Discovery of sodium in the atmosphere of mercury

The spectrum of Mercury at the Fraunhofer sodium D lines shows strong emission features that are attributed to resonant scattering of sunlight from sodium vapor in the atmosphere of the planet. The total column abundance of sodium was estimated to be 8.1 x 10(11) atoms per square centimeter, which corresponds to a surface density at the subsolar point of about 1.5 x 10(5) atoms per cubic centimeter. The most abundant atmospheric species found by the Mariner 10 mission to Mercury was helium, with a surface density of 4.5 x 10(3) atoms per cubic centimeter. It now appears that sodium vapor is a major constituent of Mercury's atmosphere.     

Vertical structure of the ionosphere and upper neutral atmosphere of saturn from the pioneer radio occultation

Radio occultation measurements at S band (2.293 gigahertz) of the ionosphere and upper neutral atmosphere of Saturn were obtained during the flyby of the Pioneer 11 Saturn spacecraft on 5 September 1979. Preliminary analysis of the occultation exit data taken at a latitude of 9.5 degrees S and a solar zenith angle of 90.6 degrees revealed the presence of a rather thin ionosphere, having a main peak electron density of about 9.4 x 10/(3) per cubic centimeter at an altitude of about 2800 above the level of a neutral number density of 10(19) per cubic centimeter and a lower peak of about 7 x 10(3) per cubic centimeter at 2200 kilometers. Data in the neutral atmosphere were obtained to a pressure level of about 120 millibars. The temperature structure derived from these data is consistent with the results of the Pioneer 11 Saturn infrared radiometer experiment (for a helium fraction of 15 percent) and with models derived from Earth-based observations for a helium fraction by number of about 4 to 10 percent. The helium fraction will be further defined by mutual iteration with the infrared radiometer team.     

MgB2 superconducting thin films with a transition temperature of 39 kelvin

We fabricated high-quality c axis-oriented epitaxial MgB2 thin films using a pulsed laser deposition technique. The thin films grown on (1 i 0 2) Al2O3 substrates have a transition temperature of 39 kelvin. The critical current density in zero field is approximately 6 x 10(6) amperes per cubic centimeter at 5 kelvin and approximately 3 x 10(5) amperes per cubic centimeter at 35 kelvin, which suggests that this compound has potential for electronic device applications, such as microwave devices and superconducting quantum interference devices. For the films deposited on Al2O3, x-ray diffraction patterns indicate a highly c axis-oriented crystal structure perpendicular to the substrate surface.     

Venus: density of upper atmosphere from measurements of drag on pioneer orbiter

Measurements of the changes in orbital period of the Pioneer Venus orbiter have yielded estimates of the density of the upper atmosphere of Venus at altitudes in the range from 150 to 200 kilometers. At the lower limit of this range, the density on the dayside of the terminator exhibits a temporal variation of amplitude near 4 x 10(-14) gram per cubic centimeter aboult a mean of approximately 1.4 x 10(-13) gram per cubic centimeter. The variation appears oscillatory, with a 4- to 5-day period, but barely one cycle was observed. The density on the nightside of the terminator, sampled inthe same 150-kilometer altitude range, fluctuates about a smaller mean of approximately 4 x 10(-14) gram per cubic centimeter. The density between the altitudes of 150 and 200 kilometers, sampled only on the dayside of the terminator, imply a scale height of between 15 and 20 kilometers. The interpretation of this estimate is uncertain, however, in view of the measurements at the different altitudes having been made at different times and, hence, at different values of solar phase.     

