The feasibility of remotely sensed data to estimate urban tree dimensions and biomass

Accurately measuring the biophysical dimensions of urban trees, such as crown diameter, stem diameter, height, and biomass, is essential for quantifying their collective benefits as an urban forest. However, the cost of directly measuring thousands or millions of individual trees through field surveys can be prohibitive. Supplementing field surveys with remotely sensed data can reduce costs if measurements derived from remotely sensed data are accurate. This study identifies and measures the errors incurred in estimating key tree dimensions from two types of remotely sensed data: high-resolution aerial imagery and LiDAR (Light Detection and Ranging). Using Sacramento, CA, as the study site, we obtained field-measured dimensions of 20 predominant species of street trees, including 30–60 randomly selected trees of each species. For each of the 802 trees crown diameter was estimated from the aerial photo and compared with the field-measured crown diameter. Three curve-fitting equations were tested using field measurements to derive diameter at breast height (DBH) (r² = 0.883, RMSE = 10.32 cm) from the crown diameter. The accuracy of tree height extracted from the LiDAR-based surface model was compared with the field-measured height (RMSE = 1.64 m). We found that the DBH and tree height extracted from the remotely sensed data were lower than their respective field-measured values without adjustment. The magnitude of differences in these measures tended to be larger for smaller-stature trees than for larger stature species. Using DBH and tree height calculated from remotely sensed data, aboveground biomass (r² = 0.881, RMSE = 799.2 kg) was calculated for individual tree and compared with results from field-measured DBH and height. We present guidelines for identifying potential errors in each step of data processing. These findings inform the development of procedures for monitoring tree growth with remote sensing and for calculating single tree level carbon storage using DBH from crown diameter and tree height in the urban forest.     

Current and potential carbon stocks of trees in urban parking lots in towns of the Eastern Cape,South Africa

Greening of shopping centre parking lots is a potentially important strategy that can contribute to urban carbon mitigation efforts, improve aesthetics and the shopping experience of consumers, whilst adding to urban biodiversity. Twenty-eight shopping centre parking lots in six Eastern Cape urban centres, South Africa, were sampled to determine tree species composition, density and annual carbon sequestration potential. The best case parking lot found during the study was used as a benchmark to display the difference between current tree density and above-ground carbon stocks relative to the potential optimum. The highest tree density was 66 trees ha^?1, whereas the average density across all sampled parking lots was less than half that (27.2 ± 22.6 trees ha^?1). The average annual carbon sequestration potential per parking lot was 1390 ± 2503 kg ha^?1. Planting density was positively related to annual sequestration rates, whilst parking lot age and the mean annual rainfall of the town had no influence. Mean tree species richness per parking lot was 2.3 ± 1.8 species, with a positive relationship to parking lot size, but not to mean annual rainfall of the site. The majority of trees (62.5%) in parking lots were alien species, although newer parking lots had significantly greater proportions of indigenous species. There was no difference in mean annual carbon sequestration rate per tree between indigenous and alien trees species. Low tree densities and small parking lot areas constrained the potential for earning carbon credits from trees in parking lots. Nonetheless, planners and designers need to be more aware of the potential contribution of trees towards urban sustainability.     

The overlooked carbon loss due to decayed wood in urban trees

Decayed wood is a common issue in urban trees that deteriorates tree vitality over time, yet its effect on biomass yield therefore stored carbon has been overlooked. We mapped the occurrence and calculated the extent of decayed wood in standing Ulmus procera, Platanus × acerifolia and Corymbia maculata trees. The main stem of 43 trees was measured every metre from the ground to the top by two skilled arborists. All trees were micro-drilled in two to four axes at three points along the stem (0.3 m, 1.3 m, 2.3 m), and at the tree’s live crown. A total of 300 drilling profiles were assessed for decay. Simple linear regression analysis tested the correlation of decayed wood (cm²) against a vitality index and stem DBH. Decay was more frequent and extensive in U. procera, than P. acerifolia and least in C. maculata. Decay was found to be distributed in three different ways in the three different genera. For U. procera, decay did appear to be distributed as a column from the base to the live crown; whereas, decay was distributed as a cone-shape in P. acerifolia and was less likely to be located beyond 2.3 m. In C. maculata decay was distributed as pockets of variable shape and size. The vitality index showed a weak but not significant correlation with the proportion of decayed wood for P. acerifolia and C. maculata but not for U. procera. However, in U. procera, a strong and significant relationship was found between DBH and stem volume loss (R² = 0.8006, P = 0.0046, n = 15). The actual volume loss ranged from 0.17 to 0.75 m³, equivalent to 5%–25% of the stem volume. The carbon loss due to decayed wood for all species ranged between 69–110 kg per tree. Based on model’s calculation, the stem volume of U. procera trees with DBH ≥ 40 cm needs to be discounted by a factor of 13% due to decayed wood regardless of the vitality index. Decayed wood reduces significantly the tree’s standing volume and needs to be considered to better assess the carbon storage potential of urban forests.     

