Predicting the saturated hydraulic conductivity of compacted subsoils using the non-similar media concept

It is widely recognized that saturated hydraulic conductivity is dominated by the micromorphology of soil pores rather than by the merely total porosity or dry bulk density. Nevertheless, some researchers are reporting that the decrease in saturated hydraulic conductivity of subsoil is simply associated with the decrease in soil porosity or increase in dry bulk density. Based on these understandings in published papers and on our preliminary field investigation, we assumed that micromorphology of soil pores in topsoils is subjected to be destroyed with continuous disturbance by frequent tillage while subsoils tend to be compacted without serious changes of micromorphology of soil pores. Thus, we focused on finding the dependence of saturated hydraulic conductivity on dry bulk density by separating the soils into tilled layer and compacted layer. The objective of this study was to describe the relationship between saturated hydraulic conductivity and dry bulk density using a theoretical model, the non-similar media concept (NSMC) model, capable of predicting saturated hydraulic conductivities of soils with different values of dry bulk densities. The study area was located near the Tone River in Saitama Prefecture, Japan, where the soils were classified into Haplic Brown Lowland Soils according to the Classification of Cultivated Soils in Japan (Eutric Fluvisol according to FAO/UNESCO). Two sites, where the topsoils were seasonally tilled while the subsoils were sustained as it is, and another site where the topsoil was seasonally tilled, too, but extra deep tillage (1 m tillage depth) had been done, were chosen for the measurements. The saturated hydraulic conductivities and dry bulk densities of undisturbed soil cores from different depths were measured in the laboratory. The NSMC model was carefully applied only when the soil textures were the same among samples. The well-known conventional equations formulated by Kozeny–Carman and by Campbell, were used to compare the applicabilities with the NSMC model. The NSMC model succeeded in predicting the saturated hydraulic conductivities in the compacted subsoils. On the other hand, the NSMC model was not applicable to the tilled topsoils and to the deeply tilled subsoil. The saturated hydraulic conductivity of tilled topsoils and deeply tilled subsoil was always lower than that of compacted subsoils at the same dry bulk densities. The Kozeny–Carman and Campbell equations both failed in the prediction of saturated hydraulic conductivity in subsoil. It was concluded that the saturated hydraulic conductivity of subsoils under compaction without extreme disturbance is well related with its dry bulk density by the NSMC model.     

Structure and hydraulic properties of the boreal clay soil under differently managed buffer zones

Vegetated buffer zones (BZs) between arable fields and bodies of water are commonly established to reduce erosion and run‐off of particle‐bound nutrients. Functioning of a BZ depends on soil structure, as it is important for water infiltration. Therefore, it is vital to understand how varying management practices affect soils of BZs. We studied the structural and hydraulic properties of three differently managed BZs established in a boreal Vertic Stagnic Cambisol (clay, 51%). The three management practices for vegetation were as follows: natural with no treatment, harvested yearly and grazed by cattle. We used bulk density and macroporosity, together with a pore geometry index (air permeability per unit air‐filled porosity), to describe the soil structural properties. Hydraulic properties were measured at different length scales by means of an aggregate sorptivity test, saturated hydraulic conductivity of the core samples and field‐saturated hydraulic conductivity. Vegetation management markedly affected the physical properties in the top 5 cm of the soil. Properties were least favourable for infiltration at the grazed site, with the greatest bulk density, least macroporosity and hydraulic conductivity or greatest pore tortuosity. In general, spatial variation in zones with restricted and good hydraulic conductivity together with reduced aggregate sorptivity in the deeper horizons made the soil prone to preferential flow when initially dry. Prolonged wetness, on the other hand, reduced saturated hydraulic conductivity significantly, resulting in surface run‐off. Harvesting was considered the best management practice due to its inherent capacity for reducing the soil nutrient content and because it has minor implications for soil physical properties.     

