Measurement and modelling of the effects of initial soil conditions and slope gradient on soil translocation by tillage

Tillage erosion studies have mainly focused on the effect of topography and cultivation practices on soil translocation during tillage. However, the possible effect of initial soil conditions on soil displacement and soil erosion during tillage have not been considered. This study aims at investigating the effect of the initial soil conditions on net soil displacement and the associated erosion rates by a given tillage operation of a stony loam soil. Tillage erosion experiments were carried out with a mouldboard plough on a freshly ploughed (pre-tilled) soil and a soil under grass fallow in the Alentejo region (Southern Portugal).

The experimental results show that both the downslope displacement of soil material and the rate of increase of the downslope displacement with slope gradient are greater when the soil is initially in a loose condition. This was attributed to: (i) a greater tillage depth on the pre-tilled soil and (ii) a reduced internal cohesion of the pre-tilled soil, allowing clods to roll and/or slide down the plough furrow after being overturned by the mouldboard plough.

An analysis of additional available data on soil translocation by mouldboard tillage showed that downslope displacement distances were only significantly related to the slope gradient when tillage is carried out in the downslope direction. When tillage is carried out in the upslope direction, the effect of slope gradient on upslope displacement distances was not significant. This has important implications for the estimation of the tillage transport coefficient, which is a measure for the intensity of tillage erosion, from experimental data. For our experiments, estimated values of the tillage transport coefficient were 70 and 254 kg m⁻¹ per tillage operation for grass fallow and pre-tilled conditions, respectively, corresponding to local maximum erosion rates of ca. 8 and 35 Mg ha⁻¹ per tillage operation and local maximum deposition rates of ca. 33 and 109 Mg ha⁻¹ per tillage operation.     

The effect of tillage direction on soil redistribution by mouldboard ploughing on complex slopes

Seven mouldboard ploughing experiments were conducted to systematically investigate the effect of different tillage directions on soil redistribution on hillslopes. The present study included tillage directions other than parallel to the gradient or along the contour, that is, in our experiments the slope gradient changed simultaneously in tillage and in turning direction. Using physical tracers we developed a model of the two-dimensional tracer displacement as a function of topography and tillage variables. The displacements in tillage and in turning direction were separately described as 2nd degree polynomials in both tillage and in turning directions. This model fully accounted for the directionality of tillage. Displacement in turning direction additionally depended on tillage depth, while that in tillage direction was affected by tillage speed and soil bulk density. We found a large effect of tillage directionality on soil redistribution, and tillage at 45° to the gradient turning soil upslope was the least erosive tillage direction. We obtained non-linear relationships between soil redistribution and profile curvature, instead of the linear relationships reported previously. Consequently tillage erosivity varied in tillage direction and a unique tillage transport coefficient could not be obtained for all tillage directions.     

Tillage translocation and tillage erosion in the complex upland landscapes of southwestern Ontario, Canada

Tillage translocation and tillage erosion were measured throughout the topographically complex landscapes of two fields in the upland region of southwestern Ontario. Translocation of soil by tillage was measured by labelling plots of soil with chloride and measuring the tracer's forward displacement in response to single passes by four tillage implements (mouldboard plough, chisel plough, tandem disc and field cultivator). The change in translocation within the landscape was used to measure tillage erosion. All four implements were erosive. A relationship between tillage translocation and slope gradient was observed; however, the variability in translocation could not be explained by slope gradient alone. Slope curvature was responsible for some translocation through the planning action of tillage implements. Tillage depth and speed were subject to considerable discontinuous and inconsistent manipulation by the operator in response to changing topographic and soil conditions. Tillage speed decreased by as much as 60% during upslope tillage and increased by as much as 30% during downslope tillage, relative to that on level ground. Tillage depth decreased by as much as 20% and increased by as much as 30%, relative to that on level ground. This manipulation is typical for tillage in complex landscapes and was presumed largely responsible for the variability in the results. The manipulation of tillage depth and speed are affected by the tractor-implement match and the responsiveness of the tillage operator.     