Preliminary results on the atmospheres of io and jupiter from the pioneer 10 s-band occultation experiment

The preliminary analysis of data from the Pioneer 10 S-band radio occultation experinment has revealed the presence of an ionosphere on the Jovian satellite Io (JI) having an electron density peak of about 6 x 10(4) electrons per cubic centimeter at an altitude of approximately 60 to 140 kilometers. This suggests the presence of an atmosphere having a surface number density of about 10(10) to 10(12) per cubic centimeter, corresponding to an atmospheric surface pressure of between 10(-8) and 10(-10) bar, at or below the detection threshold of the Beta Scorpii stellar occultation. A measurement of the atmosphere of Jupiter was obtained down to the level of about 80 millibars, indicating a large temperature increase at about the 20 millibar level, which cannot be explained by the absorption of solar radiation by methane alone and can possibly be due to absorption by particulate matter.     

Jovian Atmosphere: Structure and Composition between the Turbopause and the Mesopause

The occultation of the star Beta Scorpii by Jupiter was observed at high time resolution in three wavelength channels. The results imply a temperature of 220 degrees K at an altitude in the Jovian atmosphere corresponding to 10(14) molecules per cubic centimeter, and temperature fluctuations of 2 degrees to 10 degrees K over vertical scales of 2 to 10 kilometers. They suggest that the vertical eddy diffusion coefficient near the turbopause has a lower limit of 7 x 10(5)K square centimeters per second, and that the turbopause lies above the altitude where the density is 5 x 10(13) molecules per cubic centimeter. Below the turbopause, the ratio of hydrogen to helium is consistent with cosmic abundances.     

Measurement of Laser-Plasma Electron Density with a Soft X-ray Laser Deflectometer

A soft x-ray laser (wavelength lambda = 15.5 nanometers) was used to create a moiré deflectogram of a high-density, laser-produced plasma. The use of deflectometry at this short wavelength permits measurement of the density spatial profile in a long-scalelength (3 millimeters), high-density plasma. A peak density of 3.2 x 10(21) per cubic centimeter was recorded.     

Rapid formation of sulfuric acid particles at near-atmospheric conditions

We investigated the formation of new particles in a laboratory study, starting from H2SO4 produced in situ through the reaction of OH radicals with SO2. Newly formed particles were observed for H2SO4 concentrations above 7 x 10(6) per cubic centimeter. At 293 kelvin, a rough estimate yielded a nucleation rate of 0.3 to 0.4 particles per cubic centimeter per second for approximately 10(7) particles per cubic centimeter of H2SO4 (particle size >/= 3 nanometers). These findings are in agreement with observations from the atmosphere. The results demonstrate that under laboratory conditions similar to the atmosphere, particle formation occurs at atmospheric H2SO4 concentration levels.     

Plasma diagnosis from thermal noise and limits on dust flux or mass in comet giacobini-zinner

Thermal noise spectroscopy was used to measure the density and temperature of the main (cold) electron plasma population during 2 hours (1.5x10(5) kilometers perpendicular to the tail axis) around the point of closest approach of the International Cometary Explorer (ICE) to Comet Giacobini-Zinner. The time resolution was 18 seconds (370 kilometers) in the plasma tail and 54 seconds (1100 kilometers) elsewhere. Near the tail axis, the maximum plasma density was 670 per cubic centimeter and the temperature slightly above 1 electron volt. Away from the axis, the plasma density dropped to 100 per cubic centimeter (temperature, 2x 10(4) K) over 2000 kilometers, then decreased to 10 (1.5x 10(5)K) over 15,000 kilometers; outside that region (plasma tail), the density fluctuated between 10 and 30 per cubic centimeter and the temperature between 1x 10(5) and 4 x10(5) K. The relative density of the hot population rarely exceeded a few percent. The tail was highly asymmetrical and showed much structure. On the other antenna, shot noise was recorded from the plasma particle impacts on the spacecraft body. No evidence was found of grain impacts on the antennas or spacecraft in the plasma tail. This yields an upper limit for the dust flux or particle mass, indicating either fluxes or masses in the tail smaller than implied by the models or an anomalous grain structure. This seems to support earlier suggestions that these grains are featherlike. Outside the tail, and particularly near 10(5) kilometers from its axis, impulsive noises indicating plasma turbulence were observed.     