Temporal changes of soil physical quality under two residue management systems

Although crop residue management is known to affect near‐surface soil physical quality, little is known about the temporal variability of these indicators over short time intervals. This study evaluates the temporal changes of nine indicators of soil physical quality. These are organic carbon content, structural stability index, bulk density, macroporosity, air capacity, relative field capacity, plant available water capacity, Dexter's S‐index and saturated hydraulic conductivity. A second set of soil physical indicators, based on the distribution of soil pore volume, was also evaluated. The indicators were determined in three different times during the growing cycle of winter durum wheat cultivated within a long‐term field research carrying out in Southern Italy and comparing two types of crop residue management, that is, burning (B) and soil incorporation (I). Only the bulk density changed over time for both treatments, although the air capacity also changed for the incorporation of wheat residues. Residual effects of the autumnal soil tillage and soil compaction were a common source of variability, irrespective of which treatment was used. Based on the existing guidelines for evaluating the physical quality of these agricultural soils, optimal or near‐optimal values were detected in about half of the cases under consideration. This suggests that both B and I create sufficiently good conditions for crop growth during the crop cycle. The comparison between observed and optimal soil pore distribution function was always poor. The pore volume distributions showed lower densities of small pores and relatively higher densities of large pores than the proposed optimal distribution. This study also suggests that the considered optimal or references curves probably cannot be applied successfully to a wide range of agricultural soils.     

Anisotropy of pore functions in structured Stagnic Luvisols in the Weichselian moraine region in N Germany

In order to determine if soil hydraulic properties present a direction‐dependent behavior, undisturbed samples were collected at different horizons and orientations (vertical, diagonal [45°], and horizontal) in structured soils in the Weichselian moraine region in northern Germany. The water‐retention curve (WRC), the saturated hydraulic conductivity (k_f), and the air permeability (k_a) were measured. The air‐filled porosity (?_a) was determined, and pore‐continuity indices (k_a/?_a, k_a/?_a², N) and blocked porosities (?_b) were derived from the relationship between k_a and ?_a. The development of soil structures with defined forms and dimensions (e.g., platy by soil compaction or prismatic up to subangular‐blocky by swelling–shrinkage processes) and the presence of biopores can induce a direction‐dependent behavior of pore functions. Although the pore volume as a scalar is isotropic, the saturated hydraulic conductivity and air permeability (as a function of air‐filled porosity) can be anisotropic. This behavior was observed in pore‐continuity indices showing that the identification of soil structure can be used as a first parameter to estimate if hydraulic properties present a direction‐dependent behavior at the scale of the soil horizon.     

Soil physical properties of afforested and arable land

Abstract. The effects of tree crops on the soil physical properties of former agricultural land were compared with those of ley in a rotation with cereals on adjacent sites. Five sites in southern Sweden were investigated focussing on soil water retention characteristics, dry bulk density, macroporosity and saturated hydraulic conductivity. Three of the sites were on light textured soils and two on clay soils. The tree crops were 30 to 35-year-old hybrid aspen, Populus deltoides , and silver birch, Betula pendula , and the ley crops were one to five years old.
The light-textured soils under tree crops showed bimodal pore size distributions in the macropore region, whereas under ley crops they showed unimodal distributions. Dry bulk densities were generally smaller and the macroporosities larger under tree crops compared with leyicereal crops. Saturated hydraulic conductivities tended to be larger under tree crops. Slopes of the linear regression lines between saturated hydraulic conductivity and each of the parameters dry bulk density, porosity and macroporosity were steeper in the soil under agricultural crops than under tree crops.
Observed differences in physical properties were considered to be an effect of land use, which had brought about changes in aggregate stability, pore size distribution and pore continuity.     