Implement and soil condition effects on tillage-induced erosion

Water, wind, or tillage-induced soil erosion can significantly degrade soil quality. Therefore, understanding soil displacement through tillage translocation is an important step toward developing tillage practices that do not degrade soil resources. Our primary objective was to determine the effects of soil condition (i.e. grassland stubble versus previously tilled soil), opening angle, and harrow speed on soil translocation. A second field study also conducted on a Lixisol but only in the stubble field, quantified displacement effects of mouldboard ploughing. The field studies were located 12 km South of Évora, Portugal. Soil displacement or translocation after each tillage operation in both studies was measured using aluminium cubes with a side length of 15 mm as ‘tracers’. Offset angles for the harrow disk were 20°, 44° and 59°; tractor velocities ranged from 1.9 to 7.0 km h⁻¹ and tillage depth ranged from 4 to 11 cm. The depth of mouldboard ploughing was approximately 40 cm with a wheel speed of 3.7 km h⁻¹. The translocation coefficients for the two implements were very different averaging 770 kg m⁻¹ for the mouldboard plough and ranging from 9 to 333 kg m⁻¹ for the harrow disk. This shows that the mouldboard plough was more erosive than the harrow disk in these studies. All three variables (soil condition, opening angle, and tillage velocity) were critical factors affecting the translocation coefficient for the harrow disk. Displacement distances were the largest for compacted soils (stubble field), with higher opening or offset angles, and at higher velocities. The results also showed significant correlation for (a) mean soil displacement in the direction of tillage and the slope gradient and (b) soil transport coefficient and the opening angle. Our results can be used to predict the transport coefficient (a potential soil quality indicator for tillage erosion) for the harrow disk, provided tillage depth, opening angle, and tool operating speed are known.     

等高犁耕朝向对紫色土坡面土壤再分布的影响

选择一块坡长15 m、坡度14.16%的坡地,采用磁性示踪法分析等高向下犁耕（向下坡方向翻垈）和等高向上犁耕（向上坡方向翻垈）的土壤再分布特征,利用模拟耕作（15次）检验两种等高犁耕的长期作用下对土壤剖面和微地貌演化的影响。结果表明:等高向下犁耕导致土壤发生向下坡移动,土壤位移量为15.62～28.70 kg/m,坡度对其影响不显著（p=0.93）;等高向上犁耕导致土壤同时发生向下坡和向上坡移动,土壤净位移量为-10.91～8.23 kg/m,坡度对其有显著影响（p < 0.001）,土壤净位移方向随着坡度的增大由向上坡转为向下坡,本研究条件下临界坡度为14%;等高向下犁耕15次后坡顶侵蚀深度是原土层深度的132%,耕作后土层深度与耕作深度相当,表明等高向下犁耕加速土壤侵蚀和促进母岩成土的双重作用共同维持着坡顶土层深度的稳定;等高向上犁耕15次后坡顶土层深度增加了12.7%,表明等高向上犁耕具有保护坡顶土层深度的作用。等高向上犁耕是一种防治类似紫色土的薄层土壤耕作侵蚀和土壤退化的有效措施。     

Assessment of tillage translocation and tillage erosion by hoeing on the steep land in hilly areas of Sichuan, China

Most of the tillage erosion studies have focused on the effect of tractor-plough tillage on soil translocation and soil loss. Only recently, have a few studies contributed to the understanding of tillage erosion by manual tillage. Furthermore, little is known about the impact of tillage erosion in hilly areas of the humid sub-tropics. This study on tillage erosion by hoeing was conducted on a purple soil (Regosols) of the steep land, in Jianyang County, Sichuan Province, southwestern China (30°24′N and 104°35′E) using the physical tracer method.

The effects of hoeing tillage on soil translocation on hillslopes are quite evident. The tillage transport coefficients were 26–38 kg m⁻¹ per tillage pass and 121–175 kg m⁻¹ per tillage pass respectively for k₃- and k₄-values. Given that there was a typical downslope parcel length of 15 m and two times of tillage per year in this area, the tillage erosion rates on the 4–43% hillslopes reached 48–151 Mg ha⁻¹ per year. The downslope soil translocation is closely related to slope gradient. Lateral soil translocation by such tillage is also obvious though it is lower than downslope soil translocation. Strong downslope translocation accounts for thin soil layers and the exposure of parent materials/rocks at the ridge tops and on convexities in the hilly areas. Deterioration in soil quality and therefore reduction in plant productivity due to tillage-induced erosion would be evident at the ridge tops and convex shoulders.     