Rainfall interception and stem flow by eucalypt street trees – The impacts of canopy density and bark type

Understanding how trees influence water movement in an urban landscape is important because in an ‘engineered xeriscape’ small changes in rainfall frequency or magnitude have significant implications to plant water availability and mortality at one extreme, and stormwater runoff and flooding at the other. This study relates direct measures of tree canopy interception and discusses their implication for catchment hydrology in different urban landscape contexts. We measured canopy throughfall and stemflow under two eucalypt tree species in an urban street setting over a continuous five month period. Eucalyptus nicholii has a dense canopy and rough bark, whereas Eucalyptus saligna has a less-dense canopy and smooth bark. E. nicholii, with the greater plant area index, intercepted more of the smaller rainfall events, such that 44% of annual rainfall was intercepted as compared to 29% for the less dense E. saligna canopy (2010). Stemflow was less in amount and frequency for the rough barked E. nicholii as compared to the smooth barked E. saligna. However, annual estimates of stemflow to the ground surface for even the smooth barked E. saligna would only offset approximately 10 mm of the 200 mm intercepted by its canopy (2010).Tree canopy and bark characteristics should be considered when planting in pervious green space, or impervious streetscapes, because of their profound impact upon tree and surrounding water availability, soil water recharge or runoff. This study provides an evidence base for tree canopy impacts upon urban catchment hydrology, and suggests that rainfall and runoff reductions of up to 20% are quite possible in impervious streetscapes. Street tree canopies can function as a cost-effective compliment to water sensitive urban design for stormwater reduction benefits.     

Assessing the performance of urban forest carbon sequestration models using direct measurements of tree growth

Across cities worldwide, people are recognizing the value of greenspace in ameliorating the health and well-being of those living there, and are investing significant resources to improve their greenspace. Although models have been developed to allow the quantification of ecosystem services provided by urban trees, refinement and calibration of these models with more accurate site- and species-specific data can increase confidence in their outcomes. We used data from two street tree surveys in Cambridge, MA, to estimate annual tree mortality for 592 trees and diameter growth rates for 498 trees. Overall tree turnover between 2012 and 2015 was relatively low (annualized 3.6% y⁻¹), and mortality rate varied by species. Tree growth rates also varied by species and size. We used stem diameter (DBH) and species identity to estimate CO₂ sequestration rates for each of 463 trees using three different model variations: (1) i-Tree Streets, (2) Urban Tree Database (UTD) species-specific biomass allometries and growth rates, and (3) empirically measured growth rates combined with UTD biomass allometries (Empirical + UTD). For most species, the rate of CO₂ sequestration varied significantly with the model used. CO₂ sequestration estimates calculated using i-Tree Streets were often higher than estimates calculated with the UTD equations. CO₂ sequestration estimates were often the lowest when calculated using empirical tree growth estimates and the UTD equations (Empirical + UTD). The differences among CO₂ sequestration estimates were highest for large trees. When scaled up to the entire city, CO₂ sequestration estimates for the Empirical + UTD model were 49.2% and 56.5% of the i-Tree Streets and UTD estimates, respectively. We suggest future derivations of ecosystem service provision models allow localities to input their own species-specific growth values. By adding capacity to easy-to-use tools, such as i-Tree Streets, we can increase confidence in the model output.     

