Estimation of failure lifetime in plywood-to-timber joints with nails and screws under cyclic loading

The performance of plywood-sheathed shear walls is determined at the plywood-to-timber joints. In joints with dowel-type fasteners, such as nails and screws, the fastener is fractured under reversed cyclic loading (e.g., seismic force), reducing the ductility of the joint. The fracture is caused by low-cycle fatigue due to the reversed cyclic bending of the fastener. Therefore, evaluating the fatigue life is important for estimating the ultimate displacement. The main objective of this study is to estimate the ultimate displacement of the joints and to enable load–displacement calculation of single shear joints under reversed cyclic displacement when bending fatigue failure of the fastener occurs. Single shear tests were conducted under different loading protocols, and the damage performances of the fasteners were determined by subjecting them to reversed cyclic bending tests. Based on the results, the failure lifetimes of joints with dowel-type fasteners were estimated. In addition, the fracture mechanism of these dowel-type fasteners was elucidated. CN50-type nails and wood screws with dimensions of 4.1?×?38 and 4.5?×?50 mm were used as fasteners. The single shear tests showed that the smaller the displacements per cycle, the lower are the ultimate displacement and ductilities of the joints. Moreover, load–displacement relationship up to fastener failure can be approximately estimated by combining the yield model and failure lifetime.     

Prediction of the load carrying capacity of bolted timber joints

Failure of bolted timber joints is analyzed experimentally and numerically. In this study, the prediction of the load-carrying capacity of dowel-type joints with one dowel under static loading is based on the analysis of fracture in wood contrarily to most engineering methods that are based on the yield theory. Mechanical joints consist of glued laminated spruce members and steel dowels. In the different analyzed tests, the bolt loads the wood parallel or perpendicular to the grain. The wood member thickness is chosen sufficiently thin to avoid the fastener from presenting plastic hinges. The influences of different structural parameters such as the dowel diameter, the edge- and end-distances are investigated. The fracture propagation analysis is carried out with the Finite Element (FE) method in the framework of Linear Elastic Fracture Mechanics (LEFM). The only identified parameter is the critical energy release rate in mode I (G_Ic). The comparison between experimental and numerical results shows that the fracture must be considered for a correct prediction of the ultimate load and that LEFM can help to improve design codes. Received 11 August 1997     

Estimation of yield and ultimate strengths of bolted timber joints by nonlinear analysis and yield theory

A finite element nonlinear analysis was conducted on bolted timber joints under lateral loads parallel and perpendicular to the grain. The results obtained from this analysis were compared with the experimental results and calculated values based on the yield theory. The analysis and experiment were performed on double shear bolted joints parallel and perpendicular to the grain with steel side plates and a slotted-in steel plate. It was found from the analysis that the yielding of wood and bolt occurred before the overall yielding of the bolted joint. Shear strength of bolted joints calculated from the yield theory using the embedding yield strength of wood and the yield moment of the bolt showed comparatively good agreement with the shear strength evaluated by 5% offset of the load–slip curve in the experiment and analysis. The shear strength of the bolted joint calculated from the yield theory using the embedding ultimate strength of wood and the ultimate moment of the bolt agreed quite well with the shear strength evaluated by the maximum load up to 15mm slip in the analysis. The former, parallel and perpendicular to the grain, were 11% and 34%, on average smaller than the latter in the experiment.Part of this paper was presented at the 52nd Annual Meeting of the Japan Wood Research Society, Gifu, April 2002; the Annual Meeting of Architectural Institute of Japan 2002, Ishikawa, August 2002; and the World Conference on Timber Engineering 2002, Shah Alam, Malaysia, August 2002     

Lateral strength of nailed timber connections with decay

Loading tests were conducted on nailed connections with decay due to a brown rot fungus. The effect of the decay on the lateral strength of nailed connections was investigated. After loading tests, the sound and decayed regions of a nailed connection were observed in the cross section, which was cut parallel to the grain through the nailed point. The nailed connections with decay showed a low load during initial deformation when the main and side members had a decayed region in the boundary between them. The nailed connections showed low load after yielding when the sound region in the main member decreased. The yield load of nailed connections with decay was calculated based on the yield theory. The model of calculations had sound and decay regions within a member. The yield load of nailed connections obtained by the calculation based on the yield theory agreed with the results obtained by experiments when significant decay in a direction parallel to the grain was observed in the main and side members. This result indicates that the yield theory can estimate the yield load of nailed connections not only with a sound member, but also a member that is partly or wholly decayed.     

