Furrow diking in conservation tillage

Crop production in the Southeastern U.S. can be limited by water; thus, supplemental irrigation is needed to sustain profitable crop production. Increased water capture would efficiently improve water use and reduce supplemental irrigation amounts/costs, thus improving producer's profit margin. We quantified infiltration (INF), runoff (R), and sediment (E) losses from furrow diked (+DT) and non-furrow diked (−DT) tilled conventional (CT) and strip tillage (ST) systems. In 2008, a field study (Tifton loamy sand, Typic Kandiudult) was established with DT, ST, and CT systems. In 2009, a field study (Faceville loamy sand, Typic Kandiudult) was established with DT and ST systems. Treatments (6) included: CT − DT, CT + DT, ST₁ (1-year old) − DT, ST₁ + DT, ST₁₀ (10-year old) − DT, and ST₁₀ + DT. Simulated rainfall (50 mm h⁻¹ for 1 h) was applied to each 2-m × 3-m plots (n = 3). Runoff and E were measured from each 6-m² plot. ST₁ + DT plots had 80-88% less R than ST₁ − DT plots. Any disturbance associated with DT in ST₁ systems did not negatively impact E values. For both soils, CT − DT plots represented the worst-case scenario in terms of measured R and E; ST + DT plots represented the best-case scenario. Trends for R, E, and estimated plant available water (PAW) values decreased in order of CT − DT, CT + DT, ST₁ − DT, ST₁ + DT, ST₁₀ − DT, and ST₁₀ + DT treatments. From a hydrology standpoint, ST₁ − DT plots behaved more similarly to CT plots than to other ST plots; from a sediment standpoint, ST₁ − DT plots behaved more similarly to other ST plots than to CT plots. DT had no effect on ST₁₀ plots. CT − DT and ST₁₀ + DT plots resulted in 5.9 (worst-case) and 8.1 (best-case) days of water for crop use, a difference of 2.2 days of water for crop use or 37%. Compared to the CT − DT treatment, an agricultural field managed to CT + DT, ST₁ − DT, ST₁ + DT, ST₁₀ − DT, and ST₁₀ + DT would save a producer farming the CT − DT field $5.30, $9.42, $13.55, $14.14, and $14.14 ha⁻¹, respectively, to pump the amount of water lost to R and not saved as INF back onto the field. The most water/cost savings occurred for CT and ST₁ plots as a result of DT. Savings for CT + DT, ST₁ − DT, and ST₁ + DT treatments represent 27%, 47%, and 68% of the cost of DT ($20 ha⁻¹) and 37%, 67%, and 96% of the savings a producer would have if managing the field to ST for 10 years without DT (ST₁₀ − DT) in a single 50-mm rainfall event. For row-crop producers in the Southeastern U.S. with runoff producing rainfall events during the crop growing season, DT is a management practice that is cost-effective from a natural resource and financial standpoint for those producers that continue to use CT systems and especially those that have recently adopted ST systems into their farming operations.     

Tillage and irrigation effects on crop yields and soil properties under the rice-wheat system in the Indian Himalayas

Conservation tillage systems generally improve soil organic C (SOC), plant available water capacity (PAWC), aggregation and soil water transmission. A field experiment was conducted for 4 years (2001-2002 to 2004-2005) to study tillage (conventional tillage (CT) and zero tillage (ZT)) systems. The selected irrigation treatments were at four levels (I₁: pre-sowing (PS), I₂: PS + active tillering (AT)/crown root initiation (CRI), I₃: PS + AT/CRI + panicle initiation (PI)/flowering (FL), and I₄: PS + AT/CRI + PI/FL + grain filling (GF)), applied at the critical growth stages on rice (Oryza sativa L.) and wheat (Triticum aestivum L.). Their effects on direct seeded rice productivity and soil properties (SOC and selected physical properties) after rice and wheat harvest were investigated. Soil organic C contents after rice and wheat harvest in the 0-15 cm soil depth were higher under ZT than under CT. Soil organic C increased significantly with I₂ over I₁ for both crops and with I₄ over I₂ for the wheat crop. The PAWC was significantly higher with ZT than CT. Zero tilled and frequently irrigated plots showed enhanced infiltration characteristics (infiltration rate, cumulative infiltration and sorptivity) and saturated hydraulic conductivity. Both direct seeded rice and wheat yields were not significantly different in the plots under ZT and CT. There was a significant increase in both rice and wheat yields in the plots under I₂ over I₁. However, water use efficiency between irrigation treatments was not significantly different. Hence, under direct seeded rice-wheat system in a sandy clay loam soil of the sub-temperate Indian Himalayas, farmers may adopt ZT with two irrigations in each crop for optimum resource conservation.     

