Measurement of the shearing properties of wood by in-plane shear test using a thin specimen

In this research, in-plane shear tests were conducted for obtaining the shearing properties of wood. Thin strips of western hemlock (Tsuga heterophylla Sarg.) were used for the specimens. Two circular holes were cut along the axial centerline of the wider surface (longitudinal-tangential plane), and then two slots were cut from the holes asymmetrically to each other by varying the inclined angle of the slot with respect to the axial centerline. Shear stress was induced in the area between the holes, which is called the shear zone, by applying a tension load along the long axis of the specimen; the shear modulus, shear strength, and principal strain angle were measured from the shear stress/shear strain relation obtained. Independently of the in-plane shear tests, Iosipescu shear tests were conducted, and the validity of the in-plane shear tests was examined by comparing the test results with those obtained by the Iosipescu shear tests. In addition to the tests, stress distribution in the in-plane shear test was calculated by the finite element method, and the results were compared with those obtained by the actual in-plane shear tests. The following three results were obtained. First, the shear moduli obtained by the in-plane shear tests were close enough to those obtained by the Iosipescu shear tests throughout the range of inclined angle examined here. Additionally, the calculated result of the finite element method also verified the validity of the in-plane shear test for measuring the shear modulus. Thus, the in-plane shear test method examined was effective for measuring the shear modulus. Second, a failure was initiated at the hole edge because of the stress concentration, which was also confirmed by the finite element calculation, and it immediately propagated along the grain in the early stage of the test. Thus, it was difficult to obtain the proportional limit stress and realistic shear strength by the in-plane shear test because of the catastrophic failure in the early stage of the test. Third, since it is desirable that the stress field in the shear zone is close to the pure shear stress condition, we recommend that the slot runs outward from the hole when conducting the in-plane shear test in spite of the independence of the shear strength on the inclined angle.     

Accuracy of shear properties of wood obtained by simplified Iosipescu shear test

We examined the accuracy of the shear properties of wood by the Iosipescu shear test using specimens whose shape was simplified. Quartersawn boards of sitka spruce (Picea sitchensis Carr.) and shioji (Japanese ash,Fraxinus spaethiana Lingelsh.) were used. Two types of specimen for the Iosipescu shear test were compared: a standard specimen whose notch angle is 90° and a keyhole type specimen, which is more easily prepared than the standard type. The shear modulus, yield shear stress, and failure shear stress of the keyhole-type specimen were compared to those of the standard specimen. Shear stress analysis was conducted using the finite element method (FEM). The results obtained were as follows: (1) The failure pattern obtained by the simplified Iosipescu shear test was similar to that seen with the standard Iosipescu shear test. (2) The shear modulus, yield stress, and failure stress obtained by the simplified Iosipescu shear test coincided with those by the standard Iosipescu shear test. (3) The principal strain angle and principal stress angle of the simplified Iosipescu shear test were about 45°. (4) It is recognized that pure stress is applied to the strain-gauge regions in the simplified Iosipescu shear test, and it is expected that the shear properties are independent of the notch angle.     

Estimation of the shear strength of wood by uniaxial-tension tests of off-axis specimens

To determine shear strength we conducted uniaxial-tension tests of off-axis specimens and examined the proper off-axis angles. Sitka spruce (Picea sitchensis Carr.) and katsura (Cercidiphyllum japonicum Sieb. and Zucc.) were used for the studies. Uniaxial tension tests of the specimens with various off-axis angles were conducted, and the shear stress at failure was obtained. Independent of the tension tests, torsion tests were conducted, and the shear strengths were obtained. Comparing the data of the uniaxial tension and torsion tests, we examined the validity of estimating shear strength by the off-axis tension test. The shear strengths obtained from the tension tests coincided well with those measured by the torsion tests when the specimen had an off-axis angle of 15°–30°. In this off-axis angle range, the tensile stress perpendicular to the grain might have a serious influence on the shear strength, and we thought that the shear strength predicted by uniaxial tension tests should be treated as an approximate value despite the simplicity of the tension test. Other test methods should be adopted to obtain the precise shear strength of wood.     