Effects of pretension in bolts on hysteretic responses of moment-carrying timber joints

The adoption of a concept similar to the prestressing technique used in laminated wood decks of bridge structures might increase the initial stiffness or ultimate resistance of dowel-type timber joints by applying pretension to their bolts. This study investigated the effect of pretension in bolts on hysteretic responses and ultimate properties of moment-carrying timber joints with steel side plates. A pretension of 20 kN that yielded a prestress level of 1600 kPa or about 90% of the allowable long-term end-bearing strength of spruce species was applied to the bolts of prestressed joints. The superiority of the prestressed joint over the non-pre-stressed joint was proved by very high hysteretic damping, equivalent viscous damping ratio, and cyclic stiffness. At any given rotation level, hysteretic damping reduction and moment resistance decrement due to continuously reversed loads were found to be small because bolt pretensioning minimized the pinching effect. This study showed that the hysteresis loop of the prestressed joint can be obtained by adding the frictional hysteresis loop due to pretension force into the hysteresis loop of the non-pre-stressed joint. Despite a great increase of initial stiffness, only slight increments in ductility coefficient and ultimate moment resistance were found in the prestressed joint.     

Fracture analysis of perpendicular to grain loaded dowel-type connections using a 3D cohesive zone model

The strength and fracture behavior of dowel-type connections with stiff dowels loaded perpendicular to grain was studied by nonlinear 3D finite element (FE)-analysis. A cohesive zone model was used to model the perpendicular to grain fracture of the wood, i.e., failure by wood splitting along the grain. The influence of load eccentricity and dowel-to-loaded-edge distance was studied for a plate type of geometry loaded in tension and for a simply supported beam loaded in bending. The strength found from the FE-analysis is compared to strength from experimental tests with centric loading, showing overall good agreement. Numerical results for centric loading are further compared to strength predictions according to the linear elastic fracture mechanics (LEFM)-based design criterion present in Eurocode 5 (EN 1995-1-1:2004). The comparison showed good agreement regarding the relative influence of connection geometry, but the design criterion appears, however, to yield unconservative strength predictions. The results of the FE-analyses regarding dowel load eccentricity showed that such loading conditions may yield significantly lower strengths compared to centric loading. An approximate engineering method to account for the strength reduction due to load eccentricity is, furthermore, presented.     

Effect of combinations of wood and counterface materials on three-body abrasive wear

The abrasion characteristics of various combinations of wood and counterface materials in three-body abrasive wear were investigated. Various wood samples were examined in combination with wood, plastic, and metal counterface materials. The wear coefficient in the wood samples was calculated as the wear volume of the friction surface divided by the sliding distance and the applied load. The results showed that the wear coefficient was smaller in cases where the wood samples had greater yield stress. The wear coefficient increased as the yield stress of the various counterface materials increased, reaching a maximum value and then decreased as the yield stress increased. This result indicated that a peak value existed for the wear coefficient in combination with the counterface material.Part of this report was presented at the 51st Annual Meeting of the Japan Wood Research Society, Tokyo, April 2001     

Quasi-non-linear fracture mechanics analysis of the splitting failure of single dowel joints loaded perpendicular to grain

A quasi-non-linear fracture mechanics model based on beam on elastic foundation theory is applied for analysis of dowel joints with a single dowel loaded perpendicular to grain. The properties of the elastic foundation are chosen so that the perpendicular-to-grain tensile strength and fracture energy properties of the wood are correctly represented. It is shown that this particular choice of foundation stiffness makes a conventional maximum stress failure criterion lead to the same solution as the compliance method of fracture mechanics. Results of linear elastic fracture mechanics are obtained as a special case by assuming an infinitely large value of the foundation stiffness. Results of tests on so-called plate joints are compared with theoretical predictions, showing good agreement for variations in initial crack length as well as edge distance.     

