Starch and By‐Products from a Laboratory‐Scale Barley Starch Isolation Procedure

Starch was isolated from three different barleys with normal, highamylose, or high‐amylopectin (waxy) starch. The laboratory‐scale starch isolation procedure included crushing of grains, steeping, wet milling, and sequential filtration and washing with water and alkali, respectively. Yield and content of starch, protein, and dietary fiber, including β‐glucan, were analyzed in isolated starch and in the by‐products obtained. Starch yield was 25–34%, and this fraction contained 96% starch, 0.2–0.3% protein, and 0.1% ash. Most of the remaining starch was found in the coarse material removed by filtration after wet milling, especially for the high‐amylose barley, and in the starch tailings. Microscopy studies showed that isolated starch contained mostly A‐granules and the starch tailings contained mostly B‐granules. Protein concentration was highest in the alkali‐soluble fraction (54%), whereas dietary fiber concentration was highest in the material removed by filtration after alkali treatment for the normal and waxy barleys (55%). The β‐glucan content was especially high for the waxy barley in this fraction (26%). The study thus showed that it was possible to enrich chemical constituents in the by‐products but that there were large differences between barleys. This result indicates a need for modifications in the isolation procedures for different barleys to obtain high yields of starch and different by‐products. Valuable by‐products enriched in β‐glucan or protein, for example, may render starch production more profitable.     

Effects of Pearling,Grinding Conditions,and Roller Mill Flow on the Yield and Composition of Milled Products from Hull‐less Barley

Two hull‐less barley cultivars, one with waxy starch and the other with high‐amylose starch, were roller‐milled unpearled and after 15% pearling. Flows of varying length, with diverse roll settings and roll surfaces were used to determine effects on the yield, composition, and properties of milled products. Similar trends were noted for the two cultivars. When using a short flow comprising four break passages and a sizing passage, power consumption during grinding was reduced by 10% when roll flute orientation was changed from dull‐to‐dull (D/D) to sharp‐to‐sharp (S/S). Flute orientation had minimal effects on the yield and brightness of flour, but SS grinding gave a higher yield of a fiber‐rich fraction (FRF). FRF yield and composition are of particular interest because FRF has potential as a functional food ingredient due to elevated levels of β‐glucans (BG) and arabinoxylans (AX). When using smooth frosted rolls (SM) for the sizing passage, power consumption increased by several times over using fluted sizing rolls with little advantage for either yield or BG content of FRF. FRF starch damage increased when smooth sizing rolls were used, and water swelling, a measure of water hydration capacity, also increased. Setting break and sizing rolls sharp‐to‐sharp significantly lowered the mean particle size of the FRF fraction, accompanied by moderate declines in FRF BG and AX contents. FRF yield decreased ≤50% when milling flow was lengthened to three sizing passages with intermediate impact passages, with only a moderate accompanying increase in FRF fiber content, regardless of roll conditions. Pearling 15% before milling reduced the yield of FRF by ≈30% while moderately reducing flour yield. Flour brightness was improved by pearling. When barley was pearled, FRF contained higher amounts of BG, but lower amounts of AX, phenolics, ash, and protein.     

Distribution of β‐Glucan in the Grain of Hull‐less Barley

Nine hull‐less barley (HB) containing waxy (0–7% amylose), normal (≈25% amylose), or high amylose (≈42% amylose) starch with normal or fractured granule make‐up and 4–9% (1→3)(1→4)‐β‐d ‐glucans (β‐glucan) were pearled to remove 70% of the original grain weight in 10% intervals. The pearled fractions were analyzed for β‐glucan distribution within HB grain. Protein content of the pearled fractions indicated that the three outermost fractions contained pericarp and testa, aleurone, and subaleurone tissues, respectively. For all HB, β‐glucan and acid‐extract viscosity were very low in the outermost 20% of the kernel. For low β‐glucan HB, β‐glucan content was the greatest in the subaleurone region and declined slightly toward inner layers. For high β‐glucan HB, however, more than 80% of grain β‐glucan was distributed more evenly throughout the endosperm. Acid extract viscosity was significantly (P < 0.01) correlated with total (r = 0.75) and soluble (r = 0.87) β‐glucan content throughout the kernel of all HB. Growing conditions, location and year, had significant effects on the concentration of protein, starch and β‐glucan. However, protein, starch, and β‐glucan distribution patterns were not affected by growing conditions. The difference in β‐glucan distribution between low and high β‐glucan HB may explain the difference in milling performance of HB with low or high β‐glucan.     