Improved water capture and erosion reduction through furrow diking

Crop production in Georgia and the Southeastern U.S. can be limited by water; thus, supplemental irrigation is often needed to sustain profitable crop production. Increased water capture would efficiently improve water use and reduce irrigation amounts and other input costs, thus improving producer's profit margin. We quantified water capturing and erosional characteristics of furrow diking by comparing runoff (R) and soil loss (E) from furrow diked (DT) and non-furrow diked tilled (CT) systems. A field study (Faceville loamy sand, Typic Kandiudult) was established (2006 and 2007) near Dawson, GA with DT and CT systems managed to irrigated cotton (Gossypium hirsutum L.). Treatments included: DT vs. CT; DT with and without shank (+/− S); and rainfall simulation performed (0, 60 days after tillage, DAT). Simulated rainfall (50 mm h⁻¹ for 1 h) was applied to all 2 m × 3 m plots (n = 3). All runoff and E were measured from each flat, level sloping 6-m² plot (slope = 1%). Compared to CT, DT decreased R and E by 14-28% and 2.0-2.8 times, respectively. Compared to DT − S, DT + S decreased R and E by 17-56% and 26% to 2.1 times, respectively. Compared to sealed/crusted soil conditions at 60 DAT, simulating rainfall on a freshly tilled seedbed condition (DAT = 0) decreased R by 69% to 3.4 times and increased E by 27%. DT0 + S + RF0 plots (best-case scenario) had 2.8 times less R, and 2.6 times less E than CT − S + RF60 plots (worst-case). Based on $1.17 ha-mm⁻¹ to pump irrigation water and $18.50 ha⁻¹ for DT, a producer in the Coastal Plain region of Georgia would recover cost of DT by saving the first 16 ha-mm of water. The DT + S system is a cost-effective management practice for producers in Georgia and the Southeastern U.S. that positively impacts natural resource conservation, producer profit margins, and environmental quality.     

Irrigation, tillage and mulching effects on soybean yield and water productivity in relation to soil texture

Depleting groundwater resources in Indian Punjab call for diversifying from rice to crops with low evapo-transpiration needs and adopting water-saving technologies. Soybean offers a diversification option in coarse- to medium-textured soils. However, its productivity in these soils is constrained by high soil mechanical resistance and high soil temperature during early part of the growing season. These constraints can be alleviated through irrigation, deep tillage and straw mulching. This 3-years field study examines the individual and combined effects of irrigation, deep tillage, and straw mulching regimes on soybean yield and water productivity (WP) in relation to soil texture. Combinations of two irrigation regimes viz., full irrigation (I_f), and partial irrigation (I_p) in the main plot; two tillage regimes viz., conventional-till (CT)-soil stirring to 0.10 m depth, and deep tillage (DT)-chiseling down to 0.35 m depth followed by CT in the subplot; and two mulch rates viz., 0 (M₀) and 6 t ha⁻¹ (M) in the sub-subplot on two soils differing in available water capacity were evaluated.Seed yield was greater in the sandy loam than in the loamy sand reflecting the effects of available water capacity. Irrigation effects were greater on loamy sand (40%) than on sandy loam (5%) soil. Deep tillage benefits were also more on loamy sand (14%) compared to sandy loam (5%) soil. Yield gains with mulching were comparable on the two soils (19%). An evaluation of interaction effects showed that mulching response was slightly more in I_p (20%) than in I_f regimes (17%) in the sandy loam; while in the loamy sand, mulching gains were comparable (18-19%) in both irrigation regimes. Benefits of deep tillage in the loamy sand soil were more in I_p (20%) than in I_f regimes (17%). Deep tillage and straw mulching enhanced WP (ratio of seed yield/water use) from 1.39 to 1.97 kg ha⁻¹ mm⁻¹ in I_p regime, and from 1.87 to 2.33 kg ha⁻¹ mm⁻¹ in I_f regime in the loamy sand soil. These effects on WP were less in the sandy loam soil with greater available water capacity. Yield and WP gains are ascribed to deeper and denser rooting due to moderation of soil temperature and water conservation with straw mulching and tillage-induced reduction in soil mechanical resistance. Root mass in CTM₀, CTM, DTM₀ and DTM was 2.79, 5.88, 5.34 and 5.58 mg cm⁻² at pod-filling in the loamy sand soil. Comparable yield responses to deep tillage or mulching in the loamy sand soil suggest that either of the options, depending on their cost and availability considerations, can be employed for improving soybean yield and water productivity.     

