Experimental Study on a Prestressed Frame of Two Spans Under Unsymmetric Load

By the experimental study on a full-dimensioned prestressed frame of two spans, the relative factors are analyzed such as relative height of equivalent compression zone in critical section, secondary moment, ratio of beam rigidity to column and development of cracks in the top of columns etc., which influence the moment distribution of the post-tensioned prestressed concrete frame from the side of internal force redistribution. It is believed that that the factors of relative height of concrete equivalent compression zone and secondary moment influence the moment modulation in most degree, and ratio of column rigidity to beam also plays a part in the moment modulation to some extent. Second, the plastic joints of frame with excessive spans exit in the span which endure the whole load, at last the whole frame is destroyed because of the destruction of the loading frame, the influence to the non-loading span is little.     

Discussion on the Secondary Moment of Prestressed Frame

The secondary moment of prestressed concrete frame is different from that of continuous beam. In this paper,the principle and calculation method of equivalent load secondary moment and axial secondary moment are discussed,and the infection of secondary moment in moment modulation is analyzed,together with the suggestions of moment modulation for prestressed concrete frame with adopting the total control. The suggestions would be able to distinguish the advantageous and disadvantageous effect of secondary moment. Some helpful advises for moment modulation design are given in this paper.     

Test Analysis on Prestressed Frames with Three Kinds of Beam-column Section Strength

"Strong column with weak beam","strong beam with weak column" and"column & beam with equal strength"can be existed in one-storey prestressed concrete frames and the top storey of mult-storey prestressed concrete frames.Through the test of four prestressed concrete frames under vertical load,three kinds of prestressed concrete frames performances are studied,such as ultimate load,deflection,displacement ductility,redistribution of internal force.When the relative height of equivalent compression zone is smaller enough,the test proves that three kinds of prestressed concrete frames can realize full redistribution of internal force and have better displacement ductility,the width of cracks and deflections can satisfy the rules of code for design of concrete structures.     

A Study on the Test Method of Post-tensioned Prestressed Concrete Continuous Beam

A test method of post-tensioned prestressed concrete continuous beam is presented in this paper.In the test,the prestressed secondary moment is established by adjusting middle support height.The prestressed concrete continuous beam built by the method is equivalent to the beam in practice.     

Inelastic Seismic Response of Ordinary Reinforced Concrete Regular Frames

With an inelastic dynamic analysis program developed by the authors, seismic response analysis of regular RC frames designed to Chinese codes in different earthquake fortification zones are carried out. The results indicate that the displacement responses of structures are improved due to the more rigorous limitation on the inter-story drift under frequent earthquakes in the revised codes. The frames in seismic-intensity-9 zone designed to the former codes and the revised codes form plastic energy-dissipated mechanisms mostly With beam hinges, which can satisfy the requirement of seismic performance expectably. The frame in seismic-intensity-8 zone designed to the former code forms a plastic energy- dissipated mechanisms mostly with column hinges and shows a risk of occurrence of story-sway mechanism, while the frame in seismic-intensity-8 zone designed to the revised codes exhibits a relatively improved seismic performance but still with excessive column hinges, which suggests a need to further increase the column moment amplification measures for this kind of frames. The frame in seismic-intensity-7 zone shows a somewhat improved seismic performance than the frames in seismic-intensity-8 zone, but the protection to columns by the seismic measures is sill insufficient, which indicates that the column moment amplification measures for this kind of frames should be enhanced further.     

Experimental Investigation of "Column with Weaker Beam" Frame and "Column with Equally Strong Beam" Frame

By the way of experiment and analysis of two "one story and one bay" reinforced concrete frames, namely a "beam with weaker column" frame and a "column with equally strong beam" frame, the features of internal force redistribution are investigated and an elementary comparison about bending moment redistribution of three kinds of frames namely the "column with weaker beam", "beam with weaker column" and "column with equally strong beam" is given. Through this comparison, the objective existence of such "three kinds of frame" is proven, the moment redistribution is different for each frame and for the moment modulation, the elastic moment diagram and the difference of the internal force redistribution in different frames should be considered together.     

