Fabric objective measurement of the plasma-treated cotton fabric subjected to wrinkle-resistant finishing with BTCA and TiO<Subscript>2</Subscript> system

Handle is an important factor when designing the end-uses of fabric as it is also a critical factor for purchasing decision. In the present study, the Kawabata Evaluation System for Fabrics (KES-F) was used for measuring the fabric handle of BTCA-TiO₂ treated cotton fabric with or without plasma pre-treatment. The results revealed that the BTCA-TiO₂ treated cotton fabrics without plasma pre-treatment had a negative effect on tensile, shearing, compressional, and surface properties while the bending properties were improved. On the other hand, the plasma pre-treatment improved the tensile and compressional properties, but not the bending, shearing, and surface properties.     

Relationship between curing temperature and low stress mechanical properties of titanium dioxide catalyzed flame retardant finished cotton fabric

N-methylol dimethylphosphonopropionamide is a flame-retardant agent commonly combined with melamine resin and phosphoric acid catalyst to impart flame-retardant property to cotton fabrics. A co-catalyst titanium dioxide (TiO₂) is added into the formulation in order to improve the flame-retardant performance by enhancing the crosslinking reaction and physically attaching on to cotton fabrics. The fabrics cured at temperature of 150 °C and 170 °C have a better flame-retardant ability and can withstand multiple times of home laundering compared with those cured at temperature of 110 °C and 130 °C. The flame-retardant ability is further enhanced by treating the fabrics in the presence of TiO₂. In addition, the low stress mechanical properties measured by Kawabata Evaluation System for Fabric (KES-F) are altered after flame-retardant treatment. These changes are contributed by the formation of crosslinks after treatment, acid-catalyzed depolymerization in a strong acidic medium and the presence of co-catalyst TiO₂. In addition, the properties of cotton fabrics depend greatly on the choice of curing temperature. High curing temperature usually caused poor hand properties of the fabrics due to the extensive crosslinks formation. Lastly, the existence of TiO₂ in the treatment not only improves the reaction efficiency but also has positive enhancement with respect to compressional recovery ability and tensile properties.     

Antibacterial finishing of cotton fabric via the chitosan/TPP self-assembled nano layers

In this study, chitosan and pentasodium tripolyphosphate (TPP)-based bilayers were fabricated on the cationized woven cotton fabrics via layer-by-layer (LBL) self-assembly technique. The initial cationic charges on cotton fabric were produced through the aminization procedure involving the covalent attachment of reactive dye to cotton fabric and subsequent reductive cleavage of the dye to free amine. Different numbers of bilayers (1, 5, and 10) consisting of chitosan/TPP have been deposited on the fabrics. The surface morphology, cationic group content, chemical surface modification, whiteness index, surface tension and antibacterial properties of the modified cotton samples were investigated using scanning electron microscopy (SEM), methylene blue test, FTIR, reflectance spectroscopy, water contact angle measurements and antibacterial test, respectively. The bacterial inhibition experiments demonstrated that the modified cotton fabric with the addition of chitosan/TPP bilayers can increase the degree of inhibition on E. coli and S. aureus bacteria. The utilized LBL method was an easy and cost-effective procedure for developing of novel antibacterial textiles with the highly attractive feature in the medical and hygienic products.     

Investigation on the effect of titanium dioxide nano particles on camouflage properties of cotton fabrics