Effects of conservation tillage practices on winter wheat water-use efficiency and crop yield on the Loess Plateau,China

In the semi-humid to arid loess plateau areas of North China, water is the limiting factor for rain-fed crop yields. Conservation tillage has been proposed to improve soil and water conservation in these areas. From 1999 to 2005, we conducted a field experiment on winter wheat (Triticum aestivum L.) to investigate the effects of conservation tillage on soil water conservation, crop yield, and water-use efficiency. The field experiment was conducted using reduced tillage (RT), no tillage with mulching (NT), subsoil tillage with mulching (ST), and conventional tillage (CT). NT and ST improved water conversation, with the average soil water storage in 0–200 cm soil depth over the six years increased 25.24 mm at the end of summer fallow periods, whereas RT soil water storage decreased 12 mm, compared to CT. At wheat planting times, the available soil water on NT and ST plots was significantly higher than those using CT and RT. The winter wheat yields were also significantly affected by the tillage methods. The average winter wheat yields over 6 years on NT or ST plots were significantly higher than that in CT or RT plots. CT and RT yields did not vary significantly between them. In each study year, NT and ST water-use efficiency (WUE) was higher than that of CT and RT. In the dry growing seasons of 1999–2000, 2004–2005 and the low-rainfall fallow season of 2002, the WUE of NT and ST was significantly higher than that of CT and RT, but did not vary significantly in the other years. For all years, CT and RT showed no WUE advantage. In relation to CT, the economic benefit of RT, NT, and ST increased 62, 1754, and 1467 yuan ha⁻¹, respectively, and the output/input ratio of conservation tillage was higher than that of CT. The overall results showed that NT and ST are the optimum tillage systems for increasing water storage and wheat yields, enhancing WUE and saving energy on the Loess Plateau.     

Comparison of drip and sprinkler irrigation strategies on sunflower seed and oil yield and quality under Mediterranean climatic conditions

This study compares the effects of different irrigation regimes on seed yield and oil yield quality and water productivity of sprinkler and drip irrigated sunflower (Helianthus annus L.) on silty-clay-loam soils in 2006 and 2007 in the Mediterranean region of Turkey. In sprinkler irrigation a line-source system was used in order to create gradually varying irrigation levels. Irrigation regimes consisted of full irrigation (I₁) and three deficit irrigation treatments (I₂, I₃ and I₄), and rain-fed treatment (I₅). In the drip system, irrigation regimes included full irrigation (FI-100), three deficit irrigation treatments (DI-25, DI-50, DI-75), partial root zone drying (PRD-50) and rain-fed treatment (RF). Irrigations were scheduled at weekly intervals both in sprinkler and drip irrigation, based on soil water depletion within a 0.90 m root zone in FI-100 and I₁ plots. Irrigation treatments influenced significantly (P < 0.01) sunflower seed and oil yields, and oil quality both with sprinkler and drip systems. Seed yields decreased with increasing water stress levels under drip and sprinkler irrigation in both experimental years. Seed yield response to irrigation varied considerably due to differences in soil water contents and spring rainfall distribution in the experimental years. Although PRD-50 received about 36% less irrigation water as compared to FI-100, sunflower yield was reduced by an average of 15%. PRD-50 produced greater seed and oil yields than DI-50 in the drip irrigation system. Yield reduction was mainly due to less number of seeds per head and lower seed mass. Soil water deficits significantly reduced crop evapotranspiration (ET), which mainly depends on irrigation amounts. Significant linear relationships (R² = 0.96) between ET and oil yield (Y) were obtained in each season. The seed yield response factors (ky_seed) were 1.24 and 0.86 for the sprinkler and 1.19 and 1.06 for the drip system in 2006 and 2007, respectively. The oil yield response factor (ky_oil) for sunflower was found to be 1.08 and 1.49 for both growing seasons for the sprinkler and 1.36 and 1.25 for the drip systems, respectively. Oil content decreased with decreasing irrigation amount. Consistently greater values of oil content were obtained from the full irrigation treatment plots. The saturated (palmitic and stearic acid) and unsaturated (oleic and linoleic acid) fatty acid contents were significantly affected by water stress. Water stress caused an increase in oleic acid with a decrease in linoleic acid contents. The palmitic and stearic acid concentrations decreased under drought conditions. Water productivity (WP) values were significantly affected by irrigation amounts and ranged from 0.40 to 0.71 kg m⁻³ in 2006, and from 0.69 to 0.91 kg m⁻³ in 2007. The PRD-50 treatment resulted in the greatest WP (1.0 kg m⁻³) and irrigation water productivity (IWP) (1.4 kg m⁻³) in both growing seasons. The results revealed that under water scarcity situation, PRD-50 in drip and I₂ in sprinkler system provide acceptable irrigation strategies to increase sunflower yield and quality.     

