Structural characteristics of corn starches extruded with soy protein isolate or wheat gluten

Commercially available corn starches containing 0, 25, 50 and 70% amylose were extruded with 10, 20 and 30% soy protein isolate (SPI) or wheat gluten (WG) at 22% moisture content (dry basis) in a C.W. Brabender single screw laboratory extruder using a 140°C barrel temperature and a 140 rpm screw speed. True, solid and bulk densities; percent total, closed and open pores; and shear strengths of the extrudates were determined. The microstructures of the extrudates were studied by scanning electron microscopy (SEM). The total pores of the extrudates were affected significantly (p < F=0.0001) by type of protein (SPI or WG) and starch amylose. The open or closed pores, were affected by protein type only. The interaction between amylose and protein contents was highly significant <(p < F=0.0001). In general, the total pores and bulk densities were higher for WG-starch extrudates compared to SPI-starch extrudates. These values decreased as amylose content increased from 0 to 25% and then increased thereafter. The open pores, on the other hand, increased with increasing protein content from 10 to 20% and then decreased. Extrudates containing WG had higher shear strengths than those containing SPI.     

Preparation and characterization of a novel antibacterial fiber modified by quaternary phosphonium salt on the surface of polyacrylonitrile fiber

A novel antibacterial fiber named MTPB-PANF was synthesized by chemical modification of polyacrylonitrile fiber (PANF). The PANF was firstly reacted with alkali solution to get Na-PANF with -COONa functional groups. Na-PANF was then reacted with different concentration of methyltriphenyl phosphonium bromide (MTPB) into flasks, and the whole system was immersed into a to and fro vibrator. During the synthesis process, this paper investigated on the initial concentration of MTPB, the contact time, the reaction temperature and the pH of the solution that may have effect on the properties of the final fiber. The properties of MTPB-PANF were discussed by fourier transform infrared spectroscopy (FTIR), thermo gravimetric analyzer (TGA), scanning electron microscope (SEM) and the stability of organophosphorus groups on MTPB-PANF examined by inductively coupled plasma atomic emission spectrometry (ICP-AES). The antibacterial activity of MTPB-PANF was examined against pathogenic Escherichia coli and Staphylococci aureus by improved shake flask method in sterile saline and was evaluated by the viable cell counting method. The obtained results showed an excellent antibacterial activity of MTPB-PANF. And the antibacterial mechanism was discussed by the concentration of K⁺ released from cells after bacterial testing.     

Processing and characterization of nickel-plated PBO fiber with improved interfacial properties

A new application of conventional electroless nickel plating to improve the interfacial properties of PBO fibers was reported. The relationship between surface morphology and interfacial properties of nickel-plated PBO fiber was explored. The continuous nickel coating consisted of nickel and phosphorus elements determined by Energy dispersive spectrometer (EDS) and transmission electron microscope (TEM), exhibiting high adhesive durability. The influence of bath temperature and plating time on the crystal structure, microstructure and mechanical properties of nickel-plated PBO fibers was systematically investigated. X-ray diffractometer (XRD) results revealed that the crystal structure among nickel-plated PBO fibers did not show differences. Scanning electron microscope (SEM) and Atomic force microscope (AFM) images showed that the process parameters had a great influence on surface morphology and roughness of nickel-plated PBO fibers, which could directly affect the interfacial properties of nickel-plated PBO fibers. Single fiber pull-out testing results indicated that the interfacial shear strength (IFSS) of PBO fibers after electroless nickel plating had a significant improvement, which reached maximum at 85 °C for 20 min. Single fiber tensile strength of nickel-plated PBO fibers was slightly lower than that of untreated one. Thermo gravimetric analysis (TGA) indicated that nickel-plated PBO fiber had excellent thermal stability.     