Cotton fabrics were dyed with three commercial vat dyes in order to provide camouflage in Vis-NIR regions and imitate reflectance profile of greenish leaves. To investigate the effect of nano particles on camouflage properties of dyed fabric, nano particles of TiO₂ were applied on dyed fabrics using pad-dry-cure method. The nano TiO₂ padded dyed fabrics were investigated using scanning electron microscopy (SEM). Reflectance curves of coated dyed samples with different concentrations of nano TiO₂ were measured. Results showed that in both of the standard shades, nano TiO₂ increases the reflectance value in NIR region and with increasing the concentration of nano TiO₂, the reflectance curves of samples tend to show the maximum reflection of greenish leaves (deciduous leaves) in NIR region. Chromatic values (CIE1976 L*, a*, and b*) and color difference (according to CIECMC color difference ΔE*cmc (2:1)) of each of the coated samples were measured using the reflection spectrophotometer. By considering the influence of white color of nano TiO₂ on green shade of dyed cotton fabrics and increasing the color difference (between coated samples and the standard shades of the 1948 U.S army pattern) in visible range, optimum concentrations of nano TiO₂ for development of camouflage properties on cotton fabrics in both NIR and visible region were determined. These values for NATO and forest green shades were 0.75 % and 0.5 %, respectively. Fastness results showed that both of the samples have acceptable color fastness. The effect of washing and exposure to light on camouflage properties of coated dyed fabrics in visible (in term of chromatic values) and NIR region (in term of spectral reflectance) was investigated when those were coated in optimum concentrations of nano TiO₂. The results showed that the effect of after treatments (washing and exposure to light) on surface color spectral characteristics and camouflage properties was inconsiderable.     

Durable press finish of cotton fabric using malic acid as a crosslinker

It has been considered that malic acid,α-hydroxy succinic acid, could not form crosslinks in the cellulosic materials unless activated by other polycarboxylic acids such as butanetetracarboxylic acid or citric acid because there are only two carboxylic acids per molecule available for the formation of one anhydride intermediate. However we found that the dicarboxylic malic acid with sodium hypophosphite catalyst without the addition of other crosslinkers was able to improve wrinkle resistance of cotton up to 294° (dry WRA) and 285° (wet WRA), which is a measure of crosslinking level in cotton.¹H FT-NMR, FT-IR and GPC analysis indicated the in-situ formation of an trimericα, β-malic acid with a composition of 1:3 through the esterification between hydroxyl group and one of carboxylic groups in malic acid during curing. The crosslinking of cotton was attributed to the trimericα, β-malic acid, a tetracarboxylic acid, which can form two anhydride rings during curing. The influence of crosslinking conditions such as concentrations of malic acid and catalyst, pH of the formulation bath, and curing temperature were investigated in terms of imparted wrinkle resistance and whiteness. The addition of reactive polyurethane resin in the formulation slightly increased the mechanical strength retention of crosslinked fabric coupled with additional increase in wrinkle resistance.     

Effect of nano SrTiO3 supporting nano TiO2 on self-cleaning of cotton fabric

This study reports the results of an investigation aiming at finding what affect nano titania (TiO₂) and nano strontium titanate (SrTiO₃) on self-cleaning of cotton fabrics. The photocatalytic activity of nano strontium titanate has been examined on cotton fabric under UV irradiation in various concentrations in mixing of nano titania. The amount of loaded nano titania and nano strontium titanate particles on cotton fabrics were investigated using X-ray fluorescence spectrometry (XRF) and crystallinity of coatings by X-ray diffraction spectroscopy (XRD). The treated cotton fabrics, which were stained with two common synthesized dyes, were exposed to 400 W UV radiation for 30 hours and their self-cleaning property was investigated by a reflectance spectrophotometer. Scanning electron microscope (SEM) images show pervasion of nano materials on the surface of the treated cotton. Adding nano strontium titanate to nano titania showed the most promising photocatalytic activity toward dye degradation.     

Application of silver nanoparticles to cotton fabric as an antibacterial textile finish

A novel nano-silver colloidal solution was prepared in one step by mixing AgNO₃ aqueous solution and an amino-terminated hyperbranched polymer (HBP-NH₂) aqueous solution under vigorous stirring at room temperature. All results of Dynamic Light Scattering (DLS), Transmission Electron Microscopy (TEM) and UV/Visible Absorption Spectrophotometry indicated that silver nanoparticles had been formed in colloidal solution. Cotton fabric was treated with nano-silver colloid by an impregnation method to provide the cotton fabric with antibacterial properties. The whiteness, silver content, antibacterial activity and washing durability of the silver-treated fabrics were determined. The results indicated that the silver-treated cotton fabric showed 99.01 % bacterial reduction of Staphylococcus aureus and 99.26 % bacterial reduction of Escherichia coli while the silver content on cotton was about 88 mg/kg. The antimicrobial activity of the silver-treated cotton fabric was maintained at over 98.77 % reduction level even after being exposed to 20 consecutive home laundering conditions. In addition, the results of scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS) confirmed that silver nanoparticles have been fixed and well dispersed on cotton fabrics’ surface and the major state of the silver presented on the surface was Ag⁰.     