Laboratory Procedure to Wet‐Mill 100 g of Grain Sorghum into Six Fractions

A small‐scale (100 g of grain) procedure was developed to wet‐mill grain sorghum into six fractions by modifying the procedure of Eckhoff et al (1996). The wet‐milling process was repeated five times on commercial grain sorghum, and the mean yield (69.4%) of starch (≤0.3% protein) varied by 0.3%, whereas the yields of fiber, gluten, and germ plus bran fractions varied by 5–6%. The starch fraction accounted for ≈95% of that in the grain, while the total solids recovered was 99.0%. Four other samples of grain sorghum gave 92–95% recoveries of starches and 98.2–99.8% recoveries of total solids. All grain sorghum starches had lightness (L*) values and pasting curves nearly equal to those of a commercial maize starch.     

Recovery and Purity of Isolated Barley Starch and Protein as Affected by Fractionation Water Temperature

Wet fractionation of barley flours was conducted to identify appropriate fractionation water temperature considering the recovery and purity of starch and protein. In abraded hulless regular barley, yield of starch fraction, starch recovery, and purity of the protein fraction increased from 43.3 to 45.7%, from 61.7 to 64.8%, and from 37.6 to 65.2% when water temperature in fractionation was increased from 23 to 60°C. In abraded hulless waxy barley, recovery of starch with 40°C water was much greater (67.7%) than that at other temperatures (<61.7%). Starch recovery and protein purity of regular barley cultivars were higher than those of waxy barley cultivars with fractionation water of 60°C. In whole hulless barley flours fractionated with 60°C water, waxy barley flours showed similar to or higher protein purity (44.8–48.9%) than regular barley flours (42.8– 44.6%), while regular barley flours exhibited higher starch recovery (>60.6%) than waxy barley flours (<57.3%). The purity of isolated starch was >97.7%, regardless of water temperature and barley type. Considering yield and recovery of the isolated starch, and purity of the isolated protein, 60°C water for hulless regular barley and 40°C for hulless waxy barley seem to be appropriate for fractionation of barley flour for isolation of starch and protein.     

Wet‐Milling Characteristics of 10 Lines from Germplasm Enhancement of Maize Project Compared with Five Corn Belt Lines

The use of corn (Zea mays L.) hybrids with high grain yield and starch extractability has steadily increased in the processing industry. In light of widespread corn seed industry participation in the Germplasm Enhancement of Maize Project (GEM), which seeks to enhance exotic germplasm, future hybrids may contain more exotic sources in genetic backgrounds. It is necessary to establish and monitor physical, compositional, and milling characteristics of the new exotic breeding materials to determine the processing value. The present study was conducted to determine the wet‐milling characteristics of a set of GEM lines compared with typical Corn Belt lines. Ten GEM lines introgressed with exotic materials from Argentina, Chile, Cuba, Florida, and Uruguay and previously identified as having different starch yields, three commercial inbred lines, and two public inbred lines (B73 and Mo17) were analyzed using both near‐infrared transmittance (NIT) and a 100‐g wet‐milling procedure. There were statistical differences (P < 0.05) in the yield of wet‐milled fractions (starch, fiber, gluten, and germ). The GEM lines AR16035:S19‐227‐1‐B and CUBA117:S1520‐562‐1‐B had similar or better starch yield and starch recovery than B73 and the other adapted inbred lines, indicating that they may be useful in improving the proportion of extractable starch present in kernels of hybrids. Residual protein levels in the starch and gluten fractions were 0.26–0.32% and 38–45%, respectively. The starch yield of GEM lines from wet milling correlated positively with starch content from NIT and was negatively correlated with protein content of the corn kernels. Oil content in the germ varied from 50 to 60%. Our results indicate that incorporating GEM lines in a breeding program can maintain or even improve wet‐milling characteristics of Corn Belt materials if lines with appropriate traits are used.     