Re-defining tillage erosion: quantifying intensity–direction relationships for complex terrain

Abstract. Current tillage erosion models account for the influence of tillage direction in the magnitude of the soil (tillage) transport coefficient. It is argued here that this is counter-intuitive and causes significant problems in modelling tillage erosion in areas of complex terrain. This article examines whether a re-modelling of tillage erosion is possible that separates tillage direction (an interaction with the landform) from the soil transport coefficient (a measure of tillage intensity representing the combination of implement erosivity and soil erodibility). Experimental data for mouldboard ploughing upslope, downslope and cross-slope at Coombe Barton Farm, Devon are examined. Integration of data for all directions into a single relationship, which relates translocation in the direction of tillage to slope in the direction of tillage and translocation perpendicular to tillage to slope perpendicular to tillage, is not possible using previously published methods of analysis. However, when total translocation distance is regressed against the tangent of the slope at 45° to the tillage direction (bisecting the tillage direction and the direction of overturning) it is found that a single relationship can be used to describe tillage in all three directions. Therefore, this relationship is used to determine a single value of the soil transport coefficient ( k _fTa) for constant soil and implement conditions but different tillage directions. This redefinition of tillage is important both for true estimation of tillage erosion severity, the adirectional coefficient being 40% larger than the directional coefficient, and for modelling of tillage erosion in complex terrain. These improvements are vital when tillage erosion simulation is used to direct soil conservation strategies.     

Soil displacement and tillage erosion during secondary tillage operations: the case of rotary harrow and seeding equipment

This study reports the results of a series of experiments that were set up on agricultural land in central Belgium to investigate soil translocation and erosivity resulting from a secondary tillage operation using an implement sequence of a rotary harrow and seeder. Aluminium cubes were used as tracers of soil movement. Results show that soil displacement resulting from tillage with such an implement sequence is far from insignificant. This is mainly related to the relatively shallow tillage depth as well as to the loose initial soil condition of such secondary tillage operations. The calculated value for the tillage transport coefficient k (123 kg m⁻¹ per tillage operation) is comparable with k-values from implements that are considered to be more erosive, like mouldboard and chisel implements. In conclusion, this study shows that tillage erosion not only results from relatively aggressive tillage operations such as mouldboard and chisel passes, but that secondary operations contribute significantly to soil displacement and tillage erosion.     

重庆中梁山岩溶区耕作侵蚀影响因素研究

在重庆市中梁山岩溶区用示踪法对坡耕地进行耕作试验研究。结果表明:锄头和铁锹耕作引起的土壤位移距离、位移量与坡度呈正相关,而踩锹引起的土壤位移距离、位移量则与含水量具有一定的相关性。在顺坡耕作时铁锹引起的土壤位移距离、位移量与锄头相近,但它们远远大于踩锹;等高耕作时铁锹引起的土壤位移距离、位移量是锄头的1.3~3.8倍左右。铁锹顺坡耕作引起的土壤位移距离、位移量是它等高耕作的2~2.4倍;锄头顺坡耕作引起的土壤位移距离、位移量是它等高的3~8.8倍。引起土壤位移量的大小顺序依次是:锄头顺坡>铁锹顺坡>铁锹等高>锄头等高>踩锹顺坡。     

Tillage erosion within potato production systems in Atlantic Canada: I. Measurement of tillage translocation by implements used in seedbed preparation

In Canada, there is growing acceptance that tillage erosion is a serious form of soil degradation and a threat to the sustainability of agriculture across the country. To date, the potential risk for tillage erosion within potato production systems has not been investigated. The objective of this study was to generate tillage translocation values for primary and secondary tillage implements common to seedbed preparation within conventionally and conservation tilled potato production systems in Atlantic Canada. Tillage translocation was measured for each implement by labelling a plot of soil with a tracer. The tracer redistribution along the path of tillage was used to generate a summation curve to calculate mean soil movement in the direction of tillage. The results show that each primary and secondary tillage operation moved vast quantities of soil and is potentially erosive. Maximum displacement distances were considerably larger in this project than those reported in previous studies looking at tillage erosion by primary and/or secondary tillage implements. All four tillage implements tested moved soil at least 3 m, with the greatest translocated distances (5.6 m) observed for the chisel plough (CP) and vibrashank (VS). The mass of translocated soil (T_M) was greatest for the CP, followed by the mouldboard plough (MP), VS and offset disc (OD). In addition, compared to travelling downslope, the upslope speed of tillage was reduced by 38%, 21%, 32% and 12% for the MP, CP, OD and VS, respectively, while the depth of tillage was reduced by 6%, 5%, 35% and 2%, respectively. It is apparent that conservation tillage implements (the CP is generally promoted to reduce water erosion in Atlantic Canada) and secondary tillage implements (OD and VS) can move as much soil as conventional tillage implements such as the mouldboard plough, and must be considered when developing plans to reduce soil erosion within potato fields in Atlantic Canada.     

