Effects of irrigation strategies and soils on field grown potatoes: Yield and water productivity

Yield and water productivity of potatoes grown in 4.32 m² lysimeters were measured in coarse sand, loamy sand, and sandy loam and imposed to full (FI), deficit (DI), and partial root-zone drying (PRD) irrigation strategies. PRD and DI as water-saving irrigation treatments received 65% of FI after tuber bulking and lasted for 6 weeks until final harvest. Analysis across the soil textures showed that fresh yields were not significant between the irrigation treatments. However, the same analysis across the irrigation treatments revealed that the effect of soil texture was significant on the fresh yield and loamy sand produced significantly higher fresh yield than the other two soils, probably because of higher leaf area index, higher photosynthesis rates, and “stay-green” effect late in the growing season. More analysis showed that there was a significant interaction between the irrigation treatments and soil textures that the highest fresh yield was obtained under FI in loamy sand. Furthermore, analysis across the soil textures showed that water productivities, WP (kg ha⁻¹ fresh tuber yield mm⁻¹ ET) were not significantly different between the irrigation treatments. However, across the irrigation treatments, the soil textures were significantly different. This showed that the interaction between irrigation treatments and soil textures was significant that the highest significant WP was obtained under DI in sandy loam. While PRD and DI treatments increased WP by, respectively, 11 and 5% in coarse sand and 28 and 36% in sandy loam relative to FI, they decreased WP in loamy sand by 15 and 13%. The reduced WP in loamy sand was due to nearly 28% fresh tuber yield loss in PRD and DI relative to FI even though ET was reduced by 9 and 11% in these irrigation treatments. This study showed that different soils will affect water-saving irrigation strategies that are worth knowing for suitable agricultural water management. So, under non-limited water resources conditions, loamy sand produces the highest yield under full irrigation but water-saving irrigations (PRD and DI) are not recommended due to considerable loss (28%) in yield. However, under restricted water resources, it is recommended to apply water-saving irrigations in sandy loam and coarse sand to achieve the highest water productivity.     

Irrigation of sunflower (Helianthus annuus) in relation to tillage and mulching

For sustainable sunflower production in semi-arid sub-tropical regions, it is essential to increase its water use efficiency. Field studies were conducted for three years on deep alluvial loamy sand (Typic Ustipsamment) and sandy loam (Typic Ustochrept) soils at Punjab Agricultural University, Ludhiana, India, to evaluate the interactive effects of three irrigation regimes (irrigation water to net open pan evaporation ratios, I₁, I₂, I₃) on sunflower yield in relation to tillage (conventional tillage, CT, and deep-tillage, DT) and mulching (no mulch, M₀, and residue mulch, M₁).Both deep tillage and mulch significantly increased crop yield irrespective of soil type and year. Increase in mean achene yield across soils during three years with DT over CT varied between 10 and 16% and that with mulch over no mulch by 8 to 17%.Deep tillage and/or mulching helped the crop in efficient utilization of water by increasing leaf area index (LAI) and the depth and density of rooting. Irrigation and tillage interacted for their effects on yield on loamy sand, as the crop responded to higher level of irrigation with CT than with DT. On loamy sand, mean achene yield increased with increase in water supply up to IW/PE = 1.5 in a dry year and upto IW/PE = 1.2 in relatively wetter years. On sandy loam, mean yield response to irrigations was observed upto IW/PE = 1.0 in all the three years.Regression analysis of relative yield against water supply during the three years on both the soils, showed that for 80% relative yield the crop required 105 cm water in CTM₀, 90 cm in CTM or DTM₀ and only 80 cm in DTM. The study suggests that deep tillage or straw mulch may be used to achieve higher water use efficiency in sunflower on coarse textured soils in semi-arid, sub-tropical regions.     

Effects of irrigation strategies and soils on field grown potatoes: Root distribution

Root distribution of field grown potatoes (cv. Folva) was studied in 4.32 m² lysimeters and subjected to full (FI), deficit (DI), and partial root-zone drying (PRD) irrigation strategies. Drip irrigation was applied for all irrigations. Irrigations were run in three different soils: coarse sand, loamy sand, and sandy loam. Irrigation treatments started after tuber bulking and lasted until final harvest with PRD and DI receiving 65% of FI. Potatoes irrigated with water-saving irrigation techniques (PRD and DI) did not show statistically different dry root mass and root length density (RLD, cm root per cm³ soil) compared with root development in fully irrigated (FI) potatoes. Highest RLD existed in the top 30-40 cm of the ridge below which it decreased sharply. The RLD was distributed homogenously along the ridge and furrow but heterogeneously across the ridge and furrow with highest root density in the furrow. Most roots accumulated in the surface layers of coarse sand as compared to the other soil types. In the deep soil profile (30-70 cm) a higher root density was found in loamy sand compared with the sandy loam and coarse sand. Approximately twice the amounts of roots were found below the furrows compared with the corresponding layers below the ridges. The RLD values in the soil profile of the ridges and the furrows followed the Gerwitz and Page model: RLD = α × exp(−β × z). The highest value of surface root density (α) and rate of change in density (β) was found in coarse sand while the lowest values of α and β were found in the sandy loam and loamy sand. The model estimated the effective rooting depth in coarse sand and sandy loam quite well but did slightly overestimate it in the loamy sand. Statistical analysis showed that one α and β value can be used for each soil irrespective of the irrigation treatment. Thus, the effective rooting depths corresponding to root length densities of 0.1 and 0.25 cm cm⁻³ for sandy loam, loamy sand, and coarse sand soils were 99, 141, and 94 cm, and 80, 115, and 78 cm, respectively, calculated from top of the ridge. The findings of this study can be used in practice for efficient use of water and nutrients in the field.     