Vulnerability of Bavarian silty loam soil to compaction under heavy wheel traffic: impacts of tillage method and soil water content

Soil compaction caused by traffic of heavy vehicles and machinery has become a problem of world-wide concern. The aims of this study were to evaluate and compare the changes in bulk density, soil strength, porosity, saturated hydraulic conductivity and air permeability during sugar beet (Beta vulgaris L.) harvesting on a typical Bavarian soil (Regosol) as well as to assess the most appropriate variable factors that fit with the effective controlling of subsequent compaction. The field experiments, measurements and laboratory testing were carried out in Freising, Germany. Two tillage systems (conventional plough tillage and reduced chisel tillage) were used in the experiments. The soil water contents were adjusted to 0.17 g g⁻¹ (w₁), 0.27 g g⁻¹ (w₂) and 0.35 g g⁻¹ (w₃).Taking the increase in bulk density, the decrease in air permeability and reduction of wide coarse pore size porosity (−6 kPa) into account, it seems that CT (ploughing to a depth of 0.25 m followed by two passes of rotary harrow to a depth 0.05 m) of plots were compacted to a depth of at least 0.25 m and at most 0.40 m in high soil water (w₃) conditions. The trends were similar for “CT w₁” (low soil water content) plots. However, it seems that “CT w₁” plots were less affected than “CT w₃” plots with regard to bulk density increases under partial load. In contrast, diminishments of wide coarse pores (−6 kPa) and narrow (tight) coarse pores (−30 kPa) were significantly higher in “CT w₁” plots down to 0.4 m. Among CT plots, the best physical properties were obtained at medium soil water (w₂) content. No significant increase in bulk density and no significant decrease in coarse pore size porosity and total porosity below 0.2 m were observed at medium soil water content. The soil water content seemed to be the most decisive factor.It is likely that, CS (chiselling to a depth of 0.13 m followed by two passes of rotary harrow to a depth 0.05 m) plots were less affected by traffic treatments than CT plots. Considering the proportion of coarse pore size porosity (structural porosity) and total porosity, no compaction effects below 0.3 m were found. Medium soil water content (w₂) provides better soil conditions after traffic with regard to wide coarse pore size porosity (−6 kPa), air permeability (at 6 and 30 kPa water suction), total porosity and bulk density. Proportion of wide coarse pores, air permeability and bulk density seems to be suitable parameters to detect soil compaction under the conditions tested.     

Effect of soil compaction on hydraulic properties of two loess soils in China

Soil compaction affects hydraulic properties, and thus can lead to soil degradation and other adverse effects on environmental quality. This study evaluates the effects of three levels of compaction on the hydraulic properties of two silty loam soils from the Loess Plateau, China. Undisturbed soil cores were collected from the surface (0–5 cm) and subsurface (10–15 cm) layers at sites in Mizhi and Heyang in Shaanxi Province. The three levels of soil compaction were set by increasing soil bulk density by 0% (C0), 10% (C1) and 20% (C2) through compression and hammering in the laboratory. Soil water retention curves were then determined, and both saturated hydraulic conductivity (K_s) and unsaturated hydraulic conductivity were estimated for all of the samples using standard suction apparatus, a constant head method and the hot-air method, respectively. The high level of compaction (C2) significantly changed the water retention curves of both the surface and subsurface layers of the Heyang soil, and both levels of compaction (C1 and C2) changed the curves of the two layers from the Mizhi site. However, the effects of compaction on the two soils were only pronounced below water tensions of 100 kPa. Saturated hydraulic conductivities (K_s) were significantly reduced by the highest compaction level for both sampled layers of the Heyang soil, but no difference was observed in this respect between the C0 and C1 treatments. K_s values decreased with increasing soil compaction for both layers of the Mizhi soil. Unsaturated hydraulic conductivities were not affected by soil compaction levels in the measured water volume ratio range, and the values obtained were two to five orders of magnitude higher for the Mizhi soil than for the Heyang soil. The results indicate that soil compaction could strongly influence, in different ways, the hydraulic properties of the two soils.     