A method for spatial prediction of daily soil water status for precise irrigation scheduling

Available water holding capacity (AWC) and field capacity (FC) maps have been produced using regression models of high resolution apparent electrical conductivity (EC_a) data against AWC (adj. R² = 0.76) and FC (adj. R² = 0.77). A daily time step has been added to field capacity maps to spatially predict soil water status on any day using data obtained from a wireless soil moisture sensing network which transmitted hourly logged data from embedded time domain transmission (TDT) sensors in EC_a-defined management zones. In addition, regular time domain reflectometry (TDR) monitoring of 50 positions in the study area was used to assess spatial variability within each zone and overall temporal stability of soil moisture patterns. Spatial variability of soil moisture within each zone at any one time was significant (coefficient of variation [% CV] of volumetric soil moisture content (θ) = 3-16%), while temporal stability of this pattern was moderate to strong (bivariate correlation, R = 0.52-0.95), suggesting an intrinsic soil and topographic control. Therefore, predictive ability of this method for spatial characterisation of soil water status, at this site, was limited by the ability of the sensor network to account for the spatial variability of the soil moisture pattern within each zone. Significant variability of soil moisture within each EC_a-defined zone is thought to be due to the variable nature of the young alluvial soils at this site, as well as micro-topographic effects on water movement, such as low-lying ponding areas. In summary, this paper develops a method for predicting daily soil water status in EC_a-defined zones; digital information available for uploading to a software-controlled automated variable rate irrigation system with the aim of improved water use efficiency. Accuracy of prediction is determined by the extent to which spatial variability is predicted within as well as between EC_a-defined zones.     

Canopy temperature based system effectively schedules and controls center pivot irrigation of cotton

Cotton is a perennial plant with an indeterminate growth pattern that is typically produced like an annual, but requires proper management to effectively produce high yields and good fiber quality in a thermally limited environment like the northern Texas High Plains. In 2007 and 2008, we investigated the effect of irrigation scheduling/control method and amount on cotton (Gossypium hirsutum L.) yield and water use efficiency. Methods were automatic irrigation scheduling and control of a center pivot system, and manually scheduled irrigation to replenish soil-water to field capacity. Cotton was irrigated with LEPA (low energy, precision application) drag socks in furrow dikes; three blocks were irrigated manually and three were irrigated automatically. Six replicates of the manual and automatic irrigation treatments were included in the randomized block design. Manual irrigations were based on the weekly replenishment of soil-water to field capacity in the top 1.5 m of the soil profile and included a fully irrigated treatment (I₁₀₀), and treatments receiving 67% (I₆₇) and 33% (I₃₃) of the I₁₀₀ amount, plus a non-irrigated treatment (I₀). Automatic irrigations were triggered using a time temperature threshold (TTT) algorithm, which was designated as the I₁₀₀ treatment, and treatments receiving 67%, 33%, and 0% of that amount (I₆₇, I₃₃ and I₀, respectively). In 2007, overall mean lint yields (102.3 and 101.6 g m⁻², manual and automatic, respectively) were not significantly different. Similarly, yields were not significantly different across automatic and manual treatments in the same treatment level, with the exception of the I₆₇ treatment where the manual treatment yields were 11% greater. In 2008, the mean yields were 70% less than those in 2007 for both methods of irrigation (30.3 and 30.9 g m⁻², manual and automatic, respectively) due to harsh climatic conditions at emergence and heavy rainfall and cooler temperatures in the month of August. Yields from the automatically irrigated plots in the I₁₀₀ and I₆₇ treatments, however, were significantly greater than yields from the corresponding manually irrigated plots; though there was no significant difference between yields in the drier treatments (I₃₃ and I₀) plots. These results indicate that the TTT algorithm is a promising method for auto-irrigation scheduling of short season cotton in an arid region. However, further studies are essential to demonstrate consistent positive outcomes.     

Quantifying rainfall-runoff relationships on the Dera Calcic Fluvic Regosol ecotope in Ethiopia

Droughts, resulting in low crop yields, are common in the semi-arid areas of Ethiopia and adversely influence the well-being of many people. The objective of this study was to assess the benefit that in-field rainwater harvesting (IRWH) would have, compared to conventional tillage, on maize yields on a semi-arid ecotope at Dera situated on the eastern part of the Rift Valley. Rainfall-runoff measurements were made during 2003 and 2004 on 2 m × 2 m plots provided with a runoff measuring system and replicated three times for each treatment. There were two treatments: conventional tillage (CT) and no-till (NT), the latter with a flat surface that promotes runoff and therefore IRWH. Rainfall intensity was measured at 1 min intervals with an automatic tipping bucket instrument, and runoff was measured after each rain event. Measured runoff as a function of rainfall intensity and duration from half the rainfall-runoff events was used to determine the critical parameters of a appropriate runoff model. The calibrated model was found to be capable of predicting runoff in a satisfactory way.Rainfall-runoff measurements were made during the rain seasons in 2003 and 2004 during which there were 25 rain events with >9 mm of rain. There was no statistical difference between the runoff on the two treatments. The measured runoff (R) for the two rain seasons, expressed as a fraction of the rainfall during the measuring period (P), i.e. R/P, gave values of 0.46 and 0.39 for the NT and CT treatments, respectively.Results from 7 years of field experiments with IRWH at Glen in South Africa were used to estimate the yield benefit of NT for Dera compared to CT. The results were 696 and 494 kg ha⁻¹ for 2003 and 2004, respectively. Based on the estimated average long-term maize yield of 2000 kg ha⁻¹ at Dera, this was an estimated yield increase ranging from 25% to 35%.     

