In vitro biomechanical properties of 2 compression fixation methods for midbody proximal sesamoid bone fractures in horses

OBJECTIVE: To evaluate 2 methods of midbody proximal sesamoid bone repair--fixation by a screw placed in lag fashion and circumferential wire fixation--by comparing yield load and the adjacent soft-tissue strain during monotonic loading. STUDY DESIGN: Experimental study. SAMPLE POPULATION: 10 paired equine cadaver forelimbs from race-trained horses. METHODS: A transverse midbody osteotomy of the medial proximal sesamoid bone (PSB) was created. The osteotomy was repaired with a 4.5-mm cortex bone screw placed in lag fashion or a 1.25-mm circumferential wire. The limbs were instrumented with differential variable reluctance transducers placed in the suspensory apparatus and distal sesamoidean ligaments. The limbs were tested in axial compression in a single cycle until failure. RESULTS: The cortex bone screw repairs had a mean yield load of 2,908.2 N; 1 limb did not fail when tested to 5,000 N. All circumferential wire repairs failed with a mean yield load of 3,406.3 N. There was no statistical difference in mean yield load between the 2 repair methods. The maximum strain generated in the soft tissues attached to the proximal sesamoid bones was not significantly different between repair groups. CONCLUSIONS: All repaired limbs were able to withstand loads equal to those reportedly applied to the suspensory apparatus in vivo during walking. CLINICAL RELEVANCE: Each repair technique should have adequate yield strength for repair of midbody fractures of the PSB immediately after surgery.     

A biomechanical comparison of headless tapered variable pitch and AO cortical bone screws for fixation of a simulated slab fracture in equine third carpal bones

OBJECTIVE: To compare the mechanical shear strengths and stiffnesses obtained from in vitro testing of a simulated complete third carpal bone (C3) frontal plane radial facet slab fracture (osteotomy) stabilized with either a 4/5 Acutrak (AT) compression screw or a 4.5-mm AO cortical bone (AO) screw inserted in lag fashion. Drilling, tapping, and screw insertion torques, forces, and times also were compared between AT and AO implants. STUDY DESIGN: In vitro biomechanical assessment of site preparation, screw insertion, and shear failure test variables of bone screw stabilized simulated C3 slab fracture in paired cadaveric equine carpi. SAMPLE POPULATION: Eight pairs of cadaveric equine C3 without orthopedic abnormalities. METHODS: Standardized simulated C3 slab fractures were repaired with either AO or AT screws (AO/C3 and AT/C3 groups, respectively). Drilling, tapping, and screw insertion torques, forces, and times were measured with a materials testing machine for each screw type. Repaired specimens were tested in axially oriented shear until failure. Paired Students t-tests were used to assess differences between site preparation, screw insertion, and shear testing variables. Significance was set at P <.05. RESULTS: There were no significant differences in bone fragment measurements of the standardized simulated C3 slab fractures created for AO or AT screws. There were no significant differences for mean and maximum drilling torques; however, the tapered AT drill had greater maximum drilling force compared with the 3.2-mm and 4.5-mm AO drill bits. Mean insertion torque and force measured from the self-tapping AT screw were not significantly different compared with the 4.5-mm AO tap. There were no significant differences in maximum screw torque among constructs. Total procedure time was significantly longer for the AT group (5.8 +/- 1.6 minutes) compared with the AO group (2.9 +/- 1.1 minutes; P =.001). AT stabilized specimens had significantly greater mean +/- SD initial shear stiffness (3.64 +/- 1.08 kN/mm) than AO specimens (1.64 +/- 0.73 kN/mm; P =.005). All other shear mechanical testing variables were not statistically different among screw types. CONCLUSION: The 4/5 Acutrak insertion technique was accurate and safe, and the AT screw effectively stabilized simulated equine C3 frontal plane slab fractures. When tested in shear, this screw type was mechanically comparable to the 4.5-mm AO screw; however, AT constructs had greater initial shear stiffness. Initial shear stiffness was likely an indirect measure of interfragmentary compression, and thus may indicate that the AT screw provides a more rigid fixation for frontal plane C3 slab fractures in horses. CLINICAL RELEVANCE: Considering the comparable mechanical behavior, greater initial shear stiffness for AT screw stabilized C3 slab fracture fragments, the ability to accurately insert the screw with the aid of a guide pin, and the potential for less persistent soft tissue irritation with the headless screw design, the 4/5 tapered AT screw is an attractive alternative for repair of C3 slab fractures in horses.     