Private residential urban forest structure and carbon storage in a moderate-sized urban area in the Midwest,United States

In conjunction with urbanization and its importance as a major driver of land-use change, increased efforts have been placed on understanding urban forests and the provisioning of ecosystem services. However, very little research has been conducted on private property and little is known about the structure and function of privately owned urban forests. This research examines the structure of and carbon storage services provided by private residential urban forests in a moderate-sized Midwestern city. The primary research questions are as follows: What is the structure of private urban forests, and how does it vary across parcels? How much carbon is stored in tree and soil pools of private urban forests, and how does carbon vary across parcels? Ecological inventories were conducted on 100 residential parcels within 14 Neighborhood and Homeowners Associations of varying size and development age. Tree species richness, diversity, density, and diameter distribution were determined on a per parcel basis and for the entire tree population sampled. Further, tree and soil carbon storage were determined for each parcel. Results of this research demonstrated large variability in per-parcel tree metrics. Twelve of the parcels sampled had two or fewer trees, while eleven had greater than 50 trees. Further, tree carbon storage ranged from no carbon to 11.22 kg C m^?2. Alternatively, soil carbon storage was less variable and averaged 4.7 kg C m^?2, approximately 1.9 times higher than the average carbon stored in trees (2.5 kg C m^?2). Management efforts aimed at maintaining or enhancing carbon storage and other ecosystem services should focus on both soil protection and maximizing services in living biomass. Our results demonstrate that sustaining tree-produced ecosystem services requires maintenance of large old trees and species diversity, not only in terms of relative abundance, but also relative dominance, and in combination, species–specific size distributions.     

Relationships between bole and crown size for young urban trees in the northeastern USA

Knowledge of allometric equations can enable urban forest managers to meet desired economic, social, and ecological goals. However, there remains limited regional data on young tree growth within the urban landscape. The objective of this study is to address this research gap and examine interactions between age, bole size and crown dimensions of young urban trees in New Haven, CT, USA to identify allometric relationships and generate predictive growth equations useful for the region. This study examines the 10 most common species from a census of 1474 community planted trees (ages 4–16). Regressions were applied to relate diameter at breast height (dbh), age (years since transplanting), tree height, crown diameter and crown volume. Across all ten species each allometric relationship was statistically (p < 0.001) significant at an α-level of 0.05. Consistently, shade trees demonstrated stronger relationships than ornamental trees. Crown diameter and dbh displayed the strongest fit with eight of the ten species having an R² > 0.70. Crown volume exhibited a good fit for each of the shade tree species (R² > 0.85), while the coefficients of determination for the ornamentals varied (0.38 < R² < 0.73). In the model predicting height from dbh, ornamentals displayed the lowest R² (0.33 < R² < 0.55) while shade trees represented a much better fit (R² > 0.66). Allometric relationships can be used to develop spacing guidelines for commonly planted urban trees. These correlations will better equip forest managers to predict the growth of urban trees, thereby improving the management and maintenance of New England's urban forests.     

Density,diversity and richness of woody plants in urban green spaces: A case study in Chennai metropolitan city

A tree diversity inventory was carried out in urban green spaces (UGSs) of Chennai metropolitan city, India. This inventory aims to study the diversity, density and richness of trees in UGSs of Chennai. A total of one hundred 10 m × 10 m (total 1 ha) plots were laid to reveal tree diversity and richness of UGSs. Trees with ≥10 cm girths at breast height (gbh) were inventoried. We recorded 45 species in 42 genera and 21 families. Caesalpiniaceae and Fabaceae each with 6 species dominated the study area followed by Arecaceae (3). Density and stand basal area of the present study were 500 stems ha^?1 and 64.16 m², respectively. Most of the inventoried trees were native (31 species) and deciduous (28 species). Fabaceae and Caesalpiniaceae dominated the present study area in terms of stand basal area and density. The Shannon diversity index and evenness of study area were 2.79 and 0.73, respectively. The most important species and families based on species important value index (IVI) and family important value index were Albizia saman, Polyalthia longifolia and Azadirachta indica; Fabaceae, Caesalpiniaceae and Annonaceae respectively. We find Chennai's urban forest is relatively superior to many urban forests of the world in terms of stand basal area and species richness. Results emphasize the importance of enhancement of urban green spaces in Chennai metropolitan city.     