Effect of degree of fluid saturation on transport coefficients in disturbed soils

To improve the predictive capability of transport models in soils we need experimental data that improve their understanding of properties at the scale of pores, including the effect of degree of fluid saturation. All transport occurs in the same soil pore space, so that one may intuitively expect a link between the different transport coefficients and key geometrical characteristics of the pores such as tortuosity and connectivity, and pore‐size distribution. To understand the combined effects of pore geometry and pore‐size distribution better, we measured the effect of degree of water saturation on hydraulic conductivity and bulk soil electrical conductivity, and of degree of air saturation on air conductivity and gaseous diffusion for a fine sand and a sandy loam soil. To all measured data were fitted a general transport model that includes both pore geometry and pore‐size distribution parameters. The results show that both pore geometry and pore‐size distribution determine the functional relations between degree of saturation, hydraulic conductivity and air conductivity. The control of pore size on convective transport is more for soils with a wider pore‐size distribution. However, the relative contribution of pore‐size distribution is much larger for the unsaturated hydraulic conductivity than for gaseous phase transport. For the other transport coefficients, their saturation dependency could be described solely by the pore‐geometry term. The contribution of the latter to transport was much larger for transport in the air phase than in the water phase, supporting the view that connectivity dominates gaseous transport. Although the relation between effective fluid saturation and all four relative transport coefficients for the sand could be described by a single functional relation, the presence of a universal relationship between fluid saturation and transport for all soils is doubtful.     

Pore characteristics and hydraulic properties of a sandy loam supplied for a century with either animal manure or mineral fertilizers

Abstract Application of organic residues to soil is generally assumed to improve soil tilth. Only few studies have reported the long‐term effects on the more subtle aspects of soil porosity, and no reports have considered the potential effects of organic amendments on the pore system in the subsoil. We sampled undisturbed soil cores (100 cm³ and 6280 cm³) using metal cylinders in differently fertilized plots in the long‐term field experiment at Askov Experimental Station, Denmark. We selected the 0–60 cm soil layer of plots dressed for a century with either mineral fertilizers (labelled NPK) or animal manure (labelled AM) and unfertilized plots (UNF) as a reference. Both fertilization treatments were studied at two levels of nutrient application: ‘normal’ (labelled ‘1’) and 1.5 times ‘normal’ (labelled ‘1½’). Water retention, air permeability and air diffusivity were measured on the small cores, and we used the large cores for measuring near‐saturated and saturated hydraulic conductivity. In the plough layer, the AM and NPK soils displayed identical pore volumes in size fractions that were larger as well as smaller than 30 μm, while the UNF soil had a significantly smaller volume of pores < 30 μm. No clear trends were found in treatment effects on pore organization as calculated from air diffusivity and air permeability measurements. No significant differences in hydraulic conductivity were found in the plough layer. For the subsoil below ploughing depth, significantly larger macropore volumes and near‐saturated hydraulic conductivities were found for soil of plots receiving the larger (‘1½’) amount of nutrients compared with the ‘normally’ dressed soil. This effect was independent of fertilization system (AM or NPK). We attribute the larger volume of macropores to the improved root growth conditions in the soil with the higher nutrient level. We conclude that addition of animal manure at rates realistic in agriculture has only a modest effect on soil pore characteristics of the plough layer soil compared with the use of mineral fertilizers. For the subsoil below ploughing depth, a high level of nutrient application may increase soil macroporosity and near‐saturated hydraulic conductivity, but the origin of nutrients is of no significance.     

Using boosted regression trees to explore key factors controlling saturated and near‐saturated hydraulic conductivity

Hydraulic conductivity at and near saturation is difficult to predict. We investigated, for the first time, the potential of boosted regression trees to identify the key factors that determine saturated and near‐saturated hydraulic conductivities in undisturbed soils with a global meta‐database of tension infiltrometer measurements. Our results demonstrate that pedotransfer functions developed from meta‐databases may strongly over‐estimate prediction performance unless they are validated against each individual data source separately. For such a source‐wise cross‐validation, we estimated the hydraulic conductivity at a tension of 10 cm (K₁₀) and the saturated hydraulic conductivity (K_s) with coefficients of determination of 0.36 and 0.15, respectively. The most important predictors for K₁₀ were the average annual precipitation and temperature at the measurement location, which are key variables for pedogenesis and constrain soil management. More research is required for the in‐depth interpretation of their influence on hydraulic conductivity. The soil clay and organic carbon contents were also important predictors of K₁₀, with hydraulic conductivity decreasing as organic carbon contents increased up to 1.5% and as clay contents increased between about 10 and 40%. The direction of the tension‐sequence with which the infiltrometer data were collected was also a significant predictor. Land use and bulk density were the most important predictors for K_s. The direction of the tension‐sequence and the soil texture class were also important, with both coarse and fine‐textured soils generally having larger K_s values than medium‐textured soils.     

