Purge and trap method for determination of volatile halocarbons and carbon disulfide in table-ready foods

A method developed for the determination of ethylene dibromide in table-ready foods has been modified and expanded to include 7 other volatile halocarbons and carbon disulfide. Samples are stirred with water and purged with nitrogen for 0.5 h in a water bath at 100 degrees C. The analytes collected on a duplex trap composed of Tenax TA and XAD-4 resin are eluted with hexane and determined by gas chromatography with electron capture detection or Hall electrolytic conductivity detection. Flame photometric detection in the sulfur mode is used to determine carbon disulfide. Thick-film, wide-bore capillary columns are used exclusively in both the determination and confirmation of the halogenated analytes. The higher levels of analytes are also confirmed by full scan gas chromatography mass spectrometry (GC/MS). Samples are analyzed for carbon disulfide, methylene chloride, chloroform, 1,2-dichloroethane, methyl chloroform, carbon tetrachloride, trichloroethylene, 1,2-dibromoethane, and tetrachloroethylene. Initially, 19 table-ready foods from the Food and Drug Administration's Total Diet Study were analyzed by this method. A limited survey of those food items exhibiting high levels of analytes was conducted. Samples exhibited levels up to 3300 ppb (methyl chloroform in Parmesan cheese). Recoveries of all 9 analytes from fortified samples ranged from 83 to 104%. Chromatograms from this purge and trap method are clean, enabling quantitation levels of low parts per billion and sub-parts per billion to be achieved for the halogenated analytes. The quantitation limit for carbon disulfide is 12 ppb. Two compounds found in drinking water were identified by GC/MS as bromodichloromethane and chlorodibromomethane. Drinking water from several cities was analyzed for these trihalomethanes as well as for bromoform. Levels of up to 17 ppb bromodichloromethane were found. Recoveries ranged from 96 to 103%.     

Detection of ochratoxin A in barley, using silica gel minicolumns.

A simplified procedure has been developed to detect ochratoxin A in cereals which can be used in the field where equipment for thin layer chromatography is not available. The procedure includes extraction of the acidified sample with chloroform, purification over sodium bicarbonate, and minicolumn chromatography. Under longwave ultraviolet light ochratoxin A appears as a blue-green fluorescent band at the lower end of the column. Contamination levels as low as 12 ppb can be detected by this method.     

A screening method for determining nitrofuran drug residues in animal tissues.

A method was developed for measuring low levels of total nitrofurans in animal tissues and milk. The antimicrobial nitrofurans (5 or more products) used in agriculture are extracted from tissue with aqueous acid in the presence of ethyl acetate. After centrifugation and evaporation, the organic residue is washed with hexane and the nitrofurans are hydrolyzed to 5-nitrofuraldehyde in aqueous acid at 70 degrees C. The hydrolysis product is extracted with benzene and measured by gas-liquid chromatography with electron capture detection. Recoveries of nitrofurazone and furazolidone from fortified poultry and swine tissues at the levels of 0.5 and 0.1 ppm are 75 and 65%, respectively. This procedure can be used to detect the total nitrofuran content of as little as 10 ppb muscle tissues and milk, 100 ppb liver, and 50 ppb fat with no interference from related veterinary nitrodrugs.     

Flavor threshold for acetaldehyde in milk, chocolate milk, and spring water using solid phase microextraction gas chromatography for quantification

The detection threshold of acetaldehyde was determined on whole, lowfat, and nonfat milks, chocolate-flavored milk, and spring water. Knowledge of the acetaldehyde threshold is important because acetaldehyde forms in milk during storage as a result of light oxidation. It is also a degradation product of poly(ethylene terephthalate) during melt processing, a relatively new packaging choice for milk and water. There was no significant difference in the acetaldehyde threshold in milk of various fat contents, with thresholds ranging from 3939 to 4040 ppb. Chocolate-flavored milk and spring water showed thresholds of 10048 and 167 ppb, respectively, which compares favorably with previous studies. Solid phase microextraction (SPME) was verified as an effective method for the recovery of acetaldehyde in all media with detection levels as low as 200 and 20 ppb in milk and water, respectively, when using a polydimethyl siloxane/Carboxen SPME fiber in static headspace at 45 degrees C for 15 min.     

Competitive direct enzyme-linked immunosorbent screening assay for the detection of sulfamethazine contamination of animal feeds.

