Preparation of TiO<Subscript>2</Subscript>-coated ZnO Nanoparticles and Their Effect on the UV Absorption of a Poly(vinyl alcohol) Composite Film

Titanium oxide (TiO₂) and zinc oxide (ZnO) composite structured nanoparticles were prepared by combining a sol-gel process and a solvothermal method. Titanium (IV) isoproxide (TTIP), used as a TiO₂ precursor, was dissolved in a colloidal ZnO nanoparticle solution synthesized by the sol-gel method, and TiO₂ was synthesized via solvothermal synthesis onto the ZnO nanoparticles. The effects of reaction conditions such as pH, reaction temperature, and reaction time on the morphology of the composite nanoparticles and the ultraviolet (UV) absorbance of their polymer composite films were investigated. The UV absorption of the poly(vinyl alcohol) (PVA) composite film with TiO₂-coated ZnO nanoparticles was higher than that of the TiO₂, ZnO, and ZnO-coated TiO₂ composite films. The reaction pH was found to have the strongest influence on the UV absorbance of the PVA/(TiO₂/ZnO) composite film. A pH of 7.0, reaction temperature of 250 °C, and reaction time of 24 h were the optimum conditions for UV absorption.     

Fabrication and characterization of nano Al<Subscript>2</Subscript>O<Subscript>3</Subscript> filled PVA:NH<Subscript>4</Subscript>SCN electrolyte nanofibers by electrospinning

Present paper reports a method of preparing polymer composite electrolyte nanofiber mat using polyvinyl alcohol (PVA), ammonium thiocynate (NH₄SCN) salt, and aluminium oxide (Al₂O₃) nano particles based on electrospinning technique. Two-stage process of preparation of nanofibers, namely, preparation of nano particles filled PVA electrolyte gel solution followed by its electrospinning has been used. The so obtained nanofibers have been characterized by XRD, DSC, SEM, and Conductivity measurements. XRD patterns affirm the formation of nanocomposite while SEM pictures reveal formation of fibers on a nano scale format (300–800 nm). Fibers of the electrolytes are seen to be thermally stable. Ionic conductivity of electrolyte fiber is seen to improve in the presence of nano filler at room temperature with a maximum at 5.31×10⁻³ Scm⁻¹ for 4 wt% filler concentration, which is comparable to that for corresponding dried gel electrolyte films.     

Water vapor transport parameters of a cast wheat gluten film

Understanding the mode of transport of water vapor through the film is important for improving the moisture barrier properties of wheat gluten (WG) films. Effective permeability (P_eff), solubility (S_eff), and diffusion (D_eff) coefficients of a hydrophilic cast WG film were determined at 25°C within the relative humidity (RH) range of 0–84% (with a 9–13% RH gradient between upstream and downstream water vapor flux). P_eff, S_eff, and D_eff increased substantially as the RH gradient moved upwards in the RH spectrum. P_eff increased by four orders of magnitude from the lowest RH condition of 0–11% (3.8×10⁻¹¹ g·m/m²·s·Pa) to the highest RH condition of 75–84% (4.1×10⁻⁷ g·m/m²·s·Pa). A moisture sorption isotherm of the film at 25°C was constructed. Both the Guggenheim–Anderson–DeBoer (GAB) and the Kuhn moisture sorption isotherm models showed a good fit to the experimental adsorption data. Testing of WG films at the expected conditions of actual use is necessary to quantify the water vapor permeation through the films.     

Thermal time requirements for the development of green pea (Pisum sativum L.)