Rainfall concentration for increasing corn production under semiarid climate

The ridge and furrow farming of rainfall concentration (RC) system is being promoted to increase water availability to crops for improving and stabilizing agricultural production in the semiarid Loess region of northwest China. In the system, plastic-covered ridges serve as rainfall harvesting zones and furrows serve as planting zones. In recent years, however, the current RC practices are still confined to rural family units for very limited supplemental irrigation purposes. To adopt this system for large-scale use in the semiarid region and bring it into full play, it is necessary to test the befitting rainfall range for RC farming. A field study (using corn as an indicator crop) combined with rainfall simulation was designed to determine the effects of RC practices on soil water content, crop yield and water use efficiency (WUE) under three rainfall levels (230 mm, 340 mm and 440 mm) during the growing seasons of 2006 and 2007. The results indicated that with the rainfalls ranging within 230-440 mm, RC system can increase soil water content in 0-100 cm and temperature conditions in the topsoil (0-10 cm) in furrows by 5-12% and 0.7-1 °C, respectively. The corn seedlings emerged 1-2 days earlier, the developmental stages generally occurred earlier, and the plant height and total dry matter all significantly increased (P < 0.05). In 2006, compared to conventional flat (CF) practice, the grain yield and WUE in the RC system increased by 75.4% and 73.3%, respectively at 230 mm rainfall, and by 36.7% and 40.2%, respectively at 340 mm rainfall, but there was no significant difference between the RC₄₄₀ and CF₄₄₀ patterns. In 2007, the grain yield and WUE were 82.8% and 77.4%, respectively higher in the RC₂₃₀ plots than in the CF₂₃₀ plots, 43.4% and 43.1%, respectively higher in the RC₃₄₀ plots than in the CF₃₄₀ plots, and 11.2% and 9.5%, respectively higher in the RC₄₄₀ plots than in the CF₄₄₀ plots. Combining yield and WUE, it could be concluded that the optimal rainfall upper limit for RC system is below 440 mm rainfall in the experiment. In the case of corn, the adoption of RC practice in the 230-440-mm rainfall area will make the system more attractive during the whole growth period and offer a sound opportunity for sustainable farming under semiarid climate.     

Effects of winter wheat row spacing on evapotranpsiration, grain yield and water use efficiency

A field study was conducted from 2002 to 2007 to investigate the influence of row spacing of winter wheat (Triticum aestivum L.) on soil evaporation (E), evapotranspiration (ET), grain production and water use efficiency (WUE) in the North China Plain. The experiment had four row spacing treatments, 7.5 cm, 15 cm, 22.5 cm, and 30 cm, with plots randomly arranged in four replicates. Soil E was measured by micro-lysimeters in three seasons and ET was calculated from measurements of soil profile water depletion, irrigation, and rainfall. The results showed that E increased with row spacing. Compared with the 30-cm row spacing (average E = 112 mm), the reduction in seasonal E averaged 9 mm, 25 mm, and 26 mm for 22.5 cm, 15 cm, and 7.5 cm row spacings, respectively. Crop transpiration (T) increased as row spacing decreased. The seasonal rainfall interception and seasonal ET were relatively unchanged among the treatments. In three out of five seasons, the four different treatments showed similar grain yield, yield components and WUE. We conclude that for winter wheat production in the North China Plain, narrow row spacing reduced soil evaporation, but had minor improvements on grain production and WUE under irrigated conditions with adequate nutrient levels.     

Suspended sediment load prediction of river systems: An artificial neural network approach

Information on suspended sediment load is crucial to water management and environmental protection. Suspended sediment loads for three major rivers (Mississippi, Missouri and Rio Grande) in USA are estimated using artificial neural network (ANN) modeling approach. A multilayer perceptron (MLP) ANN with an error back propagation algorithm, using historical daily and weekly hydroclimatological data (precipitation P_(t), current discharge Q_(t), antecedent discharge Q_(t−1), and antecedent sediment load SL_(t−1)), is used to predict the suspended sediment load SL_(t) at the selected monitoring stations. Performance of ANN was evaluated using different combinations of input data sets, length of record for training, and temporal resolution (daily and weekly data). Results from ANN model were compared with results from multiple linear regressions (MLR), multiple non-linear regression (MNLR) and Autoregressive integrated moving average (ARIMA) using correlation coefficient (R), mean absolute percent error (MAPE) and model efficiency (E). Comparison of training period length was also made (4, 3 and 2 years of training and 1, 2 and 3 years of testing, respectively). The model efficiency (E) and R² values were slightly higher for the 4 years of training and 1 year of testing (4 * 1) for Mississippi River, indifferent for Missouri and slightly lower for Rio Grande River. Daily simulations using Input 1 (P_(t), Q_(t), Q_(t−1), SL_(t−1)) and three years of training and two years of testing (3 * 2) performed better (R² and E of 0.85 and 0.72, respectively) than the simulation with two years of training and three years of testing (2 * 3) (R² and E of 0.64 and 0.46, respectively). ANN predicted daily values using Input 1 and 3 * 2 architecture for Missouri (R² = 0.97) and Mississippi (R² = 0.96) were better than those of Rio Grande (R² = 0.65). Daily predictions were better compared to weekly predictions for all three rivers due to higher correlation within daily than weekly data. ANN predictions for most simulations were superior compared to predictions using MLR, MNLR and ARIMA. The modeling approach presented in this paper can be potentially used to reduce the frequency of costly operations for sediment measurement where hydrological data is readily available.     