Evaluation of a modified Iosipescu shear test method for determining the shear properties of clear wood

A modified Iosipescu shear test method is proposed as an alternative for measuring the shear properties of clear wood. The method adopts four-point asymmetric loading procedure in the Iosipescu shear test but with the loading positions shifted to the neutral axis of the specimen. The original V-notched specimen is replaced by a combination of polyvinyl chloride blocks at two ends and a bow-tie-shaped wood specimen in the middle to provide a better stress pattern at failure. The measured shear strength and shear moduli are compared with results from compression test and off-axis tension test. Finite element analysis is also carried out to study the stress distribution in the wood specimen. Results show that the new shear test setup can provide close-to pure shear stress state in the specimen yielding better estimates of the shear properties of wood. The shear strength obtained by the new test setup is slightly lower than that from the off-axis tensile test which is probably due to the relatively thick specimen chosen in this study.     

Estimation of shear moduli of wood by quasi-simple shear tests

A quasi-simple shear test, which is the most direct method for examining the shear properties of sheet metals, has been applied to measure the shear moduli of wood. Buna (Fagus crenata Blume) with variously sized shear regions was used for the test specimens. Strain gauges were mounted in the center of the shear regions to measure the shear strains. The shear tests were carried out to determine the shear moduli in the radial and tangential planes. Apparent shear moduli obtained from the experimental results were corrected by finite element method (FEM) simulation of the shear region, where both shearing and bending are produced. It was found that the corrected shear moduli are roughly independent of test conditions, and their values are in good agreement with the data obtained from bending-shear tests. This suggests that the method employed here can effectively estimate the shear moduli of wood.Part of this research was presented at the 50th Annual Meeting of the Society of Materials Science, Osaka, May 2001     

Measurement of the shear modulus of wood by static bending tests

When measuring the shear modulus of wood by static bending tests, the basic theory is dependent on Timoshenko's bending theory. The shear modulus obtained by static bending is a much smaller value than that derived by other methods. We examined the applicability of Timoshenko's theory and propose an empirical equation that can derive the shear modulus properly. Three softwoods and three hardwoods were used for the tests. First, the Young's modulus and shear modulus were measured by free-free flexural vibration tests. Then the three-point static bending tests were undertaken, varying the depth/span ratios. Additionally, the bending tests were simulated by the finite element method (FEM). The shear moduli obtained by these methods were then compared. The deflection behaviors in static bending were not expressed by the original Timoshenko bending theory because of the stress distortion near the loading point. Based on the experimental results and numerical calculations, we modified the original Timoshenko bending equation. When using our modified equation the stress concentration must be carefully taken into account.     

Shear strengths of wood measured by various short beam shear test methods

We conducted three types of short beam shear tests of western hemlock (Tsuga heterophylla Sarg.) under various span/depth ratios, and examined whether the maximum shear stress was used as the shear strength. The following results were obtained. (1) In the short beam shear tests under the three-point loading method, it was difficult to have the specimen failing by horizontal shear. We thought that this method should not be recommended for determining the shear strength of wood. (2) In the short beam shear tests under the asymmetric four-point loading of the specimen with a rectangular cross-section, the failure caused by horizontal shear occurred under some span/depth ratio range. Nevertheless, this range was dependent on the specimen geometry and was quite restricted. We therefore think that this method should not be recommended for determining the shear strength of wood. (3) In the short beam shear tests under the asymmetric four-point loading of the I-shaped specimen, failure caused by horizontal shear occurred under the span/depth ratio range wider than that applicable for the asymmetric four-point loading of the specimen with a rectangular cross-section. The maximum shear stress was stable in a certain span/depth ratio range and the value of the maximum shear stress is effective as a parameter for comparing the shearing strength of materials with each other.     

Bending and shear properties of compressed Sitka spruce

We examined the bending and shear properties of compressed wood using small and clear specimens of Sitka spruce (Picea sitchensis Carr.). For measuring the bending properties, three-point bending tests were conducted under the span/depth ratio of 14, which is standardized in the American Society for Testing and Materials [ASTM D143-94 (2005a)] and Japanese Industrial Standards [JIS Z2101-94 (1994)]. In the bending test, the load, deflection at the midspan, and strain at the bottom of the midspan were simultaneously measured, and Young’s modulus and bending strength were obtained by elementary beam theory. For obtaining the shear modulus and shear strength, asymmetric four-point bending tests were conducted using the specimens with rectangular and side-grooved cross sections, respectively, and the influence of the compression ratio on the shear properties was examined. The results are summarized as follows: (1) Young’s modulus increased with increasing compression ratio when it was determined by the load–strain relation. Nevertheless, this tendency was rather obscured when Young’s modulus was determined by the load–deflection relation. Hence, it is preferable that Young’s modulus is measured from the load–strain relation. (2) The shear modulus in the longitudinal–tangential plane was maximum at the compression ratio of 50%, whereas that in the longitudinal–radial plane was minimum at the compression ratio of 50%. (3) The influence of the compression on the bending and shear strength ratio was not significant.     

