Surface modification of polyester fibers by thermal reduction with silver carbamate complexes

In this study, the surface of polyester fiber was modified by means of thermal treatment with a silver carbamate complex. We used scanning electron microscopy (SEM), an X-ray diffraction technique (XRD), and X-ray photoelectron spectroscopy (XPS) to allow a detailed characterization of the silver-coated polyethylene terephthalate (PET) fibers. The results revealed remarkable changes in the surface morphology and microstructure of the silver film after thermal reduction. On SEM, the silver nanoparticles (AgNPs) were seen to be uniformly and densely deposited on the fiber surface. The XRD pattern of the silver-coated fiber indicated that the film has a crystalline structure. A continuous layer of AgNPs, between 30 and 100 nm in size, was assembled on the PET fibers. The PET/Ag composite was found to impart high conductivity to the fibers, with an electrical resistivity as low as 0.12 kΩ·cm.     

Electrical conductivity and chromic behavior of poly (3-methylthiophene) — coated polyester fabrics

Electrically conductive substrates with chromic behavior are prepared using conductive polymer coating of the substrate. Poly (3-methylthiophene) (P3MT) — coated polyester fabric with specific electrical and chromic properties, for instance electrochromic and piezochromic behavior, was successfully obtained by chemical polymerization with the help of continuous and speed stirring technique. The effect of polymerization time, temperature and oxidant concentration on conductivity of the P3MT-coated fabric was studied. The presence of P3MT particles on the surface of the coated substrate was confirmed by scanning electron microscopy (SEM), fourier transform infrared (FTIR) and UV-Vis spectroscopy, electrical surface resistivity, pressure and applied voltage dependence visible reflectance spectrophotometer measurements, and X-ray diffraction (XRD) analysis. The blue shift of c95 nm in wavelength of maximum absorption observed in the reflectance spectra of coated polyester fabric. Under high pressure, the P3MT-coated polyester fabric demonstrated piezochromism. The coated substrate also showed electrochromic behavior under an electrical applied voltage of 12 V.     

Reduction of 4-nitrophenol to 4-aminophenol over sonoimmobilized silver/reduced graphene oxide nanocomposites on polyester fabric

The current paper is aimed to compare different arrangement of Ag nanoparticles within silver/reduced graphene oxide (Ag/rGO) nanocomposites on the polyester fabric. rGO sheets cannot be dispersed in the water for long time however, thin layer surfactant-free Ag/rGO nanocomposites were immobilized on the surface of polyester. This leads to attain the preserved array of nanocomposites for a long time. TEM, FESEM/EDX, XRD, XPS, cyclic voltammetry, catalytic activity and electrical resistivity were used to characterize Ag/rGO nanocomposites coated polyester fabric. Interestingly, sonoimmobilization of Ag/GO produced an even coating layer of nanocomposites on the polyester fabric. The prepared fabric can be used as a high active and stable nanocatalyst for reduction of 4-nitrophenol (4-NP) in water at room temperature. The created flexible and light fabric showed low electrical resistance and high catalytic activity, wherein sonoimmobilization of Ag/rGO treated samples indicated highest catalytic activity as 4-NP solution completely reduced to 4- AP with assistance of 2×4 cm2 treated polyester after 25 min. On the other hand, introducing sonoprepared silver nanoparticles among graphene nanosheets led to significant lowering of electrical resistivity from 43 kΩ/square in mechanical stirring methodto 2 kΩ/square using ultrasound.     

Effect of polyester fabric through electroless Ni-P plating

Process for electroless nickel-phosphorous (Ni-P) plating has been investigated as a metallizing treatment technology on polyester fabric. The microstructure and mechanical performance of Ni-P-plated polyester fabric are investigated in this study. Surface modifications of Ni-P-plated polyester fiber were studied by scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX) and X-ray diffraction (XRD). The changes in weight and thickness of the Ni-P-plated polyester fabric were determined through direct measurements. Systematic investigations, including bending rigidity, tearing strength, tensile strength, elongation at break, air permeability, wettability and absorbency, and anti-static property were conducted on untreated and metallized polyester fabrics. A thorough discussion and quantitative report were made on the specific performance of the Ni-P-plated polyester fabric.     