Density-modulus relationship in graphite fibers made from acrylic yarns

Three types of polyacrylonitrile yarn were converted to graphite fibers. There was a linear relation between density and Young's modulus of the graphite fibers, the ranges observed being 1.58 to 2.18 grams per cubic centimeter and 25 to 112 x 10(6) pounds per square inch.     

Jupiter's Ionosphere: Prospects for Pioneer 10

Model Jovian ionospheres are constructed for comparison with Pioneer 10 results. Electron density maxima are predicted at a level approximately 220 kilometers above an assumed reference height where the hydrogen density is 10(16) molecules per cubic centimeter. It may be possible to use observations of the electron density to locate the turbopause. Attention is drawn to a possible strong source of ionized sodium from lo which might lead to large electron densities at low altitudes.     

Venus: mass, gravity field, atmosphere, and ionosphere as measured by the mariner 10 dual-frequency radio system

Analysis of the Doppler tracking data near encounter yields a value for the ratio of the mass of the sun to that of Venus of 408,523.9 +/- 1.2, which is in good agreement with prior determinations based on data from Mariner 2 and Mariner 5. Preliminary analysis indicates that the magnitudes of the fractional differences in the principal moments of inertia of Venus are no larger than 10(-4), given that the effects of gravity-field harmonics higher than the second are negligible. Additional analysis is needed to determine the influence of the higher order harmonics on this bound. Four distinct temperature inversions exist at altitudes of 56, 58, 61, and 63 kilometers. The X-band signal was much more rapidly attenuated than the S-band signal and disappeared completely at 52-kilometer altitude. The nightside ionosphere consists of two layers having a peak density of 10(4) electrons per cubic centimeter at altitudes of 140 and 120 kilometers. The dayside ionosphere has a peak density of 3 X 10(5) electrons per cubic centimeter at an altitude of 145 kilometers. The electron number density observed at higher altitudes was ten times less than that observed by Mariner 5, and no strong evidence for a well-defined plasmapause was found.     

Epitaxial cubic gadolinium oxide as a dielectric for gallium arsenide passivation

Epitaxial growth of single-crystal gadolinium oxide dielectric thin films on gallium arsenide is reported. The gadolinium oxide film has a cubic structure isomorphic to manganese oxide and is (110)-oriented in single domain on the (100) gallium arsenide surface. The gadolinium oxide film has a dielectric constant of approximately 10, with low leakage current densities of about 10(-9) to 10(-10) amperes per square centimeter at zero bias. Typical breakdown field is 4 megavolts per centimeter for an oxide film 185 angstroms thick and 10 megavolts per centimeter for an oxide 45 angstroms thick. Both accumulation and inversion layers were observed in the gadolinium oxide-gallium arsenide metal oxide semiconductor diodes, using capacitance-voltage measurements. The ability to grow thin single-crystal oxide films on gallium arsenide with a low interfacial density of states has great potential impact on the electronic industry of compound semiconductors.     

Oceanic electric fields: perception by american eels?

American eels, long-distance migrating fish, consistently exhibited conditioned cardiac deceleration responses to electric fields as small as 0.167 x 10(-2) microampere per square centimeter in water of resistivity 4000 ohm centimeters (6.7 microvolts per centimeter) and 400 ohm centimeters (0.67 microvolt per centimeter). Fewer responses were shown at this current density (0.167 x 10(-2) microampere per square centimeter) in more saline water (40 ohm centimeters, 0.067 microvolt per centimeter) and at a lower current density (0.167 x 10(-3) microampere per square centimeter) in fresh water. Thus, eels have sufficient sensitivity to utilize geoelectric information for orientation.     