Effect of Gelatin Hydrogel Sheet Containing Basic Fibroblast Growth Factor on Proximal Sesamoid Bone Transverse Fracture Healing in the Horse

Our objective in this study was to examine the effect of gelatin hydrogel (GH) sheets containing basic fibroblast growth factor (bFGF) on healing of proximal sesamoid bone transverse fractures in the horse. Ten healthy adult Thoroughbreds were used. The lateral proximal sesamoid bone of the left forelimb and the medial proximal sesamoid bone of the right forelimb were osteotomized, while the horses were under general anesthesia, and subsequently repaired by lag screw fixation using a single 4.5-mm cortical screw. A GH sheet containing 100 μg of bFGF was then sutured to the synovial membrane adjacent to the osteotomized proximal sesamoid bone. In the control group, the fracture was fixed with a lag screw, and the articular capsule was sutured. Fracture healing was assessed by radiographic examination once a week for 16 weeks after the operation. Radiographic examination of bone healing revealed significantly lower demineralization of the fracture line in the GH sheet-treated group than in the control group. The rate of demineralization of the fracture line in the GH sheet-treated group was significantly lower than that in the control group at 2, 4, and 8 weeks after the operation. In this study, we demonstrated that the use of a GH sheet containing bFGF promotes healing of proximal sesamoid bone fracture in the horse. Therefore, it is believed that this treatment strategy would be useful for quick recovery from bone fracture in the horse.     

A biomechanical comparison of double-plate and Y-plate fixation for comminuted equine second phalangeal fractures

OBJECTIVES: To compare the biomechanical properties, in full limb preparations, of intact second phalanx and a simulated comminuted second phalangeal fracture stabilized with either two bone plates or a custom Y-plate. STUDY DESIGN: In vitro biomechanical assessment of intact limbs and of paired limbs with a simulated second phalangeal fracture stabilized by one of two fixation methods. Animal Population-Thirteen pairs of equine cadaveric forelimbs. METHODS: A comminuted second phalangeal fracture was created in six paired cadaveric limbs. For each limb pair, the fracture was stabilized with two plates in one limb, and with a Y-plate in the contralateral limb. These limbs and seven pairs of intact limbs were subjected to axial compression in a single cycle until failure. Mechanical properties were compared with a mixed-model ANOVA and post hoc contrasts. Joint contact pressure, screw insertion torque, and final screw torque remaining after mechanical testing were also evaluated for constructs. RESULTS: No significant differences in mechanical testing variables were detected between construct types. However, the Y-Plate construct had significantly greater yield load, yield displacement and yield energy, and failure load and stiffness values than those for intact specimens, whereas the double-plate construct only had greater stiffness than intact specimens. There were no significant differences in joint contact pressures for both constructs. The final screw torque for proximal phalangeal screws was significantly greater for the Y-plate constructs than for double-plate constructs. CONCLUSIONS: The Y-plate was as effective as the double-plate technique for stabilization of simulated comminuted second phalangeal fractures in monotonically tested equine cadaveric forelimbs. CLINICAL RELEVANCE: This investigation supports evaluation of the Y-plate for repair of comminuted second phalangeal fractures in equine patients. Its specific design may facilitate repair of second phalangeal fractures, and may provide increased stability by allowing the proximal fragments of the second phalanx to be fixed with three screws placed through the plate.     

A comparison of ultra-high-molecular weight polyethylene cable and stainless steel wire using two fixation techniques for repair of equine midbody sesamoid fractures: an in vitro biomechanical study