The purpose of this investigation was to quantify, for crop modelling purposes, temperature response functions of various developmental stages of several green pea (Pisum sativum L.) cultivars. Cardinal temperatures, namely the base (T_b), optimum (T_m) and maximum temperature (T_x), for various developmental stages, were also determined. Below T_b and above T_x, development rates were zero and at T_m development proceeded at the maximum rate. Developmental stages were monitored in both controlled environments and field trials. No significant differences were found between cultivars regarding optimum temperatures for 50% germination. A T_b of 0°C, T_m of 29°C and T_x of 40°C for germination represents a good summary of the results. For the emergence, vegetative and reproductive stages, a T_b of 3°C, T_m of 28°C and T_x value of 38°C are appropriate. In the field, the crops required approximately 100°C d for emergence, 260°C d to reach the four-leaf stage, 380°C d till the seven-leaf stage and 730°C d to reach the 14-leaf stage. Thermal time requirements from sowing to flowering ranged from 770°C d to 890°C d for different cultivars, and from sowing to maturity (tenderometer reading of 130) from 1370°C d to 1450°C d.     

Microstructures and electrical properties of composite films based on carbon nanotube and para-aramid containing cyano side group

We report the microstructures and electrical properties of poly(2-cyano-1,4-phenylene terephthalamide) (cyPPTA)-based composite films including pristine multi-walled carbon nanotube (MWCNT) of 0.3-10.0 wt%, which were manufactured by ultrasonication-based solution mixing and casting techniques. FT-IR spectra of the composite films revealed the existence of specific interaction between cyPPTA and MWCNT. Accordingly, the pristine MWCNTs were found to be dispersed uniformly in the cyPPTA matrix, as confirmed by TEM images. The electrical resistivity of the composite films decreased considerably from ~10¹⁰ Ω cm to ~10⁰ Ω cm with the increase of the MWCNT content by forming a conductive percolation threshold at ~0.525 wt%. The composite films with 3.0-10.0 wt% MWCNT contents, which have sufficiently low electrical resistivity of ~10²-10⁰ Ω cm, exhibited excellent electric heating performance by attaining high maximum temperatures and electric power efficiency under given applied voltages of 10-100 V. Since the thermal decomposition of the composite films took place at 520-600 °C under air atmosphere, cyPPTA/MWCNT composite films could be used for high performance electric heating, antistatic, and EMI shielding materials.     

Thermal requirements for barley maturation and leaf development in interior Alaska

Spring barley (Hordeum vulgare L.) is well adapted to the cool and short growing season of interior Alaska but little is known about thermal requirements for development and maturation of barley at such latitudes. Air temperature and barley development were monitored over the course of six growing seasons at Fairbanks (65°N) and Delta Junction (64°N), Alaska. These data were used to assess the base temperature (T_b) in the linear, thermal-unit model using the least variable, x-intercept, and regression coefficient methods. These methods indicated a range in T_b from 0°C to 1.5°C. At a T_b of 0°C, barley required nearly 1100°C d to mature. The phyllochron differed between early and late sowings and averaged 75°C d leaf⁻¹. Sowing date appeared to influence the phyllochron during early vegetative growth due to differences in daylength as well as temperature.     

Immobilization of Cationic Titanium Dioxide (TiO<Subscript>2</Subscript><Superscript>+</Superscript>) on Electrospun Nanofibrous Mat: Synthesis,Characterization, and Potential Environmental Application

We report a facile approach to fabrication and characterization of cationic titanium dioxide (TiO₂⁺) on poly (vinyl alcohol)/poly (acrylic acid) (PVA/PAA) composite electro-spun nanofibrous mat. The aim of this study is to develop a “functional electrospun nanofibrous mat” as a sustainable approach to superior photocatalytic degradation of organic colorants. For that, the PVA/PAA nanofibrous mat was prepared by electrospinning of PVA and PAA solution according to an aspect ratio of 1:1 and later water stability was induced by the thermal cross linking at an elevated temperature of 145 °C for 30 minute. By means of electrostatic layer-by-layer (LbL) assembly, cationic titanium dioxide (TiO₂⁺, ~19 nm) was immobilized on the surface of the water stable nanofibrous mat. As functionalized composited nanofibrous mat was characterized by using scanning electron microscope (SEM), fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD) analysis and thermogravimetric analysis (TGA). Superior competency of the functionalized nanofibrous mat towards photocatalytic degradation of organic dye (methyl blue) in aqueous solution was observed by using UV-visible spectrophotometer with quantitative measuring method. The result indicates a complete degradation of methyl blue within 40 mins and superior reusability upto 5 cycles application. The study signifies the prospect of using electrospun nanofibers to manipulate the catalytic activity, which could be a foundation for further rational design of various composite nanofibrous materials.     