Irrigation and tillage effects on root development,water use and yield of wheat on coarse textured soils

Summary Rapid drying of surface layers of coarse-textured soils early in the growth season increases soil strength and restricts root growth. This constraint on root growth may be countered by deep tillage and/or early irrigation. We investigated tillage and irrigation effects on root growth, water use, dry matter and grain yield of wheat on loamy sand and sandy loam soils for three years. Treatments included all combinations of two tillage systems i) conventional tillage (CT) — stirring the soil to 10 cm depth, ii) deep tillage (DT) — subsoiling with a single-tine chisel down to 35–40 cm, 40 cm apart followed by CT; and four irrigation regimes, i) I₀ — no post-seeding irrigation, ii) I₁ — 50 mm irrigation 30 days after seeding (DAS), iii) I₂ — 50 mm irrigation 30 DAS and subsequent irrigations of 75 mm each when net evaporation from USWB class A open pan (PAN-E) since previous irrigation accumulated to 82 mm, and iv) I₃ — same as in I² but irrigation applied when PAN-E accumulated to 62 mm. The crop of wheat (Triticum aestivum L. HD 2329) was fertilized with 20kg P, 10kg K and 5kg Zn ha^–1 at seeding. The rate of nitrogen fertilization was 60 kg ha^–1 in the unirrigated and 120 kg ha^–1 in the irrigated treatments. Tillage decreased soil strength and so did the early post-seeding irrigation. Both deep tillage and early irrigation shortened the time needed for the root system to reach a specified depth. Subsequent wetting through rain/irrigation reduced the rate of root penetration down the profile and also negated deep tillage effects on rooting depth. However, tillage/irrigation increased root length density in the rooted profile even in a wet year. Better rooting resulted in greater profile water depletion, more favourable plant water status and higher dry matter and grain yields. In a dry year, the wheat in the DT plots used 46 mm more water, remained 3.3 °C cooler at grain-fill and yielded 68% more grain than in CT when unirrigated and grown in the loamy sand. Early irrigation also increased profile water depletion, more so in CT than DT. Averaged over three years, grain yield in DT was 12 and 9% higher than in CT on loamy sand and sandy loam, respectively. Benefits of DT decreased with increase in rainfall and irrigation. Irrigation significantly increased grain yield on both soils, but the response was greatly influenced by soil type, tillage system and year. The study shows that soil related constraints on root growth may be alleviated through deep tillage and/or early irrigation.     

Comparison of drip and sprinkler irrigation strategies on sunflower seed and oil yield and quality under Mediterranean climatic conditions

This study compares the effects of different irrigation regimes on seed yield and oil yield quality and water productivity of sprinkler and drip irrigated sunflower (Helianthus annus L.) on silty-clay-loam soils in 2006 and 2007 in the Mediterranean region of Turkey. In sprinkler irrigation a line-source system was used in order to create gradually varying irrigation levels. Irrigation regimes consisted of full irrigation (I₁) and three deficit irrigation treatments (I₂, I₃ and I₄), and rain-fed treatment (I₅). In the drip system, irrigation regimes included full irrigation (FI-100), three deficit irrigation treatments (DI-25, DI-50, DI-75), partial root zone drying (PRD-50) and rain-fed treatment (RF). Irrigations were scheduled at weekly intervals both in sprinkler and drip irrigation, based on soil water depletion within a 0.90 m root zone in FI-100 and I₁ plots. Irrigation treatments influenced significantly (P < 0.01) sunflower seed and oil yields, and oil quality both with sprinkler and drip systems. Seed yields decreased with increasing water stress levels under drip and sprinkler irrigation in both experimental years. Seed yield response to irrigation varied considerably due to differences in soil water contents and spring rainfall distribution in the experimental years. Although PRD-50 received about 36% less irrigation water as compared to FI-100, sunflower yield was reduced by an average of 15%. PRD-50 produced greater seed and oil yields than DI-50 in the drip irrigation system. Yield reduction was mainly due to less number of seeds per head and lower seed mass. Soil water deficits significantly reduced crop evapotranspiration (ET), which mainly depends on irrigation amounts. Significant linear relationships (R² = 0.96) between ET and oil yield (Y) were obtained in each season. The seed yield response factors (ky_seed) were 1.24 and 0.86 for the sprinkler and 1.19 and 1.06 for the drip system in 2006 and 2007, respectively. The oil yield response factor (ky_oil) for sunflower was found to be 1.08 and 1.49 for both growing seasons for the sprinkler and 1.36 and 1.25 for the drip systems, respectively. Oil content decreased with decreasing irrigation amount. Consistently greater values of oil content were obtained from the full irrigation treatment plots. The saturated (palmitic and stearic acid) and unsaturated (oleic and linoleic acid) fatty acid contents were significantly affected by water stress. Water stress caused an increase in oleic acid with a decrease in linoleic acid contents. The palmitic and stearic acid concentrations decreased under drought conditions. Water productivity (WP) values were significantly affected by irrigation amounts and ranged from 0.40 to 0.71 kg m⁻³ in 2006, and from 0.69 to 0.91 kg m⁻³ in 2007. The PRD-50 treatment resulted in the greatest WP (1.0 kg m⁻³) and irrigation water productivity (IWP) (1.4 kg m⁻³) in both growing seasons. The results revealed that under water scarcity situation, PRD-50 in drip and I₂ in sprinkler system provide acceptable irrigation strategies to increase sunflower yield and quality.     