Data quality in citizen science urban tree inventories

Citizen science has been gaining popularity in ecological research and resource management in general and in urban forestry specifically. As municipalities and nonprofits engage volunteers in tree data collection, it is critical to understand data quality. We investigated observation error by comparing street tree data collected by experts to data collected by less experienced field crews in Lombard, IL; Grand Rapids, MI; Philadelphia, PA; and Malmö, Sweden. Participants occasionally missed trees (1.2%) or counted extra trees (1.0%). Participants were approximately 90% consistent with experts for site type, land use, dieback, and genus identification. Within correct genera, participants recorded species consistent with experts for 84.8% of trees. Mortality status was highly consistent (99.8% of live trees correctly reported as such), however, there were few standing dead trees overall to evaluate this issue. Crown transparency and wood condition had the poorest performance and participants expressed concerns with these variables; we conclude that these variables should be dropped from future citizen science projects. In measuring diameter at breast height (DBH), participants had challenges with multi-stemmed trees. For single-stem trees, DBH measured by participants matched expert values exactly for 20.2% of trees, within 0.254 cm for 54.4%, and within 2.54 cm for 93.3%. Participants’ DBH values were slightly larger than expert DBH on average (+0.33 cm), indicating systematic bias. Volunteer data collection may be a viable option for some urban forest management and research needs, particularly if genus-level identification and DBH at coarse precision are acceptable. To promote greater consistency among field crews, we suggest techniques to encourage consistent population counts, using simpler methods for multi-stemmed trees, providing more resources for species identification, and more photo examples for other variables. Citizen science urban forest inventory and monitoring projects should use data validation and quality assurance procedures to enhance and document data quality.     

Estimating the stormwater attenuation benefits derived from planting four monoculture species of deciduous trees on vacant and underutilized urban land parcels

This paper presents research that was undertaken to determine whether planting deciduous trees, using intensive tree planting schemes, on vacant and underutilized urban land provides significant hydrologic benefits. This work contributes to an ongoing discussion on how to use vacant and underutilized land productively, and may be important to land use decision-makers, whose policies support the use of green infrastructure for stormwater management. Tree growth parameters for four monoculture planting schemes were modeled (all trees had a 50.8 mm caliper at planting) and included (i) 450 Ginkgo biloba, (ii) 92 Platanus × acerifolia, (iii) 120 Acer saccharinum, and (iv) 434 Liquidambar styraciflua, on a 1.6-acre parcel. i-Tree Hydro (formerly UFORE-Hydro) was used to derive a simplified Microsoft Excel-based water balance model to quantify the canopy interception potential and evaporation, based on 7 years (2002–2008) of historical hourly rainfall and mean temperature data in Hamilton, Ontario, Canada. This study revealed that three of the species responded similarly, while one species (L. styraciflua) performed significantly better with respect to total canopy storage potential and evaporation, capturing and evaporating 2.9 m³/tree over the 7 years analyzed, or 1280 m³ for the total tree stand of 434 trees. The analyses presented herein demonstrate that the tree canopy layer was able to intercept and evaporate approximately 6.5%–11% of the total rainfall that falls onto the crown across the 7 years studied, for the G. biloba, P. × acerifolia and A. saccharinum tree stands and 17%–27% for the L. styraciflua tree stand. This study revealed that the rate at which a species grows, the leaf area index of the species as it matures, and the total number of trees to be planted need to be determined to truly understand the behavior and potential benefits of different planting schemes; had the mature leaf area been used as the sole indicator of the stormwater attenuating potential for each species, the A. saccharinum would have been the selected species. Also, had attenuation and evaporation per unit of tree been the only measurement reported, the P. × acerifolia stand would have been deemed the best performing tree, attenuating and evaporating 8.1 m³/tree. While the actual values presented herein may be uncertain because of a lack of locally-derived tree growth models, the approach described warrants further investigation.     

Allometric equations for estimating the aboveground volume of five common urban street tree species in Daegu,Korea

Quantifying urban tree biomass and carbon (C) storage by using allometric equations is required for various studies such as assessing the inventory, modelling, and measuring ecosystem services of urban trees. However, the lack of urban-specific allometric equations leads to uncertainty when estimating urban tree biomass and C storage. Therefore, we followed a nondestructive approach and developed allometric equations specifically for Acer buergerianum Miq., Ginkgo biloba L., Platanus orientalis L., Prunus yedoensis Matsum., and Zelkova serrata (Thunb.) Makino in Daegu, Korea. Diameter at breast height (DBH)-based and DBH-and-height-based allometric equations were highly accurate at estimating the aboveground volume (R² > 0.92), while the allometric equations for P. orientalis and Z. serrata developed for traditional forests overestimated volume by 68% and 427%, respectively. The addition of a height variable into the DBH-based allometric equations did not increase the reliability of the allometric equations at a local level. The mean aboveground C storage of urban street trees was 24.9 Mg C/ha except for P. orientalis with a mean of 69.7 Mg C/ha, and the total aboveground C storage of urban street trees in Daegu was 10.6 Gg C. Alternatively, a generalized allometric equation which compiled species-specific equations can be applied for large-scale estimation. The generalized equations developed in this study and those found in the literature may suggest a constant value (～2.3–2.4) for the scaling exponent in the generalized equations. Allometric equations developed from natural or artificial stands may overestimate the volume of urban street trees; therefore, estimating urban tree biomass and C storage requires urban-specific allometric equations.     