Biodegradation of Hevea brasiliensis wood by Rigidoporus lignosus and Phellinus noxius1

In vitro wood slats degradation assays reveal that both the white root rot fungus R. lignosus and the brown root rot fungus P. noxius cause a white rot of wood. In vivo (infected tap roots) they cause the same type of decay. Nevertheless lignin determination show the rubber-tree ability to react against the parasite aggression by increased lignification of tissues.     

Determination of embedding strength of wood for dowel-type fasteners

Embedding tests parallel and perpendicular to the grain were conducted to produce a database of embedding strength of wood for the design of dowel-type joints. Dowel diameters were 8,12,16, and 20mm. Embedding strength was evaluated by the 5% off-set method and a maximum load up to 5mm displacement according to EN383. The embedding strength parallel to the grain evaluated by the former method showed values close to those obtained with the latter method, but they showed a significant difference in tests conducted perpendicular to the grain. The embedding strength parallel to the grain was 0.9 times as large as the compressive strength parallel to the grain regardless of the evaluation method. The embedding strength perpendicular to the grain evaluated by the 5% off-set method was four times as large as the compressive strength perpendicular to the grain. When the embedding strength perpendicular to the grain was evaluated by a maximum load up to 5mm displacement according to EN383, the ratio of embedding strength perpendicular to the grain to the compressive strength perpendicular to the grain decreased as the dowel diameter increased.Part of this paper was presented at the annual meeting of the Architectural Institute of Japan 1999, Hiroshima, September 1999; the 50^th annual meeting of the Japan Wood Research Society, Kyoto, April 2000; and the World Conference on Timber Engineering 2000, Whistler, Canada, July–August, 2000     

Comparative study on the durability of heat-treated White Birch (Betula papyrifera) subjected to the attack of brown and white rot fungi

Abstract

The effect of heat treatment on decay resistance of white birch was evaluated for different incubation periods ranging from 2 to 12 weeks using three species of brown rot and one species of white rot fungus. The results of weight loss tests showed that the white rot fungus, Trametes versicolor, effectively degraded the untreated wood (73.5%). While the degradation of untreated wood by brown rot fungi species, Gloephyllum trabeum (11.6%) and Conifora puteana (6.2%), was considerably less compared to T. versicolor, the third brown rot fungi studied, Poria placenta, caused an appreciable degradation of the same species (52.4%). The results clearly showed that the heat treatment reduced the effect of fungi attack on white birch. Increasing the heat treatment temperature from 195 to 215°C resulted in reduction of weight loss, consequently, reduction in fungal attack. As an example, the weight loss reductions due to T. versicolor, P. placenta, G. trabeum and C. puteana attack was 62.2%, 71.3%, 89.6% and 100%, respectively, compared to the weight loss of untreated wood when it is heat treated at 215°C. Thus, these results confirmed that the heat treatment increased the biological resistance of white birch.     

Shear resistance and failure modes of nailed joints loaded perpendicular to the grain

Shear tests were conducted on nailed joints in wood that were loaded perpendicular to the grain; these joints had 21 specifications depending on different combinations of wood species, nail dimensions, number of nails, and edge distances of the main members, and their effects on the shear resistance of the nailed joints were also investigated. The nailed joints with CN75 nails had higher initial stiffness than the joints with CN50 nails, provided the initial stiffness of nailed joints connected with 3 or 5 nails was not always a simple product of the number of nails and the initial stiffness of nailed joints connected with a nail, and instead depended on the combination of wood species of the main member and nail dimensions. When the edge distance decreased, the maximum load and energy capacity decreased, thereby affecting the energy capacity. The maximum load of the nailed joints with CN75 nails may be smaller than those with CN50 nails depending on the combination of wood species and nail dimensions. When the edge distance of the nailed joints was less than 26 mm, the energy capacity of the nailed joints with CN75 nails was less than or similar to those with CN50 nails.     