Effects of irrigation strategies and soils on field-grown potatoes: Gas exchange and xylem [ABA]

Gas exchange was measured in potatoes (cv. Folva) grown in lysimeters (4.32 m²) in coarse sand, loamy sand, and sandy loam and subjected to full (FI), deficit (DI), and partial root-zone drying (PRD) irrigation strategies. PRD and DI as water-saving irrigation treatments received 65% of FI and started after tuber bulking and lasted for six weeks until final harvest. Midday photosynthesis rate (A_n) and stomatal conductance (g_s) of fully irrigated (FI) plants were lowest in coarse sand and mean A_n of diurnal measurements in FI, PRD and DI tended to be lower in this soil as compared with the loamy sand and sandy loam. The results revealed that diurnal values of A_n and g_s in PRD and DI were consistently lower than FI without reaching significant differences in accordance with findings that xylem [ABA] in PRD was significantly higher than FI, and tended to be higher than in DI. Diurnal measurements showed that A_n reached peak values during mid-morning and midday, while g_s were highest during the morning. Intrinsic water use efficiency (A_n/g_s) correlated linearly well with the leaf to air vapor pressure deficit (VPD) and the slope of the line revealed the rate of A_n/g_s increase per each kPa increase in VPD, i.e. approximately 10 μmol mol⁻¹. Transpiration efficiency (A_n/T) of PRD was higher than DI, which shows slightly better efficient water use than DI. The slope of the linear relationship between transpiration efficiency and VPD decreased from −2.03 to −1.04 during the time course of the growing season, indicating the negative effect of leaf ageing on photosynthesis and thus on plant water use efficiency. This fact shows the possibility to save water during last growth stages through applying water-saving irrigations without much effect on transpiration efficiency.     

Performance evaluation and calibration of soil water content and potential sensors for agricultural soils in eastern Colorado

This study evaluated the performance of three soil water content sensors (CS616/625, Campbell Scientific, Inc., Logan, UT; TDT, Acclima, Inc., Meridian, ID; 5TE, Decagon Devices, Inc., Pullman, WA) and a soil water potential sensor (Watermark 200SS, Irrometer Company, Inc., Riverside, CA) in laboratory and field conditions. Soil water content/potential values measured by the sensors were compared with corresponding volumetric water content (θ_v, m³ m⁻³) values derived from gravimetric samples, ranging approximately from the permanent wilting point (PWP) to field capacity (FC) volumetric water contents. Under laboratory and field conditions, the factory-based calibrations of θ_v did not consistently achieve the required accuracy for any sensor in the sandy clay loam, loamy sand, and clay loam soils of eastern Colorado. Salt (calcium chloride dihydrate) added to the soils in the laboratory caused the CS616, TDT, and 5TE sensors to experience errors in their volumetric water content readings with increased bulk soil electrical conductivity (EC; dS m⁻¹). Results from field tests in sandy clay loam and loamy sand soils indicated that a linear calibration (equations provided) for the TDT, CS616 and 5TE sensors (and a logarithmic calibration for the Watermark sensors) could reduce the errors of the factory calibration of θ_v to less than 0.02 ± 0.035 m³ m⁻³. Furthermore, the performance evaluation tests confirmed that each individual sensor needed a unique calibration equation for every soil type and location in the field. In addition, the calibrated van Genuchten (1980) equation was as accurate as the calibrated logarithmic equation and can be used to convert soil water potential (kPa) to volumetric soil water content (m³ m⁻³). Finally, analysis of the θ_v field data indicated that the CS616, 5TE and Watermark sensor readings were influenced by diurnal fluctuations in soil temperature, while the TDT was not influenced. Therefore, it is recommended that the soil temperature be considered in the calibration process of the CS616, 5TE, and Watermark sensors. Further research will be aimed towards determining the need of sensor calibration for every agricultural season.     

Tillage and irrigation effects on crop yields and soil properties under the rice-wheat system in the Indian Himalayas

