ACQ防腐剂对扭叶松蓝变部分木材力学性能的影响

本文利用三种不同浓度ACQ防腐剂对扭叶松蓝变木材进行浸注处理,其浓度分别为1.2%、2.0%和2.8%.研究其抗弯弹性模量、抗弯强度、冲击韧性和顺纹剪切强度(弦面)与未处理蓝变木材相应力学性能的差异,测试标准参照GB1927～1943-91.研究结果显示,经浸注处理后的试样均达到美国AWPA标准UC4A等级规定的药剂保持量;ACQ防腐处理大约降低了20%扭叶松蓝变木材的冲击韧性,与未防腐处理试样对比,在0.01水平上有显著差异,但不同浓度间差异不显著;三种浓度ACQ处理间以及与未处理的扭叶松蓝变木材的抗弯强度、抗弯弹性模量和顺纹剪切强度差异不显著;随着ACQ浓度的降低,冲击韧性、抗弯强度、抗弯弹性模量和顺纹弦面剪切强度有所增大,但影响都很小.图4表10参6.     

扭叶松实木板材三种动态弹性模量和静态弹性模量比较研究(英文)

采用Pundit、Metriguard、FFT等三种无损检测方法和常规弯曲法对加拿大扭叶松(lodgepole pine)蓝变与非蓝变实木板材的动态及静态弹性模量进行检测和比较研究。结果表明,蓝变材三种动态弹性模量及静态弹性模量均高于非蓝变材;对比分析表明,蓝变材和非蓝变材的动态及静态弹性模量存在差异,其中动态弹性模量差异均达到0.01显著性水平,静态弹性模量差异达到0.05显著性水平,并且心、边材及密度值不同是导致以上差异的主要原因。相关性分析表明,动态与静态弹性模量间相关性达到0.01显著性水平;尽管三种无损检测方法测量结果存在差异,但它们之间仍存在密切相关性,FFT 技术测量的准确性高于Pundit和Metriguard;板材中结子数影响木材动态和静态弹性模量,随着板材结子数增加弹性模量相应地降低。     

Comparative study on three dynamic modulus of elasticity and static modulus of elasticity for Lodgepole pine lumber

The dynamic and static modulus of elasticity （MOE） between bluestained and non-bluestained lumber of Lodgepole pine were tested and analyzed by using three methods of Non-destructive testing （NDT）, Portable Ultrasonic Non-destructive Digital Indicating Testing （Pundit）, Metriguard and Fast Fourier Transform （FFT） and the normal bending method. Results showed that the dynamic and static MOE of bluestained wood were higher than those of non-bluestained wood. The significant differences in dynamic MOE and static MOE were found between bulestained and non-bluestained wood, of which, the difference in each of three dynamic MOE （Ep. the ultrasonic wave modulus of elasticity, Ems, the stress wave modulus of elasticity and El, the longitudinal wave modulus of elasticity） between bulestained and non-bluestained wood arrived at the 0.01 significance level, whereas that in the static MOE at the 0.05 significance level. The differences in MOE between bulestained and non-bluestained wood were induced by the variation between sapwood and heartwood and the different densities of bulestained and non-bluestained wood. The correlation between dynamic MOE and static MOE was statistically significant at the 0.01 significance level. Although the dynamic MOE values of Ep, Em, Er were significantly different, there exists a close relationship between them （arriving at the 0.01 correlation level）. Comparative analysis among the three techniques indicated that the accurateness of FFT was higher than that of Pundit and Metriguard. Effect of tree knots on MOE was also investigated. Result showed that the dynamic and static MOE gradually decreased with the increase of knot number, indicating that knot number had significant effect on MOE value.     

Physical and mechanical properties of wood after moisture conditioning

Some properties of wood (hinoki:Chamaecyparis obtusa) moisture-conditioned by an adsorption process from a dry state and by two desorption processes (from a water-saturated state and from a state with a moisture content slightly below the fiber saturation point) were investigated. The moisture contents of wood conditioned by the adsorption process and by the desorption process continued to approach to one another for the moisture-conditioning period of over 50 weeks. Accordingly, sorption hysteresis should be regarded as a transitional phenomenon that occurs during the process of approaching the true equilibrium, which requires a long time. The wood conditioned by the desorption process beginning from a water-saturated state showed slightly smaller dimensions than those conditioned by the adsorption process with the same moisture content; however, the wood conditioned by the desorption process from a moisture content below the fiber saturation point showed slightly larger dimensions than those conditioned by the adsorption process. The wood conditioned by the adsorption process from a dry state showed a higher modulus of elasticity and modulus of rupture than did the wood conditioned from a water-saturated state with the same moisture content. The mechanical properties of the wood also varied based on the states at which the desorption process was started. This is a notable characteristic of the relation between the drying condition and the mechanical properties of wood.     