Estimation and analysis of soil hydraulic properties through infiltration experiments: comparison of BEST and DL fitting methods

The BEST method (Beerkan estimation of soil transfer parameters through infiltration experiments) appears promising and easy to estimate not only saturated hydraulic conductivity but also water retention and hydraulic characteristics. However, few tests have been conducted to test the methodology. This study involved field BEST infiltration experiments for three layers (surface, 15 and 30 cm) for each of three soils with different soil textures under grassland. By comparing BEST with DL (differentiated linearization method), we found that the DL method did not produce a good estimate of the soil hydraulic properties and neither did it identify the transient flow state. The BEST method resulted in reasonable results and is therefore promising. However, with BEST we encountered some anomalies when calculating hydraulic properties in some cases with too few data points under the transient flow state. We show that the application of BEST field experiments requires a wide range of soil water content from initial to saturated states so as to include sufficient transient flow. The soil hydraulic properties determined using the BEST method showed contrasting characteristics between different soil textures with higher saturated hydraulic conductivity under coarse texture and lower values under loam textures, especially with highly compacted soils. Vertical variation in soil hydraulic properties was significant, and the surface layer had a lower saturated hydraulic conductivity partly caused by compaction (high bulk density) or by remnants of grass plants. Further research on the effects of compaction and grass plants on soil hydraulic properties is needed.     

Soil structural indices' dependence on irrigation water quality and their association with chromophoric components in dissolved organic matter

Irrigation with treated wastewater (TWW) may affect soil structure and stability and the characteristics of dissolved organic matter (DOM) of the soil solution. The objectives of our study were (i) to evaluate the impact of TWW irrigation, as compared with fresh water (FW) irrigation, on aggregate stability and saturated hydraulic conductivity (indices of soil structure stability) and (ii) to determine whether these indices can be associated with the chromophoric indicators of water‐extractable DOM in TWW‐ and FW‐irrigated soils. We studied aggregate stability and soil hydraulic conductivity (HC) of four different soil types irrigated with either TWW (for at least 5 years) or FW. The results were linked to earlier published data on the concentration scores of fluorescent chromophoric DOM components (obtained from excitation‐emission matrices of flouorescence coupled with parallel factor analysis), dissolved organic carbon (DOC) concentration and absorbance at 254 nm (Abs254). These were all obtained from water extracts of the same soils as those used in the current study. Irrigation with TWW decreased aggregate stability, in comparison to irrigation with FW, in the sandy clay and clay soils, while in the loamy sand TWW increased aggregate stability. The apparent steady state HCs in the TWW‐irrigated samples in the loamy sand, sandy clay and clay soils were similar to, or significantly less than, those obtained in the FW‐irrigated samples. In the sandy loam the opposite trend was noted. Results of principal component and classification analyses showed that the aggregate stability indices were directly associated with soil organic matter and DOM attributes in the coarse‐textured soils, while in the fine‐textured soils inverse associations were noted. Only in the fine‐textured soils were the HC attributes associated (directly) with some of the DOM characteristics. Our results suggest that structural indices of fine‐textured soils are more sensitive than those of coarse‐textured soils to the composition of water extractable DOM.     