Tillage translocation and tillage erosivity by planting, hilling and harvesting operations common to potato production in Atlantic Canada

In Canada, the negative impacts of tillage erosion is a growing concern, especially in regions where highly erosive cropping and tillage systems are practiced on highly erodible, topographically complex landscapes. To date, tillage erosion studies have focused primarily on the movement of soil by primary and secondary tillage operations. However, in potato (Solanum tuberosum L.) production there is often considerable soil disturbance that occurs during “tertiary” field operations conducted during the growing season. Therefore, the objective of this project was to generate tillage translocation and erosivity values for implements common to planting, hilling and harvesting operations within intensive potato production systems in Atlantic Canada. Our results show that tertiary tillage operations result in significant soil displacement and can be equally as erosive as primary and secondary tillage operations. Both the planting, cultivating and hilling (PCH) sequence and the harvester moved soil extremely large distances (up to 23.6 and 6.0 m, respectively). In fact, the mean translocated distance of the tilled layer (T_L) and the mass of translocated soil (T_M) of the PCH sequence (0.42 m and 115.9 kg m⁻¹, respectively) and the harvester (0.55 m and 71.7 kg m⁻¹, respectively) are larger than those reported previously for primary and secondary tillage operations in New Brunswick. In addition, the net downslope movement of soil for the PCH sequence and the harvester was approximately 36 and 26 kg m⁻¹, respectively, suggesting that both tertiary tillage operations have the potential to be erosive. A direct relationship was observed between both T_L and T_M and slope gradient for the PCH sequence, but similar relationships were not found for the harvester, even though the harvester moved approximately 30 % more soil downslope than upslope. Linear regression functions were generally improved after including slope curvature in the model, but these results were not always significant. Soil movement by the PCH sequence and harvester were also largely influenced by tillage speed and tillage depth, and future research is needed under controlled conditions to determine whether it is changing topography or the variability in tillage speed and depth across the landscape in response to changing topography that is driving tillage erosion within mechanized agricultural systems. It is clear that tertiary tillage operations must be considered when developing best management practices to improve soil conservation strategies for potato production systems in Canada and worldwide.     

Influences of tillage operations on soil translocation over sloping land by hoeing tillage

Very few studies have investigated the factors affecting soil displacement and tillage erosion by hoeing tillage. This study adopted a magnetic tracer method to investigate the influences of hoe form and tillage depth on soil translocation over steep hillslopes in Southwest China using a new type of magnetic tracer, i.e., ilmenite powder. Ilmenite powder enhanced the magnetic sensitivity of soil at the end position of tracer distribution, and improved the accuracy and efficiency of tillage translocation measurements. Tillage translocation by wide and perforated hoes was found to be significantly correlated with slope gradient (P < 0.01), however, no significant correlation was found for narrow and bidentate hoe tillage (P > 0.05). Compared with wide hoes, the tillage erosion rates resulting from the use of narrow, perforated and bidentate hoes were reduced by 12.4%, 11.0%, and 16.3%, respectively, indicating that changes in hoe forms resulted in a marked decrease in downslope soil translocation and tillage erosion. Tillage erosion rate decreased by 64% when the tillage depth was reduced from 0.26 to 0.14 m. These results suggest that innovations in hoe form and reductions in tillage depth are important means to manage tillage erosion due to hoeing.     

