were established. Milk samples were subjected to a reverse phase Sep-Pak C18 cartridge treatment before analysis by an enzyme-linked immunosorbent assay (ELISA) according to previously published procedures. M1 in yogurt, brick cheddar, and ripened Brie cheese was extracted by a modified Pons method, subjected to a normal phase silica cartridge treatment, and analyzed by ELISA. The detection limits for M1 in milk, yogurt, cheddar, and Brie were 10, 10, 50, and 25 ppt (ng/kg), respectively. Recovery for M1 added to these products was in the range 70-110%. Good agreement was found for M1 levels in several naturally contaminated milk samples analyzed by both ELISA and liquid chromatography.     

Determination of aflatoxicol and aflatoxins B1 and M1 in eggs

Procedures from 2 methods, one for aflatoxins B1 and M1 in eggs and one for aflatoxicol in milk, blood, and liver, have been combined to determine the 3 toxins in eggs. The sample is blended with sodium chloride-saturated water and this mixture is then blended with acetone. After separation from the solid residue, the aqueous acetone extract is defatted with petroleum ether. The toxins are next partitioned into chloroform and separated from interferences on a silica gel column. Aflatoxicol is determined by fluorescence measurement after separation on a C18 reverse phase liquid chromatographic column, and aflatoxins B1 and M1 are determined by fluorescence densitometry after separation on a silica gel thin layer chromatographic plate. In a recovery study with eggs, mean recoveries of aflatoxicol added at levels of 0.1, 0.05, and 0.025 ng/g were 87, 77, and 78%, respectively. Mean recoveries of aflatoxins B1 and M1 added at a level of 0.1 ng/g were 75 and 87%, respectively, and at an added level of 0.05 ng/g were 86 and 75%. The within-laboratory precision (repeatability) ranged from 2 to 13%.     

Rapid liquid chromatographic determination of aflatoxins M1 and M2 in artificially contaminated fluid milks: collaborative study

An international collaborative study involving 14 collaborators from 5 different countries was conducted to test a rapid liquid chromatographic (LC) method for detecting aflatoxins M1 and M2 in fluid milk. Each collaborator prepared artificially contaminated milk samples (0.078-1.31 ng M1/mL and 0.030-0.13 ng M2/mL) by adding solutions containing various concentrations of aflatoxins M1 and M2 to fresh milk. Recoveries ranged from 85.2 to 102.5% (av. 93.7%) for aflatoxin M1 and from 99.5 to 126.7% (av. 109.8%) for aflatoxin M2. Coefficients of variation averaged 21.4% (M1) and 35.9% (M2). An analysis of variance was calculated from combined data to determine variance components. The within-laboratory variations (So) (repeatability) were 27.9% (M1) and 23.9% (M2), and the among-laboratory variations (Sx) (reproducibility) were 44.5% (M1) and 64.7% (M2). No visual differences were determined between normal or reverse phase LC for contaminated samples; however, there were an insufficient number of collaborators using normal phase to give meaningful separate statistical data. For 26 observations of uncontaminated milk, 3 false M1 positives were reported for normal phase LC determinations and 2 false M1 positives were reported for reverse phase LC determinations. Three normal phase and 11 reverse phase false M2 positives were reported for 104 observations in uncontaminated milk. The reverse phase LC method for determination of aflatoxins M1 and M2 in fluid milk has been adopted official first action.     

Thin layer chromatographic confirmation of aflatoxin M1 extracted from milk

Aflatoxin M1 can be confirmed directly on a thin layer plate by reacting the toxin with a mixture of reagents containing p-anisaldehyde. This confirmatory procedure requires only 2 elutions in the same direction using 2 different solvents. The mixture containing p-anisaldehyde is overspotted on M1 after the plate has been developed in toluene-ethyl acetate-ethyl ether-formic acid (25 + 35 + 40 + 5). The plate is heated at 110 degrees C for 10 min and then developed in hexane-acetone-chloroform (15 + 50 + 35). The Rf value of the green fluorescent derivative is less than that of the M1 standard. This confirmatory procedure requires only one-dimensional TLC, so several sample extracts and the standard can be run simultaneously. The minimum detectable quantity of aflatoxin M1 on the TLC plate with this test is 0.3 ng. p-Anisaldehyde reagent solution may also be used as a spray reagent for the confirmation of aflatoxin M1. The procedures described were satisfactory for confirming the mycotoxin in spiked samples of powdered and liquid milk.     

Rapid reverse phase liquid chromatographic determination of aflatoxin M1 in milk

A rapid, economical, and reliable liquid chromatographic (LC) method is described for determination of aflatoxin M1 in milk. The method includes an improved AOAC extraction procedure, cleanup of the extract on a silica cartridge, and LC quantitation. Alternatively, a rapid column cleanup procedure can be used. Milk artificially spiked with aflatoxin M1 at 0.05, 0.1, and 0.5 ppb was analyzed using both new approaches as well as an AOAC method coupled with LC for quantitation of the toxin. Recovery of aflatoxin M1 by the first approach of the new method ranged between 93.4 and 99.1%, and for the alternative procedure between 92.4 and 96.8%. The AOAC method gave lower recovery (85.6-90.7%) of toxin, but the results from this method had a somewhat smaller standard deviation for replicate analyses than did results of the new method.     