OBJECTIVE: To compare the monotonic tensile and fatigue strength of 16-gauge stainless steel wire (SSW) to ultra-high-molecular weight polyethylene (UHMWPE) cable using a transfixed cerclage technique in an in vitro midbody sesamoid osteotomy model. Endoscopic modifications to Martins transfixed cerclage technique were developed. A new suture technique of fixation was compared with the transfixed cerclage technique by measuring gap formation after cyclic testing. STUDY DESIGN: An in vitro biomechanical paired equine cadaver limb study. SAMPLE POPULATION: Twenty-one paired cadaveric adult equine forelimbs. METHODS: Uniaxial medial midbody sesamoid osteotomies were created in paired adult equine forelimbs. Monotonic tensile strength was measured on 10 forelimbs repaired by a transfixed cerclage technique using wire or cable. Fatigue testing to failure was performed on 4 forelimbs repaired using the transfixed cerclage technique by cycling the limbs between 500 N and 2,000 N. The limbs were initially repaired with wire, cycled until the wire broke, then repaired with cable and cycled again to failure. Fatigue testing for gap displacement was performed on 8 limbs repaired with either the transfixed cerclage technique or the suture technique. Limbs were cycled between 500 N and 2,000 N for 10,000 cycles. The limbs were repaired with wire initially, tested, and then repaired with cable and tested again. Twenty-two limbs were used for mechanical testing. The remaining limbs (20) were used to develop and practice the endoscopic transfixed cerclage (10 limbs) and suture (10 limbs) techniques. RESULTS: Ultimate tensile strength (UTS) of UHMWPE cable constructs was 34% greater than the UTS of SSW constructs. Fatigue strength was 2 to 20 times greater for UHMWPE cable constructs than SSW constructs. Separation of fragments was 153% less for limbs repaired by the suture technique compared with those repaired by the transfixed cerclage technique. CONCLUSIONS: UHMWPE cable shows promise for this clinical application because of its greater tensile and fatigue strength. The newly described suture technique significantly reduced gap formation compared with the transfixed cerclage technique. Osteotomy gap formation occurred early in cycling, suggesting that rigid support in the form of a cast may be needed during the early postoperative period for wiring techniques. CLINICAL RELEVANCE: Clinical testing of UHMWPE cable should eliminate problems of wire breakage seen with SSW. The endoscopic transfixed cerclage technique can be used by surgeons familiar with arthroscopic surgery. However, the suture technique needs to be tested in vivo to determine whether there is a clinical advantage compared with the transfixed cerclage technique.     

An In Vitro Biomechanical Comparison of Two Fixation Methods for Transverse Osteotomies of the Medial Proximal Forelimb Sesamoid Bones in Horses

OBJECTIVE: This study compared the mechanical properties of the normal intact suspensory apparatus and two methods of fixation for repair of transverse, midbody fractures of the proximal sesamoid bones of adult horses: transfixation wiring (TW) and screws placed in lag fashion (LS). STUDY DESIGN: An in vitro, paired study using equine cadaver limbs mounted in a loading apparatus was used to test the mechanical properties of TW and LS. ANIMAL OR SAMPLE POPULATION: Seventeen paired (13 repaired, 4 normal) equine cadaver limbs consisting of the suspensory apparatus third metacarpal bone, and first and second phalanges. METHOD: The two methods of repair and normal intact specimens were evaluated in single cycle-to-failure loading. Yield failure was defined to occur at the first notable discontinuity (>50 N) in the load-displacement curve, the first visible failure as evident on the videotape, or a change in the slope of the moment-fetlock angle curve. Ultimate failure was defined to occur at the highest load resisted by the specimen. Corresponding resultant force and force per kg of body weight on the suspensory apparatus, fetlock joint moment, and angle of fetlock dorsiflexion were calculated by use of specimen dimensions and applied load. These were compared along with specimen stiffness, and ram displacement. RESULTS: Load on the suspensory apparatus, load on the suspensory apparatus per kg of body weight, moment, applied load, and angle of fetlock dorsiflexion at yield failure were significantly greater for the TW-repaired than for the LS-repaired specimens. A 3 to 5 mm gap was observed before yield failure in most TW-repaired osteotomies. CONCLUSIONS: Transfixation wiring provided greater strength to yield failure than screws placed in lag fashion in single cycle load-to-failure mechanical testing of repaired transverse osteotomized specimens of the medial proximal forelimb sesamoid bone.     

Lag screw and cancellous bone graft fixation of transverse proximal sesamoid bone fractures in horses: 25 cases (1983-1989).

Case records of 25 horses with transverse fractures of the proximal sesamoid bone were reviewed to evaluate the success of treatment. All fractures were repaired by use of lag screw fixation and an autogenous cancellous bone graft because the fracture fragments were considered too large for surgical removal and reconstruction of the suspensory apparatus was necessary. Radiography was performed in all cases, and the fractures were classified into 3 types: (1) proximal midbody fractures, which included all fractures in the proximal aspect of the sesamoid bone that resulted in fragments involving greater than one third but less than one half of the total mass of the sesamoid bone; (2) midbody fractures that divided the bone into 2 equal portions; and (3) distal midbody fractures, which included transverse fractures in the distal aspect of the sesamoid bone that resulted in fragments involving greater than one third but less than one half of the total mass of the sesamoid bone. Of these cases, race records were obtained for 9 Standardbreds and 5 Thoroughbreds. Postoperative performance criteria evaluated were the ability to train and start 1 race, ability to maintain preinjury class of racing, earnings per start, and the number of starts following surgery. In Thoroughbreds, fractures occurred most commonly in the right forelimb; in Standardbreds, the left hind limb was most commonly involved. The midbody fracture was the most common type in both breeds, and the distribution of fracture location within the sesamoid bone was similar for both breeds.(ABSTRACT TRUNCATED AT 250 WORDS)     