Defect-disorder and risk assessment of heritage trees in urban Hong Kong

Heritage trees in a city, echoing factors conducive to outstanding performance, deserve special care and conservation. To understand their structural and health conditions in urban Hong Kong, 30 defect-disorder (DD) symptoms (physical and physiological) subsumed under four tree-position groups (soil-root, trunk, branching, and crown-foliage) and tree hazard rating were evaluated. The surveyed 352 trees included 70 species; 14 species with 233 trees were native. More trees had medium height (10–15 m), medium DBH (1–1.5 m) and large crown (>15 m). In ten habitats, public park and garden (PPG) accommodated the most trees, and roadside traffic island (RTI) and public housing estate (PH) had the least. Tree dimensions and tree habitats were significantly associated. The associations between the 2831 DD and tree-position groups, tree habitats and tree hazard rating were analyzed. Fourteen trees from Ficus microcarpa, Ficus virens and Gleditsia fera had high hazard rating, 179 trees from 22 species moderate rating, and 159 trees from 55 species low rating. RTI, roadside tree strip (RTS), roadside tree pit (RTP), roadside planter (RP) and stone wall (SW) had more moderate hazard rating, and PPG, roadside slope (RS) and government, institutional and community land (GIC) more low rating. Redundancy analysis showed that DD were positively correlated with RTS, RTP, RP and SW, but negatively correlated with PPG, RS and GIC (p < 0.05). The DD significantly increased tree hazard rating and failure potential. Future management implications for heritage-tree conservation and enhancement focusing squarely on critical tree defect-disorder in urban Hong Kong were explored, with application to other compact cities.     

Mapping of urban roadside trees – A case study in the tree register update process in Helsinki City

This case study describes a method for utilizing leaf-off airborne laser scanning (ALS) data for mapping characteristics of urban trees. ALS data were utilized to detect and update all street trees in the tree inventory of the City of Helsinki, Finland. The inventory consists of roughly 20,000 street trees with mean diameter at breast height (DBH) of 24 cm and mean height of 10.6 m. The large number of trees makes the manual updating process very laborious. The automatic mapping procedure presented in this paper detected 88.8% of all trees in the inventory. Tree height was predicted with root mean square error (RMSE) of 1.27 meters and tree DBH with RMSE of 6.9 cm. The presented method provides a practical and cost–effective tool for the mapping of urban tree characteristics. The cost–efficiency was further enhanced because the used ALS data were originally collected for other urban planning purposes.     

Enhancing plant diversity and mitigating BVOC emissions of urban green spaces through the introduction of ornamental tree species

Promoting the plant diversity of urban green spaces is crucial to increase ecosystem services in urban areas. While introducing ornamental plants can enhance the biodiversity of green spaces it risks environmental impacts such as increasing emissions of biogenic volatile organic compounds (BVOCs) that are harmful to air quality and human health. The present study, taking Qingdao City as a case study, evaluated the plant diversity and BVOC emissions of urban green spaces and tried to find out a solution to increase biodiversity while reducing BVOC emissions. Results showed that: (1) the species diversity and phylogenetic diversity of trees in urban green spaces were 22% and 16% lower than rural forest of this region; (2) urban areas had higher BVOC emission intensity (2.6 g C m⁻² yr⁻¹) than their rural surroundings (2.1 g C m⁻² yr⁻¹); (3) introducing the selected 11 tree species will increase 15% and 11% of species diversity and phylogenetic diversity, respectively; and (4) the BVOC emissions from green spaces will more than triple by 2050, but a moderate introduction of the selected low-emitting trees species could reduce 34% of these emissions. The scheme of introducing low-emitting ornamental species leads to a win–win situation and also has implications for the sustainable green space management of other cities.     