Measurement of the shear modulus of wood by asymmetric four-point bending tests

We conducted asymmetric four-point bending tests of wood and obtained the shear moduli on the basis of Timoshenko's theory of bending. Akamatsu (Japanese red pine,Pinus densiflora D. Don) and shioji (Japanese ash,Fraxinus spaethiana Lingelsh.) were used for the tests. Asymmetric four-point bending tests were undertaken by varying the depth/span ratios; and Young's modulus and the shear modulus were calculated by Timoshenko's bending theory. Independent of the asymmetric bending tests, we also conducted three-point bending tests, free-freeflexural vibration tests, and numerical calculations by the finite element method. Young's and shear moduli obtained by these methods were compared with those derived from the asymmetric bending tests. Based on these comparisons, we concluded that the shear modulus can be properly obtained by the asymmetric four-point bending tests when the span is 20 times larger than the depth.     

Simultaneous determination of shear strength and shear modulus in glued-laminated timber using a full-scale shear block specimen

A newly developed full-scale shear block specimen was used to simultaneously determine the shear strength and shear modulus of glued-laminated timber. The shear modulus was calculated using the shear strain distribution measured by means of digital image correlation. To obtain the exact relationship between shear modulus and shear strength, the shear strain in the intended shear plane was measured. A relatively high correlation coefficient of 0.75 was found between the shear modulus and nominal shear strength in two types of glued-laminated timber tested: sugi (Cryptomeria japonica) and Douglas-fir (Pseudotsuga menziesii). Good correlation was also found between the density of middle lamina and shear strength. However, the relationships to density showed species dependence, which was not observed in the relationship between shear modulus and shear strength.     

In-plane shear properties of the wood-based sandwich panel as a small shear wall evaluated by the shear test method using tie-rods

 The fundamental in-plane shear properties were investigated for the wood-based sandwich panel of plywood-overlaid low-density fiberboard (SW) manufactured at a pilot scale to develop it as a shear wall. The shear test method using tie-rods standardized for shear walls was applied to SW with dimensions of 260 mm square and 96 mm thick as a small shear wall and to plywood (PW) and thick low-density fiberboard (FB). The shear modulus and shear strength of PW, FB, and SW were determined. To measure the shear deformation angle, a displacement meter and strain-gauge were used. The shear moduli of PW (0.68 g/cm³) and FB (0.25–0.35 g/cm³) were 460 and 21–58 MPa/rad, respectively. The shear modulus of SW as a composite was analyzed. Some experimental models of SW were proposed (i.e., rigid-α, rigid-β, flexible, and semirigid models). The shear modulus of SW (0.35–0.40 g/cm³) evaluated based on the rigid-α and semirigid models were 73–89 and 109–125 MPa/rad, respectively. The theoretical shear modulus of SW was calculated to be 110–129 MPa/rad. Received: May 9, 2001 / Accepted: June 26, 2002 RID="*" ID="*" Part of this report was presented at the 50th Annual Meeting of the Japan Wood Research Society, Kyoto, Japan, April 2000; and the 5th Pacific Rim Bio-Based Composite Symposium, Canberra, Australia, December 2000 Acknowledgments The authors express our deep gratitude to Mr. Noritoshi Sawada (Hokushin Co.), Dr. Wong Cheng, and their cooperative members for their expert technical support for the preparation of manufacturing the thick fiberboard and sandwich panel. We are grateful also to Drs. Min Zhang, Kenji Umemura, Wong Ee Ding, and Guangping Han for their great help and advice in manufacturing the thick panels. The authors are grateful to Hokushin Co. for the fiber and resin and to Ishinomaki Gouhan Co. for the plywood. We thank Mr. Makoto Nakatani for his expert assistance when preparing the specimens for the shear test. Funding provided by the Research Fellowship of the Japan Society for the Promotion of Science for Young Scientists as a JSPS Research Fellow is also gratefully acknowledged.     