Effect of Urea/NaOH aqueous system on morphology and properties of cotton fabric

This paper was focused on comparing the effect of urea/NaOH aqueous system with that of single urea or NaOH treating system on cotton fabric morphology and properties. Optical microscopy (OM), scanning electron micrograph (SEM), Fourier transform infrared spectroscopy (FT-IR), and wide X-ray diffraction (WAXD) were used to study cotton fabric morphology and properties before and after treatment by urea/NaOH, single urea, and single NaOH treating systems. Results showed that the cotton fabric treated by urea/NaOH aqueous system had better dyeability than the samples untreated and treated by single urea or single NaOH treating systems. Obvious differences were observed in appearance and morphology of cotton fabrics before and after treatment by urea/NaOH aqueous system. The composition and the structure of urea/NaOH treated cotton fiber had no distinct changes, only except the reduced hydrogen bonding between cellulosic macromolecules. Tensile strength and elongation at break of cotton fabric showed a slight decrease after treatment by urea/NaOH system. In addition, shrinkage of area and weight reduction of urea/NaOH treated samples were higher than those of the samples untreated and treated by single urea or single NaOH treating system.     

Synthesis of HBP-HTC and its application to cotton fabric as an antimicrobial auxiliary

A quaternary ammonium compound, 2-hydroxypropyltrimethylammonium chloride amino-terminated hyper-branched polymer (HBP-HTC), was synthesized from an amino-terminated hyperbranched polymer (HBP-NH₂) and 2,3-epoxypropyltrimethylammonium chloride (EPTAC) as a grafting agent in aqueous solution. Its molecular weight and possible structure were characterized by gel permeation chromatography (GPC), Fourier transform infrared spectroscopy (FTIR) and nuclear magnetic resonance spectroscopy (¹H-NMR). The cotton fabric was treated with 2 g/l HBP-HTC aqueous solution for 30 min at room temperature to provide the cotton fabric with antimicrobial properties. The antimicrobial activities of the HBP-HTC aqueous solutions and the HBP-HTC treated cotton fabrics were evaluated quantitatively. The results indicated that the HBP-HTC treated cotton fabric showed 99.92 % reduction of bacteria S. aureus and 99.66 % reduction of bacteria E. coli, respectively. The antimicrobial activities of the HBP-HTC treated cotton fabrics were maintained at over 99.00 % reduction level even after being exposed to 20 consecutive home laundering conditions.     

Effect of various shapes of zinc oxide nanoparticles on cotton fabric for UV-blocking and anti-bacterial properties

Various shapes of ZnO — multi-petals, rod and spherical — were prepared and then applied on cotton fabric for UV-blocking and anti-bacterial properties. The ZnO particles were investigated by XRD and SEM. The as-prepared suspension was applied onto cotton fabrics via the pad-dry-cure process at 150 °C. The characteristics of the fabric coating were investigated by SEM, XRD and Atomic Absorption Spectroscopy (AAS). The UV-blocking effectiveness was measured with a UV-Vis spectrophotometer whilst the antibacterial activity was determined using the AATCC 147 method. The results of XRD and SEM on the ZnO powders show that we can produce various shapes of ZnO. The investigation by SEM and AAS clearly revealed that ZnO was effectively deposited on the cotton surface and that the adhesion was retained after washing ten cycles. The sphericals-shaped ZnO and multi-petals shaped ZnO coated fabrics show excellent UV-blocking properties. All treated samples showed good antibacterial activity against Staphylococcus Aureus. The shape of ZnO shows no considerable effect on antibacterial properties.     