Use of the Mycosep multifunctional cleanup column for liquid chromatographic determination of aflatoxins in agricultural products.

A liquid chromatographic (LC) technique has been developed that uses the Mycosep multifunctional cleanup (MFC) column. MFC columns provide a rapid 1-step extract purification. They are designed to retain particular groups of compounds that may create interferences in analytical methods. At the same time, MFC columns allow compounds of interest to pass through. In the method presented, test samples are extracted in a blender with acetonitrile-water (9 + 1). A portion of the extract is forced through an MFC column designed especially for analysis of numerous mycotoxins. Analytical interferences are retained, while aflatoxins pass through the column. Aflatoxins B1 and G1 are converted to their hemiacetals by heating a mixture of purified extract and water-trifluoroacetic acid-acetic acid (7 + 2 + 1) at 65 degrees C for 8.5 min. An aliquot of this mixture is analyzed by isocratic LC with acetonitrile-water mobile phase and fluorescence detection. A detection limit of less than 0.5 ng/g for aflatoxin B1 was obtained. Average recoveries greater than 95% total aflatoxins (B1, B2, G1, and G2) and coefficients of variation of less than 3% were obtained. The method was successfully applied to the following commodities: corn, almonds, pista-chios, walnuts, peanuts, Brazil nuts, milo, rice, cottonseed, corn meal, corn gluten meal, fig paste, and mixed feeds.     

High pressure liquid chromatographic determination of aflatoxins in corn.

A high pressure liquid chromatographic (HPLC) method is proposed for determining aflatoxins in corn. The sample is extracted with methanol-10% NaCl (4 + 1), pigments are precipitated with zinc acetate, and the extract is cleaned up on a small (2 g) silica gel column. Aflatoxins in the purified extract are resolved by normal phase HPLC on a microparticulate (10 micrometer) silica gel column with water-saturated chloroform-cyclohexane, acetonitrile solvent, and detected by fluorescence on a silica gel-packed flowcell. The method was compared with chloroform-water extraction of the official CB method on 15 samples of contaminated corn. In 5 of the 6 samples containing aflatoxins B1, B2, G1, and G2, methanol-10% NaCl extracted more aflatoxin than did cloroform-water, as measured both by HPLC and by thin layer chromatography. In samples containing only B1 and B2, the 2 extraction solvents were virtually equivalent. Agreement was good between HPLC and TLC for each extraction solvent. Average recovery of aflatoxins B1, B2, G1, and G2 added to yellow cornmeal at 3 levels was greater than 90%.     

Rapid immunochemical screening method for aflatoxin B1 in human and animal urine

A method has been developed to determine the presence of aflatoxin B1 in the urine of animals (including humans) by utilizing commercial immunochemical kits that can be used in the field. Urine is treated with diatomaceous earth and filtered to clarify the sample; 2-3 ppb aflatoxin B1, corresponding to about 300 ppb in the ingested feed/food, can be detected in the filtered urine without further purification. To improve sensitivity, the urine filtrate is passed through a C18 solid phase column to extract the aflatoxin. The column is washed with acetonitrile-water (15 + 85) and water, aflatoxin B1 is eluted with methanol-water (7 + 3), and water is added to the eluate, which is then tested for aflatoxin with the test kit. The limit of detection is 0.2 ppb, reflecting consumption of 40 ppb or more aflatoxin in the feed/food. When the initial sample volume is adequate, purification through the C18 column step is usually sufficient. For limited sample volumes, the eluate from the C18 column is mixed with water, added to an immunosorbent affinity column, and washed with water to remove excess sample matrix and impurities. Aflatoxin B1 is eluted with acetonitrile. The extract is evaporated under nitrogen and the residue is redissolved in methanol-water (25 + 75). At this purification stage, the limit of detection is reduced to 0.05 ppb.     

Liquid chromatographic determination of aflatoxins in feedstuffs containing citrus pulp

A liquid chromatographic (LC) method was developed for the determination of aflatoxins in feedstuffs containing citrus pulp. The feed-stuff sample is extracted with chloroform, followed by Sep-Pak Florisil cartridge cleanup and Sep-Pak C18 cartridge cleanup. The final eluate (water-acetone, 85 + 15, v/v) is submitted to reverse-phase liquid chromatography with water-methanol-acetonitrile (130 + 70 + 40, v/v/v) as mobile phase and postcolumn derivatization with iodine. Citrus components are removed from the extract efficiently. The limit of detection for aflatoxin B1 is less than 1 microgram/kg. Other aflatoxins can also be detected and measured. Recoveries of aflatoxins B1, B2, G1, and G2 for dairy rations spiked at 13, 5, 10, and 4 micrograms/kg were 87, 86, 81, and 82%, respectively. Corresponding coefficients of variation were 3.1, 3.6, 5.2, and 3.8%, respectively.