A biomechanical comparison of equine third metacarpal condylar bone fragment compression and screw pushout strength between headless tapered variable pitch and AO cortical bone screws

OBJECTIVES: To compare bone fragment compression and the mechanical pushout strength and stiffness of 6.5-mm Acutrak Plus (AP) and 4.5-mm AO cortical (AO) bone screws after stabilization of a simulated equine third metacarpal (MC3) bone complete lateral condylar fracture. STUDY DESIGN: In vitro biomechanical paired study of screw insertion variables, bone fragment compression, and screw pushout tests using a bone screw stabilized simulated lateral condylar fracture model. SAMPLE POPULATION: Six pairs of cadaveric equine MC3s. METHODS: Metacarpi were placed in a fixture and centered on a biaxial load cell in a materials testing system to measure torque, compressive force, and time for drilling, tapping, and screw insertion. Fragment compression was measured with a pressure-sensing device placed between the simulated fracture fragments during screw insertion for fragment stabilization. Subsequently, screws were pushed out of the stabilized bone fragments in a single cycle to failure. A paired t test was used to assess differences between site preparation, screw insertion, fragment compression, and screw pushout variables, with significance set at P <.05. RESULTS: Measured drilling variables were comparable for AO and AP specimens. However, the AP tap had significantly greater insertion torque and force. Mean maximum screw insertion torque was significantly greater for AO screws. For fragment compression, AP screws generated 65% and 44% of the compressive pressure and force, respectively, of AO screws. AP screws tended to have higher overall pushout strength. Pushout stiffness was similar between both screw types. CONCLUSION: The 6.5-mm tapered AP screw generated less interfragmentary compressive pressure and force but had similar pushout stiffness. Evaluation of failure patterns demonstrated that AP screws had greater pushout strength compared with 4.5-mm AO screws for fixation of a simulated complete lateral condylar fracture. CLINICAL RELEVANCE: The 6.5-mm tapered AP screw should provide ample holding strength but would provide less interfragmentary compression than 4.5-mm AO screws for repair of complete lateral condylar fractures in horses.     

A Biomechanical Comparison of Headless Tapered Variable Pitch and AO Cortical Bone Screws for Fixation of a Simulated Lateral Condylar Fracture in Equine Third Metacarpal Bones

OBJECTIVE: To compare drilling, tapping, and screw-insertion torque, force, and time for the 4.5-mm AO and 6.5-mm Acutrak Plus (AP) bone screws, and to compare the mechanical shear strength and stiffness of a simulated complete lateral condylar fracture of the equine third metacarpal bone (MC3) stabilized with either an AO or AP screw. STUDY DESIGN: In vitro biomechanical assessment of screw-insertion variables, and shear failure tests of a bone-screw-stabilized simulated lateral condylar fracture. SAMPLE POPULATION: Eight pairs of cadaveric equine MC3s METHODS: Metacarpi were placed in a fixture and centered on a biaxial load cell in a materials-testing system to measure torque, compressive force, and time for drilling, tapping, and screw insertion. Standardized simulated lateral condylar fractures were stabilized by either an AO or AP screw and tested in shear until failure. A paired t test was used to assess differences between screws, with significance set at P < .05. RESULTS: Insertion and mechanical shear testing variables were comparable for AO and AP insertion equipment and screws. CONCLUSION: The 6.5-mm tapered AP screw can be inserted in equine third metacarpal condyles and is mechanically comparable with the 4.5-mm AO screw for fixation of a simulated lateral condylar fracture. CLINICAL RELEVANCE: Considering the comparable mechanical behavior, the potential for less-persistent soft-tissue irritation with the headless design, and the ability to achieve interfragmentary compression by inserting the screw in one hole drilled perpendicular to the fracture plane, the 6.5-mm tapered AP screw may be an attractive alternative for repair of incomplete lateral condylar fractures in horses.     

