Surface-check variation in boxed-heart square timber of sugi (Cryptomeria japonica) cultivars dried by the conventional kiln drying

To investigate the factors affecting the surface-check variation in boxed-heart square timber of sugi (Cryptomeria japonica), surface checks formed by the conventional kiln drying were compared for two stem heights of five cultivars with different wood properties. The total length and average length of the surface checks were greater at the upper part of the stems for all the cultivars. This might be caused by more sapwood at the upper part of the stem, and large drying stresses between the outer sapwood and the inner heartwood. The cultivars, in which tangential shrinkage was large owing to small microfibril angle, formed longer surface checks and smaller bow. There was a positive relationship between surface-check length and tangential shrinkage. The heartwood percentage and tangential shrinkage were thought to be important factors affecting the surface-check variation in sugi boxed-heart square timber.     

Bow variation in kiln-dried boxed-heart square timber of sugi (<Emphasis Type="Italic">Cryptomeria japonica</Emphasis>) cultivars

To evaluate the bow variation in boxed-heart square timber of sugi (Cryptomeria japonica), bows from kiln-dried timber for five sugi cultivars with different longitudinal shrinkage trends were compared for two stem heights. Two general trends were observed, depending on the cultivar: (1) either the bow was larger at the lower than at the upper part of the stem, or (2) the bows at the lower and the upper parts of the stem were similar. In timber that had larger bow values, the gradients of longitudinal shrinkage were large across the radius and along the length of the timber. There was a positive relationship between the bow and longitudinal shrinkage. These results suggest that the bow variation between the timbers was caused by a variation in longitudinal shrinkage, which was affected by the microfibril angle. Furthermore, the bow was inversely proportional to the modulus of elasticity, which suggests that timber with a low modulus of elasticity is susceptible to a large bow due to large longitudinal shrinkage.     

Variability in physical properties of plantation-grown progenies of Melia composita and determination of a kiln-drying schedule

Plantation-grown progenies of Melia composita Willd.were studied for variability in several physical properties: density,radial and tangential shrinkage,longitudinal permeability of heartwood and sapwood.Furthermore,flat-sawn planks from each of the progeny were subjected to a quick-drying test for determination of kilndrying schedule.The mean density of the species was 0.39 g cm~(-3) and the wood may be categorized as light wood.Mean radial shrinkage(%) for the species was 2.8% with progeny-wise variation in radial shrinkage from 1.56 to 4.11%.Mean tangential shrinkage(%) for the species was 5.54% with progeny-wise variation in tangential shrinkage from 3.69 to 7.71%.The resultant tangentialradial shrinkage ratio was 1.98(less than two),which suggests that the wood is relatively stable with respect to drying behavior.Mean sapwood and heartwood longitudinal permeability of the species were 3.38 and 2.02 Darcy,respectively.Higher longitudinal permeability of sapwood and heartwood indicate better drying and preservative properties of the species.Terazawa quick-drying test method suggests that the species is less susceptible to drying defects.During the test,only moderate checks and cracks were observed.A tentative kiln-drying schedule was recommended based on these results.     

温度对人工林落叶松木材干缩及密度的影响

通过在不同的恒定的温度场中的试验,研究分析了人工林长白落叶松(Larix olgensis A.)木材干缩率、干缩比、心边材干缩差异及基本密度在不同温度条件下的变化规律,为合理地制定木材干燥工艺基准提供科学理论依据。     

3种不同处理方法对木材渗透性影响的研究

本文通过对长白鱼鳞云杉和臭冷杉生材分别进行普通气干处理和酒精置换处理以及对其气干材进行水浸处理,研究了这３种不同处理方法对木材气渗透性的影响及其影响机理。研究结果表明,长白鱼鳞云杉边材、心材和臭冷杉心村的生材经普通气干处理后,其气体渗透性较低,分别约为０．１１４、０．０４５和０．１１１ｄａｒｃｙ;长白鱼鳞云杉边材、心材和臭冷杉心材的生材经酒精置换处理后,其气体渗透性分别约为１１．７１３、０．０７４和０．１４４ｄａｒｃｙ,比普通气干处理对照组试样的平均渗透性分别增加约１０１．５倍、６２％和３０％,ｔ检验表明,前者差异非常显著,但后两者差异不显著;已气干１８个月的长白鱼鳞云杉边材、心材和臭冷杉心材经水浸处理后,其平均气体浸透性较处理前分别增加约８５％、４９％、６５．５％,ｔ检验表明差异均显著。长白鱼鳞云杉生材边材经     