Conservation tillage systems generally improve soil organic C (SOC), plant available water capacity (PAWC), aggregation and soil water transmission. A field experiment was conducted for 4 years (2001-2002 to 2004-2005) to study tillage (conventional tillage (CT) and zero tillage (ZT)) systems. The selected irrigation treatments were at four levels (I₁: pre-sowing (PS), I₂: PS + active tillering (AT)/crown root initiation (CRI), I₃: PS + AT/CRI + panicle initiation (PI)/flowering (FL), and I₄: PS + AT/CRI + PI/FL + grain filling (GF)), applied at the critical growth stages on rice (Oryza sativa L.) and wheat (Triticum aestivum L.). Their effects on direct seeded rice productivity and soil properties (SOC and selected physical properties) after rice and wheat harvest were investigated. Soil organic C contents after rice and wheat harvest in the 0-15 cm soil depth were higher under ZT than under CT. Soil organic C increased significantly with I₂ over I₁ for both crops and with I₄ over I₂ for the wheat crop. The PAWC was significantly higher with ZT than CT. Zero tilled and frequently irrigated plots showed enhanced infiltration characteristics (infiltration rate, cumulative infiltration and sorptivity) and saturated hydraulic conductivity. Both direct seeded rice and wheat yields were not significantly different in the plots under ZT and CT. There was a significant increase in both rice and wheat yields in the plots under I₂ over I₁. However, water use efficiency between irrigation treatments was not significantly different. Hence, under direct seeded rice-wheat system in a sandy clay loam soil of the sub-temperate Indian Himalayas, farmers may adopt ZT with two irrigations in each crop for optimum resource conservation.     

Increasing water productivity of irrigated crops under limited water supply at field scale

Borkhar district is located in an arid to semi-arid region in Iran and regularly faces widespread drought. Given current water scarcity, the limited available water should be used as efficient and productive as possible. To explore on-farm strategies which result in higher economic gains and water productivity (WP), a physically based agrohydrological model, Soil Water Atmosphere Plant (SWAP), was calibrated and validated using intensive measured data at eight selected farmer fields (wheat, fodder maize, sunflower and sugar beet) in the Borkhar district, Iran during the agricultural year 2004-2005. The WP values for the main crops were computed using the SWAP simulated water balance components, i.e. transpiration T, evapotranspiration ET, irrigation I, and the marketable yield Y_M in terms in terms of Y_MT⁻¹, Y_M ET⁻¹ and Y_M I⁻¹.The average WP, expressed as $ T⁻¹ (US $ m⁻³) was 0.19 for wheat, 0.5 for fodder maize, 0.06 for sunflower and 0.38 for sugar beet. This indicated that fodder maize provides the highest economic benefit in the Borkhar irrigation district. Soil evaporation caused the average WP values, expressed as Y_M ET⁻¹ (kg m⁻³), to be significantly lower than the average WP, expressed as Y_MT⁻¹, i.e. about 27% for wheat, 11% for fodder maize, 12% for sunflower and 0.18 for sugar beet. Furthermore, due to percolation from root zone and stored moisture content in the root zone, the average WP values, expressed as Y_MI⁻¹ (kg m⁻³), had a 24-42% reduction as compared with WP, expressed as Y_M ET⁻¹.The results indicated that during the limited water supply period, on-farm strategies like deficit irrigation scheduling and reduction of the cultivated area can result in higher economic gains. Improved irrigation practices in terms of irrigation timing and amount, increased WP in terms of Y_MI⁻¹ (kg m⁻³) by a factor of 1.5 for wheat and maize, 1.3 for sunflower and 1.1 for sugar beet. Under water shortage conditions, reduction of the cultivated area yielded higher water productivity values as compared to deficit irrigation.     

Antecedent water content effects on runoff and sediment yields from two Coastal Plain Ultisols

The highly weathered, low-carbon, intensively cropped, drought-prone Coastal Plain soils of Georgia are susceptible to runoff and soil loss, especially at certain times of the year when soil water contents are elevated. We quantified the effects of antecedent water content (AWC) on runoff (R) and sediment (E) losses from two loamy sands managed under conventional- (CT), strip- (ST), and/or no-till (NT) systems. Two AWC treatments were evaluated: field moist (FM) and pre-wet (PW), created with and without post pesticide application irrigations (∼12 mm of water added with the rainfall simulated over 30 min) for incorporation. Treatments (5) evaluated were: CT + FM, CT + PW, ST + FM, ST + PW, and NT + PW. Field plots, each 2-m × -3 m, were established on each treatment. Each 6-m² field plot received simulated rainfall at a variable rainfall intensity (I_v) pattern for 70 min (site 1) or a constant rainfall intensity (I_c) pattern for 60 min (site 2; I_c = 50.8 mm h⁻¹). Adding ∼12 mm of water as herbicide incorporation increased AWCs of the 0-2 (3-9-fold) and 2-15 (23-117%) cm soil depths of PW plots compared to existing field moist soil conditions. Increase in AWC increased R (as much as 60%) and maximum R rates (as much as 62%), and decreased E (at least 59%) and maximum E rates (as much as 2.1-fold) for corresponding tillage treatments. Compared to CT plots, ST and NT plots decreased R (at least 2.6-fold) and maximum R rates (as much as 3-fold), and decreased E (at least 2.7-fold) and maximum E rates (at least 3.2-fold). Runoff curves for pre-wetted CT and ST plots were always higher than corresponding FM curves, whereas E curves for field moist CT and ST plots were always higher than corresponding PW curves. Changes in AWC and tillage affected detachment and transport processes controlling runoff and sediment yields. A more accurate measure of rainfall partitioning and detachment and transport processes affecting R and E losses was obtained when commonly occurring field conditions (increased AWC with irrigation; I_v pattern derived from natural rainfall; commonly used tillage systems) were created and evaluated.     