Changes in the mechanical properties of wood during a period of moisture conditioning

Changes in the modulus of elasticity (MOE), modulus of rupture (MOR), and stress relaxation in the radial direction of wood (hinoki:Chamaecyparis obtusa) moisture-conditioned by the adsorption process from a dry state and by the desorption process from a moisture content slightly below the fiber saturation point were investigated. The MOE and MOR of wood conditioned by the adsorption process showed significant increases during the later stages of conditioning when the moisture content scarcely changed. However, with the desorption process they did not increase as much during later stages of conditioning, though they increased during early stages of conditioning when the moisture content greatly decreased. The stress relaxation of wood decreased with an increase in the conditioning period with both the adsorption and desorption processes. These results suggest that wood in an unstable state, caused by the existing state of moisture differed from that in a true equilibrium state shows lower elasticity and strength and higher fluidity than wood in a true equilibrium state. Furthermore, the present study demonstrates that the unstable states of wood induced during the course of drying, desorption, and possibly adsorption of moisture are slowly modified as wood approaches a true equilibrium state.     

COMPARATIVE STUDY OF WOOD PROPERTIES BETWEENWHITE WOOD OF DAHURIAN LARCH AND MONGOLIANSCOTCH PINE

DahurianlarchandMongolianscotchpinearetwomajorconunerciaIconilbroustTeesinDaxing'anlingForesnyArea.Itisob-viousthattbcwoodproPertiesandworkability'ofthetWoplantsarecompletelydifferent.Butlnrecert'years,ltlsfoundthattherearetwodiffer':nttypesinparameterofwood'scolour.phy'sicalandmechanicalproPertiesandwork-ability'inDahurianlarch,namelyredwoodandx"hite..od.l']Andthepropertiesofwhite`voodaresligl1tlyyellow-white,medianweightandhardness,goodinworkability'andLard-ness,goodinwodability'anduneas…     

ACQ各组分对金属腐蚀性的影响

测定ACQ各组分对4种金属的腐蚀性。结果表明,除304不锈钢以外,ACQ对其余3种金属均有较强的腐蚀性;二甲基双癸基氯化铵(DDAC)中的氯离子,是影响ACQ对Q235A钢腐蚀性的主要因素;CuO质量分数和CuO与DDAC的质量比,是影响ACQ对Q235A钢腐蚀性的显著因素。     

Influence of fire and mountain pine beetle on the dynamics of lodgepole pine stands in British Columbia,Canada

An outbreak of the mountain pine beetle (Dendroctonus ponderosae Hopkins; MPB), currently affecting over 10.1 million hectares of lodgepole pine forests (Pinus contorta Dougl.) in British Columbia, Canada, is the largest in recorded history. We examined the dynamics of even-aged lodgepole pine forests in southern British Columbia, which were undergoing this MPB outbreak. Using dendroecology and forest measurements we reconstructed the stand processes of stand initiation, stand disturbances, tree mortality, and regeneration, and explained the current stand structure and the potential MPB impacts in selected stands. Our results indicate that stand-replacing fires initiated even-aged seral lodgepole pine stands in this region. In the absence of fire in the 20th century, multiple MPB disturbances, which each resulted in partial canopy removal, modified the simple one-layer structure of the fire-origin stands by the initiation of post-MPB disturbance regeneration layers, transforming the stands into complex, multi-aged stands. Despite high overstory mortality due to the current MPB outbreak, regeneration layers, which are likely to survive the current outbreak, will provide important ecological legacies and will contribute to mid-term timber supply.     

Characterization of major,unused, and unvalued Indonesian wood species I. Dependencies of mechanical properties in transverse direction on the changes of moisture content and/or temperature

Mechanical property changes due to the moisture content (MC) and/or temperature changes were examined for 15 Indonesian wood species. A static bending test was carried out at 20°C, 65% relative humidity (air-dry), and water-saturated at 20°C (wet-20) and 80°C (wet-80). For individual test conditions, modulus of elasticity (MOE) and modulus of rupture (MOR) increased linearly with specific gravity regardless of wood species; however, maximum deflection did not correlate with specific gravity for any MC or temperature conditions. The relative values of MOE and MOR measured in wet-20 to air-dry conditions were variously affected from slightly to strongly depending on the wood species. However, the relative values always decreased markedly when saturated in water at 80°C, regardless of wood species. The relative MOE, MOR, and maximum deflection values due to the change in MC or MC and temperature combined were independent of specific gravity but may be dependent on wood type: softwood or hardwood.     