渭北果园土壤物理退化特征及其机理研究

【目的】针对我国渭北苹果主产区出现的随植果年限增加,果园土壤质量严重退化,树势衰弱、树体过早衰老、抗性降低、腐烂病及早期落叶病频繁发生,果品产量与品质下降等问题,开展了渭北苹果园土壤物理质量退化特征、退化机理及危害程度等问题的研究,以期查明制约果业可持续发展的因素,为果园土壤科学管理提供依据。【方法】在渭北黄土塬区选取了10 a、10 20 a、20 a 3个园龄段果园各4个,并以土壤条件相同的农田作对照,在果树冠层投影范围内距树干2/3处采取土样,测定土壤剖面不同层次容重、紧实度、孔隙度、饱和导水率、粘粒含量等物理性指标。【结果】渭北果园土壤容重和紧实度随园龄和土层深度的增加而增大,尤其在表层(20 cm)以下,土壤容重已经达到了1.45 1.61 g/cm3,紧实度达到933 2433 k Pa,严重超出果树健康生长的阈值。土壤孔隙度仅在0—20 cm土层能够保持在50%以上,属于良好状态,而20—60 cm土层维持在40%46%,已处于紧实和严重紧实状态。土壤饱和导水率在果园表层和紧实层均表现出随植果园龄的增大而减小的趋势,尤其是10 20 a和20 a的果园亚表层土壤饱和导水率低至46.88 cm/d和20.89 cm/d,制约着降水入渗和土壤蓄墒。3个园龄段果园土壤剖面上粘粒含量随土层深度呈递增趋势,且在0—30 cm土层随园龄的增加而明显减少,而在30 cm以下则随园龄的增加而呈递增趋势。进一步分析发现,粘粒含量与土壤容重、紧实度以及孔隙度之间呈极显著的相关关系。以压实密度(PD)为指标,对渭北果园土壤压实程度进行评估,发现渭北果园20 cm土层以下的土壤压实密度都在1.40 g/cm3以上,均达到了中度压实的程度,严重影响果树根系的健康生长及对养分的吸收。【结论】渭北果园20 cm以下的亚表层土壤孔隙密实、容重和紧实度增大,土壤饱和导水率递减是其土壤物理性质退化的主要特征,表层土壤粘粒的深层移动与淀积是土壤物理退化的主要过程和机理,果园土壤翻耕扰动少、对物理退化干预少是其土壤物理退化程度逐渐加剧的外在原因,土壤团聚体稳定性差是土壤物理状态退化的根本原因。     

Impact of short-term organic amendments incorporation on soil structure and hydrology in semiarid agricultural lands

Soil structure plays an important role in edaphic conditions and the environment. In this study, we investigated the effects of organic amendment on soil structure and hydraulic properties. A corn field in a semiarid land was separately amended with sheep manure compost at five different rates (2, 4, 6, 8 and 10 t/ha) and corn stover (6 t/ha) in combination with two decomposing agents. The soil structure of different amended soils was analyzed from the aggregate and pore domain perspectives. The internal pore structure of the soil was visualized through X-ray computed tomography and quantified using a pore-network model. Soil aggregate-size distribution and stability, saturated hydraulic conductivity, and water-retention curves were measured by sampling or in situ. The gas permeability and diffusivity of different amended soils were simulated based on the extracted pore networks. The aggregate stability of the amended soils was improved compared with the control, that is, the mean weight diameter increased and the percentage of aggregate destruction decreased. The stability of soil aggregates varied non-monotonically with the application rate of compost and decreased after treatment with corn stover and decomposing agents. The pore-network parameters including air-filled porosity, pore radius, throat length, and coordinate number increased for the amended soils compared with the control. The mean pore size increased with increasing compost incorporation rate. The saturated hydraulic conductivity of the compost-amended soils was higher than that of the control but varied quadratically with the application rate. The saturated hydraulic conductivity of soil treated with corn stover and decomposing agents was clearly higher than that without the agent and the control. The greater gas diffusivity and air permeability indicate that soil aeration improved following the incorporation of organic amendments. The air permeability versus air-filled porosity relationship followed a power law, and the gas diffusivity versus air-filled porosity relationship was characterized by a generalized density-corrected model regardless of amendment. The findings of this study can help improve the understanding of soil structure and hydrological function to organic fertilizer incorporation and further monitor the quality of soil structure through the pore space perspective.     

