杉木管胞具缘纹孔膜超微构造

轴向管胞是针叶材中的主要细胞,它的体积约占木材体积的90%以上,其主要功能是输导水分及强固树体(申宗圻,1984).     

广西融水特色红心杉木优树材质性状变异规律研究

[目的]通过测定和分析广西融水种源红心杉木优树材质性状指标,以了解该地区红心杉木材性状变异规律。[方法]以广西融水种源60株20年生的红心杉木优树为研究材料,测定单株材积、红心率、基本密度、组织比量、管胞性状、微纤丝角等10个材质性状指标,分析各材性性状指标分布和变异规律及性状间的相关关系。[结果]表明:红心率、基本密度、木射线比量、管胞比量、管胞长、管胞宽、管胞长宽比等性状数据分布服从正态分布。融水两个地区红心杉优树轴向薄壁细胞比量的变异系数分别为35.08%和44.97%,变异较大。管胞比量变异系数分别为3.28%和3.56%,变异较小。红心率、木射线比量、管胞长、管胞宽、微纤丝角等性状差异极显著(P0.01),轴向薄壁细胞比量差异显著(P0.05)。10个材质性状间存在12对表型显著相关。[结论]测定的10个性状均是连续性数量性状。早、晚材的管胞长度、管胞宽度和管胞长宽比等性状数据呈从心材至边材逐渐增加的规律。作为重要经济性状的红心率与木射线比量呈极显著正相关(P0.01),单株材积与轴向薄壁细胞比量呈显著正相关(P0.05),而单株材积与基本密度的相关性不显著,这使红心杉木生长量与材性相结合的遗传改良成为可能。     

The effects of drying on the structure and permeability of the wood of Abies grandis

Summary The effects of air-drying and solvent-drying on the sapwood of Abies grandis have been investigated by a new method for the determination of the size and number of conducting tracheid lumina and pit membrane pores which involves the measurement of gaseous permeability at various mean pressures. Both earlywood and latewood tracheids (83% of the total) were found to be conducting in solvent-dried wood, but in air-dried wood only latewood tracheids (32% of the total) were conducting. In solvent-dried wood there were on average 27,000 pit membrane pores per conducting tracheid compared with only 600 in air-dried wood. In both, the average pit membrane pore radius was about 0.1 m.Liquid permeabilities have been predicted from the calculated radii and numbers. The liquid permeability of solvent-dried wood was 31 times greater than that of air-dried wood in which the lumina were responsible for 13% of the total resistance to flow. The lumina were responsible for 39% of the resistance in solvent-dried wood and it is suggested that in first-formed earlywood the lumina may cause more than half the total resistance.A new method is described for the cleaning of direct carbon replicas of wood. In this the cellulose is removed by cellulase instead of sulphuric acid, and no wax backing is required. This provides much cleaner replicas. Electron micrographs have been obtained of both earlywood and latewood dried by the two methods.The authors wish to thank Mr. A. R. Sayers for preparing the computer programme used in this work, Dr. R. Ph. C. Johnson for his help and advice regarding the electron microscopy and Professors Matthews and Weatherley for their advice and encouragement.     

3种不同处理方法对木材渗透性影响的研究

本文通过对长白鱼鳞云杉和臭冷杉生材分别进行普通气干处理和酒精置换处理以及对其气干材进行水浸处理,研究了这３种不同处理方法对木材气渗透性的影响及其影响机理。研究结果表明,长白鱼鳞云杉边材、心材和臭冷杉心村的生材经普通气干处理后,其气体渗透性较低,分别约为０．１１４、０．０４５和０．１１１ｄａｒｃｙ;长白鱼鳞云杉边材、心材和臭冷杉心材的生材经酒精置换处理后,其气体渗透性分别约为１１．７１３、０．０７４和０．１４４ｄａｒｃｙ,比普通气干处理对照组试样的平均渗透性分别增加约１０１．５倍、６２％和３０％,ｔ检验表明,前者差异非常显著,但后两者差异不显著;已气干１８个月的长白鱼鳞云杉边材、心材和臭冷杉心材经水浸处理后,其平均气体浸透性较处理前分别增加约８５％、４９％、６５．５％,ｔ检验表明差异均显著。长白鱼鳞云杉生材边材经     