Dependence of shear strength on wood properties in cultivated Larix sibirica

Abstract

Mechanical properties are very important in structural uses of wood. In the case of larch wood, shear strength (SS) may be a limiting property, because the wood is brittle and it splinters easily. In this study, SS of Siberian larch (Larix sibirica) wood was studied in relation to its axial and radial location and to some other wood properties in the part of the trunk that produces logs of good carpentry quality. SS increased by 21–23% from the pith to the outer heartwood at each studied height (butt, 4.5 and 9 m), and it was at its most approximately 7% higher at the butt than at the other studied heights. The main reason for the radial increase in SS was the increase in density caused by wood maturation, but other factors also affected SS, depending on the grouping mode (combined material, radial/axial location). An exception was sapwood, for which no factors affecting SS could be identified. Thus, sapwood may behave differently from heartwood regarding use, even unexpectedly. The results suggest that mature heartwood, but not juvenile wood and sapwood, of Larix sibirica should primarily be used in products that require high SS.     

Liquid water absorption in dried Norway spruce timber measured with CT scanning and viewed as a percolation process

Liquid flow in dried wood is complicated to study, since wood is a nonhomogeneous, hygroscopic-porous, anisotropic material. However, liquid flow is important to understand, since it has an influence on the durability of wood and on such processes like impregnation, drying, surface treatment, etc. In this study, simulations of liquid water absorption in wood as a fibre network, percolation, were compared with experimental water absorption in the longitudinal direction in spruce timber. With CT scanning, water distribution during liquid flow can be shown visually and measured by image processing. Liquid water absorption in end grain of spruce was measured with CT scanning after 1, 3, 7 and 14?days of liquid water absorption and shown as moisture content (MC) profiles in heartwood and sapwood. It was found that the amount of water absorbed could be expressed as a linear function of the square root of time. The slopes of the lines differed between sapwood and heartwood and also varied depending on the growth condition of the trees. The simulations according to the percolation method show generally good agreement with the measured results for sapwood.     

黑木相思株内木材基本材性变化与树龄关系的研究

对不同树龄和径向位置黑木相思木材的物理和主要力学性质测定研究表明:黑木相思株内边材、心材密度和主要力学性质随着树龄的增大而增大,径向和弦向的体积干缩率随着树龄的增大而减小;相同树龄黑木相思的边材密度和力学性能比心材小,干缩率比心材大.因此,在利用黑木相思时应对树龄、心边材径向位置加以特别考虑.     

不同干燥方法对杉木人工林木材浸注性的影响

采用高频真空干燥、常规窑干和高温干燥3种方法对杉木人工林木材的心、边板材进行干燥处理,用毛细管上升法评价干燥后试样的浸注性能,用半薄切片法测定干燥试样具缘纹孔的闭塞率,最后用扫描电子显微镜观察干燥试样微观构造的变化,比较分析3种干燥方法对杉木人工林木材浸注性的影响机理.结果表明:对于杉木边材,经高频真空干燥后试样的浸注性显著高于常规干燥和高温干燥后试样的浸注性,后2种干燥方法对试样浸注性影响的差异并不显著;对于杉木心材,高频真空干燥与高温干燥后试样的浸注性存在显著差异,而高频真空干燥与常规干燥之间、高温干燥与常规干燥之间对试样浸注性的影响差异均不显著;3种干燥方法处理后,杉木边材的浸注性均显著高于心材的浸注性;具缘纹孔的闭塞率较低以及部分具缘纹孔周缘破裂是高频真空干燥后木材浸注性提高的主要原因.     

杉木冷冻干燥材和气干材液体浸注性的比较研究

A comparative study was conducted on liquid penetration of the freeze-drying and air-drying sapwood and heartwood lumber of plantation Chinese fir （Cunninghamia lanceolata）. The maximum amount of dyeing solution uptake by the capillary rise method was used to evaluate the liquid penetration properties of the treated wood. The pit aspiration ratio was determined by semithin section method. Changes in wood microstructure were investigated using scanning electron microscopy. The results showed that compared with air drying, the freeze drying had a significant effect on liquid penetration of sapwood and heartwood of Chinese fir. The liquid penetration of sapwood is significantly higher than that of the heartwood for both drying treatments. Low pit aspiration ratio and cracks of pits membrane of some bordered pits are the main reasons for increasing liquid penetration after freeze drying treatment.     