A sensitive screening method has been developed for detecting sulfamethazine (SMZ) contamination of feeds by using either polyclonal or monoclonal antibodies and a direct competitive enzyme-linked immunosorbent screening assay (ELISA). Feed samples of 25.0 g are extracted with 0.5N HCl and centrifuged. The extract is adjusted to pH 7.0 with 3.0N NaOH and recentrifuged. This pH-adjusted extract is used in the ELISA. Levels as low as 0.004 micrograms SMZ/g feed were detected in supplemented extracts by polyclonal antibodies; levels of 0.4 micrograms SMZ/g feed were detected by a monoclonal antibody.     

Sulfamethazine (sulfadimidine) residues in Canadian consumer milk

A survey on the presence of sulfamethazine (sulfadimidine) residues in consumer milk has been conducted in 10 cities across Canada. In each city, homogenized milk was purchased at 3 different retail outlets, each supplied by different processing plants. A total of 30 samples was analyzed by a liquid chromatographic method. The limit of quantitation was 5 ppb. In addition to automatic integration, visual inspection of the chromatograms was required to distinguish between low concentrations of sulfamethazine and 2 unknown interfering peaks. Two samples, from different cities, contained 11.4 and 5.24 ppb of the drug. Drug identity was confirmed by mass spectrometry. All other samples appeared to be free of the drug.     

Purge and trap method for determination of fumigants in whole grains, milled grain products, and intermediate grain-based foods

A method developed for the determination of 1,2-dibromoethane in whole grains and grain-based products has been modified and expanded to include 8 other fumigants. Samples are stirred with water and purged with nitrogen for 0.5 h in a water bath at 100 degrees C. The fumigants are collected on a trap composed of Tenax TA and XAD-4 resin, eluted with hexane, and determined by gas chromatography (GC) using electron capture detection or Hall electrolytic conductivity detection. Flame photometric detection in the sulfur mode is used to determine carbon disulfide. Thick-film, wide-bore capillary columns were used exclusively in both the determination and confirmation of the halogenated fumigants. The higher levels of fumigants are also confirmed by full scan GC/mass spectrometry. Samples are analyzed for carbon disulfide, methylene chloride, chloroform, 1,2-dichloroethane, methyl chloroform, carbon tetrachloride, trichloroethylene, 1,2-dibromoethane, and tetrachloroethylene. A total of 25 whole grains, milled grain products, and intermediate grain-based foods analyzed by this method contained fumigant levels up to 51 ppm (carbon tetrachloride in wheat). Recoveries from fortified samples ranged from 82 to 104%. Chromatograms from this purge and trap method are clean, so that low parts per billion and sub-parts per billion levels can be quantitated for the halogenated analytes. The quantitation level for carbon disulfide is 12 ppb.     

Comparison of methods for extraction of organic N monomers from soil microbial biomass

One way of investigating the function of soil is via the pool of low molecular weight organic compounds in the soil microbial biomass. This is because low molecular weight organic compounds have key roles in metabolism of soil microbes, can function in osmotic adjustment and other stress responses, and are intermediates in the breakdown of polymers to inorganic nutrients. Methods for measuring low molecular weight microbial metabolites in soil rely upon extracting total metabolites and then subtracting the contribution from metabolites in the soil extracellular matrix (i.e. microbial = total − extracellular). Recent studies have tested methods for extracting organic N monomers from the extracellular matrix of soil, but there has not been similar testing of methods for extracting total organic N monomers. The aims of this study were to examine methods for extracting total organic N monomers by a) contrasting chloroform gas fumigation with chloroform direct extraction, and b) examining whether it is possible to extract soil with two methods that combine quenching of metabolic activity with extraction, namely cold methanol/chloroform/water and hot aqueous ethanol. To evaluate methods, organic N compounds were extracted from soil and then capillary electrophoresis–mass spectrometry identified and quantified 42 organic N monomers including amino acids, quaternary ammonium compounds, nucleobases and nucleosides, amines and polyamines. Absolute concentrations of 32 out of the 42 quantified organic N monomers were significantly different between soil extracted by chloroform gas fumigation and chloroform direct extraction. These differences were probably a function of gains and losses of compounds due to oxidation, hydrolysis and deamidation during the two-day chloroform gas fumigation. Cold methanol/chloroform/water yielded large amounts of the extremely labile compound ergothioneine, probably because the extraction method rapidly quenched metabolic activity. The primary limitation of extraction with methanol/chloroform/water is that it was ineffective at extracting strongly cationic compounds (e.g. polyamines). Extraction with hot aqueous ethanol was unsuccessful with soil presumably because soil microbes are difficult to lyse. It is recommended that future studies examining organic N monomers in soil microbial biomass use chloroform direct extraction or cold methanol/chloroform/water rather than chloroform gas fumigation.     