栽培措施对短周期工业材材性影响规律的研究

对4种不同栽培措施的日本落叶松、湿地松、马尾松和杉木等多种短周期工业材309株样木的材性进行了全面测试分析研究，结果表明．立地指数大，木材生长率和纤维宽度大．但纤维长度、纤维长宽比、木材基本密度、顺纹抗压强度和抗弯弹性模量减小；立地指数相差两级，木材的年龄宽度、纤维宽度、长度和微纤线角度的差异达到显著或极显著水平栽植密度小，木材的年轮宽度和干缩比增大但纤维长宽比及体积全干缩率减小；栽植密度增大，杉木和昭林6号杨木材的力学强度提高，但尾叶桉和I－69杨降低；不同栽植密度的木材pH值及酸碱总缓冲容量，都是心材大于边材，但木材的脲醛树脂胶凝速度，则是边材快于心材.与未间伐林分的木材比较，随着间伐强度的增大、年轮宽度增大．但纤维长宽比和微纤丝角度减小；间伐强度增大，针叶树村的力学强度降低，阔叶树树则提高．但将强度间伐材（间代40％）与未间伐材比较，结果完全相反；北京杨木材心材的pH值、酸碱缓冲容量及总容量，均随间伐强度的增大而增大，但边材却减小．施肥措施能够增大纤维直径，但将导致纤维长宽比、木材密度和力学强度的降低施肥可以使树木速生，但会降低木材密度和质量，在培育建筑结构材的林分应慎用．     

Liquid water absorption in dried Norway spruce timber measured with CT scanning and viewed as a percolation process

Liquid flow in dried wood is complicated to study, since wood is a nonhomogeneous, hygroscopic-porous, anisotropic material. However, liquid flow is important to understand, since it has an influence on the durability of wood and on such processes like impregnation, drying, surface treatment, etc. In this study, simulations of liquid water absorption in wood as a fibre network, percolation, were compared with experimental water absorption in the longitudinal direction in spruce timber. With CT scanning, water distribution during liquid flow can be shown visually and measured by image processing. Liquid water absorption in end grain of spruce was measured with CT scanning after 1, 3, 7 and 14?days of liquid water absorption and shown as moisture content (MC) profiles in heartwood and sapwood. It was found that the amount of water absorbed could be expressed as a linear function of the square root of time. The slopes of the lines differed between sapwood and heartwood and also varied depending on the growth condition of the trees. The simulations according to the percolation method show generally good agreement with the measured results for sapwood.     

马尾松木材横向液体渗透性的研究

分析和讨论了影响马尾松木材横向液体渗透性及其各向异性的机理.对马尾松木材的径向液体渗透性和弦向液体渗透性进行了测量.结果表明,马尾松木材的径向液体渗透性大于弦向液体渗透性,并且,马尾松木材的径向液体渗透性和弦向液体渗透性都是从边材向心材逐渐减小,并随着含水率的下降而升高.其原因是径向液体流动的主要通道是木射线和水平树脂道,弦向主要是管胞壁和交叉场上的纹孔.     

Soft X-ray observation of water distribution in the stem ofCryptomeria japonica D. Don I: General description of water distribution

Water distribution in green stems ofCryptomeria japonica D. Don was observed by soft X-ray photography. In the sapwood, much water was present and evenly distributed. In the intermediate wood (the white zone), little water was present. The intermediate wood appeared in all cross sections of the stem and separated the heartwood from the sapwood in the intertracheid water connection. Maldistribution of water was generally observed in the heartwood, and three types of water presence were distinguishable: a “wet area” with accumulated water, a “dry area” with little water, and a “moderate moisture area” with intermediate accumulation. The distribution pattern and amount of water in the heartwood varied dramatically among and even within trees. Separation of the heartwood from the sapwood in the intertracheid water connection suggested that the presence of water in the heartwood was caused by rewetting of the tracheid lamina that occurred after heartwood formation. The maldistribution of water in the heartwood suggested that a difference in the process of rewetting causes both uneven distribution and the various types of water presence.     

Acetaldehyde emission from wood induced by the addition of ethanol

A mechanism of acetaldehyde emission from wood induced by the addition of ethanol was proposed. It is known that acetaldehyde generation is due to the oxidation of ethanol via a metabolic process involving alcohol dehydrogenase (ADH) in living bodies. However, it remains unclear whether the enzymatic alcohol oxidation is applicable to wood. We investigated possible factors of wood parts, conditioning, storage sites, and heating and sterilization treatments on acetaldehyde emission using the syringe method and HPLC analysis. We reconfirmed that acetaldehyde emission was observed only when ethanol was added to wood. Greater acetaldehyde emissions were obtained in heartwood compared to sapwood in both Japanese cedar (Cryptomeria japonica D. Don) and Japanese cypress (Chamaecyparis obtusa Endl.) specimens. In addition, an acetaldehyde conversion rate of 1–2 mol% was determined in green cedar heartwood samples, while, conversely, air-dried cedar heartwood samples showed 4–5 mol%. Ethylene oxide gas sterilization had the effect of decreasing acetaldehyde emission on air-dried wood, but not on green wood. Autoclave sterilization could completely prevent acetaldehyde emissions from both green and air-dried wood. These results suggested that an original ADH in wood and an attached ADH from the outside via microorganisms onto wood were assumed to be the primary causes of acetaldehyde emissions from wood induced by the addition of ethanol.     