Synthesis and characterization of boron doped alumina stabilized zirconia fibers

Boron doped PVA/Zr-Al acetate nanofibers were prepared by electrospinning using PVA as a precursor. The effect of calcination temperature on morphology and crystal structure was investigated at 250, 500, and 800 °C. The study also establishes the effect of boron doping on the morphology of PVA/Zr-Al acetate nanofibers at various calcination temperatures. The measurements showed that the conductivity, pH, viscosity and the surface tension of the hybrid polymer solutions have increased with boron doping. In addition, the fibers were characterized by FTIR, DSC, XPS, XRD and SEM techniques. The addition of boron did not only increase the thermal stability of the fibers, but also increased the average fiber diameters, which gave stronger fibers. The DSC results indicated that the melting temperature (Tm) of the fibers was increased from 256 to 270 °C with the addition of boron. XRD peak patterns showed that after further heat treatment at 800 °C, zirconia exists in two phases of tetragonal and monoclinic modifications. Moreover, alumina does not transform into the γ-Al₂O₃ and θ-Al₂O₃ phase at 800 °C. The SEM appearance of the fibers showed that the addition of boron resulted in the formation of crosslinked bright surfaced fibers.     

Molecular basis of the gelatinisation and swelling characteristics of waxy barley starches grown in the same location during the same season. Part II. Crystallinity and gelatinisation characteristics

Nine waxy barley samples (grown at the same site during the same season) were investigated to identify those molecular aspects of amylopectin structure and architecture which define the order and gelatinisation characteristics. Using ¹³C CP-MAS/NMR it was confirmed that the number of double helices within the starches were approximately constant although differences in crystallinity were identified by X-ray diffraction. These differences in terms of amount of crystalline order correlated well with gelatinisation temperatures. The onset (T_o), peak (T_p) and conclusion (T_c) gelatinisation temperatures were 53.4, 59.2 and 68.1 °C on average with the associated enthalpy (ΔH) of 11.0 and 13.5 J g⁻¹ on a starch and amylopectin basis. Annealing of the starches below T_o elevated T_o, T_p and T_c by +11.9, +8.2 and +5.1 °C on average and sharpened the gelatinisation range (T_c−T_o). Acid hydrolysis after annealing increased T_o, T_p and T_c (especially T_c) by +2.3, +17.4 and +34.7 °C on average. Annealing in the presence of α-amylase elevated similarly the gelatinisation parameters by +10.2, +7.1 and +2.8 °C for T_o, T_p and T_c, respectively. Crystalline lamellae lengths were found to be 5.2±0.7 and 6.2±0.4 nm using high sensitivity differential scanning micro-calorimetry and differential scanning calorimetry, respectively.     

Development of nanofibrous membranes with far-infrared radiation and their antimicrobial properties