An In Vitro Biomechanical Comparison of Dynamic Condylar Screw Plate Combined with a Dorsal Plate and Double Plate Fixation of Distal Diaphyseal Radial Osteotomies in Adult Horses

Objective— To compare stiffness and strength of a dynamic condylar screw plate combined with dorsal broad dynamic compression plate (DCS–bDCP) fixation with double broad dynamic compression plate (dbDCP) fixation used to repair oblique distal fractures of adult equine radii. Study Design— Experimental. Sample Population— Adult equine radii (n=10 pair). Methods— An unconstrained three‐dimensional loading–measurement system was used to determine stiffness of a 50 mm long intact, and then DCS–bDCP or dbDCP‐plated osteotomized/ostectomized segment of radii when subjected to a nondestructive sequence of compression, torsion, and lateral‐to‐medial (LM), medial‐to‐lateral (ML), cranial‐to‐caudal (CrCa), and caudal‐to‐cranial (CaCr) bending. Uniform load over the entire length of construct identified its weakest characteristics during torsion and LM and CrCa bending to failure. Results— No difference was observed between osteotomized/ostectomized DCS–bDCP and dbDCP construct stiffness for all 6 loading modes, and strength for all 3 failure loads. Ostectomized DCS–bDCP and dbDCP construct stiffness was significantly lower than osteotomized radii, the latter approaching intact for axial, LM, and CrCa bending. Most frequent failure was bone fracture through exit site of a screw located adjacent to osteotomy/ostectomy. Conclusions— DCS–DCP and dbDCP constructs had comparable strength and stiffness when repairing osteotomies/ostectomies in equine adult radius bone. Fracture reduction increased stiffness that approached intact bone for loads that placed the unplated side in compression. Clinical Relevance— DCS–bDCP and dbDCP constructs are comparable in stiffness and strength when applied to oblique distal diaphyseal osteotomies/ostectomies in equine radius bone. However, the DCS's localized effect on distal epiphyseal structure because of additional bone removal remains to be investigated under in vivo articular loading conditions.     

Morphologic Radiographic Study of the Proximal Sesamoid Bones of the Forelimb in Thoroughbred Racehorses in Training

The aim of this study was to identify differences in bone shape (height and width) of proximal sesamoid bones (PSB) in 2‐year‐old Thoroughbred racehorses in training. Dorsal 15° proximal‐palmarodistal oblique images of each metacarpophalangeal joint were acquired before the horses started training and at 1 year after the start of exercise and racing. There were no changes in height and width of PSBs induced by training. There was a significant difference of height and width between medial and lateral PSBs. In both forelimbs, the medial PSB was significantly wider and shorter than the lateral PSB. The medial PSB of the right forelimb was significantly wider than that of the left forelimb. These results might explain some limb predilection for fracture of PSBs. The difference in strain pattern between medial and lateral PSBs in different loading conditions needs to be investigated.     

Risk factors for proximal sesamoid bone fractures associated with exercise history and horseshoe characteristics in Thoroughbred racehorses

OBJECTIVE: To assess individual and combined associations of high-speed exercise and horseshoe characteristics with risk of forelimb proximal sesamoid bone fractures and proximal sesamoid bone midbody fractures in Thoroughbred racehorses. ANIMALS: 269 deceased Thoroughbred racehorses. PROCEDURES: A case-control study design was used to compare 121 horses with a fracture of at least 1 of 4 forelimb proximal sesamoid bones (75 horses had a midbody fracture) and 148 horses without a forelimb proximal sesamoid bone fracture. Univariable and multivariable logistic regression analyses were used to evaluate potential risk factors for association with proximal sesamoid bone fracture. RESULTS: Compared with horses that died without proximal sesamoid bone fractures, horses that died with proximal sesamoid bone fractures were more likely to be sexually intact males, spend more time in active trainingand racing, complete more events, train and race longer since their last layup, have higher exercise intensities during the 12 months prior to death, and have greater cumulative distances for their career. Horses with proximal sesamoid bone midbody fractures were more likely to be sexually intact males, train and race longer since their last layup, and have higher exercise intensities during the 12 months prior to death. CONCLUSIONS AND CLINICAL RELEVANCE: Limitingexercise intensity and the continuous time spent in activity duringa horse's career may decrease the frequency of forelimb proximal sesamoid bone fractures in Thoroughbred horses.     