Modification of polyacrylonitrile precursor fiber with hydrogen peroxide

Polyacrylonitrile (PAN) precursor fibers were modified for different periods of time using hydrogen peroxide aqueous solution. A variety of tests were employed to characterize the fibers. The modification could induce cyclization and oxidation in the precursor fibers, as reflected by the changes in length and diameter of the fibers, and the results of Fourier transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS). Compared with the unmodified fiber, the modified fibers released less heat during a heating process similar to stabilization of PAN precursor fiber. Also, the modified fibers showed lower characteristic temperatures on differential scanning calorimetry (DSC) thermograms, and lower onset temperature of weight loss on thermal gravimetry (TG) curves. The modified fibers had more surface defects and hence exhibited lower tenacity and tensile modulus. Compared with the unmodified fibers, however, the modified fibers had smoother surface and fewer defects after stabilization. The strain decreased with increasing temperature under a constant tension for all the fibers. At the temperatures above 200 °C, the shrinkage of the fibers decreased with the increase of modification time, because a certain degree of cyclization and oxidation occurred in modified fibers, making them shrink less in the temperature range equivalent to stabilization.     

Polypyrrole/polyacrylonitrile composite films: Dielectric, spectrophotometric and morphologic characterization

Spectrophotometric, morphologic and dielectric properties of polyacrylonitrile (PAN) composite films in the presence of pyrrole derivatives were reported in this paper. The composite films were fabricated by oxidative polymerization of pyrrole (Py), N-methyl pyrrole (NMPy) and N-phenyl pyrrole (NPhPy) by cerium(IV) on polyacrylonitrile matrix. The effect of temperature on the dielectric properties was studied in the frequency range from 0.05 Hz up to 10 MHz and in the temperature range from 0 °C up to 250 °C. Conductivity was increased with temperature due to increase of the mobility of charge carriers in the composite films. By increasing the temperature, the dipoles become free and respond to the applied electric field in composite structure; thus, the polarization and dielectric constant increases. PNPhPy-PAN composite films exhibited the highest dielectric constant, AC conductivity and tan delta.     

Studies on a novel polyacrylonitrile copolymer/cellulose acetate blending water absorbency fiber

Polyacrylonitrile copolymer (CPAN) was obtained by water-deposit polymerization, using acrylonitrile (AN), vinyl acetate (VAc), potential crosslinking moiety (hydropropyl acrylate, HQ) as monomer, NaClO₃ as initiator. CPAN was blended with cellulose acetate (CA) to prepare CPAN/CA blending fiber via wet spinning. The fiber was post-crosslinked and hydrolyzed to get water absorbency fiber. The structures and properties of the fibers were studied and the results showed that potential crosslinking moiety was necessary in making CPAN/CA blending water absorbency fiber. The saponification reaction was accelerated after blended with CA and the interfacial microvoids enhanced the water absorbency ability.     

The USDA trypsin inhibitor study. IV. The chronic effects of soy flour and soy protein isolate on the pancreas in rats after two years

In two year feeding trials, histologic changes in the pancreas of the Wistar rat were evaluated after chronic dietary exposure to raw and heated, dehulled, defatted soy flour and soy protein isolates which provided a range of trypsin inhibitor (TI) concentrations from 93 to 1271 mg/100 g diet. Also investigated was the nutritional interaction of level of dietary protein with the development of pancreatic pathology. Graded levels of TI were achieved from mixtures of raw and heated soy flour or protein isolate. Dietary protein levels were 10%, 20%, and 30%; the two higher levels obtained in some diets through casein supplementation. A total of 26 diets, including casein controls, were fed to groups of 40 male rats. Growth rates with these diets were commensurate with protein quality and level. Mortality rates tended to be slightly greater in the higher protein diets, and rats fed only raw soy as a source of protein survived well.Two lesions, nodular hyperplasia (NH) and acinar adenoma (AA) constituted the major pathological findings in the pancreas, and the incidence rates of both were positively associated with the concentration of dietary TI. The incidences of pancreatic NH and AA compared to those of the corresponding casein control were significantly elevated in rats fed heated soy flour supplying 10% protein and the lowest level of TI investigated (93 mg/100 g diet). At low levels of TI (215 mg/100 g diet), supplementation by casein to raise the concentration of protein from 10% to 20% and 30% reduced the frequency of NH and AA. When the dose-response data for NH and AA was linearized by plotting the probit of percent incidence against log of TI concentration per gram of dietary protein, the response to soy flour and soy protein isolate was not significantly different. Numerous lesions commonly found in the aging rat were diagnosed, and modulation of their rate of occurrence by nutritional factors associated with the diets was apparent in some instances.Reference to a company and/or product named by the Department is only for purposes of information and does not imply approval or recommendation of the product to the exclusion of others which may also be suitable.     