Improved cleanup for liquid chromatographic analysis and fluorescence detection of aflatoxins M1 and M2 in fluid milk products

A rapid method is described for extraction and cleanup of raw and processed milk for determination of aflatoxins M1 and M2 by using a C18 Sep-Pak/silica gel cleanup column combination. Aflatoxins are separated by normal phase liquid chromatography and their concentrations are determined by fluorescence detection in a silica gel-packed flow cell. Recoveries ranged from 99 to 103% with coefficients of variation less than 2% for M1 levels of 0.117-1.17 ng/mL added to raw milk. Similar recoveries were obtained for M2. The coefficient of variation for analysis of 5 subsamples of naturally contaminated milk was less than 1%. Agreement with the official method is satisfactory. Each sample requires less than 25 mL solvent and 10 min actual handling time. Sample chromatograms show no interferences in the M1-M2 elution region and no late-eluting peaks, which permits spacing injections at 13-20 min intervals. Aflatoxin levels as low as 0.03 ppb may be determined by this procedure. Extracts have also been analyzed by thin layer chromatography.     

Determination of morantel-related residues in bovine milk by electron capture gas chromatography

A gas chromatographic assay was developed to determine major residues of morantel in bovine milk over a range that is suitable for monitoring residues of the drug. The method is based on hydrolysis of the N-methyl-tetrahydropyrimidine portion of morantel and its metabolites to N-methyl-1,3-propanediamine, and converting the diamine to an N,N-bis-(2-nitro-4-trifluoromethylphenyl) derivative. The addition of an internal standard, the N-desmethyl-N-ethyl homolog of pyrantel, to the milk sample circumvents any potential problem that could arise from variable reaction yields, and eliminates the true recovery as a factor affecting the accuracy and precision of the procedure. The concentrations of the derivatives are determined by pulsed electron capture gas chromatography over a linear dynamic range that is equivalent to 12.5-50 ppb morantel. The method was evaluated at the 0, 12.5, 25, and 50 ppb levels in fortified bovine milk, and in a withdrawal sample containing physiologically incurred morantel residues. Mean values of 14 +/- 1.7, 24 +/- 3.7, and 47 +/- 6.9 were found for the fortified samples, approximately 3 ppb for control milk, and 16 +/- 1.7 ppb for the withdrawal sample.     

Determination of aflatoxin M1 in milk and milk products contaminated at low levels

A new method is described for the determination of aflatoxin M1 in milk and dairy products by thin layer chromatography. The main characteristic is the extraction system using an alkaline solution. Lipids are removed by centrifuging at low temperatures, and the aflatoxins are then extracted with CHCl3. The method has 2 options: Technique II (detection limit 0.02 ppb) requires cleanup on a chromatographic column; this is not necessary in Technique I (detection limit 0.1 ppb). The recovery rate in both techniques is over 92.8% in milk and yoghurt. This method may also be used for other aflatoxins. Because of the advantages of the method, Technique II is recommended for aflatoxin M1 control in milk, where a low detection limit is necessary. Technique I is proposed for experimental aflatoxin production studies in dairy products, which require analysis of a large number of samples but which do not require a very low detection limit.     

Gas chromatographic determination of incurred dimetridazole residues in swine tissues

A gas chromatographic method for determination of 2-hydroxymethyl-1-methyl-5-nitroimidazole (DMZOH), the hydroxy metabolite of dimetridazole, in swime muscle has been developed. The method uses cleanup steps similar to those of an earlier polarographic method. The present method is capable of quantitating levels as low as 2 ppb and detecting less than 1 ppb. Recoveries from 30 control tissues spiked at 1, 2, or 4 ppb averaged 80.4%. Performance of the method in incurred tissue was documented and limited data on the depletion of the metabolite in muscle were generated. The muscle of swine given 150 ppm dimetridazole in feed for 14 days contained less than 1 ppb DMZOH at 12 h withdrawal time.     