Measurement of bending properties of wood by compression bending tests

We measured Young's modulus, proportional limit stress, and bending strength by the compression bending test and examined the applicability of the testing method by comparing it with conventional bending test methods. Long columns of todomatsu (Japanese fir,Abies sachalinensis Fr. Schmidt) with various length/thickness ratios were the specimens. A compressive load was axially applied to the specimen supported with pin ends. Young's modulus, the proportional limit stress, and the bending strength were obtained from the load-loading point displacement and load-strains at the outer surfaces until the occurrence of bending failure. Four-point bending tests were also conducted, and the bending properties obtained were compared with the corresponding properties obtained by the compression bending tests. Based on the experimental results, we believe that when the stress-strain relation is measured by the load-loading point displacement relation using specimens whose length/thickness ratio is large enough, the bending properties can be obtained properly using the compression bending test.     

Derivation and application of an equation for calculating shear modulus of three-ply laminated material beam from shear moduli of individual laminae

In a detailed study of the relation between the deflection caused by shear force and the constitution of a laminated material beam, we derived an equation for calculating the shear modulus of a laminated material beam from the shear moduli of individual laminae. The validity of the derived equation was investigated using crosslaminated wood beams made with five species. The calculated shear moduli parallel to the grain of face laminae ranged from 48.3 MPa to 351 MPa, while those perpendicular to the grain of face laminae ranged from 58.0 MPa to 350 MPa. The calculated shear moduli increased markedly with increasing shear modulus in a cross section of perpendicular-direction lamina of a cross-laminated wood beam. The calculated apparent modulus of elasticity (MOE) of cross-laminated wood beams agreed fairly well with the measured apparent MOE values. This fact indicated that the apparent MOE of cross-laminated wood beam was able to be calculated from the true MOE values and shear moduli of individual laminae. The percentage of deflection caused by shear force obtained from the calculated apparent MOE (Y _sc) was close to that obtained from the measured apparent MOE (Y _s) and there was a high correlation between both values. From the above results, it was concluded that the derived equation had high validity in calculation of shear modulus of a cross-laminated wood beam.     

Shear tests of double shear plate connector joints in sugi—Japanese larch composite glulam beams

To study the shear strength of structural joints in sugi (Cryptomeria japonica D. Don) — Japanese larch (Larix kaempferi Carriere) composite glulam beams using structural connectors with double shear plates, shear tests were conducted on two types of joint (post-beam and girder-beam). Two types of the composite beam (240 and 300 mm depth) were prepared for the tests. Ordinary sugi glulam beam and Japanese larch glulam beam were also used as control specimens. The load—displacement curves of joints in composite beams were somewhere between those of sugi and Japanese larch glulam beams. The shear strength of joints in composite beams was higher than that in the sugi glulam beam control. However, the allowable loads of the joints in composite beams were lower than those in the sugi beam with 240 mm depth. Large variation of maximum load of the joints in the composite beams resulted in lower allowable load.     

Influence of loading point on the static bending test of wood

We conducted three-point bending tests by changing the condition at the loading point and then examined the influence of the loading point on the test data. Yellow poplar (Liriodendron tulipfera L.) was used for the tests. First, using loading noses with various radii, static bending tests were conducted by varying the depth/span ratios. Deflections were measured from the displacement of the cross head and at the point against the loading nose: Young's and shear moduli were obtained from the modified Timoshenko's bending equation proposed in a previous paper. Then a similar testing procedure was undertaken by inserting cushion sheets of Teflon between the specimen and the nose. After the measuring these moduli, bending strengths were measured using the loading noses and cushion sheets. The following results were obtained: (1) When the deflection was measured from the displacement of the cross head, the radius of the loading nose had an influence on the additional deflection when the depth/span ratio was high, causing the dependence of the shear modulus on the radius. In contrast, the radius had little influence on the measurement of Young's modulus. By placing cushion sheets between the nose and the specimen, the effect of the radius was moderated. When the deflection was measured at the point against the loading nose, the radius of the nose had little influence on the additional deflection; hence the loading nose had little influence when obtaining Young's and shear moduli. This tendency was commonly observed regardless of whether the cushion sheets were in place. (2) When the specimen had a high depth/span ratio, the bending strength increased with the increase in the radius of the loading nose. However, the influence of the radius was small when the specimen had a low depth/span ratio. There was no significant effect of the cushion sheets used here on the measurement of bending strength.Part of this paper was presented at the 48th annual meeting of the Japan Wood Research Society, Shizuoka, April 1998     

Effect of element type on the internal bond quality of wood-based panels determined by three methods