This study investigated the incorporation of nanoscale germanium (Ge) and silicon dioxide (SiO₂) particles into poly(vinyl alcohol) (PVA) nanofibers with the aim of developing nanostructures with far-infrared radiation effects and antimicrobial properties for biomedical applications. Composite fibers containing Ge and SiO₂ were fabricated at various concentrations of Ge and/or SiO₂ using electrospinning and layered on polypropylene nonwoven. The morphological properties of the nanocomposite fibers were characterized using a field-emission scanning electron microscope and a transmission electron microscope. The far-infrared emissivity and emissive power of the nanocomposite fibers were examined in the wavelength range of 5-20 μm at 37 °C. The antibacterial properties were quantitatively assessed by measuring the bacterial reductions of Staphylococcus aureus, Klebsiella pneumoniae, and Escherichia coli. Multi-component composite fibers electrospun from 11 wt% PVA solutions containing 0.5 wt% Ge and 1 wt% SiO₂ nanoparticles exhibited a far-infrared emissivity of 0.891 and an emissive power of 3.44·102 W m^?2 with a web area density of 5.55 g m^?2. The same system exhibited a 99.9 % bacterial reduction against both Staphylococcus aureus and Escherichia coli, and showed a 34.8 % reduction of Klebsiella pneumoniae. These results demonstrate that PVA nanofibrous membranes containing Ge and SiO₂ have potential in medical and healthcare applications such as wound healing dressings, skin care masks, and medical textile products.     

Elongation rate of sorghum leaves has a common response to meristem temperature in diverse African and European environmental conditions

We have tested whether thermal time can account for the effect of meristem temperature on leaf appearance rate (LAR) and leaf elongation rate (LER) of sorghum in a wide range of conditions without water or nutrient deficits. This requires that responses to temperature should be consistent in different locations and different seasons, and that responses of LER of different leaves of the plant should be similar. Sorghum plants (Sorghum bicolor (L.) Moench., cv. E-35-1) were sown in the field in Bamako (Mali) from October 1995 to August 1996, in Montpellier (France) in summers 1995 and 1997, and in a growth chamber. Irradiance, air and meristem temperatures (T_m) and air humidity were measured together with LER in all experiments. Unique and tight relationships were observed between T_m and LER of leaves located at different positions on the stem, for all experimental conditions when evaporative demand was low (meristem-to-air vapor pressure deficit, VPD_ma, lower than 2.5 kPa). Relationships remained linear over the whole studied range of T_m, i.e. 13–32°C (R², from 0.7 to 0.87). With high evaporative demand, LER was lower than the LER expected at the same temperature but with low VPD_ma (LER_reg); the normalized difference between LER measured on a given day (LER_a) and LER_reg was linearly related to VPD_ma (R²=0.52). A linear relationship was also observed between T_m and LAR measured before the beginning of stem elongation when T_m was lower than 27°C. The x-intercepts of relationships between T_m and LER or LAR did not differ in a covariance analysis, with a common value of 10.8°C. The use of thermal time without corrections for high temperature or photoperiod was the most appropriate way to account for the timing of leaf development. It allowed prediction of LER provided that the reduction in LER due to evaporative demand was taken into account.     

Seed germination response of cuphea to temperature

Cuphea (Cuphea viscosissima Jacq. × C. lanceolata W.T. Aiton; PSR23) is a potential new oilseed crop. Its oil is high in medium-chain fatty acids that are suitable for detergent/cleaner applications and also for cosmetics. The objective of this study was to determine the critical temperatures for cuphea seed germination. To determine the base, maximum, and optimum temperatures for seed germination, mature cuphea seeds were harvested from plants grown at Prosper, ND, in 2004, 2005, and 2006. Seeds were germinated on a temperature-gradient bar varying between 5 and 35 °C. Cumulative germination was calculated for each temperature treatment. Base temperature (T_b) and optimum temperature (T_o) were estimated from the third-order polynomial temperature-response functions for each year. In addition, germination rate per day was used in a linear model to estimate the base temperature below which germination rate was equal to zero (T_b), and the maximum temperature above which germination was equal to zero (T_m). The optimum temperature (T_o) was calculated as the intercept of sub-optimal and supra-optimal temperature-response functions. Through the third-order polynomial temperature-response functions and the sub-optimal/super-optimal intercept approaches, we were able to generate six estimates for each critical value. Estimates of the base temperature for cuphea seed germination ranged between 3.3 and 11 °C, with the most reliable estimates between 6 and 10 °C, similar to many warm-season crops such as corn (Zea mays L.) and sorghum (Sorghum bicolor L.). The optimum temperature for cuphea seed germination ranged between 18.5 and 24 °C with a mean value of 21 °C. The maximum temperature for seed germination ranged 33–38 °C. On this basis, a cuphea planting date after 20 May is recommended for east-central North Dakota.     