Effect of tillage and crop rotations on pore size distribution and soil hydraulic conductivity in sandy clay loam soil of the Indian Himalayas

Tillage management can affect crop growth by altering the pore size distribution, pore geometry and hydraulic properties of soil. In the present communication, the effect of different tillage management viz., conventional tillage (CT), minimum tillage (MT) and zero-tillage (ZT) and different crop rotations viz. [(soybean–wheat (S–W), soybean–lentil (S–L) and soybean–pea (S–P)] on pore size distribution and soil hydraulic conductivities [saturated hydraulic conductivity (K_sat) and unsaturated hydraulic conductivity {k(h)}] of a sandy clay loam soil was studied after 4 years prior to the experiment. Soil cores were collected after 4 year of the experiment at an interval of 75 mm up to 300 mm soil depth for measuring soil bulk density, soil water retention constant (b), pore size distribution, K_sat and k(h). Nine pressure levels (from 2 to 1500 kPa) were used to calculate pore size distribution and k(h). It was observed that b values at all the studied soil depths were higher under ZT than those observed under CT irrespective of the crop rotations. The values of soil bulk density observed under ZT were higher in 0–75 mm soil depth in all the crop rotations. But, among the crop rotations, soils under S–P and S–L rotations showed relatively lower bulk density values than S–W rotation. Average values of the volume fraction of total porosity with pores <7.5 μm in diameter (effective pores for retaining plant available water) were 0.557, 0.636 and 0.628 m³ m⁻³ under CT, MT and ZT; and 0.592, 0.610 and 0.626 m³ m⁻³ under S–W, S–L and S–P, respectively. In contrast, the average values of the volume fraction of total porosity with pores >150 μm in diameter (pores draining freely with gravity) were 0.124, 0.096 and 0.095 m³ m⁻³ under CT, MT and ZT; and 0.110, 0.104 and 0.101 m³ m⁻³ under S–W, S–L and S–P, respectively. Saturated hydraulic conductivity values in all the studied soil depths were significantly greater under ZT than those under CT (range from 300 to 344 mm day⁻¹). The observed k(h) values at 0–75 mm soil depth under ZT were significantly higher than those computed under CT at all the suction levels, except at −10, −100 and −400 kPa suction. Among the crop rotations, S–P rotation recorded significantly higher k(h) values than those under S–W and S–L rotations up to −40 kPa suction. The interaction effects of tillage and crop rotations affecting the k(h) values were found significant at all the soil water suctions. Both S–L and S–P rotations resulted in better soil water retention and transmission properties under ZT.     

Zur Bedeutung des Aggregierungsgrades für die Spannungsverteilung in strukturierten Böden

The effect of soil aggregation on stress distribution in structured soils The mechanical compressibility of arable soils can be described by preconsolidation load value and by the shear resistance parameters of the bulk soil and single aggregates. In order to quantify the effective stress equation must be also known the hydraulic properties of the soil in dependence of the intensity, kind, and number of loading events. The soil reacts as a rigid body at very fast wheeling speed inclusive a very pronounced stress attenuation in the top soil while stresses will be distributed in the soil threedimensionally to deeper depths at slower speed. These variations can be explained by the mechanical as well as by the hydraulic parameters of the bulk soil and single aggregates. Thus, the pore water pressure value of the bulk soil as a parameter of the effective stress equation further depends on the hydraulic properties of the inter- and intraaggregate pore system and continuity. As can be derived from the results the pore water pressure values are identical irrespective of the predessication for clayey polyhedres at high load while in coarse textured prisms the pore water pressure value depends on load and predryness. The consequences for soil strength under dynamic loading are shortly discussed.     

The evaporation method: Extending the measurement range of soil hydraulic properties using the air‐entry pressure of the ceramic cup