A Study on the Test Method for Post-tensioned Prestressed Concrete Frame

A creative test method for post-tensioned prestressed frame is presented in this paper. In the test, the stationary supports at the column base are simulated and the forces at the column base can be tested while the two column bases are not connected with concrete beam. The prestressed secondary moment and the weight-produced moment are established by adjusting the support device at the column base. In this paper, the necessary conditions of the method and the basic process are recommended. It is proved theoretically that the prestressed concrete frame built by this method is equivalent to that used in practice.     

Several Matters to be Noticed During the Moment Modulation Design of Prestressed Concrete Frame

The moment modulation of prestressed concrete frame has some differences compared with that of continuous beam.Based on the analysis of ratio of column linear rigidity to beam one,form of load,second moment and plastic hinge in column,this paper is intended to get some helpful advise for moment modulation design.     

竖向荷载下弹性支承直墙拱反弯点理论分析

在工程实践中,直墙拱应用较多。由于拱脚位移的存在,合理假设拱脚约束为转角约束、竖向约束和水平弹性约束,应用力法推导出了在弯矩、剪力和轴力共同作用下直墙拱沿弧长的弯矩公式。研究了竖向均布荷载、竖向三角形荷载和竖向集中力荷载作用下,直墙拱沿弧长的弯矩分布及反弯点形成的规律;发现在3种荷载作用下,使得拱脚弯矩为零时的圆心角依次减小。取弹簧支座刚度为等效的下端固支、上端允许水平位移的直墙的抗推刚度,得出了随着直墙高度增加,圆弧拱拱顶弯矩增大而拱脚弯矩减小的变化规律。在直墙拱的设计中,建议选取合适的直墙高度和使得圆弧拱拱脚弯矩为零的圆心角大小,从而有利于提高结构抗弯承载力及拱脚抗剪承载力。     

EXPERIMENTAL RESEARCH OF THE MOMENT MODULATION INFLUENCE ON CRACKING AND DEFLECTION OF CONTINUOUS REINFORCED CONCRETE BEAMS UNDER SERVICE LOADS

Through the static tests of five two-span continuous beams with a relatively small steel ratio, the regularity of redistribution of internal forces of continuous beams with moment modulation is studied, and the moment modulation influence on cracking and deflection of continuous reinforced concrete beams under service loads is analyzed in detail. The conclusions obtained may be used as reference materials for drafting of design code considering redistribution of internal forces.     

Analysis Theory of Unbonded Prestressed Concrete Continuous Beams

In this paper, the energy method has been used to study the change of the secondary moment of unbonded prestressed concrete continuous beams and it has been contrasted with bonded prestressed beams. The question, whether the secondary moment changes or not while loading, was answered. It shows that the primary secondary moment does not change when increment method is adopted to study the beams, but the total secondary moment will change while the force in prestressed reinforcement changes.     

Comparative Study on Plastic Hinges of Prestressed Concrete Frames Under Vertical or Horizontal Loads

In With one-storey, two-span prestressed frames, a comparative study is done between under vertical and horizontal loads. The studies include the pattern of the plastic hinges occurring and, the demanded and available rotational capability of the hinges in critical sections. The relative height of compression zone and prestressed degree are considered. The result indicates that there is much difference in the pattern of the plastic hinge occurring when each plastic hinge has enough rotational capability. The beams can finish a full redistribution of internal force under vertical loads, but not under horizontal loads. Moreover, as increasing of the relative height of compression zone, a stronger rotational capability of hinges will be demanded to finish a full redistribution under vertical loads when a weaker rotational capacity will be needed under horizontal loads.     

Suggestion for Moment Modulation of Prestressed Concrete Continuous Beams

Based on the information from China and overseas,a design suggestion for moment modulation of post-tensioned prestressed concrete continuous beams with bond has been put forth in this paper. The result calculated by the suggestion is consistent with the result of varying rigidity method.     

