Evaluating the Crop Water Stress Index and its correlation with latent heat and CO2 fluxes over winter wheat and maize in the North China plain

Plant water status is a key factor impacting crop growth and agricultural water management. Crop water stress may alter canopy temperature, the energy balance, transpiration, photosynthesis, canopy water use efficiency, and crop yield. The objective of this study was to calculate the Crop Water Stress Index (CWSI) from canopy temperature and energy balance measurements and evaluate the utility of CWSI to quantify water stress by comparing CWSI to latent heat and carbon dioxide (CO₂) flux measurements over canopies of winter wheat (Triticum aestivum L.) and summer maize (Zea mays L.). The experiment was conducted at the Yucheng Integrated Agricultural Experimental Station of the Chinese Academy of Sciences from 2003 to 2005. Latent heat and CO₂ fluxes (by eddy covariance), canopy and air temperature, relative humidity, net radiation, wind speed, and soil heat flux were averaged at half-hour intervals. Leaf area index and crop height were measured every 7 days. CWSI was calculated from measured canopy-air temperature differences using the Jackson method. Under high net radiation conditions (greater than 500 W m⁻²), calculated values of minimum canopy-air temperature differences were similar to previously published empirically determined non-water-stressed baselines. Valid measures of CWSI were only obtained when canopy closure minimized the influence of viewed soil on infrared canopy temperature measurements (leaf area index was greater than 2.5 m² m⁻²). Wheat and maize latent heat flux and canopy CO₂ flux generally decreased linearly with increases in CWSI when net radiation levels were greater than 300 W m⁻². The responses of latent heat flux and CO₂ flux to CWSI did not demonstrate a consistent relationship in wheat that would recommend it as a reliable water stress quantification tool. The responses of latent heat flux and CO₂ flux to CWSI were more consistent in maize, suggesting that CWSI could be useful in identifying and quantifying water stress conditions when net radiation was greater than 300 W m⁻². The results suggest that CWSI calculated by the Jackson method under varying solar radiation and wind speed conditions may be used for irrigation scheduling and agricultural water management of maize in irrigated agricultural regions, such as the North China Plain.     

Comparisons of energy balance and evapotranspiration between flooded and aerobic rice fields in the Philippines

The seasonal and annual variability of sensible heat flux (H), latent heat flux (LE), evapotranspiration (ET), crop coefficient (K_c) and crop water productivity (WP_ET) were investigated under two different rice environments, flooded and aerobic soil conditions, using the eddy covariance (EC) technique during 2008-2009 cropping periods. Since we had only one EC system for monitoring two rice environments, we had to move the system from one location to the other every week. In total, we had to gap-fill an average of 50-60% of the missing weekly data as well as those values rejected by the quality control tests in each rice field in all four cropping seasons. Although the EC method provides a direct measurement of LE, which is the energy used for ET, we needed to correct the values of H and LE to close the energy balance using the Bowen ratio closure method before we used LE to estimate ET. On average, the energy balance closure before correction was 0.72 ± 0.06 and it increased to 0.99 ± 0.01 after correction. The G in both flooded and aerobic fields was very low. Likewise, the energy involved in miscellaneous processes such as photosynthesis, respiration and heat storage in the rice canopy was not taken into consideration.Average for four cropping seasons, flooded rice fields had 19% more LE than aerobic fields whereas aerobic rice fields had 45% more H than flooded fields. This resulted in a lower Bowen ratio in flooded fields (0.14 ± 0.03) than in aerobic fields (0.24 ± 0.01). For our study sites, evapotranspiration was primarily controlled by net radiation. The aerobic rice fields had lower growing season ET rates (3.81 ± 0.21 mm d⁻¹) than the flooded rice fields (4.29 ± 0.23 mm d⁻¹), most probably due to the absence of ponded water and lower leaf area index of aerobic rice. Likewise, the crop coefficient, K_c, of aerobic rice was significantly lower than that of flooded rice. For aerobic rice, K_c values were 0.95 ± 0.01 for the vegetative stage, 1.00 ± 0.01 for the reproductive stage, 0.97 ± 0.04 for the ripening stage and 0.88 ± 0.03 for the fallow period, whereas, for flooded rice, K_c values were 1.04 ± 0.04 for the vegetative stage, 1.11 ± 0.05 for the reproductive stage, 1.04 ± 0.05 for the ripening stage and 0.93 ± 0.06 for the fallow period. The average annual ET was 1301 mm for aerobic rice and 1440 mm for flooded rice. This corresponds to about 11% lower total evapotranspiration in aerobic fields than in flooded fields. However, the crop water productivity (WP_ET) of aerobic rice (0.42 ± 0.03 g grain kg⁻¹ water) was significantly lower than that of flooded rice (1.26 ± 0.26 g grain kg⁻¹ water) because the grain yields of aerobic rice were very low since they were subjected to water stress.The results of this investigation showed significant differences in energy balance and evapotranspiration between flooded and aerobic rice ecosystems. Aerobic rice is one of the promising water-saving technologies being developed to lower the water requirements of the rice crop to address the issues of water scarcity. This information should be taken into consideration in evaluating alternative water-saving technologies for environmentally sustainable rice production systems.     