Mechanical property optimization of wet-spun lignin/polyacrylonitrile carbon fiber precursor by response surface methodology

Lignin, nature’s abundant polymer with a remarkably high carbon content, is an ideal bio-renewable precursor for carbon fiber production. However, the poor mechanical property of lignin-derived fibers has hindered their industrial application as carbon fiber precursor. In this work, process engineering through the application of computational modeling was performed to optimize wet-spinning conditions for the production of lignin precursor fibers with enhanced mechanical properties. Continuous lignin-derived precursor fibers with the maximum possible lignin content were successfully produced in a blend with polyacrylonitrile, as a wet-spinning process facilitator. Response surface methodology was employed to systematically investigate the simultaneous influence of material and process variables on mechanical properties of the precursor fibers. This allowed generating a mathematical model that best predicted the tensile strength of the precursor fibers as a function of the processing variables. The optimal wet-spinning conditions were obtained by maximizing the tensile strength within the domain of the developed mathematical model.     

Depositon of ZnO on polyacrylonitrile fiber by thermal solvent coating

In this study, the surface functionalization of polyacrylonitrile (PAN) fibers was achieved by depositing ZnO nanoparticles using thermal solvent coating. surface morphology, crystalline structure, surface chemistry, thermal stability and washing stability of the ZnO coated PAN fibers were investigated by scanning electron microscope (SEM), X-ray diffractometer (XRD), Fourier transform Infra red spectroscopy (FT-IR), Thermo-gravimetric analyses (TGA) and washing stability test, respectively. In addition, the weight changes after coating and washing were studied at different coating and washing conditions. The SEM images revealed that the ZnO was well coated on the surface of the PAN fibers and the coating was obviously affected by the experimental temperature. The FT-IR spectra indicated the chemical features of the deposited ZnO nanostructures. The XRD patterns showed that there was a typical crystalline structure of ZnO nanogains formed on the PAN fibers after coating. The TGA results revealed that the thermal stability of the PAN fibers was improved by the ZnO coating. The experimental results of washing stability revealed the effect of temperature on the washing stability. Weight measurements indicated that the amount of ZnO deposited on PAN fibers increased with the increasing of coating temperature from 60 to 70 °C. Weight measurements also revealed that the weight of the ZnO coating on fibers decreased with the increase in washing temperature and washing time.     

Preparation and characterization of polyurethane foam using a PLA/PEG polyol mixture

Polyurethanes are polymers with urethane linkages in their backbone. It is prepared by polyaddition polymerization between isocyanates and polyols, which produce different chemical, physical, and mechanical properties depending on their types and characteristics. Previous reports of polyurethane foams prepared by using PEG polyol indicated prominent features in the elasticity and recovery of the foams. However, it is necessary to improve the mechanical strength of these materials. In this study, polyurethane foams were prepared using a PLA/PEG polyol mixture and 1,6-hexamethylene diisocyanate. PLA polyol was synthesized by the direct condensation polymerization of lactic acid. The polyurethane foams were characterized using FE-SEM analysis, FT-IR spectroscopy, water absorbency measurement, and mechanical property measurement. In FE-SEM analysis, it was shown that the PLA content of polyol mixture significantly affected the porous structure. FT-IR spectra confirmed that urethane linkages formed between the PLA/PEG polyols and the isocyanates. The water absorbency decreased due to the hydrophobicity of PLA. With respect to the mechanical properties, the breaking stress and the Young’s modulus increased with increasing PLA content. When the PLA content of polyols was 60 and 70 percent, the breaking strain was significantly higher than those of other polyurethane foams.     