Improved interfacial properties of carbon fiber/unsaturated polyester composites through coating polyhedral oligomeric silsesquioxane on carbon fiber surface

Carbon fibers were coated with E51 plus Methacryl-POSS together in an attempt to improve the interfacial properties between carbon fibers and unsaturated polyester resins matrix. Atomic force microscopy (AFM), scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS) were performed to characterize the changes of carbon fiber surface. AFM results show that the coating of E51 plus POSS significantly increased the carbon fiber surface roughness. XPS indicates that silicon containing functional groups obviously increased after modification. Dynamic mechanical analysis was carried out to investigate the surface energy of carbon fiber. Force modulation atomic force microscopy (FMAFM) and Interlaminar shear strength (ILSS) were used to characterize the interfacial properties of the composites. ILSS was increased by 21.9 % after treatment.     

Preparation and photocatalytic activity of bismuth tungstate coated polyester fabric

Bi₂WO₆ particles were prepared and then coated on the polyester fabric. Surface morphology, crystal structure, and chemical structure of the Bi₂WO₆ particle coated polyester fabric were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), and Fourier transform infrared spectroscopy (FTIR). Photocatalytic activity was evaluated by the degradation of methylene blue (MB) under ultraviolet light irradiation. Influences of the different concentrations of Bi₂WO₆ on the deposit weight and the photocatalytic activity of the Bi₂WO₆ particle coated polyester fabric were investigated. In addition, UV protection of the Bi₂WO₆ particle coated polyester fabric was examined. The results show that Bi₂WO₆ particles are uniformly coated on the surface of the polyester fabric. The Bi₂WO₆ particles coated on the polyester fabric are irregular and are orthorhombic. In addition, the Bi₂WO₆ particle coated polyester fabric exhibits excellent photocatalytic activity and UV protection. The average degradation efficiency of MB in the presence of the Bi₂WO₆ particle on the polyester fabric coated with 10 g/l Bi₂WO₆ reaches 98.6 % after being illuminated for 7 h. Therefore, the Bi₂WO₆ particle coated polyester fabric shows excellent photocatalytic stability for dyes degradation.     

Tunable functional properties on polyester fabric using simultaneous green reduction of graphene oxide and silver nitrate

Here, a novel method is introduced to create tunable properties on the polyester fabric through diverse chemical modifications. The polyester fabric was primarily modified with NaOH or ethylenediamine to enhance the surface activity. This will produce diverse chemical groups on the polyester fabric surface including carboxylate, hydroxyl and amine groups. The fabric was treated with grahene oxide through exhaustion method. The silver nitrate was then added and simultaneously reduced with grapheme oxide using ascorbic acid and ammonia to produce reduced graphen oxide/silver nanocomposites (rGO/Ag) on the fabric surface. The synthesized nanocomposites were characterized by TEM and Raman spectra. The presence and uniform distribution of the nanocomposites on the fabric surface was also confirmed by SEM images and EDX patterns. The electrical resistivity was varied on the raw and modified polyester fabric due to the diverse formation of the graphene nanosheets network on the fabric surface. More Ag particles were formed on the surface of the alkali hydrolyzed polyester whereas more graphene nanosheets deposited on the aminolyzed polyester fabric. Also the hydrolyzed polyester fabric exhibited higher antibacterial properties with the lowest silver nitrate in the processing solution. The aminolyzed fabric showed a lower electrical resistance than the hydrolyzed and raw fabrics with the same amount of GO in the procedure bath. The aminolyzed polyester fabric indicated higher affinity towards GO produced higher antibacterial properties before reduction and without silver nitrate however lower electrical resistance obtained after reduction comparing with other samples.     

Screen printed silver patterns on functionalised aramid fabric

In this work, a simple and low cost method based on screen printing is presented to synthesize a conductive silver pattern on aramid fabric. The aramid fiber was treated with (3-mercaptopropyl)-trimethoxysilane to introduce a tail mercapto group promoting the ordered binding of silver nanoparticles. SEM and AFM images indicated a uniform distribution of silver nanoparticles on fiber surface. FTIR and XRD patterns confirmed the silver layer on the fibers. Furthermore, the electrical property of conductive fiber was characterized by conductive AFM and a digital multimeter, the surface resistance of conductive fabric was as low as 0.20 Ω/cm. And single fiber tensile test indicated that the mild treating process has no significant influence on the mechanical properties of the fiber.     