Three mechanical tests with different loading modes were conducted to evaluate the effect of element type on the internal bond quality of wood-based panels. In addition to the internal bond test, which is commonly used for mat-formed panels, interlaminar and edgewise shear tests were used to test oriented strandboard (OSB), particleboard, medium-density fiberboard (MDF) of two thicknesses, and plywood. The following results were obtained. Epoxy resin proved to be suitable for determining the interlaminar shear modulus instead of hot-melt glue. There was a linear relation between panel density and interlaminar shear modulus and a linear correlation between the interlaminar shear strength and internal bond (IB) strength for the mat-formed panels tested. OSB had the highest edgewise shear modulus, and MDFs had the highest edgewise shear strength in this study. The modulus/strength ratio also depended on both panel type and loading mode. The relation between the shear moduli determined from the edgewise and interlaminar tests indicated the characteristics of the shear properties of panels made of different elements.Part of this paper was presented at the Fourth International Wood Science Symposium, Serpong, Indonesia, September 2002     

Evaluation of embedding strength on Uruguayan wood to apply the European yield theory for double shear bolted joint

The main objective of this study was to evaluate embedding strength on Uruguayan wood to apply the European yield theory (EYT) for double shear bolted joints’ on Eucalyptus grandis H.(EGH). To introduce the dowel-type connection performance, double shear tests were conducted. The embedding tests were conducted to calculate the yield strength of bolted joint by EYT and the compression test, to estimate the embedding strength. The yield strength obtained from the experiments showed a good agreement with the yield strength calculated by EYT method. The yield strength of double shear bolted joint evaluated from compressive strengths is a very close to the yield strength calculated by EYT. The average value and variability of the yield strength of double shear bolted joint calculated by EYT applying the embedding strengths of experimental results were very close to the yield strength or 5 % offset method of experimental results. The results from this study showed a good behavior to structural design with EGH in accordance to the Japanese standard code.     

Estimation of shear strength of dowel-type timber connections with multiple slotted-in steel plates by European yield theory

The shear strength of dowel-type timber connections with multiple slotted-in steel plates was estimated based on European yield theory. The values calculated based on the yield theory were compared with experimentally obtained results. An experiment was performed on dowel-type timber connections with two and three slottedin steel plates under lateral loads parallel to the grain. The yield mode of the dowel-type connection assumed in this study corresponds approximately to the failure mode of the connection obtained from the experiment. The shear strength of the dowel-type connections calculated based on the yield theory showed good agreement with the results for shear strength obtained in the experiment. The yield theory was useful for estimating the shear strength of the doweltype connection with multiple slotted-in steel plates. The shear strength of the dowel-type connection was greatly affected by the spacing of the steel plates, the number of steel plates, and the timber thickness. The values of these parameters that showed the proper shear strength of the dowel-type connection could be estimated based on the yield theory. Part of this paper was presented at the 9th Timber Engineering Forum of the Japan Timber Engineering Society, December 2005     

Combined shear and compression analysis using the Iosipescu device: analytical and experimental studies of medium density fiberboard

The possibility of using the Iosipescu shear test device to study the combined shear and compression behavior of anisotropic materials was examined. Measurements were made using both an original (Wyoming version) and an in-house modified Iosipescu shear and compression fixture. Numerical simulation of the combined shear and compression test was carried out to verify the reliability of the modified device. The numerical results were compared with data from experiments on a medium-density fiberboard. The numerical results show good agreement with the experimental results for the shear test in all the three material directions tested. The shapes as well as the values of the strain fields were similar in the numerical and experimental results. Different rotations of the combined shear and compression device were studied using the finite element method to find the combinations that gave reliable results in shear and compression. It was found that the 45° rotation gave the most uniform strain fields in the section between the notches. This rotation was tested on the fiberboard.     

Surface quality sensing of trembling aspen (Populus tremuloides Michx.) veneer products by near infrared spectroscopy

Abstract

The potential of near infrared spectroscopy (NIRS) to estimate wood moisture content (MC), surface energy characteristics and adhesive bond strength were evaluated on aspen (Populus tremuloides Michx.) veneer subjected to different drying times. For samples dried progressively at 103°C, the best MC prediction model was for the total MC range (0–100%) with an R² value of 0.68. However, exposure at 180°C produced surface colour changes, and the CIE L*a*b* colour parameters measuring colour changes were better estimated using the 400–900 nm spectral data than the 1100–2400 nm spectral data. Increased exposure time at 180°C resulted in lower wettability and, hence, larger contact angles, especially when ethylene glycol was used as probe solvent. Lap shear strength tests on veneers showed that adhesion by phenol formaldehyde resins was impaired by the high temperature exposure; however, the lap shear strength test had high variability so there was not always a clear relationship between contact angle and lap shear strength test.