The nutritional properties of extruded and non-extruded corn fiber isolate

The feed efficiency and selected organ weights of rats fed diets containing 3 or 7% corn fiber, extruded corn fiber or silica were compared to rats fed a fiber-free diet. No significant differences were found in feed efficiency, spleen, lung or liver weights for any of the treatments relative to the fiber-free control diet.     

The characterization of polyacrylonitrile fibers stabilized by electron beam irradiation

This study investigates polyacrylonitile(PAN) fibers stabilized with various doses of electron beam irradiation (EBI) ability to produce carbon fibers. Feasibility was verified by FT-IR, the percent of gel fraction, density, DSC, XRD, and mechanical measurements. FT-IR spectra showed that the intensities of the stretching C??N bonds decreased at 2,244 cm^?1 with increasing EBI dose. This de crease was related to cyclization of nitrile groups during EBI-stabilization. The degree of cyclization was determined from the gel fraction and density tests. The gel content and density of PAN fibers stabilized by EBI increased with an increase in the EBI dose. Thermal properties were characterized by differential scanning calorimetry (DSC) and thermally activated reactions. DSC curves showed that EBI treatment influenced the quantity of released heat and the exothermic position at low temperature over a wide temperature range. The strongest diffraction peak from the PAN precursor fiber arose from the (100) plane; its stabilization index (SI) was evaluated by X-ray diffraction. The X-ray results showed that the peak intensity decreases gradually with increasing EBI dose. In addition, tensile strength decreased the EBI stabilization level.     

Air-gap spinning of cellulose/ionic liquid solution and its characterization

In order to study the effects of the spinning conditions on the structure and the properties of the regenerated fiber, cellulose was dissolved in ionic liquid and then spun into fiber using an air-gap spinning process. The solution concentration, the take-up speed and the fixation of the fiber ends during coagulation improved the crystallinity and the tensile strength at the same time. The fiber surface became smooth by addition of DMF (dimethylformamide). However, it decreased the crystallinity and the tensile strength of the fibers. We revealed that the developed structure during coagulation determined the morphology and the properties of the fibers. The co-solvent resulted in smooth surface of the fiber and also changed the mechanical properties.     

大豆分离蛋白膜法连续与间断超滤工艺技术

大豆分离蛋白超滤膜法中,在选用合适的膜材质条件下,采用连续和间断过滤工艺技术,不仅满足各工段的要求,还使蛋白质得率提高,减少用水量。     

Analysis of glycolysis products of polyurethane fiber waste with diethylene glycol

Diethylene glycol and dibutyl tin dilaurate were used to degrade polyurethane fiber waste in this paper. The glycolysis products were separated into two phases including white solid and brown liquid by a freezing process. The chemical structure and thermal property of the purified solid product were characterized by Fourier transform infrared (FTIR) spectrometer,¹H nuclear magnetic resonance (¹H NMR) and differential scanning calorimetry (DSC). The solid product was mainly polytetrahydrofuran. The analysis of the liquid product was carried out by FTIR and high performance liquid chromatography-electrospray ionization-mass spectrometry (HPLC-ESI-MS). The liquid phase included various components such as aromatic amine, diethylene glycol-propylene diamine compound and so on. The glycolysis mechanism of polyurethane fiber waste is also discussed in this paper.     