Effects of deficit irrigation on the yield and yield components of drip irrigated cotton in a mediterranean environment

A field study on cotton (Gossypium hirsutum L., cv.) was carried out from 2005 to 2008 in the Çukurova Region, Eastern Mediterranean, Turkey. Treatments were designated as I₁₀₀ full irrigation; DI₇₀, DI₅₀ and DI₀₀ which received 70, 50, and 0% of the irrigation water amount applied in the I₁₀₀ treatment. The irrigation water amount to be applied to the plots was calculated using cumulative pan evaporation that occurred during the irrigation intervals. The effect of water deficit or water stress on crop yield and some plant growth parameters such as yield response, water use efficiencies, dry matter yield (DM), leaf area index (LAI) as well as on lint quality components was evaluated. The average seasonal evapotranspiration ranged from 287 ± 15 (DI₀₀) to 584 ± 80 mm (I₁₀₀). Deficit irrigation significantly affected crop yield and all yield components considered in this study. The average seed cotton yield varied from 1369 ± 197 (DI₀₀) to 3397 ± 508 kg ha⁻¹ (I₁₀₀). The average water use efficiency (WUE_ET) ranged from 6.0 ± 1.6 (I₁₀₀) to 4.8 ± 0.9 kg ha⁻¹ mm⁻¹ (DI₀₀), while average irrigation water use efficiency (WUE_I) was between 9.4 ± 3.0 (I₁₀₀) and 14.4 ± 4.8 kg ha⁻¹ mm⁻¹ (DI₅₀). Deficit irrigation increased the harvest index (HI) values from 0.26 ± 0.054 (I₁₀₀) to 0.32 ± 0.052 kg kg⁻¹ (DI₅₀). Yield response factor (Ky) was determined to be 0.98 based on four-year average. Leaf area index (LAI) and dry matter yields (DM) increased with increasing water use. This study demonstrated that the full irrigated treatment (I₁₀₀) should be used for semiarid conditions with no water shortage. However, DI₇₀ treatment needs to be considered as a viable alternative for the development of reduced irrigation strategies in semiarid regions where irrigation water supplies are limited.     

Impact of modified tillage on runoff and nutrient loads from potato fields in Prince Edward Island

Potato production accounts for ∼24% of the cultivated land-use in Prince Edward Island, Canada. The island often experiences prolonged dry periods interspersed with excessive rainfall events throughout the growing season. Thus, water retention is important for maximum crop production while sediment and nutrient loading to surface water systems are also concerns. Therefore, agronomic practices that reduce the environmental impact of potato production are being sought. Basin tillage (BT) is a potential option in which small dams are created in the furrows (row middles), resulting in basins that enhance infiltration, reduce runoff, minimize contaminant loads, and increase yields.This on-farm study compared BT against two types of ‘conventional’ hilling treatments with replicated plots on four field sites over two growing seasons. Field sites had sandy loam soils with topography slopes ranging from 3% to 5%. Within each field, nine 25 m long and 3.66 m wide (4 rows) plots were established, including three plots of each hilling treatment (CT = conventional tillage; RS = row shaper tillage; BT = basin tillage). Runoff volume, nutrient (phosphate, ammonium, nitrate) and suspended solids loads were measured using collection barrels on the down slope end of each furrow.Basin tillage had 78% and 75% less runoff than CT and RS, respectively (P < 0.05). Runoff differences between BT and CT were significant at all sites while runoff differences between BT and RS were significant at three of four sites. Reductions for each parameter (on a mass basis) averaged across all sites were: sediment 89%, nitrate 45%, ammonium 38%, and phosphate 15%; although, treatment effect was not significant for some mass loads in some fields. No significant effect on marketable potato yield was observed at any site; soil water was not limiting in either growing season. Overall, basin tillage was effective at reducing runoff and nutrient losses without affecting yield and appears to be an effective tool for decreasing environmental risks.     