Microscopic observation of wood-based composites exposed to fungal deterioration

This study was conducted to investigate the susceptibility of various wood composite panels exposed to wood-deteriorating fungi. Five wood-attacking fungi (three mold fungi, one brown rot fungus, one white rot fungus) were inoculated into four types of commercial wood composite panels (plywood, oriented strand board, particleboard, and medium-density fiberboard). One solid wood sample was included as a control. The attacking patterns of the fungi in each panel was observed by scanning electron microscopy. The weight losses due to the exposure were compared. All wood composites were more or less susceptible to all fungi inoculated. The attacking mode of the fungi was highly dependent on the types of wood composite, which had inherently different shapes of voids owing to different shapes and characteristics of the raw furnish materials used. Plywood and medium-density fiberboard showed a large weight loss after an 8-week exposure to decay fungi. Plywood is the most susceptible to white and brown rot fungi. This study indicates that all wood composite panels should undergo careful consideration to prevent fungal deterioration when they are used for exterior and humid interior applications.     

Load-carrying capacity of steel-to-timber joints with a pretensioned bolt

Previous experimental studies reported that bolt pretensioning greatly increases the initial stiffness and load-carrying capacity of bolted joints. It is also a matter of great importance to structural designers to understand the effect of pretension on the load-carrying capacities of bolted joints, and this study presents an extended yield model that considers the fastener’s pretension force. In the extended yield model, the load-carrying capacity was defined as the load at a slip of 15 mm. The ultimate fastener bending angle at the yielded cross section equivalent to this joint slip, which was affected by the fastener’s axial force, was iteratively evaluated in numerical analyses. The introduction of bolt pretensioning largely increased the joint slip resistance at initial loading, but it decreased the ultimate fastener bending angle. This decrease of fastener bending angle resulted in a relatively low stiffness hardening (or secondary stiffness), which is caused by secondary axial forces associated with embedment of steel plates into the wood member. Prediction was verified by the tests of 36 steel-to-timber joints under three different pretension forces and two loading directions relative to the grain. Some of the observed load-carrying capacities of the joints, particularly in loading perpendicular to the grain, however, were not as high as those expected by the numerical analyses considering the given pretension forces.     

Quasi-non-linear fracture mechanics analysis of splitting failure in moment-resisting dowel joints

This article addresses the splitting failure of moment-resisting dowel-type fastener joints, in which the failure may be attributed to the perpendicular-to-grain loading of one single dowel located close to the end of a beam. A quasi-non-linear fracture mechanics model based on beam on elastic foundation theory is applied. A simple approximation suitable for practical design is also proposed. Model predictions of the influence of edge distances and end distances are compared with test results.     

Acoustoelastic effect of wood II: Effect of compressive stress on the velocity of ultrasonic longitudinal waves parallel to the transverse direction of the wood

The changes in the velocity of ultrasonic waves propagating in wood parallel to the direction of applied stress are discussed. The ultrasonic mode was longitudinal waves traveling along the direction of applied stress with the compressive load applied parallel to the transverse direction of the wood. The ultrasonic velocities were measured by the sing-around method. The experimental results indicated the existence of an acoustoelastic phenomenon in the transverse direction of the wood. The percent change in the ultrasonic velocity was given as a function of the applied stress. The change in the velocity depended on the species and structural direction of the wood. That is, in the radial direction of hardwood, the ultrasonic velocity increased with increases in compressive stress at the initial stress level of less than 2MPa; it then gradually decreased with increases in stress. A change in velocity from an increase to a decrease was considered a unique phenomenon for wood. In contrast, in the radial direction of softwood and the tangential direction of hardwood, the ultrasonic velocity decreased with increases in stress from the beginning of loading. This phenomenon is also generally observed in metallic materials. The relations between velocity and stress at the initial stress level and between velocity and strain in the range of large deformation are represented by essentially straight lines. The acoustoelastic constants of wood were obtained from these relations at the initial stress level. The absolute values of the constants in the transverse direction of wood were larger than those for metals and were larger than those for the longitudinal direction of wood reported in our previous paper.This research was presented at the 1st Meeting of the Research Society of the Acoustoelastic Measurements in the Japan Society of Non-Destructive Inspection at Osaka, October 1996 and at the 47th Annual Meeting of Japan Wood Research Society at Kochi, April 1997     