Circumferential variation of heartwood and stem quality in maritime pine stems

Maritime pine (Pinus pinaster Ait.) is an important timber and pulpwood species covering about 4 million ha in Portugal, Spain and France. This work studied the cross-sectional distribution of heartwood and sapwood along the stem using 3D modelling on 20 trees. The target was to assess the potential of this species for the industrial production of heartwood sawn products. The maritime pine stems were characterized by wide sapwood of 10 cm, in average, and the presence of heartwood at all height levels with constant diameter up to 35 % tree height, decreasing afterwards. In the radial section, the heartwood follows a circumferential-like shape which changes along the stem. Pith eccentricity index values were low and homogeneous regarding to stem and higher for heartwood. Heartwood cross-sectional shape was constant up to 45 % of total height of the tree and more elongated upwards. The constant heartwood diameter, low taper and pith eccentricity index, and an approximate circular shape up to 10 m height indicated these species’ potential to produce solid wood products made out of heartwood.     

Wood drying process: impact on Scots pine lumber durability

There are indications that the drying process may have negative effects on the natural durability of wood. The impact of various drying processes on the durability of Scots pine lumber has been evaluated with mass loss in a decay test with brown rot fungus, Coniophora puteana, as measure of the decay resistance of sapwood and inner and outer heartwood. Drying with or without steam conditioning was performed in six different series: air drying, kiln drying at temperature ranges commonly used in Swedish sawmills at 70°C and 90°C with two different regulation principles, and one high-temperature drying at 110°C. Durability varied considerably both between and within boards. Sapwood showed considerable less durability than heartwood. No difference in durability was found between inner heartwood and outer heartwood. Air-dried heartwood showed the highest durability compared to other drying series. The lowest durability in sapwood and heartwood was found for series dried at the 90°C temperature level with high material temperature early in drying. The interpretation is that the duration of high material temperature at high moisture content (MC) is the critical combination for decay resistance in heartwood. Steam conditioning after drying decreased durability in sapwood.     

Internal-check variation in boxed-heart square timber of sugi (Cryptomeria japonica) cultivars dried by high-temperature kiln drying

To investigate the wood properties affecting the internal-check variation in boxed-heart square timber of sugi (Cryptomeria japonica), two cultivars, yabukuguri and kumotooshi were kiln-dried together by the high-temperature setting method and their internal checks were compared. There was a difference in the area of internal checks between the cultivars. Kumotooshi formed a larger area of internal checks, which was thought to be affected by the larger tangential shrinkage of kumotooshi. The number, total length, and total area of internal checks were significantly correlated with tangential shrinkage. The area of internal checks around the pith was also larger for kumotooshi, which might be affected by the larger tangential shrinkage in the core part of kumotooshi. The results supported that tangential shrinkage should be one of the important properties affecting the internal-check variation of sugi boxed-heart square timber.     

Impregnation of radiata pine wood by vacuum treatment II: effect of pre-steaming on wood structure and resin content

Radiata pine sapwood and heartwood were dried using high-temperature, conventional-temperature, and air drying schedules with and without pre-steaming. They were then impregnated by vacuum treatment with double-distilled water, toluidine blue, and fluorescein dye. For sapwood, there were only minor differences in uptake between drying methods and when pre-steaming was used. Using microscopy, the primary flow pathways in sapwood were found to be the resin canal network and ray parenchyma cells, which provided conduction without large resistance. In heartwood, uptake was strongly influenced by pre-steaming the green lumber. After pre-steaming heart-wood, there was an increase in uptake from all surfaces but especially from the radial surfaces. Lower extractive contents, disruption of epithelial and ray parenchyma cells, and alteration of the condition of bordered pits were also associated with pre-steaming. It was therefore possible to classify flow paths in radiata pine heartwood five ways, according to uptake values and wood anatomical features.This research was presented in part at the 48th annual meeting of the Japan Wood Research Society, Shizuoka, April 1998.     

Data analysis of hyperspectral NIR image mosaics for the quantification of linseed oil impregnation in Scots pine wood

Eight pieces of sapwood and heartwood from Scots pine, before and after linseed oil impregnation, were used to make 16 near-infrared hyperspectral images (90–200 pixels wide × 466–985 pixels long × 239 wavelengths: 982–2,480 nm). The wood pieces were selected according to a 2 × 2 experimental design using radial–tangential cut and heartwood–sapwood as factors with two replicates. A first mosaic of 16 images was cleaned and analyzed by image principal component analysis. Interpretation was realized by studying score images and score plots by brushing interaction. In the resulting T1–T2 score plot, the untreated pieces formed a dense cluster, while the impregnated ones showed larger variation. The good separation of treated and impregnated clusters was confirmed by PLSDA showing low false negatives and positives. Analysis of the eight impregnated wood pieces clearly showed regions of wrong impregnation in one wood piece. Loadings resembling linseed oil spectra indicated that this was due to badly polymerized linseed oil. After removing the outlier piece, a new model was made on the seven-piece mosaic showing in the T1–T2 score plot that heartwood and sapwood absorbed the linseed oil differently. This difference was not detected in the untreated wood, so it had to come from the impregnation process. Edges reacted differently from surfaces to the impregnation process as seen in the T1–T4 score plot. These findings show that a future online quality inspection of both raw wood and impregnated pieces would be feasible.     