Chemical Composition of Barley Cultivars Fractionated by Weighing,Pneumatic Classification,Sieving, and Sorting on a Specific Gravity Table

Five different barley cultivars, including covered and naked samples containing low, normal, or high-amylose starches were fractionated by weighing, pneumatic classification, sieving, or sorting on a specific gravity table, and analyzed for content of starch, protein, ash, and β-glucan. For ash content, almost no variation could be found between different fractions. Protein content was minimum in the intermediate fractions for all cultivars when sorted by weighing. For the other fractionation methods, the differences in protein content were small. A tendency for decreasing content of starch with increasing grain mass and size could be seen when fractionating grains by weighing and sieving, respectively. The clearest trend was seen in differences in β-glucan content for all cultivars and all methods used. The main interpretation of our results is, however, that the chemical composition within the cultivars studied is very similar for all fractions, and that the differences between the unfractionated barley samples are larger.     

Roller Milling of Canadian Hull‐less Barley: Optimization of Roller Milling Conditions and Composition of Mill Streams

Roller milling of hull‐less barley generates mill streams with highly variable β‐glucan and arabinoxylan (AX) content. For high β‐glucan cultivars, yields >20% (whole barley basis) of a fiber‐rich fraction (FRF) with β‐glucan contents >15% can be readily obtained with a simple short mill flow. Hull‐less barley cultivars with high β‐glucan content require higher power consumption during roller milling than normal β‐glucan barley. Recovery of flour from high β‐glucan cultivars was greatly expedited by impact passages after grinding, particularly after reduction roll passages. Pearling before roller milling reduces flour yield and FRF yield on a whole unpearled barley basis, but flour brightness is improved and concentration of β‐glucan in fiber‐rich fractions increases. Pearling by‐products are rich in AX. Pearling to 15–20% is the best compromise between flour and FRF yield and flour brightness and pearling by‐products AX content. Increasing conditioning moisture from 12.5 to 14.5% strongly improved flour brightness with only a moderate loss of flour yield on a whole unpearled barley basis. As moisture content was increased to 16.5%, flour yield declined without a compensating improvement in brightness, but the yield of fiber‐rich fraction continued to increase and concentration of β‐glucan in FRF also increased.     

Quality of Flours from Waxy and Nonwaxy Barley for Production of Baked Products

One nonwaxy (covered) and two waxy (hull-less) barleys, whole grain and commercially abraded, were milled to break flour, reduction flour, and the bran fraction with a roller mill under optimized conditions. The flour yield range was 55.3–61.8% in whole grain and increased by 9–11% by abrasion before milling. Break flours contained the highest starch content (≤85.8%) independent of type of barley and abrasion level. Reduction flours contained less starch, but more protein, ash, free lipids, and total β-glucans than break flours. The bran fraction contained the highest content of ash, free lipids, protein, and total β-glucans but the lowest content of starch. Break flours milled from whole grain contained 82–91% particles <106 μm, and reduction flours contained ≈80% particles <106 μm. Abrasion significantly increased the amount of particles <38 μm in break and reduction flours in both types of barley. Viscosity of hot paste prepared with barley flour or bran at 8% concentration was strongly affected by barley type and abrasion level. In cv. Waxbar, the viscosity in bran fractions increased from 428 to 1,770 BU, and in break flours viscosity increased from 408 to 725 BU due to abrasion. Sugar snap cookies made from nonwaxy barley had larger diameter than cookies prepared from waxy barley. Cookies made from break flours were larger than those made from reduction flours, independent of type of barley. Quick bread baked from nonwaxy barley had a loaf volume similar to that of wheat bread, whereas waxy barley bread had a smaller loaf volume. Replacement of 20% of wheat flour by both waxy and nonwaxy barley flour or bran did not significantly affect the loaf volume but did decrease the hardness of quick bread crumb.     

Physical,Compositional, and Wet‐Milling Characteristics of Mexican Blue Maize (Zea mays L.) Landrace

Mexico has the largest diversity of genetic resources for maize in the world, with about 59 different landraces. However, little is known about their wet‐milling characteristics. The aim of this study was to determine whether 15 Mexican blue maize (Zea mays L.) genotypes of Elotero de Sinaloa landrace collected in the northwestern region of Mexico have suitable wet‐milling properties. Great variability of physical, compositional, and wet‐milling characteristics among these blue maize genotypes was observed. The FAUAS‐457 and FAUAS‐488 maize genotypes had similar starch yield and starch recovery as reported for the wet‐milling industry, which indicated that they may be useful as a source of extractable starch. Residual protein levels in the starch fractions were in the range of 0.39–0.68%, and total solids recovery exhibited a mean value of 98.8%, indicating acceptable efficacy of the wet‐milling process. This process afforded starches from blue maize genotypes with low protein contents. Wet‐milling fractions correlated with the physical and chemical properties of the kernels. Our results indicate that Mexican blue maize genotypes contain characteristics that make them appropriate and utilizable at the industrial level, and they can also be valuable for improving wet‐milling characteristics of maize through breeding programs.     