Sorption of acetylated pine wood decayed by brown rot, white rot and soft rot: different fungi—different behaviours

Acetylated wood was exposed to decay by brown, white and soft rot in order to address the sorption behaviour of decayed wood. The sorption isotherms were analysed using the Hailwood–Horrobin model. It was found that the different types of decay exhibit different sorption properties. Brown rot decayed wood exhibits significantly lower hygroscopicity in both total, monomolecular and polymolecular sorption. Soft rot decayed wood followed the same pattern as the brown rot decayed wood; however, the reduction in hygroscopicity was not significant. White rot decayed wood showed a different behaviour, with increased hygroscopicity in total and polymolecular sorption and decreased hygroscopicity in monomolecular sorption.     

Bearing properties of engineered wood products I: effects of dowel diameter and loading direction

The embedment tests of laminated veneer lumber (LVL) with two moduli of elasticity (MOE; 7.8 GPa and 9.8GPa), parallel strand lumber (PSL), and laminated strand lumber (LSL) were conducted in accordance with ASTM-D 5764. The load-embedment relation for each of these engineered wood products (EWPs) was established. The directional characteristics of bearing strength (_e), initial stiffness (k _e), and effective elastic foundation depth were obtained from the tested results. The effective elastic foundation depth (=E/k _e,E = MOE), based on the theory of a beam on elastic foundation, was obtained from thek _e and MOE. An of 90° (perpendicular to the grain) was calculated by dividingE ₉₀ [MOE of 90° from the compression test, but MOE of 0° (E ₀), parallel to the grain, obtained from the bending test] byk _e90, the initial stiffness of 90°. This study aimed to obtain the bearing characteristics of each EWP, taking into consideration their anisotropic structures, for estimating the fastening strength of a dowel-type fastener. The relations between the bearing coefficients ( _e,k _e,) on the loading direction and dowel diameter were established from the load-embedment curves. Based on the results of the embedment test, tested EWPs showed different tendencies in all directions from wood and glued laminated timber.Part of this study was presented at the 49th Annual Meeting of the Japan Wood Research Society, Tokyo, April 1999     

Micromorphological characteristics of bamboo (<Emphasis Type="Italic">Phyllostachys pubescens</Emphasis>) fibers degraded by a brown rot fungus (<Emphasis Type="Italic">Gloeophyllum trabeum</Emphasis>)

The decay pattern in bamboo fibers caused by a brown rot fungus, Gloeophyllum trabeum, was examined by microscopy. The inner part of the polylaminate secondary wall was degraded, while the outer part of the secondary wall remained essentially intact. Degradation in bamboo fiber walls without direct contact with the fungal hyphae was similar to wood decay caused by brown rot fungi. Degradation in polylaminate walls was almost confined to the broad layers whereas the narrow layers appeared resistant. The p-hydroxylphenyl unit lignin in middle lamella, particularly in the cell corner regions, was also degraded. The degradation of lignin in bamboo fibers was evidenced by Fourier transform infrared spectra. The present work suggests that the decay of bamboo fiber walls by G. trabeum was influenced by lignin distribution in the fiber walls as well as the polylaminate structures.     

Effects of density profile of MDF on stiffness and strength of nailed joints

Nail-head pull-through, lateral nail resistance, and single shear nailed joint tests were conducted on medium density fiberboard (MDF) with different density profiles, and the relations between the results of these tests and the density profiles of MDF were investigated. The maximum load of nail-head pull-through and the maximum load of nailed joints were little affected by the density profile. However, the ultimate strength of lateral nail resistance, the stiffness, and the yield strength of nailed joints were affected by the density profile of MDF and showed high values when the surface layer of the MDF had high density. It is known that bending performance is also influenced by density profile. Therefore, the stiffness and the yield strength of nailed joints were compared with the bending performance of MDF. The stiffness of nailed joints was positively correlated with the modulus of elasticity (MOE); in the case of CN65 nails, the initial stiffness of joints changed little in response to changes in MOE. The yield strength of nailed joints had a high positive correlation with the modulus of rupture (MOR). The stiffness and the yield strength of nailed joints showed linear relationships with MOE and MOR, respectively.