Investigation of the high-amylose maize starch gelatinization behaviours in glycerol-water systems

The effect of glycerol on gelatinization behaviours of high-amylose maize starch was evaluated by confocal laser scanning microscopy (CLSM), scanning electronic microscope (SEM), differential scanning calorimetry (DSC), texture analyzer (TPA) and rheometer. Gelatinization of the high-amylose maize starches with glycerol content of 10% (w/w) began at 95.4 °C (T_o), peaked at 110.3 °C (T_p), and completed at 118.9 °C (T_c). The birefringence began to disappear at around 100 °C and finished at 120 °C which corresponded well to the onset and conclusion temperatures obtained by DSC. The high-amylose maize starch granules maintained original morphological structure at 100 °C and swelled to a great degree at 110 °C. The high-amylose maize starch paste formed at 100 °C showed the lowest hardness (39.92 g), while at 120 and 130 °C, showed the highest hardness (610.89 g and 635.43 g, respectively). It should be noted that in going from 100 °C to 110 °C there is a significant increase in the viscosity of the slurry solution. The identical apparent viscosity was observed when the shear rate exceed 100 s⁻¹, resulting from the high-amylose maize starch granules were completely gelatinized at 120 °C, which was consistent with DSC analysis.     

Correlation and Regressive Model Between Spikelet Fertilized Rate and Temperature in Inter-Subspecific Hybrid Rice

To study the sensitivity of inter-subspecific hybrid rice to climatic conditions, the spikelet fertilized rate (SFR) of four types of rice including indica-japonica hybrid, intermediate hybrid, indica and japonica were analyzed during 2000-2004. The inter-subspecific hybrids showed lower SFR, and much higher fluctuation under various climatic conditions than indica and japonica rice, showing the inter-subspecific hybrids were sensitive to ecological conditions. Among 12 climatic factors, the key factor affecting rice SFR was temperature, with the most significant factor being the average temperature of the seven days around panicle flowering (T7). A regressive equation of SFR-temperature by T7, and a comprehensive synthetic model by four important temperature indices were put forward. The optimum temperature for inter-subspecific hybrids was estimated to be 26.1-26.6℃, and lower limit of safe temperature to be 22.5-23.3℃ for panicle flowering, showing higher by averagely 0.5℃ and 1.7℃, respectively, to be compared with indica and japonica rice. This suggested that inter-subspecific hybrids require proper climatic conditions. During panicle flowering, the suitable daily average temperature was 23.3-29.0℃, with the fittest one at 26.1-26.6℃. For an application example, optimum heading season for inter-subspecific hybrids in key rice growing areas in China was as same as common pure lines, while inferior limit for safe date of heading was about a ten-day period earlier than those of common pure lines.     

Thermo-Mechanical Characterization of a Thermoplastic Copolyetherester (TPC): Experimental Investigation

In this article, the thermo-mechanical characterization of poly(butylene terephthalate)/poly(tetramethylene oxide) (PBT/PTMO) is studied by thermal analysis, dynamic mechanical analysis, and uniaxial tensile tests. The results of poly(ether esters) show that the melting temperature is equal to T _m =193 °C, which is 31 °C, lower than that of the melting temperature of poly(butylene terephthalate) (PBT). Its glass transition temperature, T _g is equal to -61 °C, determined by DMA. The melting and cooling temperatures (T _m , T _c ) after aging at T₀+48 h and T₀+week are virtually unchanged. Moreover, the results of the tensile tests show that the effect of the low deformation rate reduces the friction resulting from the sliding mechanisms between the amorphous and crystalline parts.     