Photo-thermal conversion and thermal insulation properties of ZrC coated polyester fabric

Zirconium carbide (ZrC) films are deposited onto polyester fabric through magnetron sputtering. The deposited films are then examined by using field scanning electron microscopy and energy dispersive X-ray spectroscopy. The photothermal conversion property, film thickness, infrared reflectance and transmittance, and thermal conductivity are also evaluated. The results show that the highest far-infrared emissivity of polyester fabric deposited with ZrC is 0.9379. The ZrC deposited samples showed a small increase in thermal conductivity with a difference of 0.0611W/m·K, and a higher photothermal conversion efficiency with a temperature increase of 27.5 °C in 100 s, when the thickness of the ZrC film is 1920 nm. These therefore indicate that coating fabrics with ZrC through magnetron sputtering is an environmentally friendly means to produce textiles with photo-thermal conversion and heat insulation properties.     

Film morphology of supramolecule CPES/ASO and its performance on cotton substrates

The supramolecule CPES/ASO was self-assembled from carboxylated polyether-block-polydimethylsiloxane (CPES) and N-β-aminoethyl-γ-aminopropyl polysiloxane (ASO) in ethyl acetate solution. The film morphology and performance of CPES/ASO on cotton substrates were investigated by field emission scanning electron microscope (FESEM), atomic force microscope (AFM), X-ray photoelectron microscope (XPS), and so on. The results indicated that a polysiloxane resin film was coated on the treated fiber surface and able to decrease the root mean square roughness (R _q ) of the treated fiber conspicuously. Morphology of higher peaks circled by many smaller peaks was observed on the film surface, which was partly similar to that of CPES/ASO on the silicon wafer. Besides, when the mass ratio of CPES to ASO was 2:1, the fabric treated by CPES/ASO showed the best softness and had a comfortable oily tactile.     

Adhesion and durability of Cu film on polyester fabric prepared by finishing treatment with polyester-polyurethane and aqueous acrylate

To improve adhesion and wear durability at the interface between copper (Cu) film and polyester fabric, the Cu-coated polyester fabric was treated by two commercial solutions of polyester-polyurethane (PP) and aqueous acrylate (AC) as finishing process respectively. Both finishing agents with 5 %, 10 %, 15 %, 20 %, 25 %, 30 %, 35 % and 40 % concentrations were coated on the Cu-coated fabrics by a padding method in this study. The surface morphologies of the coated polyester fabric before and after finishing were characterized by scanning electron microscopy (SEM). The adhesion of Cu-coated film before and after the finishing treatments was measured with scotch tape method; the durability was evaluated by colorfastness to washing, crocking and perspiration. Additionally, Ultraviolet (UV) shielding, water repellency and CIE L*a*b of the Cu-coated polyester fabric before and after the finishing treatments were determined. The Cu-coated polyester fabric has a high adhesion property of the 5 level, colorfastness to washing, wet crocking and perspiration of the Cu-coated fabric were obviously enhanced to level 5, level 4-5 and level 3-4. Meanwhile, The Cu-coated polyester fabric kept an excellent UV protection with UPF value over 68 after finishing treatment with PP and AC. The results demonstrate the finishing treatment with the PP presented effectively in durability performance than the AC for the Cu-coated polyester fabric.     

Facile fabrication of superhydrophobic cotton fabric from stearyl methacrylate modified polysiloxane/silica nanocomposite

The stearyl methacrylate modified polysiloxane/nanocomposite was synthesized by graft copolymerization between stearyl methacrylate modified polysiloxane with pendent epoxy groups and amino-functionalized nano silica. Then it was utilized to fabricate the superhydrophobic cotton fabric by one-step method. The structures, chemical compositions, thermal properties, surface morphology and wettability were characterized by Fourier Transform Infrared Spectrum (FT-IR), X-ray photoelectron spectroscopy (XPS), Thermo-gravimetric analyzer (TGA), Scanning electron microscopy (SEM) and Static contact angle analyzer. Results showed that a hydrophobic polysiloxane film and many nano-scaled tubercles were coated on the surface of the treated cotton fabrics plus their inherent microscaled roughness, which were the reasons why cotton fabric changed from hydrophilicity to hydrophobicity. In addition, with increase of the amount of nanocomposite, hydrophobicity of the treated cotton fabric would be enhanced; water contact angle of this fabric could attain 157°, which was higher than 141.5° reached by the fabric treated with stearyl methacrylate modified polysiloxane. The superhydrophobic cotton fabric also possessed favorable washing durability. On the other hand, its air permeability, color and softness would not be influenced instead.     