Variability of wood properties in two wild cherry clonal trials

There has been an increase in wild cherry cultivation over recent decades, revealing a need for improvements in planting material to be used for the production of high quality timber. To date, trial tests have been carried out mainly on growth and tree architectural traits, while no investigations have focused on wood properties. The present study investigated the variability of the growth traits and the physical and mechanical properties of wild cherry wood, both within the tree, within and among clones and between sites. The aims of the study are to provide useful information on the genetics of wood traits in valuable hardwoods and to discuss how within-tree variation can affect early selection of genotypes. The results suggest that site was the most important source of variation in growth traits and in the proportion of heartwood, although differences among clones were highly significant. The number of sapwood rings was very homogeneous both between sites and among clones. Concerning the wood traits, most variation was detected within the tree, rather than within or among clones or between sites. Within tree variability seems to be mainly due to heartwood/sapwood presence. However, since there is a high correlation between heartwood and sapwood properties, a quite efficient selection made on the basis of sapwood should provide an efficient means of selecting heartwood traits.     

Moisture content gradient in a softwood board during drying: simulation from a 2-D model and measurement

Summary A 2-D mathematical model was developed to simulate moisture movement and heat transfer in width and thickness directions within a softwood board during drying. The model is based on wood physiological features and behaviour observed during drying. In sapwood, liquid water movement is assumed to be a consequence of capillary action between liquid and gas phases inside the cell lumens. However, liquid flow does not occur in wood close to the exposed surfaces because at timber surfaces the wood cells are damaged during the sawing process and consequently the liquid column is broken. In heartwood, liquid flow is negligible since the pits are normally aspirated during the formation of heartwood in the growing tree. Water vapour moves under a partial vapour pressure gradient while bound water diffuses within the wood material due to differences in chemical potential. The model was solved numerically to predict moisture-content profiles. Experiments were undertaken to measure the moisturecontent gradient. Samples were removed from a tunnel dryer at intervals throughout drying, frozen overnight and then cut into slices for moisture-content determination. The experimental results were used to verify the model.This work is supported by the New Zealand Foundation of Research, Science and Technology under contract CO4415     

13种杨树木材物理力学性质的研究

采集1－69杨等10种黑杨的9年生试材，易县毛白杨等3种白杨的13年生试材，测试木材物理力学性能，分析心边材，不同树高位置，株间的变化规律，比较品种间木材性质的差异，试验结果表明，13种杨树全树木材心材率在14．6－34．1％，之间，生材含水率在86．2－148．5％之间，由生材干燥至含水率为12％所产生的干缩率在8．66％－11．96％这间，气干密度属低类或很低类，强度属弱类，硬度属软类或甚软类，冲击韧性中等；黑杨心材颜色深，心边材性质差异大，白杨心材颜色淡，心边材性质差异小，品种间木材物理力学性质差异较大，按其主要特点可将13个品种的木材分为4类。     

Effect of different drying methods on liquid penetration of Chinese fir plantation wood

Chinese fir plantation sapwood and heartwood boards were treated by three drying methods: radio frequency-vacuum drying (RFVD), conventional kiln drying (KD) and high temperature drying (HTD). The maximum amount of dyeing solution uptake by the capillary rising method was used to evaluate the liquid penetration of the treated wood. The pit aspiration ratio was determined by a semithin section method. Changes in wood microstructure were investigated using scanning electron microscopy. The results show that liquid penetration of Chinese fir sapwood after RFVD is significantly higher than that after KD and HTD. Liquid penetration of Chinese fir heartwood after RFVD is higher than that after HTD. Liquid penetration of Chinese fir sapwood is significantly higher than that of heartwood after three drying treatments. Low pit aspiration ratio and cracks of some bordered pits are the main reasons for the increase in liquid penetration after RFVD treatment. __________ Translated from Scientia Silvae Sinicae, 2006, 42(10): 85–90 [译自: 林业科学]     

Modelling of the behaviour of free water in sapwood during drying

A stochastic three-dimensional model for the behaviour of free water in wood, which was described in Part I, is used for the simulation and analysis of some further features of wood drying. The kiln brown stain mechanism is studied and the connection to the condition of the wood surface is pointed out. Several drying rate questions and related aspects are analysed and compared with experimental results. Finally the risk of surface checking in an early stage of sapwood drying is shown theoretically.