Modelling tillage erosion in the topographically complex landscapes of southwestern Ontario, Canada

A tillage erosion model was developed for southwestern Ontario based on the relationship between tillage translocation and slope gradient and slope curvature. Two studies of tillage translocation and tillage erosion were used to calibrate this model, one a comparison of upslope and downslope tillage translocation on shoulder slopes, the other an examination of tillage translocation throughout topographically complex landscapes. Two field sites were used for validation of the model. For both sites, past tillage practices were known and past soil erosion was determined using ¹³⁷Cs as an indicator of soil redistribution. The model accurately predicted the pattern of soil redistribution that had occurred within the two field sites. Severe soil loss was observed and predicted on convex landscape positions and soil accumulation was observed and predicted on concave landscape positions. The model accounted for almost all of the soil lost from the convex upper slope positions where tillage erosion was expected to be the dominant erosion process. There was considerable soil loss and accumulation elsewhere in the landscapes which could not be accounted for by the model and was presumed to be primarily the result of water erosion. It was concluded that tillage erosion must be incorporated into soil erosion modelling for the purposes of soil conservation.     

东北黑土区典型坡面耕作侵蚀定量分析

东北黑土区水土流失主要集中在坡耕地,以往研究多关注水蚀而忽略了耕作侵蚀的存在。为印证并定量描述黑土耕作侵蚀,该文采用物理示踪法,测定了典型坡耕地耕作位移量及其分布格局。结果表明:铧式犁耕作后示踪剂沿耕作方向发生扩散,上坡耕作示踪剂集中分布在0~20 cm范围,而下坡耕作示踪剂集中分布在0~20和50~150 cm。一次耕作引起的耕作位移量为32.68~134.14 kg/m,耕作迁移系数234 kg/m。坡度是影响耕作位移的重要因素,二者呈显著的正相关关系,且对上坡耕作的影响大于下坡耕作。研究区耕作年侵蚀速率0.4~11.0 Mg/(hm2·a),凸起的坡背、坡肩处及坡度较大的位置侵蚀严重。虽然黑土区坡度较小,但由于耕作深度大,速度快,耕作侵蚀严重,应引起足够重视。     

Quantifying tillage translocation and deposition rates due to moldboard plowing in the Palouse region of the Pacific Northwest, USA

Most of the erosion research in the Palouse region of eastern Washington State, USA has focused on quantifying the rates and patterns of water erosion for purposes of conservation planing. Tillage translocation, however, has largely been overlooked as a significant geomorphic process on Palouse hillslopes. Tillage translocation and tillage deposition together have resulted in severe soil degradation in many steep croplands of the Palouse region. Few controlled experiments have heretofore been conducted to model these important geomorphic processes on Palouse hillslopes. The overarching purpose of this investigation, therefore, was to model tillage translocation and deposition due to moldboard plowing in the Palouse region. Soil movement by moldboard plowing was measured using 480-steel flat washers. Washers were buried in silt loam soils on convex–convex shoulder, linear-convex backslope, and linear-concave footslope landform components, and then displaced from their original burial locations by a moldboard plow pulled by a wheel tractor traveling parallel to the contour at ca. 1.0 m s⁻¹. Displaced washers were located using a metal detector, and the distance and azimuth of the resultant displacement of each washer from its original burial location was measured using compass and tape. Resultant displacement distances were then resolved into their component vectors of displacement parallel and perpendicular to the contour. A linear regression equation was developed expressing mean soil displacement distance as a function of slope gradient. Tillage translocation and deposition were modeled as diffusion-type geomorphic processes, and their rates were described in terms of the diffusion constant (k). A multivariate statistical model was developed expressing mean soil displacement distance as a function of gravimetric moisture content, soil bulk density, slope gradient, and direction of furrow slice displacement. Analysis of variance (ANOVA) revealed a weak correlation between soil displacement and both bulk density and moisture content. Soil displacement was, however, significantly correlated with direction of furrow slice displacement. Tillage translocation rates were expressed in terms of the diffusion constant (k) and ranged from 105 to 113 kg m⁻¹ per tillage operation. Tillage deposition rates ranged from 54 to 148 kg m⁻¹ per tillage operation. With respect to tillage deposition, the diffusion constant calculated from volumetric measurements of tillage deposits equals ca. 150 kg/m. The rates of tillage translocation and deposition are not completely in balance; however, these rates do suggest that soil tillage is a significant geomorphic process on Palouse hillslopes and could account for the some of the variations in soil physical properties and crop yield potential at the hillslope and farm-field scale in the Palouse region.     