Surface characterization of aromatic thermotropic liquid crystalline fiber deposited by nanostructured silver

Nanostructured silver thin films were sputtered onto the aromatic thermotropic liquid crystalline fibers of Vectran by magnetron sputtering technology. Plasma treatment was used as pre-treatment in order to improve the deposition of the coating layer. Surface morphology of the coated fibers was examined by scanning electron microscopy (SEM) and atomic force microscopy (AFM). A full energy dispersive X-ray analysis (EDX) was used to detect the elemental composition of the material. Its conductivity and mechanical properties were measured and analyzed as well. The study revealed that a very thin conductive silver deposition exhibited high electrical conductivity as well as less influence on the mechanical properties of the pre-treated Vectran fiber. The plasma treatment could improved the deposition of the coating layer, but the surface roughness caused by plasma treatment also affected the surface conductivity. It was found that the surface resistivity could reach very low value of 1.66×10⁻³ Ω·cm after sputtering deposition for 30 min.     

Application of silver nanoparticles to cotton fabric as an antibacterial textile finish

A novel nano-silver colloidal solution was prepared in one step by mixing AgNO₃ aqueous solution and an amino-terminated hyperbranched polymer (HBP-NH₂) aqueous solution under vigorous stirring at room temperature. All results of Dynamic Light Scattering (DLS), Transmission Electron Microscopy (TEM) and UV/Visible Absorption Spectrophotometry indicated that silver nanoparticles had been formed in colloidal solution. Cotton fabric was treated with nano-silver colloid by an impregnation method to provide the cotton fabric with antibacterial properties. The whiteness, silver content, antibacterial activity and washing durability of the silver-treated fabrics were determined. The results indicated that the silver-treated cotton fabric showed 99.01 % bacterial reduction of Staphylococcus aureus and 99.26 % bacterial reduction of Escherichia coli while the silver content on cotton was about 88 mg/kg. The antimicrobial activity of the silver-treated cotton fabric was maintained at over 98.77 % reduction level even after being exposed to 20 consecutive home laundering conditions. In addition, the results of scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS) confirmed that silver nanoparticles have been fixed and well dispersed on cotton fabrics’ surface and the major state of the silver presented on the surface was Ag⁰.     

Polyester metallisation with electroless silver plating process

In this paper, electroless silver plating process for polyester was reported. The electroless silver plating is basically divided into four stages including pre-cleaning, sensitisation, electroless silver deposition and post-treatment. As the electroless silver plating stage is the key stage in affecting the brilliant appearance and various functional properties such as conductivity and ultra-violet protection, we will study the effect of process variables, i.e. amount of silver nitrate (AgNO₃), concentration of ammonium hydroxide (NH₄OH), concentration of sodium hydroxide (NaOH) and process temperature, using increased amount of silver in fabric surface as an indicator, for optimising the electroless silver plating process for possible industrial application. Experimental results revealed that amount of silver nitrate (AgNO₃)=1.77×10^?3 mole; concentration of ammonium hydroxide (NH₄OH)=6.25 %; concentration of sodium hydroxide (NaOH)=0.008 g/ml and process temperature=25 °C can give the best electroless silver plating for polyester fabric. The surface characteristics of the electroless silver-plated polyester fabric were evaluated by scanning electron microscope, X-ray photoelectron spectroscopy and X-ray diffraction analysis. Meanwhile, the performance properties of the electroless silver-plated polyester fabric were measured by CIE L*, a* and b* values, conductivity as well as ultraviolet protection. The experimental results would be discussed thoroughly in this paper.     

Antibacterial properties of PLA nonwoven medical dressings coated with nanostructured silver

In this paper, magnetron sputtering was applied to deposit nano-structured silver films on the surfaces of polylactic acid (PLA) nonwovens, which were used in medical dressings. The influence of the coating thickness of the nano-structured sliver films on the antibacterial property of the nonwovens was studied. The antibacterial properties of the medical dressings were measured by shake flask test. The surface morphology of nano-structured silver films and the grain sizes of silver agglomerates were analyzed by atomic force microscope (AFM). Energy dispersive X-ray (EDX) was employed to analyze the surface elemental compositions. The study revealed that the antibacterial properties were improved as the film thickness increased. AFM images of the coated samples indicated that as the sputtering time prolonged, the film thickness was increased, the film became compacter, and the specific area of the film was also increased. Thus, the release rate of silver ions increased, leading to the improved antibacterial property. It was found that the reduction percentage of both tested bacteria-Staphylococcus aureus and Escherichia coli reached 100 % as the coating thickness exceeded 1 nm.     