Simple and rapid liquid chromatography-tandem mass spectrometry confirmatory assay for determining amoxicillin and ampicillin in bovine tissues and milk

A simple specific and rapid confirmatory method for determining the two amphoteric penicillins, that is, amoxicillin and ampicillin, in bovine muscle, liver, kidney, and milk is presented. This method is based on the matrix solid-phase dispersion technique with hot water as extractant followed by liquid chromatography (LC)-tandem mass spectrometry. With this instrumentation, the selected reaction monitoring acquisition mode with two fragmentation reactions for each analyte was adopted. After acidification and filtration of the aqueous extracts, 25 microL of the tissue final extracts and 50 microL of the milk final extract were injected into the LC apparatus. Absolute recovery of the two analytes in any biological matrix at the 50 ppb level in tissues and the 4 ppb level in milk was 74-95% with relative standard deviations (RSDs) of no larger than 9%. When penicillin V was used as surrogate internal standard, relative recovery of the targeted compounds present in bovine tissues and milk at, respectively, 25 and 2 ppb levels ranged between 100 and 106% with RSDs of no larger than 11%. When fractionation of analytes by using a short chromatographic run was attempted, remarkable signal weakening for the two analytes was experienced. This effect was traced to polar endogenous coextractives eluted in the first part of the chromatographic run that interfered with the gas-phase ion formation of the two penicillins. Slowing the chromatographic run eliminated this unwelcome effect. Limits of quantification of the two analytes in bovine milk were estimated to be <1 ppb, whereas amoxicillin and ampicillin could be quantified in bovine tissues down to 3.1 and 0.8 ppb levels, respectively.     

Determination of N-nitrosodimethylamine in nonfat dry milk: collaborative study

Ten laboratories participated in a collaborative study of a method for the determination of N-nitrosodimethylamine (NDMA) in nonfat dry milk. NDMA is eluted with dichloromethane from a mixture of Celite, acidic sulfamic acid, and nonfat dry milk (all packed in a chromatography column), concentrated in a Kuderna -Danish concentrator, and finally analyzed by a GC-thermal energy analyzer technique. Ten samples were studied: 6 were naturally contaminated (NDMA levels 0.38-3.56 ppb) and 4 were spiked with known levels (0.96 and 3.2 ppb) of NDMA. The coefficients of variation (CV) of the complete data for the naturally contaminated samples (excluding the 2 samples containing the lowest levels) were 8.5% and 22.5% for repeatability and reproducibility, respectively. The corresponding CVs for the spiked samples were 14.4% and 20.4%, respectively. The percent recoveries of the added NDMA in the spiked samples (at the 2 levels indicated above) were 101.6 +/- 3.2 (omitting 1 outlier) and 95 +/- 2.1, respectively. The method has been adopted official first action.     

Determination and confirmation of 5-hydroxyflunixin in raw bovine milk using liquid chromatography tandem mass spectrometry

A method was developed and validated to determine 5-hydroxyflunixin in raw bovine milk using liquid chromatography tandem mass spectrometry (LC/MS/MS). The mean recovery and percentage coefficient of variation (%CV) of 35 determinations for 5-hydroxyflunixin was 101% (5% CV). The theoretical limit of detection was 0.2 ppb with a validated lower limit of quantitation of 1 ppb and an upper limit of 150 ppb. Accuracy, precision, linearity, specificity, ruggedness, and storage stability were demonstrated. A LC/MS/MS confirmatory method using the extraction steps of the determinative method was developed and validated for 5-hydroxyflunixin in milk from cattle. Briefly, the determinative and confirmatory methods were based on an initial solvent (acetone/ethyl acetate) precipitation/extraction of acidified whole milk. The solvent precipitation/extraction effectively removed incurred ((14)C) residues from milk samples. The organic extract was then purified by solid phase extraction (SPE) using a strong cation exchange cartridge (sulfonic acid). The final SPE-purified sample was analyzed using LC/MS/MS. The methods are rapid, sensitive, and selective and provide for the determination and confirmation of 5-hydroxyflunixin at the 1 and 2 ppb levels, respectively.     

A quantitative method for determination of aflatoxin B in roasted corn.