微生物对长白鱼鳞云杉木材渗透性的影响

本文利用水池贮存处理木材研究了细菌对改善长白鱼鳞云杉木材渗透性的有效性。渗透性的测定采用水上升置换气流法。试验结果表明,水池贮存处理长白鱼鳞云杉气干材10周,不仅可以非常显著地增加其边材的渗透性(渗透性平均增加29倍),而且其心材渗透性亦有明显改善(平均渗透性增加1.52倍)。但心材试样渗透性增加不均匀,仅有50％的心材试样在水池贮存处理后渗透性得到了增加。渗透性增加的原因主要是由于边材和部分心材试样受到短芽孢杆菌(Bacillus brevis)等细菌的侵蚀,据电镜观察,边材大多数具缘纹孔的纹孔塞被细菌降解后形成空洞,心材的管胞内壁及具缘纹孔的纹孔缘上有细菌存在。     

柚木种源生长和与材质有关特性的遗传变异及综合评价

对海南岛乐东尖峰岭27年生柚木6个种源的生长及与材质有关特性进行测定与分析,结果表明:种源间树皮厚度、心材宽度、基本密度差异极显著,树高、材积、枝下高、边材宽度差异显著,而胸径、边材年轮数及心材率差异不显著,说明在种源水平上对柚木进行生长和与材质有关特性的改良具有较大的潜力,尤其进行木材生长性状、基本密度和心材宽度的种...     

Resistance of Pinus leucodermis heartwood and sapwood against the brown-rot fungus Coniophora puteana

Abstract

This study assessed the decay resistance of Pinus leucodermis wood to the brown-rot fungus Coniophora puteana. Based upon the median weight losses of 30.65% for heartwood and of 34.68% for sapwood obtained in the biological tests, both the heartwood and sapwood material examined was classified as not durable (durability class 5) according to the CEN/TS 15083-1 classification. Total extractives were low, 3.93% in heartwood and 1.00% in sapwood, while lignin content was 22.60% and 25.41% in heartwood and sapwood, respectively. It is highly recommended to use protective treatments before using P. leucodermis wood in outdoor conditions.     

Separating Norway spruce heartwood and sapwood in dried condition with near-infrared spectroscopy and multivariate data analysis

Norway spruce [Picea abies (L.) Karst.] heartwood and sapwood have differing wood properties, but are similar in appearance. An investigation was made to see whether near-infrared spectroscopy (NIRS) could be used with multivariate statistics for separation between heartwood and sapwood in dry state on tangential longitudinal surfaces. For classification of wood into sapwood and heartwood, partial least square (PLS) regression was used. Orthogonal signal correction (OSC) filtering was used on the spectra. This study shows that a separation of sapwood and heartwood of spruce is possible with NIR spectra measured in a laboratory environment. The visible-wavelength spectra have significant influence on the predictive power of separation models between sapwood and heartwood of spruce. All 44 specimens in the calibration set were correctly classified into heartwood and sapwood. Validation of the model was done with a prediction set of 16 specimens, of which one was classified incorrectly.     

日本落叶松无性系木材性质的遗传变异

对10个10年生日本落叶松无性系的木材基本密度、管胞参数进行了测定.结果表明:木材基本密度,早、晚材管胞宽度和早材长宽比无性系间差异显著;木材基本密度,早、晚材管胞长度,早晚材管胞宽度和早晚材长宽比径向变异模式相似,即从髓心向外以曲线形式不断增加,有时亦有起伏;早材从髓心向外以近似直线的形式缓慢增加,晚材从髓心向外以曲线形式增加,初期增加幅度较大,到一定年龄后趋于水平变化并略有波动;材质性状与树木年轮间的关系以对数方程、幂函数方程、指数方程拟合效果较好;除了晚材壁腔比和早材壁厚外,其它木材性质的重复力均在0.5以上,受中度或中度以上的遗传制约,按照20%的选择率,长宽比和晚材管胞长能获得较高的遗传增益.     