Synthesis of silver nanoparticles with sericin and functional finishing to cotton fabrics

This research presents a novel strategy to fabricate multi-functional cotton textiles. In this study, silver nanoparticles-sericin (Ag NPS-sericin) hybrid colloid has been prepared using sericin as reducing agent and dispersing agent. Cotton fabrics was oxidized selectively with sodium periodate (NaIO₄) to generate oxidized cotton fabrics, and which has then been finished using Ag NPS-sericin hybrid colloid prepared to obtain multi-functional cotton textiles. The finished cotton fabric not only possessed excellent antibacterial activity, but also it was modified functionally by sericin protein, which endowed antibacterial cotton fabrics relatively smooth surface and good wear ability. Fourier transform infrared spectrogram confirmed that sericin protein was grafted onto cellulose fibers. Ag NPs were characterized by UV-Vis spectroscopy, transmission electron microscope (TEM) and X-ray powder diffraction (XRD). The results of SEM, X-ray photoelectron spectroscopy (XPS) and EDS confirmed that silver nanoparticles and sericin been loaded successfully on the surface of cotton fabrics. The antibacterial experiments showed bacterial reduction rates of S.aureus and E.coli were able to reach above 99 %. After washing 20 times, it showed still good antibacterial activity at over 95 % against S.aureus and E.coli.     

Effect of surface treatment on the structure and properties of para-aramid fibers by phosphoric acid

The surface of para-aramid fiber was modified by phosphoric acid solutions (H3PO4) based on an orthogonal experimental design and analysis method. Statistical results indicate that treatment temperature is the most significant variable in the modification processing, while treatment time was the least important factor. The structure and morphology of the modified fiber were characterized by Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), X-ray diffraction instrument (XRD), and scanning electron microscope (SEM). The results showed that some polar groups were introduced into the molecular structure of aramid fibers and the physical structure of the treated fibers was not etched obviously. The interfacial properties of aramid fiber/epoxy composites were investigated by the single fiber pull-out test (SFP), and the mechanical properties of aramid fibers were investigated by the tensile strength test. The results showed that the interfacial shear strength (IFSS) of aramid/epoxy composites was remarkably improved and the breaking strength of aramid fibers was not affected appreciably after surface modification.     

Surface treatments of jute fabric: The influence of surface characteristics on jute fabrics and mechanical properties of jute/polyester composites

In this study, jute fabrics were modified by alkali, micro-emulsion silicon (MS) and fluorocarbon based agents (FA) in order to enhance the interfacial adhesion between the polyester matrix and the jute fiber. X-ray photoelectron spectroscopy (XPS) and contact angle measurements were used to characterize fiber surfaces. The effects of various surface treatments on the mechanical and morphological of jute/polyester composites were also studied. All surface treatments were shown to improve the tensile, flexural strengths and interlaminar shear strengths of the composites. Moreover, the maximum improvement in the mechanical properties was obtained for the FA treated jute/polyester composites. SEM micrographs of the tensile fracture surface of jute/unsaturated polyester composites also exhibited improvement of interfacial and interlaminar shear strengths by the alkali, MS and FA treatments of jute fibers.     

Preparation of electroconductive,magnetic, antibacterial,and ultraviolet-blocking cotton fabric using reduced graphene oxide nanosheets and magnetite nanoparticles

The main goal of present study was the fabrication of cotton fabric with special functions, including electrical conductivity, magnetic, antibacterial, and ultraviolet (UV) blocking. In this regard, the cotton fabric was primarily coated with graphene oxide and then reduction of graphene oxide and synthesis of magnetite nanoparticles accomplished in one step. The alkaline hydrolysis of magnetite precursors and reduction of graphene oxide was simultaneously performed using sodium hydroxide to produce reduced graphene oxide/Fe₃O₄ nanocomposite on the fabric surface. The prepared cotton fabrics were characterized with field emission scanning electron microscope (FE-SEM), X-ray diffraction (XRD), energy dispersive X-ray spectroscopy (EDS), and X-ray photoelectron spectroscopy (XPS). The treated fabrics with reduced graphene oxide/Fe₃O₄ nanocomposite displayed a low electrical resistivity i.e. 80 kΩ/sq. Furthermore, the coated fabrics showed reasonable magnetic properties due to the presence of magnetite nanoparticles on the surface of cotton fabrics. Moreover, this process imparted proper antibacterial properties and UV blocking activity to cotton samples.