首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 640 毫秒
1.
The aim of this study was to understand the warp and weft directional tensile properties of the developed two dimensional (2D) multistitched multilayer E-glass/polyester woven nano composites. It was found that the warp and weft directional specific tensile strength and modulus of unstitched structure were higher than those of the machine stitched and machine stitched/nano structures due to stitching caused filament breakages. When the nano silica material in the unstitched E-glass/polyester composite structure increased, the warp and weft directional specific tensile strength and the modulus of the unstitched/nano structures increased. The failure of warp and weft directional 2D unstitched and unstitched/nano woven E-glass/polyester composite structures had a complete delamination in their cross-sections. But, the failure of warp and weft directional 2D stitched and stitched/nano woven E-glass/polyester composite structures had a local delamination in their cross-sections and the failure was confined at a narrow area. The warp and weft directional specific damaged areas of unstitched structure were higher than those of the stitched and stitched/nano structures. Also, the warp and weft directional specific damaged areas of machine stitched structure were slightly higher than those of the machine stitched/nano structure. It could be concluded that the addition of nano silica to the stitched structures improved to their damage resistance.  相似文献   

2.
The aim of this study was to understand the ±45 ° directional off-axis tensile properties of the developed two dimensional (2D) multistitched multilayer E-glass/polyester woven composites. It was found that the off-axis tensile strength of the unstitched structure was slightly higher than those of the multistitched structures. The reason was that the multistitching process caused the filament breakages. It was also found that when the stitching direction and stitching density in structures increased, their off-axis tensile modulus decreased. Therefore, stitching directions, stitching density and stitching yarn on the composite structures were considered as important parameters. All structures under the off-axis tensile load had normal deformation, or angular deformation or shrinkage in width. In addition, both the normal deformation and the shrinkages in width occurred in most of the two and four directional stitched structures. On the other hand, four directional Kevlar® 129 yarn dense stitched E-glass/polyester structure showed only shrinkage in width after angular deformation. This could be considered as a new failure mode because of the multistitching. These results indicated that the stitching directions and density generally influenced the off-axis tensile properties of the multistitched E-glass/polyester woven composites.  相似文献   

3.
In this study, multistitched woven nano composites were developed and their in-plane shear properties were characterized. The in-plane shear strength of unstitched structure was low compared to that of the unstitched/nano structures. However, the in-plane shear strength of unstitched structure was high compared to the machine stitched structures because of stitching and stitching yarn-matrix interfacial region. Additionally, the in-plane shear strength of machine stitched/nano composite structure was slightly high compared to the unstitched structure. The multistitched and multistitched/nano structures had limited delamination in their cross-sections. Their delamination regions were confined at a narrow area due to multistitching. This was considered that the developed multistitched/nano composites has better demage tolerance compared to unstitched composites.  相似文献   

4.
The aim of this study is to analyze and determine the off-axis tensile properties of air-entangled textured polyester fabrics based on unit cell interlacing frequency. For this purpose, continuous filament polyester air-entangled textured yarn was used to produce plain, ribs and satin woven fabrics. The fabrics were cut from the warp direction (0°) to weft direction (90°) at every 15° increment, and tensile tests were applied to those of the off-axis samples. The strength and elongation results were introduced to the statistical model developed, and regression analyses were carried out. Hence, the effects of off-axis loading and interlacement on the directional tensile properties of the fabric were investigated. The regression model showed that off-axis loading influences fabric tensile strength. On the other hand, interlacement frequency is the most important factor for fabric tensile elongation. The results from the regression model were compared with the measured values. This study confirmed that the method used in this study as can be a viable and reliable tool. Future research will concentrate on multiaxially directional fabric and the probability that it will result in homogeneous in-plane fabric properties.  相似文献   

5.
Enhancement of the mechanical and vibrational properties of glass/polyester composites was aimed via matrix modification technique. To achieve this, unsaturated polyester was modified by incorporation of oligomeric siloxane in the concentration range of 1–3 wt%. Modified matrix composites reinforced with woven roving glass fabric were compared with untreated glass/polyester in terms of mechanical and interlaminar properties by conducting tensile, flexure, and short-beam shear tests. It was found that after incorporation of 3 % oligomeric siloxane into the polyester matrix, the tensile, flexural, and interlaminar shear strength (ILSS) values of the resulting composite increased by 16, 15, and 75 %, respectively. The increases in ILSS as well as in tensile and flexural properties were considered to be an indication of better fiber/matrix interaction as confirmed by SEM fractography images. Furthermore, the effect of oligomeric siloxane incorporation on the vibrational properties of the composites was investigated by experimental modal testing and the natural frequencies of the composites were found to increase with increasing siloxane concentration.  相似文献   