针叶树材管胞气体渗透流阻及其渗透系数

针对树材气体渗透性与气体在管胞中的流动特性和规律紧密相关，研究管胞的气体渗透流阻，可以获得关于针叶树材气体渗透性更深入的认识。本文从针叶树材管胞解剖结构出发，运用流体力学理论，导出了管胞3个纹理方向渗透气体流阻的数学表达式，并由此计算了针叶树材管胞的气体渗透系数。计算结果表明，管胞流阻可以描述气体渗透阻力的分布情况，反映气体渗透性在3个纹理方向的差异，在木材细胞层次揭示针叶树材气体渗透性的机制。     

纹孔塞位置回弹对改善长白鱼鳞云杉木材渗透性作用初探

本文通过对难浸注的长白鱼鳞云杉气干5年心材进行水浸泡处理,探讨了纹孔塞位置可否回弹以提高木材渗透性的可能性。试验结果表明,气干5年长白鱼鳞云杉心材经水浸泡11周并用有机溶剂置换干燥后,平均气体渗透性增加了110%,但经成对比较试验t检验,以可靠性95%计差异不显著。表明气干5年后心材通过水浸泡处理,平均气体渗透性虽有增加,但偏移的纹孔塞可能并未重新回弹到中央位置使其渗透性获得真正的提高。     

Impregnation of radiata pine wood by vacuum treatment II: effect of pre-steaming on wood structure and resin content

Radiata pine sapwood and heartwood were dried using high-temperature, conventional-temperature, and air drying schedules with and without pre-steaming. They were then impregnated by vacuum treatment with double-distilled water, toluidine blue, and fluorescein dye. For sapwood, there were only minor differences in uptake between drying methods and when pre-steaming was used. Using microscopy, the primary flow pathways in sapwood were found to be the resin canal network and ray parenchyma cells, which provided conduction without large resistance. In heartwood, uptake was strongly influenced by pre-steaming the green lumber. After pre-steaming heart-wood, there was an increase in uptake from all surfaces but especially from the radial surfaces. Lower extractive contents, disruption of epithelial and ray parenchyma cells, and alteration of the condition of bordered pits were also associated with pre-steaming. It was therefore possible to classify flow paths in radiata pine heartwood five ways, according to uptake values and wood anatomical features.This research was presented in part at the 48th annual meeting of the Japan Wood Research Society, Shizuoka, April 1998.     

Dependence of shear strength on wood properties in cultivated Larix sibirica

Abstract

Mechanical properties are very important in structural uses of wood. In the case of larch wood, shear strength (SS) may be a limiting property, because the wood is brittle and it splinters easily. In this study, SS of Siberian larch (Larix sibirica) wood was studied in relation to its axial and radial location and to some other wood properties in the part of the trunk that produces logs of good carpentry quality. SS increased by 21–23% from the pith to the outer heartwood at each studied height (butt, 4.5 and 9 m), and it was at its most approximately 7% higher at the butt than at the other studied heights. The main reason for the radial increase in SS was the increase in density caused by wood maturation, but other factors also affected SS, depending on the grouping mode (combined material, radial/axial location). An exception was sapwood, for which no factors affecting SS could be identified. Thus, sapwood may behave differently from heartwood regarding use, even unexpectedly. The results suggest that mature heartwood, but not juvenile wood and sapwood, of Larix sibirica should primarily be used in products that require high SS.     

“I-214杨”心材、边材木质素的红外光谱、质子和碳-13核磁共振波谱特征研究

对从杨树心、边材提取的磨木木质素进行了元素分析和红外光谱（FTIR）质子和碳－13核磁共振波谱（^1H,^13C NMR)等化学特征研究。研究结果表明：杨树心、边材木质素的经验式分别为C9H7．16O2．38（OCH3）1．99和C9H8．61O2．73（OCH3）1．33。心材木质素甲氧基含量28．16％,比边材高8．73％。两种木质素均具有典型阔叶材的特征,化学结构类型基本一致,碳骨架结构基本相同,但化学官能团和键型的组成上存在差异。     

幼龄材范围的确定及树木生长速率对幼龄材生长量的影响

本文以杉木、日本落叶松的人上林和天然林木材为对象，选择ｙ＝ａ＋ｂｌｎｘ回归模式。利用其管胞特征因子随年轮数的变化，研究划分幼龄材年轮界限的最适因子，并就生长速率对幼龄材生长量的影响进入了探讨。结果表明：杉木和日本落叶松的人工林及天然林木的管胞特征值在径向水平上的变化均遵循ｙ＝ａ＋ｂｌｎｘ模式，尤其管胞长度与年轮数回归的相关系数Ｒ均达０．９８以上；管胞长度与管胞宽度及纤丝用相比，遗传率最大，随年轮数变化的模式最稳定，是划分幼龄材界限的最佳因子，由此得出杉木人工林幼龄材界限年轮为２０－２２（距髓心距离为１２．９－１３．２ｃｍ）、天然林为１６－１８（４．１－４．５ｃｍ），日本落叶松人工林为１９－２３（８．７－１０．５ｃｍ）、天然林为２３－２４（２．９－３．１ｃｍ）；幼龄材生长量与树木生长速率成正比。