共查询到20条相似文献,搜索用时 218 毫秒
1.
2.
李鹏程 《中国农村水利水电》1996,(4):41-43
根据电度表的计量原理,分析了三相三线制电路高、低压计量方式下的几种有功电能的实用接线,讨论了互感器保险丝熔断、电流(压)极性错误时的计量补算问题。 相似文献
3.
在电能计量管理中 ,由于电能表接线错误 ,断线(失压、断流 )所引起的计量误差较大 ,易被人们所发觉和重视。而由于电能表非常规接线或使用不当引起的计量误差较小 ,一般误差只在百分之几~十几 ,不易被人们所发觉与重视。但是 ,如果它乘以倍率所引起的误差却很大 ,且作为交易结算的电能计量装置要求公平、准确、合理的原则。因此 ,电能表常见非正规接线引起的计量误差同样不可忽视。现笔者列举低压有功电能表常见非正规接线引起的计量误差的现象 ,并加以粗浅分析和提出改正措施。1 引起误差的现象(1) 单相电能表 :11表乘 2 :即用一个单相 … 相似文献
4.
单相电能表计量三相电量时出现反转问题的分析郑岩天津市电力局供电设备修造厂天津地区农村电力计量工作中,通常采用两只单相电能表计量三相有功电能,其接线方式见图1。在此种接线方式下,对部分农电用户计量电量时经常出现其中一只电能表反转的现象。农电部门通常的计... 相似文献
5.
农用水泵的动力以电力为主。为了落实单泵核算管水责任制,实现耗电量定额承包、奖省罚超,解决当前农村普遍存在的农灌用电吃“大锅饭”的问题,节约水电资源、降低农灌成本,要对每台水泵安装电度表来进行计量。由于三相电度表的价格比单相电度表贵近5倍,对此我们设想,是否能用单相电度表来计量三相异步电动机耗电量?以便降低装表成本,加速单泵核算管水责任制的推行。因此,我们做了单相电度表计量三相异步电动机耗电量的可行性和正确度的 相似文献
6.
7.
8.
戴哲平 《中国农村水利水电》1994,(9)
零线串接故障对电能计量的影响戴哲平(湖南省新化县水电局417600)我县农村小水电自供区10kV配电变压器所安装的计量电能的装置,许多采用三个单相电度表零线串接的方法进行测量,以便监视三相负载的电度数。正常运行时,三个单相表分别测出每相负载的电度数,... 相似文献
9.
11.
12.
A swinging drag body flowmeter was designed and tested under laboratory conditions. The meter was designed to measure flowrate
in an irrigation water pipe. The meter consisted of a paddle, a rotating mechanism, and a potentiometer to measure paddle
position. The rotating mechanism was mounted in a head unit that was strapped to a water pipe. The paddle extended from the
rotating mechanism at the pipe wall, down through the center of the pipe. Drag and lift formulas were used to analyze flowmeter
behavior and determine if these equations could be used to develop other flowmeters of this design. The lab data showed a
strong correlation to the theoretical equations but there were significant errors between the two sets of data. The meter
behaved in a repeatable and stable manner over two months of lab testing. It is believed that this design is particularly
suited for irrigation pipe flow applications. 相似文献
13.
核子水分——密度仪是快速无损检测新设备,当前现场标定的误差校正方法有时偏差非常大,影响仪器的正常使用。针对现场标定中存在的问题,根据现场标定试验成果,采用数值分析方法,提出了几种适合校正砂土材料的分段偏差校正法、二次曲线法、二次曲面法以及线性校正法等误差校正方法,并通过对比分析,提出了最优校正方法。 相似文献
14.
为了掌握国产卷盘喷灌机水涡轮水力性能和能耗,构建了一种试验装置,其由供水泵、制动器、扭矩-转速传感器、测量仪组成。试验时调节制动器来改变负载大小从而调节水涡轮转速,通过测量流量以及进出口压力,得出水涡轮水头、水功率,扭矩仪测出转矩和转速等,从而得到水涡轮在各工况下的效率,试验分别测得了水涡轮在7种转速下的特性曲线。得出水涡轮的高效区范围,高效区功率大小,随着转速的降低,高效区向小流量偏移。试验结果说明,国产JP50卷盘喷灌机的水涡轮效率较低,有很大的节能空间 相似文献
15.