An in vitro biomechanical comparison between prototype tapered shaft cortical bone screws and AO cortical bone screws for an equine metacarpal dynamic compression plate fixation of osteotomized equine third metacarpal bones

OBJECTIVES: To compare biomechanical properties of a prototype 5.5 mm tapered shaft cortical screw (TSS) and 5.5 mm AO cortical screw for an equine third metacarpal dynamic compression plate (EM-DCP) fixation to repair osteotomized equine third metacarpal (MC3) bones. STUDY DESIGN: Paired in vitro biomechanical testing of cadaveric equine MC3 with a mid-diaphyseal osteotomy, stabilized by 1 of 2 methods for fracture fixation. ANIMAL POPULATION: Adult equine cadaveric MC3 bones (n=12 pairs). METHODS: Twelve pairs of equine MC3 were divided into 3 groups (4 pairs each) for (1) 4-point bending single cycle to failure testing, (2) 4-point bending cyclic fatigue testing, and (3) torsional single cycle to failure testing. An EM-DCP (10-hole, 4.5 mm) was applied to the dorsal surface of each, mid-diaphyseal osteotomized, MC3 pair. For each MC3 bone pair, 1 was randomly chosen to have the EM-DCP secured with four 5.5 mm TSS (2 screws proximal and distal to the osteotomy; TSS construct), two 5.5 mm AO cortical screws (most proximal and distal holes in the plate) and four 4.5 mm AO cortical screws in the remaining holes. The control construct (AO construct) had four 5.5 mm AO cortical screws to secure the EM-DCP in the 2 holes proximal and distal to the osteotomy in the contralateral bone from each pair. The remaining holes of the EM-DCP were filled with two 5.5 mm AO cortical screws (most proximal and distal holes in the plate) and four 4.5 mm AO cortical screws. All plates and screws were applied using standard AO/ASIF techniques. Mean test variable values for each method were compared using a paired t-test within each group. Significance was set at P<.05. RESULTS: Mean 4-point bending yield load, yield bending moment, bending composite rigidity, failure load and failure bending moment of the TSS construct were significantly greater (P<.00004 for yield and P<.00001 for failure loads) than those of the AO construct. Mean cycles to failure in 4-point bending of the TSS construct was significantly greater (P<.0002) than that of the AO construct. The mean yield load and composite rigidity in torsion of the TSS construct were significantly greater (P<.0039 and P<.00003, respectively) than that of the AO construct. CONCLUSION: The TSS construct provides increased stability in both static overload testing and cyclic fatigue testing. CLINICAL RELEVANCE: The results of this in vitro study support the conclusion that the EM-DCP fixation using the prototype 5.5 mm TSS is biomechanically superior to the EM-DCP fixation using 5.5 mm AO cortical screws for the stabilization of osteotomized equine MC3.     

Biomechanical Comparison of the Herbert and AO Cortical Bone Screws for Compression of an Equine Third Carpal Bone Dorsal Plane Slab Osteotomy

Objective—To assess feasibility of insertion of 4.5-mm Herbert cannulated bone screws (HS) using fluoroscopic guidance and compare the mechanical shear strength of these HS and 4.5-mm AO cortical bone screws (AO) for fixation of dorsal plane slab osteotomies in equine cadaver third carpal bones (C3).
Animals or Sample Population—Eight equine cadavers.
Methods—Bone mineral composition and density of contralateral C3 were confirmed to be equivalent using dual-energy x-ray absorptiometry. A standard 10-mm C3 slab osteotomy was reduced using HS or AO instrumentation under fluoroscopic guidance. Specimens were loaded in shear until failure, using a materials testing apparatus.
Results—HS and AO instrumentation allowed accurate reconstruction of the osteotomy, but there was difficulty encountered seating the HS proximal self-tapping threads. There was no significant difference in maximal load to failure, stiffness, or mode of failure of constructs created with the HS and AO screws.
Conclusions —Use of 4.5-mm HS for repair of C3 radial facet, dorsal plane slab fractures may result in a mechanically comparable fixation to a repair using a 4.5-mm AO. Equine dorsal C3 may be too dense, however, to allow placement of the proximal self-tapping threads of the HS without potentially excessive application of torque to the screw itself.
Clinical Relevance —Dorsal plane, radial facet slab fractures of the equine C3 are a significant clinical problem. Accurate reconstruction and stabilization are necessary for return to athletic function.     