Evaluation of the DRAINMOD-N II model for predicting nitrogen losses in a loamy sand under cultivation in south-east Sweden

The DRAINMOD-N II model (version 6.0) was evaluated for a cold region in south-east Sweden. The model was field-tested using four periods between 2002 and 2004 of climate, soil, hydrology and water quality data from three experimental plots, planted to a winter wheat-sugarbeet-barley-barley crop rotation and managed using conventional and controlled drainage. DRAINMOD-N II was calibrated using data from a conventional drainage plot, while data sets from two controlled drainage plots were used for model validation. The model was statistically evaluated by comparing simulated and measured drain flows and nitrate-nitrogen (NO₃-N) losses in subsurface drains. Soil mineral nitrogen (N) content was used to evaluate simulated N dynamics. Observed and predicted NO₃-N losses in subsurface drains were in satisfactory agreement. The mean absolute error (MAE) in predicting NO₃-N drainage losses was 0.16 kg N ha⁻¹ for the calibration plot and 0.21 and 0.30 kg N ha⁻¹ for the two validation plots. For the simulation period, the modelling efficiency (E) was 0.89 for the calibration plot and 0.49 and 0.55 for the validation plots. The overall index of agreement (d) was 0.98 for the calibration plot and 0.79 and 0.80 for the validation plots. These results show that DRAINMOD-N II is applicable for predicting NO₃-N losses from drained soil under cold conditions in south-east Sweden.     

Soil water dynamics and water use efficiency in spring maize (Zea mays L.) fields subjected to different water management practices on the Loess Plateau, China

Soil water supply is the main limiting factor to crop production across the Loess Plateau, China. A 2-year field experiment was conducted at the Changwu agro-ecosystem research station to evaluate various water management practices for achieving favorable grain yield (GY) with high water use efficiency (WUE) of spring maize (Zea mays L.). Four practices were examined: a rain-fed (RF) system as the control; supplementary irrigation (SI); film mulching (FM); and straw mulching (SM) (in 2008 only). The soil profile water storage (W) and the crop evapotranspiration (ET) levels were studied during the maize growing season, and the GY as well as the WUE were also compared. The results showed that mean soil water storage in the top 200 cm of the profile was significantly (P < 0.05) increased in the SI (380 mm in 2007, 411 mm in 2008) and SM (414 mm in 2008) compared to the FM (361 mm in 2007, 381 mm in 2008) and RF (360 mm in 2007, 384 mm in 2008) treatments. The soil water content was lower at the end of growing season than before planting in the 60-140 cm part of the profile in both the RF and FM treatments. Cumulative ET and average crop coefficiency (K_c) throughout the whole maize growing season were significantly (P < 0.05) higher in the SI (ET, 501 mm in 2007, 431 mm in 2008; K_c, 1.0 in 2007, 0.9 in 2008) treatment than in the other treatments. Both FM and SI significantly improved the GY. The WUE were increased significantly (23-25%; P < 0.05) under the FM treatment. It was concluded that both SI and FM are beneficial for improving the yield of spring maize on the Loess Plateau. However, FM is preferable because of the shortage of available water in the area.     

Effects of different emitter space and water stress on yield and quality of processing tomato under semi-arid climate conditions

The objective of the study was to determine the effects of different emitter spaces and water stress on crop yield, such that the tomatoes would be suitable for processing and paste output (Lycopersicon esculentum Mill cv. Shasta). Such variables were also analyzed with respect to crop quality characteristics (e.g., mean fruit weight - MFW, fruit diameter - FD, penetration value of fruit - PV, pH, total soluble solids - TSS, and ascorbic acid contents - AA). The experiment was conducted under ecological conditions typical of the Konya Plain, a semi-arid climate, in 2004 and 2005. Drip irrigation laterals were arranged in such a way that every row had one lateral. Emitters were spaced at 25, 50, and 75 cm intervals in the main plots, while four levels of water supply, irrigation at 7-day intervals with enough water to fill the soil depth of 0-60 cm until capacity was reached (I₁), and 25, 50, and 75% decreased water supply levels were applied as subplots of the experiment. Results of the field experiments showed that yield suitable for processing (68.7-72.7 t ha⁻¹) and paste output (12.2-12.9 t ha⁻¹) were obtainable under conditions of I₁ application (p < 0.01). MFW, FD, PV, and TSS were significantly affected from treatments (p < 0.05). High stress resulted in the highest soluble solids. The total irrigation water amount and water consumptive use of the mentioned application (I₁) were determined as 426 and 525 mm in 2004. In 2005, the total irrigation water amount and water consumptive use of the same treatment were 587 and 619 mm, respectively.     