6.
3D woven composites provide efficient delamination suppression, enhanced damage tolerance, superior impact, ballistic and blast performance characteristics over 2D fabric laminates. At the same time, this type of composites, having practically straight in-plane fibers, show significantly better in-plane stiffness and strength properties than respective properties of conventional composites. But, how the in-plane elastic and strength characteristics of this type of fabrics compare with respective in-plane properties of equivalent 2D woven fabrics. This paper presents a comprehensive experimental study of the comparison of in-plane tensile, bending, crimp interchange properties of UD, 2D, 3D orthogonal, 3D angle-interlock and 3D warp interlock multi-layer structures woven from E-glass tow. The results depict that the 3D woven fabrics have considerably superior mechanical properties with much lesser crimp compared to 2D fabrics.  相似文献   

7.
A commercially available polyester resin was reinforced with cabuya fibers. The experimental variables were the fiber loading and the length of the fiber. Tensile strength, flexural strength, and the Izod impact resistance were measured for the samples and compared to the polyester resin performance without reinforcement. Mechanical properties of the cabuya fiber reinforced material were also compared with the same resin but reinforced with glass fibers. An increase in fiber load decreases the tensile strength for the cabuya reinforced composite, where a value of 52.6 MPa corresponded to the tensile stress of the resin without reinforcement and a value of 34.5 MPa for the best reinforcement achieved with cabuya. An increase in both fiber load and length increases the Young’s modulus of the cabuya reinforced material, and a maximum value of 2885 MPa was obtained. The Young’s modulus and impact resistance values for the cabuya composite (2885 MPa and 100.87 J/m, respectively) reached higher values than those obtained for non-reinforced polyester material (2639 MPa and 5.82 J/m, respectively), and lower than the glass fiber composite (5526 MPa and 207.46 J/m, respectively); while the tensile and flexural strength obtained for the cabuya composite (34.5 MPa and 32.6 MPa, respectively) were lower than the unreinforced (52.6 MPa and 62.9 MPa, respectively) and glass fiber reinforced polyester (87.3 MPa and 155 MPa, respectively).  相似文献   

8.
The research on coir-polyester composites initiated the interest in the development of woven coir fiber-reinforced polyester composites. The mechanical properties of woven coir-polyester composites were evaluated as per ASTM standards and the machinability behavior was studied by conducting drilling tests in this investigation. The woven coir-polyester composites exhibited the average values of tensile, flexural and impact strength of 19.9 MPa, 31.3 MPa and 49.9 kJ/m2 respectively. The effect of NaOH treatment on the improvement of mechanical properties of woven coir-polyester composites were studied in this investigation. The 40 % increase of tensile strength, 42 % increase of flexural strength and 20 % increase of impact strength were achieved by treated woven coir fiber-reinforced polyester composites. The regression models for predicting thrust force, torque and tool wear in drilling of woven coir-polyester composites were developed and the effect of drilling parameters were analyzed.  相似文献   

9.
Glass woven fabric interlayered nonwovens composed of Nylon 6 staple fibers, recycled Kevlar fibers, and low-Tm polyester fibers are prepared into the glass-interlayer plank. Afterwards, their tensile strength, bursting strength, quasistatic and dynamic puncture resistances are evaluated by changing low-Tm polyester and Kevlar fibers mass fractions. The results show that when comprising 30 wt% of low-Tm polyester fibers and 20 wt% of Kevlar fibers, the composite plank yields the maximum tensile strength, bursting strength, quasi-static and dynamic puncture resistances. The double planks arranged in cross direction have higher quasi-static and dynamic puncture resistances than those oriented in parallel direction. According to stereoscope observations, the quasi-static and dynamic puncture resistances of glass-interlayer plank have different fracture mechanism for resisting against spike penetration. In addition, the bursting strength is proportional to quasistatic puncture resistance.  相似文献   

10.
This work aims to predict the mechanical properties of woven jute/banana hybrid composite. Woven fabrics are arranged in three layers of different sequence. Resin used in this work is Epoxy LY556 with hardener HY951. Composite specimen are prepared by hand-layup techniques. The effect of layering sequence on the mechanical properties namely tensile, flexural and impact was analysed. It is found that the tensile and flexural strength of hybrid composite (Banana/Jute/Banana) is higher than that of individual composites. Similarly, the impact strength of Jute/Banana/Jute hybrid composite is better than other types of composite. It is found that the moisture absorption of woven banana fiber composite is lesser than the hybrid composite. Fractography study of the fractured specimen is carried out using scanning electron microscope to analyse the fracture behaviour of the hybrid composite.  相似文献   