日本松材线虫病研究的最新动向

该文重点对近2a日本松材线虫病的研究文献进行整理分析。目前松材线虫病的研究仍是日本国森林病虫害的主要研究课题。在松树的抗（感）病机理、线虫在树体内的活动与增殖规律、线虫与天牛的关系、生物防治以及新技术在研究中的应用等方面取得较大进展。     

人工林落羽杉力学性能研究

对江汉平原人工林落羽杉物理力学性能进行了研究,结果表明:落羽杉的气干密度为0.413 g/cm3,气干密度等级为轻;综合强度为74 MPa,强度等级为Ⅰ级;径向横纹抗压强度略大于弦向横纹抗压强度;端面硬度最高,弦面硬度与径面硬度差别不大。落羽杉南北面近树皮处木材的密度、抗弯强度、弹性模量、顺纹抗压强度均大于近髓心处,南北方向对落羽杉的密度、顺纹抗压强度在5%水平上差异均不显著,而对其抗弯强度、弹性模量在1%水平上差异显著。     

松材线虫发病条件的研究概况

研究和综述了寄生松科植物的伞滑刃属(Bursaphelenchus)的线虫23种,松材线虫的寄主松科植物108种、携带昆虫40种及发病的环境条件。     

Orthotropic hygric and mechanical material properties of oak wood

The present study examines the three-dimensional hygric and mechanical behavior of oak wood. The moisture equilibrium state, characterized by the sorption isotherms, was obtained from measurements taken during adsorption and desorption cycles. Sorption behavior was analyzed with the Dent theory and compared considering the sorption direction (adsorption/desorption cycle). Sorption parameters were provided for possible numerical applications in hygric material models. The corresponding swelling and shrinkage behavior was examined and characterized by the moisture expansion parameters for all anatomical directions. Orthotropic mechanical material behavior was characterized by determining the elastic engineering (Young's moduli, shear moduli, and Poisson's ratios) and the bending, compressive and compressive shear strength material parameters. Influence of moisture content (MC) on the mechanical material properties was studied using Young's moduli, Poisson's ratios, and the investigated strength parameters. A significant difference between the sorption behavior in adsorption and desorption, known as the hysteresis effect, could be proved. Furthermore, swelling and shrinkage behavior did not show any dependency on the adsorption/desorption cycle. The results confirm the significant influence of MC on the Young's moduli and the strength properties, however, did not validate an influence on the Poisson's ratios.     

STUDIES ON PHYSICAL AND MECHANICAL PROPERTIES OF DAHURIAN LARCH-WOOD OF TWO WOOD COLOURS

Dahurian1arch[Larixgmelini(Rupr.)Rupr.jisamaintimbertreespe-ciesinDaxing'anLingForestRegion,and'itisalsoafast-growingandregenerationtreeinNorthChina-Becauseitsecologicalamplitudeisverywild,therearemanyva-riabletypesinvarioushabitats.Themostsignificativetypes,whichhavebeenfoundrecentlyininvestigation,aretheredwoodandwhitewood.Theformerisfromyellow-browntored-brown,andthelat-tCrisfrompaleyellowtowhite.Theyaresimilarto'Redscotchpine#and'Whitescotchpine#.Theparametersofwoodcol-ourandphysico-…     

Influence of biotic factors on the mechanical properties of wood,taking into account the time of harvesting

The aim of the present paper is to investigate the influence of biotic factors (fungi and insects) on the mechanical properties of wood through the effect of blue-stain, taking into account the time of harvesting and the time of stay of wood in the forest. Specifically, the resistance to axial compression and to bending (modulus of rupture (MOR)) was studied using infected specimens of Scots Pine (Pinus sylvestris) and Norway Spruce (Picea abies) (the usual types of wood used in woodwork). The specimens were obtained from logs of Scots Pine and Norway Spruce that were harvested in three different seasons of year, namely in July 2012, November 2012 and June 2013, respectively, in the forest of Elatia-Greece, and the attack pace by biotic factors with respect to the time of logging was studied. The placement of the experimental surfaces of each type of tree was made on skid road and in the stand. Totally, 120 laboratory measurements in axial compression and 120 measurements in bending (MOR) took place. The results proved that blue-stain hardly affect the mechanical properties of both wooden species and particularly the specimens that were derived during the winter logging.     