Effects of water infiltration and storage in cultivated soil on surface irrigation

Surface irrigation analysis and design require the knowledge of the variation of the cumulative infiltration water Z (L) (per unit area) into the soil as a function of the infiltration time t (T). The purpose of this study is to evaluate water infiltration and storage under surface irrigation in an alluvial clay soil cultivated with grape yield, and to determine if partially wetted furrow irrigation has more efficient water storage and infiltration than traditional border irrigation. The two irrigation components considered were wet (WT) and dry (DT) treatments, at which water applied when available soil water reached 65% and 50%, and the traditional border irrigation control. Empirical power form equations were obtained for measured advance and recession times along the furrow length during the irrigation stages of advance, storage, depletion and recession. The infiltration (cumulative depth, Z and rate, I) was functioned to opportunity time (t_o) in minute for WT and DT treatments as: Z_WT = 0.528 t_o^0.6, Z_DT = 1.2 t_o^0.501, I_WT = 19 t_o^−0.4, and I_DT = 36 t_o^−0.498. The irrigation efficiency and soil water distribution have been evaluated using linear distribution and relative schedule depth. Coefficient of variation (CV) was 5.2 and 9.5% for WT and DT under furrow irrigation system comparing with 7.8% in border, respectively. Water was deeply percolated as 11.88 and 19.2% for wet and dry furrow treatments, respectively, compared with 12.8% for control, with no deficit in the irrigated area. Partially wetted furrow irrigation had greater water-efficiency and grape yield than both dry furrow and traditional border irrigations, where application efficiency achieved as 88.1% for wet furrow irrigation that achieved high grape fruit yield (30.71 Mg/ha) and water use efficiency 11.9 kg/m³.     

Effects of deficit irrigation on the yield and yield components of drip irrigated cotton in a mediterranean environment

A field study on cotton (Gossypium hirsutum L., cv.) was carried out from 2005 to 2008 in the Çukurova Region, Eastern Mediterranean, Turkey. Treatments were designated as I₁₀₀ full irrigation; DI₇₀, DI₅₀ and DI₀₀ which received 70, 50, and 0% of the irrigation water amount applied in the I₁₀₀ treatment. The irrigation water amount to be applied to the plots was calculated using cumulative pan evaporation that occurred during the irrigation intervals. The effect of water deficit or water stress on crop yield and some plant growth parameters such as yield response, water use efficiencies, dry matter yield (DM), leaf area index (LAI) as well as on lint quality components was evaluated. The average seasonal evapotranspiration ranged from 287 ± 15 (DI₀₀) to 584 ± 80 mm (I₁₀₀). Deficit irrigation significantly affected crop yield and all yield components considered in this study. The average seed cotton yield varied from 1369 ± 197 (DI₀₀) to 3397 ± 508 kg ha⁻¹ (I₁₀₀). The average water use efficiency (WUE_ET) ranged from 6.0 ± 1.6 (I₁₀₀) to 4.8 ± 0.9 kg ha⁻¹ mm⁻¹ (DI₀₀), while average irrigation water use efficiency (WUE_I) was between 9.4 ± 3.0 (I₁₀₀) and 14.4 ± 4.8 kg ha⁻¹ mm⁻¹ (DI₅₀). Deficit irrigation increased the harvest index (HI) values from 0.26 ± 0.054 (I₁₀₀) to 0.32 ± 0.052 kg kg⁻¹ (DI₅₀). Yield response factor (Ky) was determined to be 0.98 based on four-year average. Leaf area index (LAI) and dry matter yields (DM) increased with increasing water use. This study demonstrated that the full irrigated treatment (I₁₀₀) should be used for semiarid conditions with no water shortage. However, DI₇₀ treatment needs to be considered as a viable alternative for the development of reduced irrigation strategies in semiarid regions where irrigation water supplies are limited.     

Yield and quality of melon grown under different irrigation and nitrogen rates

During 2 years, a melon crop (Cucumis melo L. cv. Sancho) was grown under field conditions to investigate the effects of different nitrogen (N) and irrigation (I) levels on fruit yield, fruit quality, irrigation water use efficiency (IWUE) and nitrogen applied efficiency (NAE). The statistical design was a split-plot with four replications, where irrigation was the main factor of variation and N was the secondary factor. In 2005, irrigation treatments consisted of applying daily a moderate water stress equivalent to 75% of ETc (crop evapotranspiration), a 100% ETc control and an excess irrigation of 125% ETc (designated as I₇₅, I₁₀₀ and I₁₂₅), while the N treatments were 30, 85, 112 and 139 kg N ha⁻¹ (designated as N₃₀, N₈₅, N₁₁₂ and N₁₃₉). In 2006, both the irrigation and N treatments applied were: 60, 100 and 140% ETc (I₆₀, I₁₀₀ and I₁₄₀) and 93, 243 and 393 kg N ha⁻¹ (N₉₃, N₂₄₃ and N₃₉₃). Moderate water stress did not reduce melon yield and high IWUE was obtained. Under severe deficit irrigation, the yield was reduced by 22% mainly due to decrease fruit weight. The relative yield (yield/maximum yield) was higher than 95% when the irrigation depth applied was in the range of 87-136% ETc. In 2006, the interaction between irrigation and N was significant for yield, fruit weight and IWUE. The best yield, 41.3 Mg ha⁻¹, was obtained with 100% ETc at N₉₃. The flesh firmness and the placenta and seeds weight increased when the irrigation level was reduced by 60% ETc. The highest NAE was obtained with quantities of water close to 100% ETc and increased as the N level was reduced. The highest IWUE was obtained with applications close to 90 kg N ha⁻¹. The I₂₄₃ and I₃₉₃ treatments produced inferior fruits due to higher skin ratios and lower flesh ratios. These results suggest that it is possible to apply moderate deficit irrigation, around 90% ETc, and reduce nitrogen input to 90 kg ha⁻¹ without lessening quality and yields.     