Soil carbon dioxide fluxes following tillage in semiarid Mediterranean agroecosystems

In semiarid Mediterranean agroecosystems, low and erratic annual rainfall together with the widespread use of mouldboard ploughing (conventional tillage, CT), as the main traditional tillage practice, has led to a depletion of soil organic matter (SOM) and with increases in CO₂ emissions from soil to the atmosphere. In this study, we evaluated the viability of conservation tillage: RT, reduced tillage (chisel and cultivator ploughing) and, especially, NT (no-tillage) to reduce short-term (from 0 to 48 h after a tillage operation) and mid-term (from 0 h to several days since tillage operation) tillage-induced CO₂ emissions. The study was conducted in three long-term tillage experiments located at different sites of the Ebro river valley (NE Spain) across a precipitation gradient. Soils were classified as: Fluventic Xerocrept, Typic Xerofluvent and Xerollic Calciorthid. Soil temperature and water content were also measured in order to determine their influence on tillage-induced CO₂ fluxes. The majority of the CO₂ flux measured immediately after tillage ranged from 0.17 to 6 g CO₂ m⁻² h⁻¹ and was from 3 to 15 times greater than the flux before tillage operations, except in NT where soil CO₂ flux was low and steady during the whole study period. Mid-term CO₂ emission showed a different trend depending on the time of the year in which tillage was implemented. Microclimatic soil conditions (soil temperature and water content) had little impact on soil CO₂ emission following tillage. In the semiarid Mediterranean agroecosystems studied, NT had low short-term soil CO₂ efflux compared with other soil tillage systems (e.g., conventional and reduced tillage) and therefore can be recommended to better manage C in soil.     

Fine-earth translocation by tillage in stony soils in the Guadalentin, south-east Spain: an investigation using caesium-134

Tillage erosion is increasingly recognised as an important soil erosion process on agricultural land. In view of its potential significance, there is a clear need to broaden the experimental database for the magnitude of tillage erosion to include a range of tillage implements and agricultural environments. The study discussed in this paper sought to address the need for such data by examining tillage erosion by a duckfoot chisel plough in stony soils on steep slopes in a semi-arid environment. Results of the investigation of coarse fraction (rock fragment) translocation by tillage in this environment have been presented elsewhere and the paper focuses on tillage translocation and erosion of the fine earth. Tillage translocation was measured at 10 sites, representing both upslope and downslope tillage by a duckfoot chisel plough on five different slopes, with tangents ranging from 0.02 to 0.41. A fine-earth tracer, comprising fine earth labelled with ¹³⁴Cs, was introduced into the plough layer before tillage. After a single pass of the plough, incremental samples of plough soil were excavated and sieved to separate the fine earth from the rock fragments. Translocation of the fine-earth tracer was established by analysing the ¹³⁴Cs content of the samples of fine earth. These data were used to establish translocation distances for each combination of slope and tillage direction. Translocation distances of the fine earth were not significantly different from translocation distances of the coarse fraction. For all sites, except uphill on the 0.41 slope, translocation distances were found to be linearly related to slope tangent. The soil flux due to tillage for each site was calculated using the translocation distance and the mass per unit area of the plough layer. For slopes with tangents <0.25, the relationship between soil flux and tangent was linear and the soil flux coefficient derived was 520–660 kg m⁻¹ per pass. This is much larger than the coefficients found in other studies and this high magnitude is attributed to the non-cohesive nature and high rock fragment content of the soil in this investigation. A second contrast with previous studies was found in non-linearity in the relationship between soil flux and tangent when steeper slopes were included. This was a product of variation in plough depth between the steepest slopes and the remainder of the study area. On the basis of the study it is suggested that an improved understanding of tillage erosion may be obtained by considering the dual processes of tillage detachment (mass per unit area of soil subject to tillage) and tillage displacement (equivalent to translocation distance per pass) in assessing, comparing and modelling tillage translocation. An improved model is proposed that recognises the complexity of soil redistribution by tillage, provides a framework for process-based investigation of the controls on tillage fluxes, and allows identification of potential self-limiting conditions for tillage erosion.     