Strictly Analytic Calculation to the Renormalized Finite Quantity of the Photon Loop(Chain) Propagator

In the minimum electromagnetism coupling model of interaction between photon and electron(antielectron),Feynman convergence integral method is often used to deal with the finite quantity of one-loop correction scheme.After analyzing,discussing and researching the method,a new method is found.That is the great moment integral limitation method.Through the method,the relative result is obtained.     

Mechanical Behaviors and Design Method for Irregular Joints in Rigid Steel Frames

In order to study the mechanical behaviors of irregular joints in rigid steel frames which had been used in large scale power plant, 6 specimens in 1/4 scale of the prototype model were designed according to different axial compression ratio and section height ratio of beams and were tested under low cyclic reversed loading.Based on the failure law of specimens, the main factors that affect the bearing capacity of the irregular joints were analyzed.By the division of panel zone, the calculating formula was put forward according to mechanical principles.It is found that the difference between calculating results and experimental results is about 18%.And the proposed method for calculating the irregular joints in rigid steel frames is feasible.     

A new measurement method for mass property parameters

Mass property parameters (mass, center of mass, moment of inertia) are important technology parameters of aircraft. The traditional mass and center of mass measurement uses centroid units, and the moment of inertia measurement torsion units, which can only get results in installing direction. Because of the structural reasons, there is a need to get all high accurate physical parameters in clamping once. To solve this problem, this study merges centroid units and torsion units into one composite unit, installs a table which can tilt and rotation to measure the moment of inertia in different conditions. The moment of inertia and product of inertia relative to three axis are calculated by the method of coordinate transformation. Measurement theory of mass, center of mass and mass moment of inertia are described, the main reason of causing measurement errors is discussed, and the measurement accuracy affected by tilt error is analyzed.     

Y形偏心支撑高强钢框架结构抗震性能

在Y形偏心支撑高强钢框架结构抗震性振动台试验的基础上,建立了试验试件的有限元模型,并验证了分析的正确性。设计了一个9层的Y形偏心支撑高强钢框架结构,以耗能梁段长度、耗能梁段腹板高厚比、高跨比为参数,对9层结构进行了非线性动力时程分析,研究了以上参数对结构抗震性能的影响。研究结果表明,改变耗能梁段长度、高跨比对结构层间侧移、耗能梁段性能、框架柱弯矩、耗能能力均有不同程度的影响,对框架柱轴力、基底剪力无显著影响;改变耗能梁段腹板高厚比对结构耗能能力有影响,对结构层间侧移、耗能梁段性能、框架柱受力、基底剪力无显著影响,并给出了相关设计建议。     

可拆式钢筋桁架模板截面力学性能试验和计算方法

通过对全尺寸可拆式钢筋桁架模板在施工阶段的截面力学性能试验,研究了其在单调荷载作用下的破坏形态以及受力机理。并分别采用荷载挠度曲线法和极限弯矩法计算了截面特性。分析表明：施工阶段可以采用上下弦连续的桁架计算模型,荷载挠度曲线法计算结果与理论值偏差较大,其原因是：试件破坏过程由变形控制,而非强度,以及由于连接件与钢筋的相对滑移产生的附加挠度,极限弯矩法计算值与理论值较为吻合。在此基础上,给出了简支或等跨连续（两跨）梁计算模型的最大无支撑长度的建议值。     

The Effect on the Column Moment Considering Compress of Prestressed Concrete Beam

Axial compress is produced by the tension of prestressing beam, which engenders the third moment of column. And the third moment is always ignored in design. The thesis analyses elementarily the third moment of column and finds that the third moment must be taken seriously in some condition, and it is not the same value as the manner of tensions is different . As a result, some helpful conclusion and suggestion are presented.     

Calculation and Analysis on Critical Moment of Thin-walled Beams under Unequal End Moment

In this paper, comparing the bending-twisting model with the tension-bending one, the critical moment of the thin-walled beams under unequal end moment is derived easily by the improved CDC (column deflection curve) method based on the increment interaction equations of beam-columns.A simplified formula is presented and the calculated results show a good agreement with the numerical ones.