Selected physical and mechanical properties of the Chilean wood species roble,lingue, manio and alerce

Abstract

Data sets with mechanical and physical properties of wood species can aid the recognition of biomechanical correlations, and they can also be valuable tools to assist decision making regarding the practical industrial employment of the species. However, such data sets are still lacking for many species, particularly non-European and non-North-American species. Therefore, the goal of this study was to determine the mechanical properties of four Chilean species (the softwoods alerce and manio, and the hardwoods lingue and roble), including the three Young's moduli and the three shear moduli. Dynamic methods were applied as well as static ones. The results suggest that Brinell hardness, compression strength and Young's moduli are clearly correlated with the density and can partly be related to anatomical details. Since the investigated species cover only a fraction of the Chilean species that are suitable for construction purposes, for example, further future examination of relevant species would be beneficial for basic research and industry.     

杨树溃疡病及松材线虫病对树体干部电指标的影响

对杨树溃疡病及松材线虫病对树木电指标的影响进行研究.结果表明:杨树溃疡病胁迫下,毛白杨扦插苗POD酶活性先增大后减小,PPO酶活性持续增大,树木干部电容和单位电容呈减小趋势,而树木干部阻抗呈增大趋势,最先表现出统计学差异性的指标是POD酶活性,其次为树木干部电容,之后为树体干部阻抗,最后是PPO酶活性;树木干部电容和单位电容与马尾松枯针率均有显著的正相关关系,同时利用树体干部电容0.5 nF为阈值,判断马尾松是否感染松材线虫的准确率可达89.26%.     

Effect of fungal exposure on the strength of thermally modified Norway spruce and Scots pine

Abstract

Thermal modification at elevated temperatures changes the chemical, biological and physical properties of wood. In this study, the effects of the level of thermal modification and the decay exposure (natural durability against soft-rot microfungi) on the modulus of elasticity (MOE) and modulus of rupture (MOR) of the sapwood and heartwood of Scots pine and Norway spruce were investigated with a static bending test using a central loading method in accordance with EN 408 (1995). The results were compared with four reference wood species: Siberian larch, bangkirai, merbau and western red cedar. In general, both the thermal modification and the decay exposure decreased the strength properties. On average, the higher the thermal modification temperature, the more MOE and MOR decreased with unexposed samples and increased with decayed samples, compared with the unmodified reference samples. The strength of bangkirai was least reduced in the group of the reference wood species. On average, untreated wood material will be stronger than thermally modified wood material until wood is exposed to decaying fungi. Thermal modification at high temperatures over 210°C very effectively prevents wood from decay; however, strength properties are then affected by thermal modification itself.     

Effects of impregnation and heat treatment on the physical and mechanical properties of Scots pine (Pinus sylvestris) wood

Wood modification, of which thermal modification is one of the best-known methods, offers possible improvement in wood properties without imposing undue strain on the environment. This study investigates improvement of the properties of heat-treated solid wood. Scots pine (Pinus sylvestris) was modified in two stages: impregnation with modifiers followed by heat treatment at different temperatures. The impregnation was done with water glass, melamine, silicone, and tall oil. The heat treatment was performed at the temperatures of 180°C and 212°C for three hours. The modified samples were analyzed using performance indicators and scanning electron microscope micrographs. The mechanical and physical properties were determined with water absorption, swelling, bending strength, and impact strength tests. All the modifiers penetrated better into sapwood than hardwood; however, there were significant differences in the impregnation behavior of the modifiers. As regards the effect of heat treatment, generally the moisture properties were improved and mechanical strengths impaired with increasing treatment temperature. In contrast to previous studies, the bending strength increased after melamine impregnation and mild heat treatment. It is concluded that the properties of impregnated wood can be enhanced by moderate heat treatment.     

马尾松纸浆林造林密度对木材性质的影响

本文研究了龙里林场5种造林密度，15年生马尾松纸浆林木材基干密度和管胞形态。结果表明：造林密度对木材基本密度影响不大，但具明显的趋势，即一定造林密度条件下，木材基本密度随造林密度增加而增加，造林密度对管胞形态的影响，表现出因年龄而异，不同造林密度马尾松管胞形态总平均值变化不大，但管胞长度随树龄的增大而增加的趋势，受到造林密度影响，较低的造林密度各生长轮管胞形态差异不显著。管胞长度频率分布具一定的规律，中等长度（2501－3500um)管胞长度频率分布最大，占总频率的45％－74．19％，随着造林密度加大，中等长度的管胞增加，较短管胞长度（≤2500um)减少。