Distribution and Structural Variation of Nonstarch Polysaccharides in Milling Fractions of Hull‐less Barley with Variable Amylose Content

Three hull‐less barley genotypes containing starches with variable amylose content (23.8% normal, 4.3% waxy, 41.8% high‐amylose barley) were pearled to 10% and then roller‐milled to produce pearling by‐products (PBP), flour, and fiber‐rich fractions (FRF). PBP were enriched in arabinoxylans, protein, and ash and contained small amounts of starch and β‐glucans. FRF were considerably enriched in β‐glucans and arabinoxylans. The solubility of β‐glucans was higher in PBP than in FRF. The solubility of arabinoxylans was higher in FRF than in PBP. Small amounts of arabinogalactans detected in barley were concentrated in the outer portion of the barley kernel. The content and solubility of nonstarch polysaccharides (NSP) in various milling fractions was also dependent on the type of barley. To obtain more detailed information about the content and molecular structure of NSP, each milling fraction was sequentially extracted with water, alkaline [Ba(OH)₂], again with water, and finally with NaOH. These extractions resulted in four sub‐fractions: WE, Ba(OH)₂, Ba(OH)₂/H₂O, and NaOH. β‐Glucans and arabinoxylans exhibited structural heterogeneity derived from differences in their location within the kernel as well as from the genetic origin of barley. The WE arabinoxylans from FRF and flour had a substantially lower degree of branching than those from PBP. The WE arabinoxylans from FRF of high‐amylose and normal barley contained more unsubstituted Xylp residues but fewer doubly‐substituted and singly‐substituted Xylp at O‐2 than their counterparts from PBP. The WE arabinoxylans from FRF of waxy barley had a relatively high content of doubly‐substituted, but very few singly‐substituted Xylp residues. In all three barley genotypes, the ratio of tri‐ to tetrasaccharides in β‐glucans from PBP was higher than from flour and FRF. Substantial differences in the molecular weight of NSP in different milling fractions were also observed.     

Functionality of Barley Proteins Extracted and Fractionated by Alkaline and Alcohol Methods

This research optimized the extraction of different protein fractions from barley grains and assessed the physicochemical properties of the fractions obtained. Pearling was first used to remove the grain's outer layers (mainly bran and germ) so that the barley cytoplasmic proteins (albumin and globulin) would be enriched in the pearling flour (PF), while endosperm proteins (hordein and glutelin) would be enriched in the pearled grain flour (PGF). Salt, alcohol, and alkaline solutions were then used to extract different barley protein fractions from PF and PGF. The effects of extraction solvent type, pH, temperature, and extraction time on protein content and extraction efficiency were studied. Aqueous ethanol (55%, v/v) efficiently extracted barley hordein from PGF at 60°C, whereas pH 11.5 alkaline solution was the most efficient for extracting both cytoplasmic and endosperm proteins from barley PF and PGF at 23°C. Subunit molecular weight, amino acid composition, and the functional properties of each isolated barley protein fraction were investigated. Barley glutelin demonstrated superior oil‐binding property and emulsifying stability, whereas barley hordein exhibited good foaming capacity.     

Physicochemical and Digestion Characteristics of Starch and Fiber‐Rich Subfractions from Four Pulse Bagasses

The aim of this study was to characterize the physicochemical, functional, and digestion properties of bagasses derived from broad beans, chickpeas, lentils, and white beans, and to isolate the starch and a fiber‐rich fraction that can be used as a food ingredient. The bagasses showed different chemical compositions that were related to their botanical origin. The further processing that involved mechanical separation of starch yielded up to 69.65% with ≥80.12% recovery and high purity (≥94.42%), and a fiber‐rich fraction (total dietary fiber content ≥72.75%) in which the majority was insoluble fiber. The starch digestion fractions of the isolated lentil starch showed the highest amount of slowly digestible starch (30.76%), whereas the white bean contained the highest resistant starch content (15.65%). All starches showed predicted glycemic indexes ≤ 66.90, which classify them as medium glycemic foods. In vitro protein digestion was higher for the bagasse fraction (up to 89.78%), followed by the fiber‐rich fraction (84.36%). This research demonstrates that it is possible to revalorize the use of pulses bagasse, which could contribute to enhance the technological and economic output of the protein isolation process, rendering two potentially functional fractions.     