Surgical Repair of Mid‐body Proximal Sesamoid Bone Fractures in 25 Horses

Objective— To describe the characteristics of unilateral mid‐body proximal sesamoid bone (PSB) fractures, to determine factors associated with the outcome of horses after surgical repair, and to describe a technique for arthroscopically assisted screw fixation in lag fashion. Study Design— Retrospective case series. Animals— Horses (n=25) with unilateral mid‐body PSB fracture. Methods— Medical records (1996–2006), radiographs, and arthroscopic videos of horses with surgically repaired unilateral mid‐body PSB fractures were reviewed. Retrieved data included signalment, affected limb and PSB, fracture characteristics, and surgical technique. Outcome was established by radiographic assessment of healing and race records; categorical data were analyzed using Fisher's Exact test. Results— Medial forelimb PSBs were most commonly affected (80%). Surgical technique and degree of reduction were significantly associated with outcome; 44% of horses with screw repair and none of the horses with wire fixation raced (P=.047). Factors that may have influenced this outcome were differences in fracture reduction (improved reduction in 22% wire repairs and 88% screw repairs, P=.002) and use of external coaptation (22% wire repair and 88% lag screw repair, P=.002). None of the horses with unimproved reduction raced after surgery. Conclusions— Only 28% of horses with mid‐body PSB fractures raced after surgery. Compared with wire fixation, screw fixation in lag fashion resulted in good reduction and is seemingly a superior repair technique. Clinical Relevance— For mid‐body PSB fractures, arthroscopically assisted screw fixation in lag fashion and external coaptation for anesthesia recovery and initial support provides the best likelihood of return to athletic use.     

An in vitro biomechanical comparison of equine proximal interphalangeal joint arthrodesis techniques: two parallel transarticular headless tapered variable pitch screws versus two parallel transarticular AO cortical bone screws inserted in lag fashion

Objectives: To compare the mean number of cycles to failure under axial compression of equine proximal interphalangeal (PIP) joint arthrodesis constructs created by 2 parallel transarticular Acutrak Plus screws (AP‐TS) or 2 parallel transarticular 5.5 mm cortical screws inserted in lag fashion (AO‐TLS). Study Design: Paired in vitro biomechanical testing of 2 methods of stabilizing cadaveric adult equine forelimb PIP joints. Sample Population: Cadaveric adult equine forelimbs (n=5 pairs). Methods: For each forelimb pair, 1 PIP joint was stabilized with AP‐TS and 1 with AP‐TLS. The 5 construct pairs were tested for cyclic fatigue under axial compression. Mean number of cycles to failure for each fixation method were compared by a paired t‐test within each group with statistical significance set at P<.05. Results: The mean number of cycles to failure under axial compression for AO‐TLS fixation and AP‐TS fixation were 57,723±8488 and 35,322±4698, respectively. Conclusion: The AO‐TLS was superior to the AP‐TS in resisting cyclic fatigue under axial compression.     

Comparison of insertion time and pullout strength between self-tapping and non-self-tapping AO 4.5-mm cortical bone screws in adult equine third metacarpal bone

OBJECTIVE: To compare screw insertion characteristics and pullout mechanical properties between self-tapping (ST) and non-self-tapping (NST) AO 4.5-mm cortical bone screws in adult equine third metacarpal bone (MC3). STUDY DESIGN: In vitro biomechanical experiment. ANIMALS OR SAMPLE POPULATION: Seven pairs of adult equine MC3. METHODS: Bicortical holes were drilled transversely in proximal metaphyseal, diaphyseal, and distal metaphyseal locations of paired MC3. NST screws were inserted in pre-tapped holes in 3 sites of one bone pair, and ST screws were inserted in non-tapped holes of contralateral MC3. Tapping and screw insertion times and maximum torques were measured. Screw pullout mechanical properties were determined. RESULTS: Screw insertion time was longer for ST screws. Total time for tapping and insertion (total insertion time) was over twice as long for NST screws. Statistically significant differences were not observed between screws for any pullout mechanical property. From pullout tests, diaphyseal locations had significantly stiffer and stronger structure than metaphyseal locations. Pullout failure more commonly occurred because of screw breakage than bone failure. Bone failure and bone comminution were more commonly associated with ST screws. Bone failure sites had pullout failure loads that were 90% of screw failure sites. CONCLUSIONS: NST and ST 4.5-mm-diameter cortical bone screws have similar pullout mechanical properties from adult equine MC3. ST screws require less than half the total insertion time of NST screws. CLINICAL RELEVANCE: Use of ST 4.5-mm-diameter cortical bone screws should be considered for repair of adult equine MC3 fractures; however, bone failures at screw sites should be monitored.     