Estimation of broad-leaved canopy growth in the urban forested area using multi-temporal airborne LiDAR datasets

Inter-annual canopy growth is one of the key indicators for assessing forest conditions, but the measurements require laborious field surveys. Up-to-date LiDAR remote sensing provides sufficient three-dimensional morphological information of the ground to monitor canopy heights on a broad scale. Thus, we attempted to use multi-temporal airborne LiDAR datasets in the estimation of vertical canopy growth, across various types of broad-leaved trees in a large urban park.The growth of broad-leaved canopies in the EXPO '70 urban forest in Osaka, Japan was assessed with 19 plots at the stand level and 39 selected trees at the individual-tree level. Airborne LiDAR campaigns repeatedly observed the park in the summers of 2004, 2008, and 2010. We acquired canopy height models (CHMs) for each year from the height values of the uppermost laser returns at every 0.5 m grid. The annual canopy growth was calculated by the differences in CHMs and validated with the annual changes in field-measured basal areas and tree heights.LiDAR estimations revealed that the average annual canopy growth from 2004 to 2010 was 0.26 ± 0.11 m m⁻² yr⁻¹ at the plot level and 0.26 ± 0.10 m m⁻² yr⁻¹ at the individual-tree level. This result showed that growing trends were consistent at different scales through 2004 to 2010 despite uncertainty in estimating short-term growth for small crown areas at the individual-tree level. This LiDAR-estimated canopy growth shows a moderate relation to field-measured increase of basal areas and average heights. The estimation uncertainties seem to result from the complex canopy structure and irregular crown shape of broad-leaved trees. Challenges still remain on how to incorporate the growth of understory trees, growth in the lateral direction, and gap dynamics inside the canopy, particularly in applying multi-temporal LiDAR datasets to the large-scale growth assessment.     

The influence of increasing tree cover on mean radiant temperature across a mixed development suburb in Adelaide,Australia

The implementation of trees in urban environments can mitigate outdoor thermal stress. Growing global urban population and the risk of heatwaves, compounded by development driven urban warmth (the urban heat island), means more people are at risk of heat stress in our cities. Effective planning of urban environments must minimise heat-health risks through a variety of active and passive design measures at an affordable cost. Using the Solar and Longwave Environmental Irradiance Geometry (SOLWEIG) model and working within the bounds of current urban design, this study aimed to quantify changes in mean radiant temperature (T_mrt) from increased tree cover at five different 200 × 200 m urban forms (including compact mid-rise development, residential and open grassy areas) within a suburb of Adelaide, Australia during summer. Following a successful validation of SOLWEIG, street trees were strategically distributed throughout each of the five urban forms and the model run over five warm sunny days (13–17 February 2011). Results showed spatially averaged daytime (7:30–20:00) T_mrt reduced by between 1.7 °C and 5.1 °C at each site, while under peak heating conditions (16 February, 14:00) T_mrt reduced by between 2.0 °C and 7.1 °C. The largest reduction in T_mrt under peak warming conditions was at the residential site, despite having the fewest number of trees added. Directly below clusters of trees, T_mrt could be reduced by between 14.1 °C and 18.7 °C. SOLWEIG also highlighted that more built-up sites showed higher T_mrt under peak warming conditions due to increased radiation loading from 3D urban surfaces, but over the course of the day, open sites were exposed to greater and more uniform T_mrt. This study clearly demonstrates the capacity of street trees to mitigate outdoor thermal stress and provides guidance for urban planners on strategic street tree implementation.     

In situ emission of BVOCs by three urban woody species

Controlling and monitoring air quality in cities requires understanding anthropogenic sources, but also natural sources must be considered. This is because beneficial Biogenic Volatile Organic Compounds (BVOCs) can exacerbate air pollution by reacting with anthropogenic pollutants. Although these compounds help trees survive, they may have negative effect on human life in polluted cities. In this study we measured terpenoid emissions of urban trees early and late in the growing season, using Solid Phase Micro-extraction (SPME) in a branch enclosure system. Results showed that Robinia pseudoacacia and Platanus orientalis emitted significant amounts of isoprene throughout the season. Isoprene emission early in the season was roughly the same for both species. Late in the season, the standardized emission rate increased to 17.8 and 45 μg g⁻¹ dw h⁻¹ for R. pseudoacacia and P. orientalis, respectively. Furthermore, all trees emitted significant amounts of 2-ethylhexanol late in the season (7.3, 7.9, and 9.2 μg g⁻¹ dw h⁻¹ for Fraxinus rotundifolia, R. pseudoacacia, and P. orientalis, respectively). In conclusion, trees that are typically planted in urban Tehran, emit significant amounts of isoprene. Planting more F. rotundifolia and fewer P. orientalis trees would help improve air quality in Tehran and the cities like Tehran.     