Starch Lipids of Barley and Malt

Barley and malt starches were compared with respect to their lipid content and composition. The starch lipids were first fractionated into internal and surface lipid fractions followed by lipid class and fatty acid analyses of each fraction. Barley starch contained 13 mg/g lipids, of which 9.3 mg were internal lipids and 3.7 mg were surface lipids. The total lipid content of malt starches varied between 11 and 13 mg/g of starch. However, malt starch contained only 1 mg of surface lipids; therefore, the internal lipid contents were as high as or even higher than those in the corresponding fraction of barley starch. Lipid class analyses suggested that the ability for hydrolysis of starch surface lipids was increased in malt. The hydrolysis occurred during the malting or the isolation process, resulting in reduced surface lipid content in malt starch. However, no reduction in the portion of polyunsaturated fatty acids was seen; therefore, lipid oxidation could not have been responsible for the lower content of malt starch surface lipids. Also, not only was the content of starch internal lipids higher in malt, but the composition of these lipids was different when compared to barley starch. The increase in starch internal lipids during malting may be due to transportation and reacylation of free fatty acids that had been liberated by hydrolysis from surface lipids.     

Einfluß variierter Mg-Ernährung auf Tausendkorngewicht und P-Fraktionen des Gerstenkorns

Influence of varying Mg supply to barley on thousand grain weight and the P fractions of grains By variation of the Mg concentration in the nutrient solution (0.2; 0.6 and 1.8 me Mg/l respectively) during tillering, shooting and grain filling it could be shown, that increasing Mg supply to barley especially favours number of ears/plant (tillering) and grain size (thousand grain weight, TGW). A positive correlation was found between Mg content of grain and TGW. In small grains, which had a Mg content of 0.06% Mg in DM, about 64% of grain-P was present as Phytin-P and 20% as inorganic P. In bigger grains being also higher in Mg content, however, 70% was Phytin-P and only 10% P_i. This change in the pattern of P-fractions due to the Mg nutrition might be of a certain relevance to the regulation of starch synthesis within the grain and accordingly of grain growth.     

Isolation and Characterization of High‐Purity Starch Isolates from Regular,Waxy, and High‐Amylose Hulless Barley Grains

Recovering starch from barley is problematic typically due to interference from β‐glucan (the soluble fiber component), which becomes highly viscous in aqueous solution. Dry fractionation techniques tend to be inefficient and often result in low yields. Recently, a protocol was developed in our laboratory for recovering β‐glucan from barley in which sieving whole barley flour in a semiaqueous (50% ethanol) medium allowed separation of the starch and fiber fractions without activating the viscosity of the β‐glucan. In this report, we investigate an aqueous method which further purifies the crude starch component recovered from this process. Six hulless barley (HB) cultivars representing two each of waxy, regular, and high‐amylose cultivars were fractionated into primarily starch, fiber, and protein components. Starch isolates primarily had large granules with high purity (>98%) and yield range was 22–39% (flour dry weight basis). More importantly, the β‐glucan extraction efficiency was 77–90%, meaning that it was well separated from the starch component during processing. Physicochemical evaluation of the starch isolates, which were mainly composed of large granules, showed properties that are typical of the barley genotypes.     

Effects of split nitrogen fertilization on post-anthesis photoassimilates,nitrogen use efficiency and grain yield in malting barley

Abstract

Split nitrogen applications are widely adopted to improve grain yield and enhance nitrogen use effective in crops. In a two-year field experiment at two eco-sites, five fractions of topdressed nitrogen of 0%, 20%, 30%, 40% and 50% were implemented. Responses of radiation interception and leaf photosynthesis after anthesis, dry matter accumulation and assimilates remobilization, nitrogen use efficiency and grain yield to fraction of topdressed nitrogen treatments were investigated in malting barley. Net photosynthetic rate of the penultimate leaf, leaf area index and light extinction coefficient increased with increasing fraction topdressed nitrogen from 0% to 30%, and then decreased from 30% to 50%. The putative gross maximum canopy photosynthesis was the highest for fraction of topdressed nitrogen of 30%, which was concomitant with the highest amount of post-anthesis accumulated assimilates. The remobilization of pre-anthesis stored assimilates from vegetative organs into grains was hardly significantly affected by fractions of topdressed nitrogen. Grain yield was the highest for fraction of topdressed nitrogen of 30%, which coincided with the highest plant nitrogen uptake and physiological and agronomic nitrogen use efficiencies. The enhanced nitrogen use efficiency was corresponding to the improved photosynthetic nitrogen-use efficiency in the leaves at fraction of topdressed nitrogen of 30%. In conclusion, appropriate fraction of topdressed nitrogen application on malting barley improved assimilation rate and nitrogen use efficiency resulting in higher grain yields and proper grain protein content in malting barley.     