Soil translocation resulting from multiple passes of tillage under normal field operating conditions

Until now, most tillage erosion experiments were conducted under controlled soil and operating conditions. However, soil condition, tillage depth, speed and direction generally show substantial within-field variation. In this study, a series of tillage experiments were set up to investigate the erosivity of tillage under normal operating conditions. The effect of a typical tillage sequence, including multiple mouldboard, chisel and harrow passes, on soil translocation and tillage erosion was studied during a period of 3 years. Soil translocation in excess of 10 m was observed while the average net translocation rates ranged between 0 and 0.9 m. The results suggest that the annual tillage transport coefficient, associated with mechanized agriculture, is in the order of 781 kg m⁻¹ yr⁻¹. The experimental results also show that the tillage transport coefficient of a sequence of tillage operations can be reasonably well predicted from information provided by the farmer and by summing the transport coefficients obtained from controlled, single pass experiments. However, a Monte Carlo simulation showed that a relatively high number of tillage operations are required to obtain accurate estimates of the tillage transport coefficients in multiple pass experiments.     

Characterization of soil physical properties and organic matter under long-term primary tillage in a humid climate

Chisel ploughing is considered to be a potential conservation tillage method to replace mouldboard ploughing for annual crops in the cool-humid climate of eastern Canada. To assess possible changes in some soil physical and biological properties due to differences in annual primary tillage, a study was conducted for 9 years in Prince Edward Island on a Tignish loam, a well-drained Podzoluvisol, to characterize several mouldboard and chisel ploughing systems (at 25 cm), under conditions of similar crop productivity. The influence of primary tillage on the degree of soil loosening, soil permeability, and both organic matter distribution throughout the soil profile and organic matter content in soil particle size fractions was determined. At the time of tillage, chisel ploughing provided a coarser soil macrostructure than mouldboard ploughing. Mouldboard ploughing increased soil loosening at the lower depth of the tillage zone compared to chisel ploughing. These transient differences between primary tillage treatments had little effect on overall soil profile permeability and hydraulic properties of the tilled/non-tilled interface at the 15–30 cm soil depth. Although soil microbial biomass, on a volume basis, was increased by 30% at the 0–10 cm soil depth under chisel ploughing, no differences were evident between tillage systems over the total tillage depth. Mouldboard ploughing increased total orgainc carbon by 43% at the 20–30 cm soil depth, and the carbon and nitrogen in the organic matter fraction ≤ 53 μm by 18–44% at the 10–30 cm soil depth, compared to chisel ploughing.     

Reassessment of tillage erosion rates by manual tillage on steep slopes in northern Thailand

Changing land-use practices in northern Thailand have increased tillage intensity. This study re-assesses the rate of tillage erosion by manual hoeing on steep slopes (17–82%) in northern Thailand. Previously collected soil translocation data during an on-farm tillage erosion experiment and additionally collected data during an on-farm tillage erosion survey have been analysed whereby a new calculation method (i.e. trapezoid tillage step) has been used. A comparison with previously collected data indicates that the trapezoid tillage step method and the tracer method are the most reliable methods to assess downslope translocation by manual tillage. Based on newly acquired understanding of the processes involved, soil fluxes by tillage erosion are quantified by linear functions for different slope gradient classes rather than one single diffusion-type equation for the whole slope range. For slope gradients smaller than 3%, soil fluxes are close to zero as farmers do not have a preferred tillage direction. For slope gradients between 3% and 70%, soil is tilled only in the downslope direction and soil fluxes range between 16 and 67 kg m⁻¹ tillage pass⁻¹. On slopes with gradients in excess of 70%, the angle of repose for soil clods is often exceeded resulting in a sliding down of the complete tilled top layer. These data are used to assess the soil flux for complete cropping cycles for the most dominant cropping systems in the highlands of northern Thailand: i.e. upland rice, maize, (soy) beans, cabbage and ginger. The on-site effects of tillage erosion will be very pronounced if parcels are short with respect to their slope length, cultivated for upland rice or cabbage, or when weed pressure is high. Tillage erosion results in a tillage step with low soil fertility and low infiltration capacity. Solutions to reduce tillage erosion intensity depend on the degree that tillage intensity can be reduced. This might happen by an improved weed management or by changing landuse to perrenial cropping. Other strategies are concentrating nutrients on the truncated hillslope sections and retaining soil on the field by vegetative buffers.