Spatial distribution of saplings in heavily worn urban forests: Implications for regeneration and management

We studied the spatial distribution of saplings in the vicinity of other saplings and mature trees in heavily worn urban forests. Our aim was to identify favorable microsites for saplings to regenerate under different levels of wear. We hypothesized that these safe microsites were situated close to tree trunks that might offer shelter from trampling caused by humans and their pet dogs. The distribution of saplings was explored at 0.1–0.6 m to the nearest sapling and 0.1–2 m to the nearest mature tree. Sorbus aucuparia was the most abundant sapling species, followed by Populus tremula, Betula pubescens and Picea abies. These species all tended to cluster with their conspecific saplings and were generally randomly distributed with respect to mature trees. Saplings of S. aucuparia and P. tremula favored growing close to mature P. abies (already at 0.4–0.8 up to 2 m from the trunk base, respectively) and S. aucuparia trees (at 0.2–0.4 m up to 2 m). Betula sp. and Acer platanoides grew close to Pinus sylvestris trees. Furthermore, with increased levels of wear, saplings clustered more likely together and close to tree trunks. The results are contrary to the gap regeneration hypothesis known from rural unworn forests where saplings often grow in canopy gaps. We suggest the idea of a ‘sheltering group’, i.e. tree groups and thickets of densely growing conspecific saplings, for the maintenance of regeneration of saplings and other vegetation in heavily worn recreational forests. Since urban forestry may strongly affect the existence and spatial location of a high variety of microhabitats, small-scale spatial exploration is needed to identify microsites that offer opportunities for natural regeneration under heavy recreational use. To maintain natural regeneration and the survival of saplings in worn urban forests, we recommend microhabitat-level species-specific forest management.     

Long-term impact of road salt (NaCl) on soil and urban trees in Edmonton,Canada

The application of de-icing salts for winter road maintenance is recognized as a major contributor to the decline of urban trees. We conducted a long-term monitoring program across several locations in the City of Edmonton (Alberta, Canada) to evaluate the impact of roadway salt application on tree species widely planted in boulevards and right-of-ways: Ulmus americana, Fraxinus pennsylvanica, Pinus contorta, and Picea glauca. Soil and leaf samples were collected from a total of 16 sites over six years. There were four sites selected for each tree species: three mid- to high- traffic roadside sites that received regular winter maintenance and one non-serviced site (control). Sampling was performed three times per year from late spring to late summer. Airborne salinity was assessed in four locations at different distances from the road. In 50% of the roadside sites, soil electrical conductivity (EC) values exceeded 2 dS m⁻¹. Soil pH in all of the roadside sites was also significantly higher than in the control sites, with values ranging from 7.6 to 8.5. In all four species, trees growing in sites with high soil EC had increased leaf Na concentrations and reduced leaf chlorophyll concentrations. Among the airborne monitoring sites, Na deposition in high traffic locations was over four-fold higher than those measured in the control location. Furthermore, Na levels remained relatively high at 20–50 m from the main road. Our data suggest that while soil salinity is among the main stressors affecting roadside trees in Edmonton, salt spray deposition may also have a significant impact on trees located close to high vehicle traffic areas and dense road networks. Our study highlights the importance of collecting data over several years and from multiple locations to account for the spatial and temporal heterogeneity of the urban environments in order to better evaluate the impact of road salt application on urban trees.     

Tree and impervious cover change in U.S. cities

Paired aerial photographs were interpreted to assess recent changes in tree, impervious and other cover types in 20 U.S. cities as well as urban land within the conterminous United States. National results indicate that tree cover in urban areas of the United States is on the decline at a rate of about 7900 ha/yr or 4.0 million trees per year. Tree cover in 17 of the 20 analyzed cities had statistically significant declines in tree cover, while 16 cities had statistically significant increases in impervious cover. Only one city (Syracuse, NY) had a statistically significant increase in tree cover. City tree cover was reduced, on average, by about 0.27 percent/yr, while impervious surfaces increased at an average rate of about 0.31 percent/yr. As tree cover provides a simple means to assess the magnitude of the overall urban forest resource, monitoring of tree cover changes is important to understand how tree cover and various environmental benefits derived from the trees may be changing. Photo-interpretation of digital aerial images can provide a simple and timely means to assess urban tree cover change to help cities monitor progress in sustaining desired urban tree cover levels.