Development of zero formaldehyde easy care finishing system by using nano titanium dioxide with citric acid and its impact on physical properties

The Performance of nano TiO₂ with citric acid cross-linker was assessed by using pad-dry-cure method on cotton fabric. Significant increase in crease recovery performance was observed which was previously only associated with the lengthy ultraviolet irradiation process. The optimum amount of only 0.1 % nano TiO₂ was needed with the citric acid to exhibit significant increase in easy care performance of the fabric. Typically, application of a cross-linker to cellulosics will impart a deleterious effect on the softness of the fabric; however, incorporation of nano-TiO₂ with the citric acid cross-linker significantly improved the softness of the fabric which was reflected in the mean deviation of coefficient of friction (MMD) and interyarn friction (2HG5) KES-F values. In addition, there was improvement in tensile strength retention of the fabric as well.     

Influence of low temperature plasma treatment on the properties of ink-jet printed cotton fabric

The aim of this paper is to study the possibility and effectiveness of applying LTP treatment to enhance the performance of pre-treatment paste containing sodium alginate so as to improve the properties of the ink-jet printed cotton fabric. Experimental results revealed that the LTP pre-treatment in couple with the ink-jet printing technique could improve the final printed properties of cotton fabric.     

An investigation of continuous finishing and dyeing on the mechanical properties and handle of cotton fabrics

In this paper, the effect of continuous finishing-desizing, scouring, bleaching and dyeing of woven cotton fabrics on the low stress mechanical and surface properties has been studied. The cotton fabric properties were measured by the famous KES-FB system. The handle of the finished fabrics were calculated by the handle evaluation programme. The results showed that the mechanical properties changed significantly by the desizing and gradually by the scouring, bleaching and dyeing processes.     

Synthesis of ZnO nanoparticles by PNP and its application on the functional finishing of cotton fabrics

This paper presents a facile and novel approach for the synthesis of ZnO nanoparticles in aqueous solution based on a one-step reaction between a modified hyperbranched polymer (PNP) and zinc nitrate. The prepared ZnO nanoparticles polymeric hybrid was characterized and its antibacterial activity was investigated. The results indicated that the ZnO nanoparticles have an average size about 6 nm and well dispersed in aqueous medium. The minimum inhibitory concentration (MIC) of them was 20 ppm and 60 ppm against S. aureus and E. coli, respectively. For the functional finishing of cotton fabrics by these ZnO nanoparticles, a microwave assisted in situ fabrication method was employed. Scanning electron microscope (SEM), energy dispersive X-ray (EDX) spectroscopy and X-ray diffraction (XRD) measurements confirmed that the ZnO nanoparticles in situ generated in cotton fabrics successfully. Fourier transform infrared (FT-IR) spectroscopic investigation demonstrated that the ZnO nanoparticles were fixed on the cotton fibers by PNP. The treated cotton fabrics exhibited excellent UV protective properties and antibacterial activities. When ZnO content of cotton fabric was 1.49 %, the UPF value of treated cotton fabric exceeded 125 and the bacterial reduction rate against S. aureus and E. coli reached 99.97 % and 98.40 %, respectively.     

A study of metal oxide on antimicrobial effect of plasma pre-treated cotton fabric