Computed tomography to identify preoperative guidelines for internal fixation of the distal sesamoid bone in horses: an in vitro study

Objective: To assess the reliability of computed tomography (CT) to identify the direction of implant insertion for cortical screws along the longitudinal axis of intact (nonfractured) distal sesamoid bones. Study Design: In vitro study. Sample Population: Cadaveric paired equine forelimbs (n=16). Methods: Insertion of a cortical screw in lag fashion along the longitudinal axis of intact (nonfractured) distal sesamoid bones was evaluated in 2 groups (3.5 and 4.5 mm) of 8 paired limbs. In each group, the direction of the distal sesamoid bone was determined by CT (Equine XTC 3000 pQCT scanner). Screw placement was verified by specimen dissection. Implant direction was considered satisfactory if the entire screw length was within the distal sesamoid bone and not damaging the articular or flexural surfaces. Results: In our sample and according to our criteria, the proportion of satisfactory direction of screws was 0.63 (5/8) for 4.5 mm implants, and 0.87 (7/8) for 3.5 mm implants. Conclusions: CT is a useful imaging modality to identify anatomic landmarks for insertion of a 3.5 mm cortical screw in the distal sesamoid bone.     

Limb loading activity of adult horses confined to box stalls in an equine hospital barn

OBJECTIVE: To determine a range of limb loading activity for healthy adult horses confined to box stalls in an equine veterinary teaching hospital and determine the effects of hospital environmental factors on load rates and daily limb loading patterns. ANIMALS: 6 mature healthy horses of various ages, breeds, and sexes, and 1 horse with a repaired metatarsal fracture. PROCEDURE: Step monitors were placed on 2 limbs of adult horses confined to box stalls. Relocation steps and weight shifts were recorded, as loading events, for 24 hours. Influence of forelimb versus hind limb and environmental factors on load rate (loading events per hour) were assessed with repeated-measures ANOVA. RESULTS: Loading activity was greater for the forelimb than the hind limb and was greater during the day than the night. Loading activity differences were not associated with daytime environmental factors. CONCLUSIONS AND CLINICAL RELEVANCE: Horses with normal locomotor activity appear to have higher load rates for forelimbs compared with hind limbs and higher load rates during the day compared with night. Knowledge of influence of environmental factors and mechanical restraint on limb loading activity may be useful in management of horses with musculoskeletal disorders. This information may also be used for in vitro simulation of in vivo loading of limbs during cyclic biomechanical investigations.     

Gross anatomy,computed tomography,magnetic resonance imaging and bone mineral densitometry of the ovine metacarpo/metatarsophalangeal joint

This study was aimed to provide anatomical atlas of the ovine metacarpo/metatarsophalangeal joints using computed tomography (CT) scan and magnetic resonance imaging (MRI), as well as to investigate bone mineral density (BMD) and morphometric features of this joint. The limbs of twenty adult Sanjabi sheep were examined. Imaging was performed using a 16-slice multi-detector CT scanner and a 1.5 Tesla MRI scanner. The obtained images were correlated with corresponding anatomical sections. BMD was measured by Dual Energy X-ray Absorptiometry (DEXA) method. Also morphometric features included distance between metacarpal and metatarsal heads, width of metacarpal and metatarsal head, length, width and the height of the proximal sesamoid bones were measured. In MRI images, compact bones, ligaments and tendons showed less signal intensity (hypointense). The fatty tissue and bone marrow had more signal intensity (hyperintense), but articular cartilage and synovial fluid showed moderate signal intensity. BMD in the left hind limb was significantly higher than other three limbs (p ≤ 0.05). The length of proximal sesamoid bones in left forelimb was higher than right forelimb (p ≤ 0.05). The thickness of proximal sesamoid bones in left limbs was higher than those in their counterparts (p ≤ 0.05). The width of the medial head in the forelimbs was significantly greater than the hind limbs (p ≤ 0.05). The present results might be useful in managing the clinical techniques on this joint. Larger volume of the proximal sesamoid bones and wider medial head in the forelimbs compared to the hindlimbs impel this speculation that the centre of gravity is closer to the forelimbs.