Knowledge of hydraulic functions is required for various hydrological and plant‐physiological studies. The evaporation method is frequently used for the simultaneous determination of hydraulic functions of unsaturated soil samples, i.e., the water‐retention curve and hydraulic‐conductivity function. All methodic variants of the evaporation method suffer from the limitation that the hydraulic functions can only be determined to a mean tension of ≈ 60 kPa. This is caused by the limited measurement range of the tensiometers of typically 80 kPa on the dry end. We present a new, cost‐ and time‐saving approach which overcomes this restriction. Using the air‐entry pressure of the tensiometer's porous ceramic cup as additional defined tension value allows the quantification of hydraulic functions up to close to the wilting point. The procedure is described, uncertainties are discussed, and measured as well as simulated test results are presented for soil samples of various origins, different textures (sand, loam, silt, clay, and peat) and variable dry bulk density. The experimental setup followed the system HYPROP which is a commercial device with vertically aligned tensiometers that is optimized to perform evaporation measurements. During the experiment leaked water from the tensiometer interior wets the surrounding soil of the tensiometer cup and can lead to a tension retardation as shown by simulation results. This effect is negligible when the tensiometers are embedded vertically. For coarsely textured soils and horizontal tensiometer alignment, however, the retardation must be considered for data evaluation.     

Different responses in bulk density and saturated hydraulic conductivity to soil deformation by logging machinery on a Ferralsol under native forest

Ferralsols have high structural stability, although structural degradation has been observed to result from forest to tillage or pasture conversion. An experimental series of forest skidder passes in an east Amazonian natural forest was performed for testing the effects of mechanical stress during selective logging operations on a clay‐rich Ferralsol under both dry and wet soil conditions. Distinct ruts formed up to 25 cm depth only under wet conditions. After nine passes the initially very low surface bulk density of between 0.69 and 0.80 g cm^?3 increased to 1.05 g cm^?3 in the wet soil and 0.92 g cm^?3 in the dry soil. Saturated hydraulic conductivities, initially >250 mm h^?1, declined to a minimum of around 10 mm h^?1 in the wet soil after the first pass, and in the dry soil more gradually after nine passes. The contrasting response of bulk density and saturated hydraulic conductivity is explained by exposure of subsoil material at the base of the ruts where macrostructure rapidly deteriorated under wet conditions. We attribute the resultant moderately high hydraulic conductivities to the formation of stable microaggregates with fine sand to coarse silt textures. We conclude that the topsoil macrostructure of Ferralsols is subject to similar deterioration to that of Luvisols in temperate zones. The stable microstructure prevents marked compaction and decrease in hydraulic conductivity under wetter and more plastic soil conditions. However, typical tropical storms may regularly exceed the infiltration capacity of the deformed soils. In the deeper ruts water may concentrate and cause surface run‐off, even in gently sloping areas. To avoid soil erosion, logging operations in sloping areas should therefore be restricted to dry soil conditions when rut formation is minimal.     

滩涂围垦农田土壤饱和导水率的影响因素及转换函数研究

确定苏北沿海滩涂围垦农田耕层土壤饱和导水率的影响因素,构建适合该区的土壤转换函数,是研究该区田间土壤水盐运动和盐渍化防控的重要前提。本文在该区典型地块实测土壤饱和导水率和相关土壤基本理化性质,探讨了该区土壤饱和导水率的剖面分布特点,对影响饱和导水率的土壤基本性质进行了主成分分析,并建立了用于该区饱和导水率间接估算的土壤转换函数。结果表明:滩涂围垦农田土壤饱和导水率随剖面深度增加呈表土层高、亚表层低、底土层又升高的趋势,20~40 cm土层饱和导水率最小,介于2.75~6.73 cm·d-1,属低透水强度;土壤容重随剖面深度增加表现出与饱和导水率相反的变化特点。除了容重、孔隙度、质地等物理因素外,土壤肥力、盐分等化学性质也是影响饱和导水率的重要因素;影响滩涂围垦农田土壤饱和导水率的因素可由持水特性、盐碱状况、养分特征和土壤质地4个主成分反映,其累计贡献率达78.17%。在Vereecken转换函数中引入土壤盐分后可提高预测精度,修正函数Vereecken_1是最适合滩涂围垦农区土壤、具有最佳预测精度的转换函数。本文构建的土壤转换函数,可通过较易获得的砂粒、黏粒、容重、盐分和有机质对耕层土壤饱和导水率进行较高精度的预测,其结果可为滩涂盐渍化农区田间尺度土壤饱和导水率间接估算以及水盐运动数值模拟提供支持。