Forage quality, water use and nitrogen utilization efficiencies of pearl millet (Pennisetum americanum L.) grown under different soil moisture and nitrogen levels

The increasing scarcity of water for irrigation is becoming the most important problem for producing forage in all arid and semi-arid regions. Pearl millet is a key crop in these regions which needs relatively less water than other crops. In this research, a field study was conducted to identify the best combination of irrigation and nitrogen (N) management to achieve acceptable pearl millet forage both in quantity and quality aspects. Pearl millet was subjected to four irrigation treatments with interaction of N fertilizer (0, 75, 150 and 225 kg ha⁻¹). The irrigation treatments were 40%, 60%, 80% and 100% of total available soil water (I₄₀, I₆₀, I₈₀ and I₁₀₀, respectively). The results showed that increasing moisture stress (from I₄₀ to I₁₀₀) resulted in progressively less total dry matter (TDM), leaf area index (LAI), and nitrogen utilization efficiency (NUzE), while water use efficiency (WUE) and the percentage of crude protein (CP%) increased. The highest TDM and LAI were found to be 21.45 t ha⁻¹ and 8.65, in I₄₀ treatment, respectively. TDM, WUE, CP% and profit responses to N rates were positive. The maximum WUE of 4.19 kg DM/m³ was achieved at I₁₀₀ with 150 kg N ha⁻¹. The results of this research indicate that the maximum profit of forage production was obtained in plots which were fully irrigated (I₄₀) and received 225 kg N ha⁻¹. However, in the situation which water is often limited and not available, application of 150 kg N ha⁻¹ can produce high forage quality and guaranty acceptable benefits for farmers.     

Improved water capture and erosion reduction through furrow diking

Crop production in Georgia and the Southeastern U.S. can be limited by water; thus, supplemental irrigation is often needed to sustain profitable crop production. Increased water capture would efficiently improve water use and reduce irrigation amounts and other input costs, thus improving producer's profit margin. We quantified water capturing and erosional characteristics of furrow diking by comparing runoff (R) and soil loss (E) from furrow diked (DT) and non-furrow diked tilled (CT) systems. A field study (Faceville loamy sand, Typic Kandiudult) was established (2006 and 2007) near Dawson, GA with DT and CT systems managed to irrigated cotton (Gossypium hirsutum L.). Treatments included: DT vs. CT; DT with and without shank (+/− S); and rainfall simulation performed (0, 60 days after tillage, DAT). Simulated rainfall (50 mm h⁻¹ for 1 h) was applied to all 2 m × 3 m plots (n = 3). All runoff and E were measured from each flat, level sloping 6-m² plot (slope = 1%). Compared to CT, DT decreased R and E by 14-28% and 2.0-2.8 times, respectively. Compared to DT − S, DT + S decreased R and E by 17-56% and 26% to 2.1 times, respectively. Compared to sealed/crusted soil conditions at 60 DAT, simulating rainfall on a freshly tilled seedbed condition (DAT = 0) decreased R by 69% to 3.4 times and increased E by 27%. DT0 + S + RF0 plots (best-case scenario) had 2.8 times less R, and 2.6 times less E than CT − S + RF60 plots (worst-case). Based on $1.17 ha-mm⁻¹ to pump irrigation water and $18.50 ha⁻¹ for DT, a producer in the Coastal Plain region of Georgia would recover cost of DT by saving the first 16 ha-mm of water. The DT + S system is a cost-effective management practice for producers in Georgia and the Southeastern U.S. that positively impacts natural resource conservation, producer profit margins, and environmental quality.     

Drip irrigation of tea (Camellia sinensis L.): 1. Yield and crop water productivity responses to irrigation