针对标准GB 18447-2008中前照灯近光照射在距离10 m远屏幕上的明暗截止线水平部分(或转折点)离地高度的规定,分析前照灯远、近光照射高度与拖拉机最小制动减速度时的最长制动距离的关系,得出前照灯远、近光照射在距离10 m远屏幕上离地高度的范围,并使远、近光照射落地距离满足驾驶员在夜间正常行驶车速下发现障碍物后所采取的减速措施安全有效。 相似文献
16.
17.
为进一步降低线损和提高供电可靠率,根据农村低压电力网的供电现状,提出配合单相小容量产品的单相二线、三线制供电方式。介绍低压单相供电的设计与实施方案,分析单相供电方式的电气性能、技术特点以及综合效益。 相似文献
18.
《Agricultural Water Management》2004,66(1):65-76
Various methods are used to estimate the canal seepage rate such as empirical formulae, analytical or analogue studies and the direct seepage measurement techniques, i.e. seepage meters, ponding tests and inflow–outflow tests. Considering significance of physical measurement techniques both ponding and inflow–outflow methods were used to evaluate the seepage losses. These methods have their merits, demerits and limitations which are well understood. However, while interpreting seepage loss evaluations, there can be independent random errors, like the fluctuations in flow conditions affecting different current meter positions, and systematic errors, like the use of different instruments or different methods to measure different terms in the balance. These errors have to be distinguished.The data from various studies in the region have been reviewed and analyzed. A statistical analysis of a number of replications of ponding and inflow–outflow test data of the seepage estimation work on various canals under the Fordwah Eastern Sadiqia (South) project, Bahawalnagar, Pakistan has been done to show the accuracy of results achieved through both the methods. It has been shown that the ponding method is more accurate than the inflow–outflow method as variability of various statistical parameters from the ponding tests is comparatively less. It is proved that inflow–outflow tests should not be used for seepage investigations where seepage rates are fairly small and there is no possibility to use sufficiently long reaches. 相似文献
19.
20.
针对现有玉米精密电驱排种控制系统无法快速适应多类型排种器排种控制的问题,在玉米CAN总线电动排种的基础上,设计了一种对玉米排种器排种驱动进行现场标定的电驱控制系统。系统在排种驱动电动机控制信号与排种盘转速之间的对应关系中,采用分段线性插值的方法现场获取排种器驱动曲线,实现排种盘转速标定与控制。以国产气吸式玉米精密排种器和指夹式玉米精密排种器为试验对象,在模拟车速下,对系统排种盘转速现场标定的控制准确性进行试验。电驱气吸式排种器排种盘转速控制性能试验中,株距设定为25 cm,车速设定为3~12 km/h(间隔3 km/h),结果表明,系统调节时间最长为0.80 s,稳态误差最大为0.81 r/min,控制精度最低为97.42%。电驱指夹式排种器排种盘转速控制性能试验中,株距分别设定为20、25、32 cm,车速设定为4~9 km/h(间隔1 km/h),结果表明,总体排种盘转速平均调节时间为1.09 s,标准差为0.26 s;总体平均稳态误差为0.38 r/min,标准差为0.23 r/min;总体平均控制精度为98.30%,标准差为1.01%。与分段PID排种转速控制系统控制性能进行对比得出,支持转速现场标定的系统具有更好的适应性,平均调节时间减少0.51 s,平均稳态误差增大0.16 r/min,平均控制精度降低0.63个百分点。选用指夹式排种器,进行了播种均匀性田间试验,株距为20 cm,车速范围为4~7 km/h(间隔1 km/h),结果表明,播种合格指数大于等于84.26%,变异系数小于等于18.29%,说明系统能够完成对玉米精密排种器排种转速控制曲线的高控制精度现场标定,能够精准控制电驱排种转速。 相似文献