Preparation and Characterization of A Semi-interpenetrating Network Alkaline Anion Exchange Membrane

A series of semi-interpenetrating network (semi-IPN) anion exchange membranes (QCS/St-G_8-2-8, Quaternized chitosan/styrene-[maleic alkylene group diethyl bis (octyl dimethyl chloro/bromide), abbreviated as G_8-2-8] were prepared via in-situ polymerization by Styrene (St) and G_8-2-8 in QCS casting solution. During the process of in-situ polymerization, linear block polymers (St-G_8-2-8) of Styrene and G_8-2-8 was constructed, then was mixed with QCS casting solution, followed crosslinking the QCS by glutaraldehyde (GA). With the increasing content of linear block polymer, water uptake and swelling ratio of the composite membrane decreased; This kind of linear structure makes an order arrangement of quaternary ammonium groups which improves the OH? migration efficiency. At 70 °C, the M-30 composite membrane performs a high OH? conductivity of 8.20×10^-2 S·cm^-1, the methanol permeability is 3.23×10^-6 cm^-2·s^-1 which is still lower than Nafion 115 of 2.42×10^-6 cm^-2·s^-1, but M-30 shows a higher selectivity of 25.3 than Nafion 115 of 11.6. Furthermore, the membranes exhibited excellent thermal stability (≥150 °C), the tensile strength of the composite membrane is in the range of 14-25 MPa and elongation at break is in the range of 16-37 % at room temperature, as well as superior chemical stability in 1.0 M KOH solution for 250 h.     

Water and air temperature impacts on rice (<Emphasis Type="Italic">Oryza sativa</Emphasis>) phenology

Air temperature (T_a) is commonly used for modeling rice phenology. However, since the growing point of rice is under water during the vegetative and the early part of the reproductive period, water temperature (T_w) is likely to have a greater influence on crop developmental rates than T_a during this period. To test this hypothesis, we monitored T_w, T_a, and crop phenology in three commercial irrigated rice fields in California, USA. Sampling locations were set up on along a transect from the water inlet into the field. (Water warms up as it moves into the field.) T_a averaged 22.7 °C across sampling locations within each field, but average seasonal T_w increased from 22 °C near the inlet to 23.4 °C furthest away from the inlet. Relative to T_w furthest from the inlet, low T_w near the inlet delayed time to panicle initiation (PI 5 days) and heading (HD 8 days) and the appearance of one yellow hull on the main stem panicle (R7 9 days). Using T_w instead of T_a when the active growing point is under water until booting (midway between PI and HD) in a thermal time model improved accuracy (root-mean-square error, RMSE) for predicting time to PI by 2.5 days and HD by 1.6 days and R7 by 1.8 days. This model was further validated under more typical field conditions (i.e., not close to cold water inlets) in six locations in California. Under these conditions, average T_w was 2.6 °C higher than T_a between planting and booting, primarily due to higher daily maximum T_w values. Using T_w in the model until booting improved RMSE by 1.2 days in predicting time to HD. Using T_w instead of T_a during this period could improve the accuracy of rice phenology models.     

Effect of temperature on germination and early growth of subterranean clover, capeweed and Wimmera ryegrass