Roasting aflatoxin-contaminated corn will reduce toxin levels. A quantitative analysis for aflatoxin in roasted corn has been developed by modifying a cleanup technique for green coffee extracts approved as official first action by the AOAC. A chloroform extract is partially purified on a Florisil column, and thin layer chromatographic (TLC) plates are developed with methylene chloride-chloroform-isoamyl alcohol-formic acid (81+15+3+1). Recoveries average 101% and the sensitivity limit is 5 ppb aflatoxin B1. A 2-dimensional TLC procedure can also be used to separate the aflatoxins from background interferences.     

Rapid thin layer chromatographic determination of aflatoxin M1 in powdered milk

A method has been developed for the detection of aflatoxin M1 in milk. The toxin is extracted with chloroform, the extract is evaporated, and the residue is partitioned between carbon tetrachloride and an aqueous saline-methanol solution. The toxin is once again extracted with chloroform from the methanol solution and analyzed by thin layer chromatography. The limit of detection of M1 in powdered milk is 0.5 microgram/kg; recoveries of added M1 are about 83%. The limit of detection can be improved to 0.3 microgram/kg if the plate is sprayed with an aqueous solution of H2SO4 after development.     

Liquid chromatographic method for multiresidue determination of benzimidazoles in beef liver and muscle: collaborative study

A liquid chromatographic method for determination of thiabendazole, 5-hydroxythiabendazole, oxfendazole, mebendazole (MBZ), and fenbendazole (FBZ) in cattle liver and muscle was collaboratively studied in 7 laboratories in 1986. For blind fortified samples containing 800 ppb FBZ, average recovery and relative standard deviations for repeatability and reproducibility (RSDr and RSDR) based on results from 6 of the participating laboratories were 83%, 12.7%, and 14.0%, respectively. Recoveries of FBZ from incurred liver samples were more variable. Recoveries of MBZ from livers fortified at the 100 ppb level were encouraging; however, the drug levels were too low in the incurred samples used for MBZ studies. Except for FBZ and MBZ in liver, the study data were not satisfactory. The method has been adopted official first action by AOAC for determination of 800-1600 ppb fenbendazole in liver. The analysis should be repeated using a smaller sample size when initial analyses show levels greater than 1600 ppb FBZ.     

Malondialdehyde contents in infant milk formulas

Malondialdehyde (MDA) levels in infant milk formulas have been monitored by using an aqueous acid extraction method combined with the thiobarbituric acid method (TBA-test). Vegetable oils, with a remarkable content of polyunsaturated fatty acids (PUFA) are used to enrich the infant milk formulas. As PUFA are more susceptible to autoxidation, it becomes of great interest to have information about the safety and preservation of these products. We monitored MDA content in twenty of the most popular infant milk formulas and in some commercial cow milk samples and compared the obtained data. Levels of MDA ranged between 200 and 1200 ppb: all values but one were higher, up to five times, than those found in cow milk samples. To evaluate the accuracy of the data obtained from the TBA-test, some samples were also analyzed with an HPLC derivative method: preliminary results show a good agreement between the two analytical techniques.     

Gas chromatographic-thermal energy analysis method for determination of volatile N-nitrosamines in baby bottle rubber nipples: collaborative study

A collaborative study was conducted on the U.S. Food and Drug Administration (FDA) dichloromethane extraction method for determining volatile N-nitrosamines in baby bottle rubber nipples. Following dichloromethane extraction, N-nitrosamines were determined by gas chromatography-thermal energy analysis. Six pairs of blind duplicate rubber nipple samples representing 6 lots were analyzed by 11 collaborating laboratories. All samples were portions taken from equilibrated composites of cut-up rubber nipples obtained from manufacturers in the United States. Recoveries of the internal standard (N-nitrosodipropylamine) at approximately 20 ppb ranged from 10 to 120%. Reproducibility relative standard deviations (RSDx) were between 35 and 45% for N-nitrosamine levels from 10 to 20 ppb. However, when data from laboratories with recoveries less than 75% were excluded (this is now specified in the method), RSDx values were between 11 and 32% for N-nitrosamine levels from 6 to 26 ppb. Values were consistent with or better than those reported for other analytical techniques designed to quantitate trace contaminants at the low ppb level, e.g., aflatoxin in foods. The method has been adopted official first action for the quantitation of volatile N-nitrosamines in baby bottle rubber nipples.