Forage quality, water use and nitrogen utilization efficiencies of pearl millet (Pennisetum americanum L.) grown under different soil moisture and nitrogen levels

The increasing scarcity of water for irrigation is becoming the most important problem for producing forage in all arid and semi-arid regions. Pearl millet is a key crop in these regions which needs relatively less water than other crops. In this research, a field study was conducted to identify the best combination of irrigation and nitrogen (N) management to achieve acceptable pearl millet forage both in quantity and quality aspects. Pearl millet was subjected to four irrigation treatments with interaction of N fertilizer (0, 75, 150 and 225 kg ha⁻¹). The irrigation treatments were 40%, 60%, 80% and 100% of total available soil water (I₄₀, I₆₀, I₈₀ and I₁₀₀, respectively). The results showed that increasing moisture stress (from I₄₀ to I₁₀₀) resulted in progressively less total dry matter (TDM), leaf area index (LAI), and nitrogen utilization efficiency (NUzE), while water use efficiency (WUE) and the percentage of crude protein (CP%) increased. The highest TDM and LAI were found to be 21.45 t ha⁻¹ and 8.65, in I₄₀ treatment, respectively. TDM, WUE, CP% and profit responses to N rates were positive. The maximum WUE of 4.19 kg DM/m³ was achieved at I₁₀₀ with 150 kg N ha⁻¹. The results of this research indicate that the maximum profit of forage production was obtained in plots which were fully irrigated (I₄₀) and received 225 kg N ha⁻¹. However, in the situation which water is often limited and not available, application of 150 kg N ha⁻¹ can produce high forage quality and guaranty acceptable benefits for farmers.     

Effect of brackish water irrigation and straw mulching on soil salinity and crop yields under monsoonal climatic conditions

Fresh water shortages are severally restricting sustainable agriculture development in the North China Plain. The scarcity of fresh water has forced farmers to use brackish water from shallow underground sources, which helps to overcome drought and increase crop yields but also increases the risk of soil salinization. To identify safe and effective ways of using brackish water in this region, field experiments were conducted to evaluate the effect of brackish water irrigation and straw mulching on soil salinity and crop yield in a winter wheat-summer maize double cropping system. The experiment was in a split-plot design. Six rates of straw mulching (0, 4.5, 6.0, 7.5, 15.0 and 30.0 Mg/ha) were assigned to the main plots and two irrigation water qualities (i.e. brackish water with salt content of 3.0-5.0 g/L and fresh water with only 1.27 g salt/L) were applied to subplots. The brackish water irrigation significantly increased the salt content at different soil depths in the upper 1 m soil layer during the two growing seasons. Straw mulching affected the vertical distribution of salt in the brackish water irrigation plots and the average salt content of straw mulch treatments (4.5, 6.0, 7.5, 15.0 and 30.0 Mg/ha) within the 0-20, 20-40 and 0-100 cm soil depths was 10.2, 14.0 and 1.8% lower than that without straw mulch (A₀). No salt accumulation occurred to a depth of 1 m in the brackish water irrigation plots and there was no correlation between the value of SAS (salt accumulated in 1 m of soil) and straw mulch rate. In 2000 and 2001, the salt content within the 0-40 cm soil layer in brackish water irrigation plots increased due to high evaporation rates during April-June, and then decreased up to September as salts were leached by rain. For the fresh water irrigation plots, the salt content remained relatively stable. Straw mulching affected the salt content in the 0-40 cm soil layer in brackish water irrigation plots in different periods of 2000 and 2001, but no correlation between salt content and straw mulch rates was observed except in September of 2000. Unlike for wheat, the yield of maize increased as the straw mulch rate increased according to the equation, y = 0.1589x + 5.3432 (R² = 0.6506). Our results would be helpful in adopting brackish water irrigation and straw mulching in ways that enhance crop yields and reduce the risk of soil salinization. However, long-term effects of brackish water irrigation and straw mulching on soil salinity and crop yield need to be further evaluated for sustainability of the system.     

Contrasting methods for estimating evapotranspiration in soybean

Crop scientists are often interested in canopy rather than leaf water estimates. Comparing canopy fluxes for multiple treatments using micrometeorological approaches presents limitations because of the large fetch required. The goal of this study was to compare leaf-scale to field-scale data by summing soil water evaporation (E) and leaf transpiration (T) versus ET using tower eddy covariance (EC) and scaling leaf transpiration to the canopy level using a two-step scaling approach in soybean [Glycine max (L.) Merr.]. Soybean transpiration represented 89-96% of E + T when combining the soil water evaporation with leaf transpiration on the five measurement days during reproductive growth. Comparing E + T versus ET from the EC system, the E + T method overestimated ET from 0.68 to 1.58 mm. In terms of percent difference, the best agreement between the two methods was 15% on DOY 235 and the worst agreement occurred on DOY 234 (41%). A two-step scaling method predicted average ET within 0.01 mm of the EC ET between 10:00 and 14:15 on an hourly time-step on DOY 227 under uniform sky conditions and average ET within 0.03 mm of the EC ET on DOY 235 under intermittent sky conditions between 10:00 and 15:15. Pooling the scaled-leaf data and comparing them with the measured EC ET data exhibited a strong linear relationship (r = 0.835) after accounting for bias (6%). Findings from this study indicate satisfactory results comparing absolute differences are likely not obtainable by summing leaf transpiration with soil water evaporation to calculate canopy water fluxes. However, scaling leaf transpiration provided a robust measure of canopy transpiration during reproductive growth in soybean under these conditions and merits additional study under different climatic and crop conditions.