Human urine and/or plasma levels of methionine,methionine sulfoxide,and inorganic sulfate after consumption of a soy isolate: A preliminary study

In a preliminary study, three human subjects consumed 35 or 70g of a commercially available soy isolate containing 298 or 596 mg of methionine sulfoxide. Methionine sulfoxide appeared in human plasma within one hour after consumption of the isolate. This observation suggests rapid absorption by humans of this oxidized form of methionine. Plasma levels of sulfoxide as determined in one subject returned to zero within 24 hours of consumption of the isolate. Ingested methionine sulfoxide was excreted in the urine in free form in very small quantities relative to intake. These results are consistent with, but of course do not prove, utilization of methionine sulfoxide as a methionine replacement in human subjects.     

Preparation of aminated polyacrylonitrile porous fiber mat and its Application for Cr(VI) ion removal

Porous polyacrylonitrile (PAN) fiber mat was prepared by electrospinning PAN in N,N-dimethylformide solution with poly(methyl methacrylate) (PMMA) as pore-forming agent. Then, the porous PAN fiber mat was chemical modified by the tetraethylenepentamine to acquire aminated porous polyacrylonitrile (APPAN) fiber mat. Common aminated PAN fiber mat was also prepared for comparison. The surface morphologies of the APPAN and PAN fiber mat were characterized by scanning electron microscopy (SEM) and the corresponding specific surface areas were also measured. FT-IR/ATR spectra of the APPAN and PAN fiber mat were recorded for analysis of the surface chemical structures. The Cr(VI) absorption results demonstrated that the porous structure in the fiber could obviously increase the absorption capacity of the fiber mat.     

Electrospinning and microwave absorption of polyaniline/polyacrylonitrile/multiwalled carbon nanotubes nanocomposite fibers

Electrical conductive nanocomposite fibers were prepared with polyaniline (PANI), polyacrylonitrile (PAN) and multi-walled carbon nanotubes (MWCNTs) via electrospinning. The morphology and electrical conductivity of the PANI/PAN/MWCNTs nanocomposite fibers were characterized by scanning electron microscope (SEM) and Van De Pauw method. Electrical conductivity of nanocomposite fibers increased from 1.79 S·m^?1 to 7.97 S·m^?1 with increasing the MWCNTs content from 3.0 wt% to 7.0 wt%. Compared with PANI/PAN membranes, the mechanical property of PANI/PAN/MWCNTs nanocomposites fiber membranes decreased. The microwave absorption performance of composite films was analyzed using waveguide tube, which indicated that with the thickness increasing the value of R_L reduced from ?4.6 to ?5.9 dB.     

Enhanced mechanical and thermal properties of carbon fiber composites with polyamide and thermoplastic polyurethane blends

In this article, we demonstrated the preparation of carbon-fiber-reinforced composites using a polyamide 6 (PA6)/thermoplastic polyurethane (TPU) blend, in which the addition of TPU resulted in superior mechanical performances and increased thermal stability. According to various characterization techniques, these results are attributed to an enhanced adhesion and a homogeneous dispersion of long-carbon-fibers (LCFs) with TPU sizing in blended polymer matrix. Above all, dynamic-mechanical thermal analysis (DMTA) measurements clearly show that the dynamic storage modulus (E') of the blend composites is increased by threefold with temperature ranges below and above the glass transition temperature. The presence of LCFs in TPU systems induces effective fiber orientation, exhibiting simultaneous improvements in the tensile strength, flexural strength, and thermal stability.     

Morphological and crystalline characterization of NaOH and NaOCl treated Agave americana L. fiber

This study investigates the effect of NaOH and NaOCl treatments on chemical composition, morphology and crystalline structure of Agave americana L. fibers. These fibers have been subjected to NaOCl and NaOH alkali treatments at different concentrations.The percentages of lignin and hemicellulose show a decrease with alkaline treatments which, in turn, induces a modification of both morphological and crystalline structures.Unit cell dimensions and crystallite size were more affected with NaOH treatment than NaOCl one. This may result from the mercerisation process which occurs with caustic soda treatment.The observed defibrillization on the treated fiber surface proves the dissolution of the non-cellulosic components present in the fiber cell wall by NaOH and NaOCl treatments. These morphological changes may improve the interaction between matrix and fiber in composites.