The effects of drip irrigation on the yield and crop water productivity responses of four tea (Camellia sinensis (L.) O. Kuntze) clones were studied four consecutive years (2003/2004-2006/2007), in a large (9 ha) field experiment comprising of six drip irrigation treatments (labelled: I₁-I₆) and four clones (TRFCA PC81, AHP S15/10, BBK35 and BBT207) planted at a spacing of 1.20 m × 0.60 m at Kibena Tea Limited (KTL), Njombe in the Southern Tanzania in a situation of limited water availability. Each clone × drip irrigation treatment combination was replicated six times in a completely randomized design with 144 net plots each with an area of 72 m². Clone TRFCA PC81 gave the highest yields (range: 5920-6850 kg dried tea ha⁻¹) followed by clones BBT207 (5010-5940 kg dried tea ha⁻¹), AHP S15/10 (4230-5450 kg dried tea ha⁻¹) and BBK35 (3410-4390 kg dried tea ha⁻¹) and drip irrigation treatment I₂ gave the highest yields, ranging from 4954 to 6072 kg dried tea ha⁻¹) compared with those from other treatments (4113-5868 kg dried tea ha⁻¹). Most of these yields exceeded those (4200 kg dried tea ha⁻¹) obtained from overhead sprinkler irrigation system in Mufindi also Southern Tanzania, and Kibena Estate itself. Results showed that drip irrigation of tea not only increased yields but also gave water saving benefits of up to 50% from application of 50% less water to remove the cumulative soil water deficit (treatment I₂), and with labour saving of 85% for irrigation. The yield of dried tea per mm depth of water applied, i.e., “the crop water productivity” for drip irrigation of clones TRFCA PC81, BBT207 and BBK35, in 2003/2004 for instance, were 9.3, 8.5 and 7.1 kg dried tea [ha mm]⁻¹, respectively. The corresponding values in 2004/2005 were 2.7, 4.5 and 2.0 kg dried tea [ha mm]⁻¹ while the yield responses from clone AHP S15/10 were linear decreasing by 1 and 1.6 kg dried tea [ha mm]⁻¹ in 2003/2004 and 2004/2005, respectively. In 2005/2006 the crop water productivity from clones TRFCA PC81, AHP S15/10, BBK35 and BBT207 were 4.5, 0.4, 5.2 and 6.9 kg dried tea [ha mm]⁻¹, respectively with quadratic yield response functions to drip irrigation depth of water application. The results are presented and recommendations and implications made for technology-transfer scaling-up for increased use by large and smallholder tea growers.     

Impact of soil water stress on Nigellone oil content of black cumin seeds grown in calcareous-gypsifereous soils

Nigellone (dithymoquinone) is the main active constituent of volatile oil of black cumin (Nigella sativa) seeds. It is presently used in traditional medicines, for culinary as ornamentals, and is also considered for its abundant nectar secretion. While black cumin, investigated recently (for the oil, essential oil, and other biologically active constituents of their seeds) the effects of deficit irrigation on seeds Nigellone content produced on gypsifereous soils are not known. Randomized complete block design experiments were conducted with three replications and four irrigation treatments on soils with five different gypsum contents over two growing seasons (2008-2009 and 2009-2010). These experiments aim to monitor and quantify water stress and Nigellone volatile oil content of black cumin as a function of crop water stress index and soil gypsum content. The soil gypsum content treatments were 60.0 (G₁), 137.6 (G₂), 275.2 (G₃), 314.2 (G₄) and 486.0 (G₅) g kg⁻¹. Three irrigation treatments were based on replenishing the 0.60 m deep root zone to field capacity when the maximum allowable depletion (MAD) of the available soil water holding capacity of 25% (I₁), 50% (I₂) and 75% (I₃) were maintained in the crop experiments. A dryland treatment (fully stressed, I₄) was also included. The lower (non-stressed) and upper (stressed) baselines were measured to calculate crop water stress index. The crop water stress index behaved as expected, dropping to near zero following an irrigation and increasing gradually as black cumin plants depleted soil water reserves. The seasonal mean values of crop water stress index for the irrigation treatments; I₁, I₂, and I₃ were increased from 0.189, 0.287, 0.380 to 0.239, 0.366, 0.467, respectively when the soil gypsum content increased from 60.0 to 486.0 g kg⁻¹. The highest Nigellone volatile oil content of black cumin seeds was obtained for G₁I₁ treatment (5.1 g kg⁻¹) while the lowest content (3.5 g kg⁻¹) was obtained for G₅I₁ treatment. Equations that can be used to predict the Nigellone volatile oil content of black cumin seeds were developed for the three irrigation schedules of different maximum allowable depletion of available soil water holding capacity using the relationships between the Nigellone volatile oil content and the seasonal mean crop water stress index for different soil gypsum contents. The relationships between black cumin seed yield, Nigellone volatile oil content and seasonal mean crop water stress index values were primarily linear. These relations can be used to predict the yield of black cumin seeds, seeds Nigellone volatile oil content, and irrigation timing in soils with different soil gypsum contents. Thus, the obtained data will be beneficial for further research.     

Irrigation planning in cotton through simulation modeling

Experiments were undertaken at CCS Haryana Agricultural University Farm, Sirsa (India) to estimate the optimum irrigation schedule for cotton resulting in minimum percolation losses. The sprinkler line source technique was adopted for creating various irrigation regimes at different crop growth stages. The SWASALT (Simulation of Water And SALT) model after calibration and validation provided water balance components. The wa-ter management response indicators (WMRI's) such as transpiration efficiency E_t/(Irr + P), relative transpiration E_t/E_tp, evapotranspiration efficiency ET/(Irr + P), soil moisture storage change ΔW/W_int (deficit/excess) and percolation loss Perc/(Irr. + P) were evaluated using water balance components as estimated by the simulation study. Under limited water supply conditions, the optimum irrigation depth was found to be 57 mm at crop growth stages with pre-sowing and 1^st irrigation of 120 mm and 80 mm respectively for sandy clay loam underlain by sandy loam soil (Type I). The corresponding values of relative transpiration, transpiration efficiency and evapotranspiration efficiency were 0.65, 0.65 and 0.89 respectively. The crop yield varied linearly with increasing irrigation depth which was evident from increase in relative transpiration with increasing depth of water application. However, increased depth of irrigation resulted in less moisture utilisation from soil storage (20% depletion at 40 mm depth and 4.4% moisture built up at 100 mm depth). The extended simulation study for sandy soil underlain by loamy sand (Type II) indicated that two pre-sowing irrigations each 40 mm and subsequent irrigations of 40 mm at an interval of 20 days depending upon rainfall were optimum. This irrigation scenario resulted in zero percolation loss accompanied by 74% relative transpiration and 14 per cent soil moisture depletion. Received: 20 November 1995     