Germination of annual pasture species was studied under controlled‐environment conditions in south‐western Australia at temperatures in the range from 4°C to 35°C. Subterranean clover (Trifolium subterraneum) and Wimmera ryegrass (Lolium rigidum) had a germination of 90% between 12°C and 29°C, whereas capeweed (Arctotheca calendula) had a high germination percentage in a much narrower temperature range with an optimum of 25°C. Growth of subterranean clover, capeweed and Wimmera ryegrass between 28 and 49 days after sowing (DAS) was also studied at two photon flux densities, 13 and 30 mol m^?2 d^?1, and at diel temperatures in the range from 15/10°C to 33/28°C. Pasture species grown at a density of 1000 plants m^?2 accumulated at least twice the amount of shoot dry matter when subjected to temperatures of 21/16°C and 27/22°C, compared with a lower temperature of 15/10°C and a higher temperature of 33/28°C. Except at the highest temperature and at high photon flux density, capeweed had lower green area indices (GAI) than the other two species at 28 DAS. Crop growth rates between 28 and 49 DAS were higher in Wimmera ryegrass than in the other two species, whereas subterranean clover had a lower relative growth rate than the other two species at all temperatures and both photon flux densities. Subterranean clover and capeweed intercepted a greater proportion of the incident radiation compared with Wimmera ryegrass. The values of radiation interception and GAI were used to estimate the number of DAS to reach 75% radiation interception [f_(0·75)]. The number of days to reach f_(0·75) decreased with increasing temperature from 15/10°C to reach a minimum at 27/22°C. The time taken to achieve f_(0·75) was always shorter by about 10 d when the photon flux density was 30 mol m^?2 d^?1 in the autumn compared with 13 mol m^?2 d^?1 in the winter. These results are discussed in relation to the early growth of annual pasture in the field.     

Crop establishment methods: foliar and basal nourishment of rice (<Emphasis Type="Italic">Oryza sativa</Emphasis>) cultivation affecting growth parameters,water saving,productivity and soil physical properties

A 3-year field experiment was carried out with tillage crop establishment (TCE) and rice nourishment in north-western India to evaluate the effect of five crop establishment methods and seven fertility treatments on crop production, water productivity, profitability, and soil physical quality. Maximum panicle length (30.9 cm) was noted with F₃ treatment and minimum (22.7 cm) with F₀ treatment. Zinc application methods and timing had significantly effect on paddy yield. Maximum yield (5.22 t ha^?1) was achieved in treatment F₃ and minimum yield (2.65 t ha^?1) was noted in F₀ treatment. Results also revealed that root dry weight, root volume, and root length were recorded with higher values in F₃ treatment and minimum in F₀ treatment. TCE methods were recorded with higher values in raised beds system than T₅ at all growth stages. Treatments T₁ and T₂ reduced the mean maximum soil temperature at transplanting zone depth by 3.6 and 2.7 °C compared to the T₃. Paddy yield in T₃ was always significantly less than in T₅. On average, treatment T₄ recorded about 13 % lower water use and 3.7 % higher water productivity compared to T₅. Treatment T₅ had higher bulk density. The cumulative infiltration for 498 min was about 2 times in treatment T₁, 5 times in T₃ and more than 8 times in T₄ of the values in T₅. Mean weight diameter of aggregates was higher in T₄ followed by the T₁ and lowest in T₅. The study reveals that TCE methods T₁ and T₄ with F₃ nourishment could be more viable options for rice crop in order to save input costs and enhance profitability.     

Thermal stability and pyrolysis kinetics of organosolv lignins obtained from Eucalyptus globulus

In the present work, thermogravimetric analysis of 17 organosolv lignin samples was carried out to determine their thermal stability and calculate the kinetic parameters of their pyrolysis. The thermal stability has been estimated by the measurement of the degradation temperature (T_d), calculated according to the maximum reaction rate. In addition, degradation temperature at 10% of conversion (T_10%) has been obtained in order to compare the initial stability of the samples with T_d for all samples. The values of T_d are comprised between 262 and 389 °C and the average value is 340 °C. The range for T_10% is 251–320 °C and the average value is 270 °C. The ashes content of the samples has been analyzed and all the residues presented values lower than 4 wt%. Kinetic parameters of lignin pyrolysis were calculated by Borchardt–Daniels’ method assuming nth order reaction. The activation energy values obtained are comprised between 17.9 and 42.5 kJ/mol and the average value is 28.1 kJ/mol. These results are in agreement with the bibliography.