Nutrient Content in Buckwheat Milling Fractions

Buckwheat seeds (Fagopyrum esculentum Moench) were milled into 23 fractions: seven fine flours, three coarse flours, four small semolina, two big semolina, six bran, and one husk fraction. A considerable variation in gross chemical composition was found among the milling fractions. The protein content varied from 4.4 to 11.9% (db) in flours and from 19.2 to 31.3% in bran fractions; starch varied from 91.7 to 70.4% in flours and from 42.6 to 20.3 in bran. The percentage of soluble dietary fiber contained in total dietary fiber was higher in flours than in semolina and bran fractions. Ash, Fe, P, tannin, phytate content, and color were also investigated. A unique distribution of phytate was found in starch. Correlation is significantly positive in husk, bran, and semolina fractions, while correlation is significantly negative in flour fractions. Depending on technological or nutritional demands, appropriate fractions may be chosen to achieve the desired end‐use product.     

Study of a Small‐Scale Laboratory Wet‐Milling Procedure for Wheat

The objectives of this research were to study the effects of slurry specific gravity, starch table slope, slurry pumping rate, and their interactions on starch recovery and purity; and to propose a small‐scale laboratory wet‐milling procedure for wheat. First‐order and second‐order response surface regression models were developed to study the effects and interactions of slurry specific gravity, starch table slope, and slurry pumping rate on starch and gluten separation for a 100‐g wheat wet‐milling procedure. The starch and starch protein content data fit the first‐order models (R² = 0.99 and 0.96) better than the second‐order models (R² = 0.98 and 0.93). Regression results from the first‐order models indicated that specific gravity, table slope, pumping rate, and their interactions all had a significant effect on starch yield and purity. However, these effects could be simplified as the effect of the resident time of starch and gluten slurry on the starch table and the specific gravity. Starch yield increased as resident time increased and specific gravity decreased. Protein content in starch decreased as the resident time decreased and the specific gravity increased. The separation condition with specific gravity of 3 Bé, table slope of 1.04 cm/m, and pumping rate of 50 mL/min was recommended. Under this condition, starch recovery was 85.6% and protein content of starch was 0.42%, which was similar to the 1.5‐kg laboratory methods in starch recovery. Total solids recovery was 98.1%, which is similar to that from 1.5‐kg laboratory methods. These results indicated that precision of the 100‐g wheat wet‐milling procedure was similar to that of the 1.5‐kg laboratory methods.     

Effect of Heat Treatments on Microbial Load and Associated Changes to β‐Glucan Physicochemical Properties in Whole Grain Barley

Health claims for barley β‐glucan (BG) have prompted the development of food products containing barley; however, some new products (such as milled grain used without a cook step, as in a smoothie) do not use any form of heat treatment during processing or prior to consumption, which could affect microbial safety and potential health benefits. The aims of this research were to evaluate current commercial barley products for microbial counts and BG characteristics and to determine the effects of different heat treatments on these attributes in whole grain barley samples. Three heat treatments (micronization, roasting, and conditioning) were performed on three cultivars of barley (CDC Rattan, CDC McGwire, and CDC Fibar). The microbial quality was measured with standard plate count (SPC), mold and yeast count (MYC), and coliforms or Escherichia coli . Only four of the 17 commercial barley products tested met acceptable microbial limits used in this study. All three heat treatments applied to the barley samples in this study reduced SPC, MYC, and coliforms to an acceptable level. BG was extracted with an in vitro digestion method to determine its viscosity, molecular weight (MW), and solubility. All three heat treatments produced BG extracts with high viscosity and MW compared with untreated barley. Overall, heat treatments improved both the safety and the potential health benefits from soluble BG in whole grain barley.