11.
This paper presents an investigation of the influences causing failure in the materials comprising polymer matrix composites. Structures with differences in stacking sequences and design configuration are analysed. The objective of this study is to investigate and evaluate the reasons for the failure of composite lamination structures in terms of stress, strength, strain, and Young modulus within a morphology observation of composite materials. The materials selected for the study were a chopped strand mat (CSM) and a woven roving (WR) fabric. These materials are used as reinforcement and are produced by the hand lay-up technique using epoxy and polyester matrix resin. The experiment was performed using specimens made of notched (open-hole; OH) tension and un-notched (UN) shapes. The characteristics of different shapes, materials, and lamination structures are studied in this research. The results showed the failure phenomenon in the structure of the polymer matrix composite is dependent on the characteristics of the material used and the design configuration of both structures.  相似文献   

12.
Tensile strength plays a vital role in determining the mechanical behavior of woven fabrics. In this study, two artificial neural networks have been designed to predict the warp and weft wise tensile strength of polyester cotton blended fabrics. Various process and material related parameters have been considered for selection of vital few input parameters that significantly affect fabric tensile strength. A total of 270 fabric samples are woven with varying constructions. Application of nonlinear modeling technique and appreciable volume of data sets for training, testing and validating both prediction models resulted in best fitting of data and minimization of prediction error. Sensitivity analysis has been carried out for both models to determine the contribution percentage of input parameters and evaluating the most impacting variable on fabric strength.  相似文献   

13.
This paper explains a study conducted to evaluate mechanical properties of woven structures of basalt. The mechanical properties like shear strength and tensile strength were studied. Tensile properties of basalt hybrid and non-hybrid fabrics are predicted by computational tool and verified with experimental data. The shear strength was investigated by using picture frame fixture. The tests were recorded by a CCD monochrome camera during displacement of specimen at various positions. The images were used for image analysis program developed in MATLAB. The results of image analysis were compared with the actual experimental results. The results illustrate that the mechanical properties of fabrics experience a marked improvement when hybridization of basalt with polyester and polypropylene in different sets of weaves takes place. These findings are important requirements for using such fabrics for high-tech applications and composite forming.  相似文献   

14.
This paper reports the fabrication of electrical heating elements based on the graphene/waterborne polyurethane (WPU) composite coated on polyester fabric with toughness like that of artificial leather. Samples were prepared with 0, 4, 8, and 16 wt% of graphene by using the knife edge method, and then, the samples were annealed from 100 oC to 160 °C. The graphene content had a large effect on the electrical and electrical heating properties. The surface resistivity was decreased by approximately 6 orders of magnitude with an increase from 0 wt% to 16 wt% graphene/WPU composite fabric. The electric heating properties were also improved, as indicated by the percolation threshold. Samples with various graphene contents were annealed, and it was found that the electrical and electrical heating properties were improved, and the most enhanced properties were obtained when the samples were annealed at 120 °C. The initial modulus and tensile strength were increased in comparison with those of 0 wt% and 16 wt% graphene/WPU composite coated on fabrics, but the elongation at break value was slightly decreased with an increasing graphene content. When the samples were annealed, initial modulus and tensile strength of samples were improved at 120 °C and 140 °C, and they were slightly decreased at 160 °C. However, the elongation at break showed an opposite tendency to the tensile strength. With the increase in content of graphene and annealing at 120 °C and 140 °C, the samples were more stiff and tough, and at 160 °C, the samples were softer. Therefore, graphene/WPU composite coated on polyester fabric by use of the annealing process may have applications in electrical heating elements due to its excellent heating performance and toughness like that of artificial leather.  相似文献   

15.
Woven Kenaf/Kevlar Hybrid Yarn is the combination of natural and synthetic fibers in the form of thread or yarn. The yarn is weaved to form a fabric type of fiber reinforced material. Then, the fabric is fabricated with epoxy as the resin to form a hybrid composite. For composite fabrication, woven fabric Kenaf/Kevlar hybrid yarn composite was prepared with vacuum bagging hand lay-up method. Woven fabric Kenaf/Kevlar hybrid yarn composite was fabricated with total fiber content of 40 % and 60 % of Epoxy as the matrix. The fiber ratios of Kenaf/Kevlar hybrid yarn were varied in weight fraction of 30/70, 50/50 and 70/30 respectively. The composites of woven fabric Kenaf/Epoxy and woven fabric Kevlar/Epoxy were also fabricated for comparison. The mechanical properties of five (5) samples composites were tested accordingly. Result has shown that of value of strength and modulus woven fabric Kenaf/Kevlar Hybrid Yarn composite was increased when the Kevlar fiber content increased. Therefore, among the hybrid composite samples result showed the woven fabric Kenaf/Kevlar Hybrid Yarn composites with the composition of 30/70 ratio has exhibited the highest energy absorption with 148.8 J which 28 % lower than Kevlar 100 % sample. The finding indicated there is a potential combination of natural fiber with synthetic fiber that can be fabricated as the composite material for the application of high performance product.  相似文献   