Cotton, a natural fibre that consists of cellulose, is highly popular because it is sweat-absorbing and comfortable to wear. However, cotton fabrics provide an excellent environment for microorganisms to grow, owing to their ability to retain moisture. Therefore, numerous chemicals have been used to enhance anti-microbial activity of cotton textiles. This paper reports results of use of silver oxide (Ag₂O) or zinc oxide (ZnO) as a catalyst in the antimicrobial formulation (halogenated phenoxy compound (Microfresh, MF)) and a binder (Microban, MB) for improved treatment of cotton fabrics and minimisation of side effects of the treatment. In addition, from the morphological study, plasma technology was employed to roughen the surface of the materials to improve loading of metal oxides on the surface. Moreover, the characteristic infra-red bands related to plasma-treated cotton produced results different from untreated fabric, implying plasma treatment can improve hydrophilicity of the fabric. Mechanical strength of the specimens was also increased by plasma treatment. Meanwhile, the research showed that the control fabric slightly inhibited the growth of S. aureus because of the bleach residues on fabric surface. On the other hand, anti-bacterial activity of MF-MB-treated specimen, especially in the presence of metal oxide catalyst, was enhanced, providing a slightly larger zone of inhibition. Moreover, plasma gas contains reactive oxygen species that can enter the cell, eventually causing its death. The hydrophilic nature of carbonyl groups present in oxygen plasma pre-treated specimens also increased the anti-microbial activity after treatment with MF-MB.     

Process technology and properties evaluation of a chitosan-coated Tencel/cotton nonwoven fabric as a wound dressing

A double-layer nonwoven fabric containing Tencel, cotton, and chitosan was prepared by the immersion-precipitation phase-inversion method and evaluated as a wound covering. Macroporous structure of the chitosan membrane could control evaporative water loss, promote fluid drainage, and inhibit exogenous micro-organisms invasion due to inherent antimicrobial property of the chitosan. The chitosan membrane was hemostatic and could accelerate the healing of the wound. Histological examination showed that epithelialization rate was increased and the deposition of collagen in the dermis was well organized by covering the wound with the membrane. These results indicate that the chitosan-coated Tencel/cotton nonwoven fabric can be a potential material employed as a wound dressing.     

The effect of the pretreatment print paste contents on colour yield of an ink-jet printed cotton fabric

Optimum condition concerning the content of pretreatment print paste and steaming time for ink-jet printing was newly developed through the orthogonal analysis. The cotton fabric treated under the newly developed optimum condition could achieve a high level of colour yield similar to that of the commercially pretreated cotton fabric available in the market for ink-jet printing. The results were discussed thoroughly in this paper.     

An extensive look into the effect of mercerization treatment on dimensional properties of cotton plain knitted fabric

Following our previous research [1], an extensive investigation on the effects of four mercerization treatment parameters namely, alkali concentration, time of treatment, bath temperature, and mercerization tension on dimensional properties of plain knitted fabric produced from cotton yarn is presented in this paper. Numerical values of constant geometry of the dry relaxed, wet relaxed, and mercerized samples were calculated according to Munden’s equations. Study shows that the area geometry constant values (K _s ) achieved after mercerization treatment was higher than values obtained for the samples subjected to dry and wet relaxations. Also, ANOVA test confirmed significant effects of each parameter itself and their interactions on dimensional properties of the fabric samples. Based on the results, applying less value of tension improves dimensional stability of the fabric but not for the samples mercerized in higher values of three other parameters. The alkali concentration had an optimum value in mercerization treatment. In mercerizing conditions carried out in high temperature and long time, lower alkali concentration is more efficient. Increasing time of treatment leads to achieve higher K _s value when lower value of alkali concentration is used. Most of the samples mercerized in bath temperature of 40 °C had the highest K _s . At the end of the research a statistical model was derived to predict the area geometry constant of the fabric.     

Prediction of the changes on the CIELab values of fabric after chemical finishing using artificial neural network and linear regression models

Changes on the CIELab values of the dyed materials after the different chemical finishing treatments using artificial neural network (ANN) and linear regression (LR) models have been predicted. The whole structural properties of fabrics and some process data which were from fiber to the finishing parameters were accepted as inputs in these models. The networks having different structures were established, and it was also focus on the parameters which could affect the performance of the established networks. It was determined that we could successfully predict the color differences values occurring on the material after the finishing applications. In addition, we realized that some ANN parameters affected the prediction performance while establishing the models. After training ANN models, the prediction of the color difference values was also tried by linear regression models. Then, extra ANN models were established for all outputs using the parameters as inputs in the LR equations, and the prediction performances of both established models were compared. According to the results, the neural network model gives a more accurate prediction performance than the LR models.