Ultralight metallic microlattices

Ultralight (<10 milligrams per cubic centimeter) cellular materials are desirable for thermal insulation; battery electrodes; catalyst supports; and acoustic, vibration, or shock energy damping. We present ultralight materials based on periodic hollow-tube microlattices. These materials are fabricated by starting with a template formed by self-propagating photopolymer waveguide prototyping, coating the template by electroless nickel plating, and subsequently etching away the template. The resulting metallic microlattices exhibit densities ρ ≥ 0.9 milligram per cubic centimeter, complete recovery after compression exceeding 50% strain, and energy absorption similar to elastomers. Young's modulus E scales with density as E ~ ρ(2), in contrast to the E ~ ρ(3) scaling observed for ultralight aerogels and carbon nanotube foams with stochastic architecture. We attribute these properties to structural hierarchy at the nanometer, micrometer, and millimeter scales.     

Normal atmosphere: large radical and formaldehyde concentrations predicted

A steady-state model of the normal (unpolluted) surface atmosphere predicts a daytime concentration of hydroxyl, hydroperoxyl, and methylperoxyl radicals approaching 5 x 10(8)molecules per cubic centimeter and a formaldehyde concentration of 5 x 10(10) molecules per cubic centimeter or 2 parts per billion. A radical chain reaction is proposed for the rapid removal of carbon monoxide, leading to a carbon monoxide lifetime as low as 0.2 year in the surface atmosphere.     

Gravitational parameters of the jupiter system from the Doppler tracking of pioneer 10

Preliminary analyses of Doppler data from Pioneer 10 during its encounter with Jupiter indicate that the mass of Io is about 20 percent greater than previously thought and that Io's mean density is about 3.5 grams per cubic centimeter. A determination of the dynamical flattening of Jupiter (a - b)/a (where a is the semimajor axis and b is the semiminor axis) is found to lie in the neighborhood of 0.065, which agrees with the value determined from satellite perturbations.     

Mercury: results on mass, radius, ionosphere, and atmosphere from mariner 10 dual-frequency radio signals

Analysis of the radio-tracking data from Mariner 10 yields 6,023,600 +/- 600 for the ratio of the mass of the sun to that of Mercury, in very good agreement with values determined earlier from radar data alone. Occultation measurements yielded values for the radius of Mercury of 2440 +/- 2 and 2438 +/- 2 kilometers at laditudes of 2 degrees N and 68 degrees N, respectively, again in close agreement with the average equatorial radius of 2439 +/- 1 kilometers determined from radar data. The mean density of 5.44 grams per cubic centimeter deduced for Mercury from Mariner 10 data thus virtually coincides with the prior determination. No evidence of either an ionosphere or an atmosphere was found, with the data yielding upper bounds on the electron density of about 1500 and 4000 electrons per cubic centimeter on the dayside and nightside, respectively, and an inferred upper bound on the surface pressure of 10(-8) millibar.     

Parameters of the plasma affecting the radiation of pulsar 1

Analysis of the relation between time delay and frequency for pulses from Pulsar 1 shows that the dispersive region of the ray path must exceed 300 astronomical units and have an average electron number density less than 8000 per cubic centimeter and average magnetic field strength less than 2 x 10(-3) gauss. These requirements almost guarantee that the observed dispersion takes place in the interstellar medium.     

A spectroscopic measurement of the coronal density of procyon

One of the open key issues in the astrophysics of stellar coronae is the determination of their spatial structure and density. From almost all previous measurements, one can infer merely the presence of a corona, which for the most energetic stellar coronae may exceed the solar x-ray output by as much as five orders of magnitude, but no information can be obtained on the densities and hence volumes and sizes of the hot x-ray emitting material. A direct spectroscopic measurement of the coronal density was obtained for the star Procyon with the spectrometer on board the Extreme Ultraviolet Explorer satellite; the ratio of two Fe XIV lines at 211.32 and 264.79 angstroms was used to determine a density of approximately 4 x 10(9) to 7 x 10(9) electrons per cubic centimeter, which is a factor of 2 to 3 higher than typical solar active region densities. From this value, we estimate that approximately 6 percent of the stellar surface is covered with approximately 7 x 10(4) coronal loops.