In-season wheat root growth and soil water extraction in the Mediterranean environment of northern Syria

Wheat is the most important cereal crop in the semi-arid eastern Mediterranean region that includes northern Syria. Knowledge of wheat root depth and the vertical distribution during the winter growing season is needed for sound scheduling of irrigation and efficient use of water. This article reports evaluation of root development for three winter-grown bread (Triticum aestivum L.) and durum (Triticum turgidum L.) wheat under four soil water regimes (rainfed and full irrigation with two intermediate levels of 33 and 66% of full irrigation). Roots were sampled by soil coring to a depth of 0.75 m at four occasions during 2005-2006 growing season. Two distinct phases of root development were identified, a rapid downward penetration from emergence to end tillering phase, followed by a substantial root mass growth along the profile from tillering to mid-stem-elongation phase. Roots were detected as deep as 0.75 m during the initial rapid penetration, yet only 29% of the total seasonal root mass was developed. This downward penetration rate averaged 7 mm d⁻¹ and produced 10.8 kg ha⁻¹ d⁻¹ of root dry-biomass. The bulging of root mass from tillering to mid-stem-elongation coincided with vigorous shoot growth, doubling root dry-biomass at a rate of 52 kg ha⁻¹ d⁻¹, compared to the seasonal root growth rate of 18.3 kg ha⁻¹ d⁻¹. A second-degree equation described the total root dry-biomass as a function of days after emergence (r² = 0.85), whereas a simpler equation predicted it as a function of cumulative growing degree days (r² = 0.85). The final grain yield was a strong function of irrigation regimes, varying from 3.0 to 6.5 t ha⁻¹, but showed no correlation with root biomass which remained similar as soil water regimes changed. This observation must be viewed with care as it lacks statistical evidence. Results showed 90% of root mass at first irrigation (15 April) confined in the top 0.60-0.75 m soil in bread wheat. Presence of shallow restricting soil layers limited root depth of durum wheat to 0.45 m, yet total seasonal root mass and grain yield were comparable with non-restricted bread wheat. Most root growth occurred during the cool rainy season and prior to the late irrigation season. The root sampling is short of rigorous, but results complement the limited field data in literature collectively suggesting that irrigation following the rainy season may best be scheduled assuming a well developed root zone as deep as the effective soil depth within the top meter of soil.     

Tomato nitrogen accumulation and fertilizer use efficiency on a sandy soil, as affected by nitrogen rate and irrigation scheduling

Tomato production systems in Florida are typically intensively managed with high inputs of fertilizer and irrigation and on sandy soils with low inherent water and nutrient retention capacities; potential nutrient leaching losses undermine the sustainability of such systems. The objectives of this 3-year field study were to evaluate the interaction between N-fertilizer rates and irrigation scheduling on crop N and P accumulation, N-fertilizer use efficiency (NUE) and NO₃-N leaching of tomato cultivated in a plastic mulched/drip irrigated production system in sandy soils. Experimental treatments were a factorial combination of three irrigation scheduling regimes and three N-rates (176, 220, and 330 kg ha⁻¹). Irrigation treatments included were: (1) surface drip irrigation (SUR) both the irrigation and fertigation line placed underneath the plastic mulch; (2) subsurface drip irrigation (SDI) where the irrigation drip was placed 0.15 m below the fertigation line which was located on top of the bed; and (3) TIME (conventional control) with the irrigation and fertigation lines placed as in SUR and irrigation applied once a day. Except for the TIME treatment all irrigation treatments were soil moisture sensor (SMS)-based with irrigation occurring at 10% volumetric water content. Five irrigation windows were scheduled daily and events were bypassed if the soil water content exceeded the established threshold. The use of SMS-based irrigation systems significantly reduced irrigation water use, volume percolated, and nitrate leaching. Based on soil electrical conductivity (EC) readings, there was no interaction between irrigation and N-rate treatments on the movement of fertilizer solutes. Total plant N accumulation for SUR and SDI was 12-37% higher than TIME. Plant P accumulation was not affected by either irrigation or N-rate treatments. The nitrogen use efficiency for SUR and SDI was on the order of 37-45%, 56-61%, and 61-68% for 2005, 2006 and 2007, respectively and significantly higher than for the conventional control system (TIME). Moreover, at the intermediate N-rate SUR and SDI systems reduced NO₃-N leaching to 5 and 35 kg ha⁻¹, while at the highest N-rate corresponding values were 7 and 56 kg N ha⁻¹. Use of N application rates above 220 kg ha⁻¹ did not result in fruit and/or shoot biomass nor N accumulation benefits, but substantially increased NO₃-N leaching for the control treatment, as detected by EC monitoring and by the lysimeters. It is concluded that appropriate use of SDI and/or sensor-based irrigation systems can sustain high yields while reducing irrigation application as well as reducing NO₃-N leaching in low water holding capacity soils.