16.
In this paper, the bending properties of woven carbon/glass and carbon/aramid fabric-reinforced polymer laminates is studied using a combination of experimental analysis and fracture observation. Six types of each hybrid composite were manufactured by lamination of the carbon/aramid fabric and carbon/glass fabric using VARTM. Bending behaviors were fundamentally evaluated for the six types of monolithic composites laminated by the same fabric. The objective was to achieve a good bending strength by effective combination of composite structures using limited amounts of a raw material. It was shown that the bending property was different, depending on the type of fiber, lamination structure, and the number of layers.  相似文献   

17.
The aim of this study was to understand the failure mechanism of two dimensional dry fabric structure considering yarn sets and interlacements. For this purpose, data generated on air-entangled textured polyester woven fabric under the simple tensile load and analyzed by developed regression model. The regression model showed that warp and weft directional tensile strengths of satin fabric were higher than those of plain and rib fabrics in unravel sample. This might be related to the number of interlacements of the fabrics. There was not a considerable difference between warp directional tensile strength of ravel and unravel satin fabrics, whereas weft directional tensile strength of ravel satin fabric decreased rapidly with respect to its unravel form. The satin fabric showed the highest warp directional tensile strength among the others. The lowest weft directional tensile strength was received from ribs fabric. In semi-ravel sample, all fabrics showed low warp and weft directional tensile strength values except in plain fabric. Warp directional tensile elongation of plain fabric was the highest in unravel sample. Satin fabric showed the highest warp directional tensile elongation in the ravel sample. Warp directional tensile elongations of all the fabrics in the semi-ravel sample became low. Weft directional tensile elongation of satin fabric was the highest in unravel sample. In addition, satin and plain fabrics showed the highest weft directional tensile elongations in the ravel sample. Weft directional tensile elongations of all the fabrics in the semi-ravel sample became low except in ribs fabric.  相似文献   

18.
In this paper, the composite reinforced with three dimensional orthogonal woven fabric/epoxy resin was fabricated with vacuum assisted resin transfer model. The tensile behavior in 0° and 90° directions were experimentally executed. The tensile behavior of 3D orthogonal woven composite was numerical simulated based on the unit cell model and compared with the experimental result, the influence of crack damage and stress on fiber, resin and fiber/resin interface was analyzed. The maximum differences between experimental and simulated results are 3.23 % and 7.94 %. The verified model can be used to simulate the other static and dynamic mechanical properties and analyze the influence of the behavior of component material on the mechanical material properties of 3DOWC.  相似文献   

19.
The tensile properties of air-entangled textured polyester single and multiple yarn ends before and after weaving were analyzed. The effects of weaving process considering fabric unit cell interlacement and number of yarn ends were evaluated by regression model. For this purpose, plain, ribs and satin woven fabrics were produced. The yarns were raveled from fabrics, and the tensile tests were applied to these yarns. The developed regression model showed that the number of interlacement and crimp ratio on the warp and weft yarns influence their tensile strength. Tensile strength of raveled yarns decreased compared to that of the bobbin yarn due to the effect of weaving process. This property degradation on the ravel yarns considered process degradation. Generally, when the number of warp and weft yarn ends increases, the warp and weft yarn tensile strengths for each fabric type decrease, whereas the warp and weft yarn tensile elongations slightly increase. The results from regression model were compared with the measured values. This study confirmed that the method in the study can be a viable and reliable tool. The research finding could be useful those who work on preform fabrication.  相似文献   

20.
The co-woven-knitted (CWK) fabric and multi-layered biaxial weft-knitted (MBWK) fabric were produced using glass filaments as warp and weft inserted yarns and high tenacity polyester as stitched yarns. Vacuum Assisted Resin Transfer Molding process was used to produce the two composites. Tensile tests were carried out in the course, wale and slanting directions of the composites, respectively. Specific stress-strain curves and failure modes of the two composites were investigated and compared. Results reveal that tensile strengths and elastic moduli of the two composites in the course and wale directions are better than those in the bias direction. All the composite samples fracture in the brittle damage mode. Furthermore, the buckling due to different inserted ways of the warp and weft yarns has a few influences on the tensile properties of the two composites. This research may lay a foundation for the establishment of the process windows for the co-woven-knitted reinforced composites.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号