Five methods to interpret field measurements of energy fluxes over a micro-sprinkler-irrigated mango orchard

Energy balance measurements were carried out in a mango orchard during two growing seasons in the semi-arid region of Brazil. The actual evapotranspiration (ET) was acquired by eddy correlation (EC) and Bowen ratio energy balance (BR) techniques. The daily energy balance closure in the EC measurements showed an average gap of 12%, with a root mean square error (RMSE) of 1.7 MJ m⁻² d⁻¹. Three different correction procedures were tested for closing the energy balance from the EC system: (1) the surface energy balance residual method (RES), (2) the Bowen ratio determined from the EC fluxes, the combination approach (EC_BR), and (3) a new regression energy balance closure technique (REG). All closing energy balance methods presented good correlation with the direct EC measurements, but the trends were not similar. The latent heat fluxes estimated by the BR method—λE _BR—were higher than those from the direct EC measurements—λE _EC. When using the RES method, the half-hour λE _EC measurements represented around 88% of the λE _RES values, as the uncertainties of net radiation—R _n—and soil heat fluxes—G—are propagated into the RES method. The latent heat flux derived from the combination approach—λE _{EC_BR}—also brings these uncertainties, being the agreements comparable with those for RES method. It was therefore concluded that a single correction method for EC measurements considering only the latent and sensible heat fluxes does not exist. A new way to solve the lack of energy balance closure from EC techniques was tested by means of a curve fitting, the REG method. Considering the REG corrections applied to the energy balance components involving all periods of the day and the average conditions of the two growing seasons, half-hour values of λE _EC were overmeasured by 18%, H _EC was undermeasured by 17%, and G values required a correction of 466%. The REG method appeared promising because it considers different weights for all energy balance components in the optimization process. Taking the REG results for the drier second growing season as a reference, it was concluded that seasonal ET values by the other methods in mango orchard ranged from 7 to 28% higher, showing that turbulent flux measurements lack accuracy for executing on-farm water-saving programmes and calibrating transient soil water flow models.     

Variability in energy partitioning and resistance parameters for a vineyard in northwest China

Grapevines are extensively grown in the semiarid and arid regions, but little information is available on the variability of energy partitioning and resistance parameters for the vineyard. To address this question, an eddy covariance system was applied to measure energy balance over a vineyard in northwest China during 2005-2006. Result indicated that 2-year average Bowen ratio (β) of vineyard was 1.0, canopy resistance (r_c) 289.3 s m⁻¹, aerodynamic resistance (r_a) 9.7 s m⁻¹ and climatological resistance (r_i) 117 s m⁻¹. This implied that the annual energy was split almost equally between sensible heat and latent heat. Compared to the corresponding values in other ecosystems reported by Wilson et al. [Wilson, K.B., Baldocchi, D.D., Aubinet, M., Berbigier, P., Bernhofer, C., Dolman, H., Falge, E., Field, C., Goldstein, A., Granier, A., Grelle, A., Halldor, T., Hollinger, D., Katul, G., Law, B.E., Lindroth, A., Meyers, T., Moncrieff, J., Monson, R., Oechel, W., Tenhunen, J., Valentini, R., Verma, S., Vesala, T., Wofsy, S., 2002. Energy partitioning between latent and sensible heat flux during the warm season at FLUXNET sites. Water Resource Research 38, 1294-1305.], the vineyard had a higher β, r_c and r_i than deciduous forests, corn and soybean, and grassland. Such difference was mainly attributed to (1) serious water stress in 2005, which resulted in a greater r_c up to 364.4 s m⁻¹; (2) sparse canopy with row spacing of 2.9 m and plant spacing of 1.8 m; (3) warm-dry climate and high attitude (1581 m) along with higher r_i and lower psychrometer (54 Pa K⁻¹) in the arid region of northwest China. These characters of vineyard revealed varying process of energy partitioning and surface resistance, and provided a scientific basis in understanding and modeling water and energy balance for the vineyard in the semiarid and arid regions.     

Use of saline aquaculture wastewater to irrigate salt-tolerant Jerusalem artichoke and sunflower in semiarid coastal zones of China

In 2004 and 2005, the feasibility of agricultural use of saline aquaculture wastewater for irrigation of Jerusalem artichoke and sunflower was conducted in the Laizhou region using saline aquaculture wastewater mixed with brackish groundwater at different ratios. Six treatments with different electrical conductivities (EC) were included in the experiment: CK1 (rainfed), CK2 (irrigation with freshwater, EC of 0.02 dS m⁻¹), and saline aquaculture wastewater (EC of 39.2 dS m⁻¹) mixed with brackish groundwater (EC of 4.4 dS m⁻¹) at volumetric ratios of 1:1, 1:2, 1:3, and 1:4 with corresponding EC of 22.0, 16.1, 13.2, and 11.4 dS m⁻¹. Soil electrical conductivity (ECe) in the saline aquaculture wastewater irrigation treatments was significantly higher (P ≤ 0.05) than that in the rainfed or freshwater irrigation treatments, and the maximum value occurred in the 22.0 dS m⁻¹ treatment. The sodium adsorption ratio (SAR) ranged from 4.1 to 11.7 mmol^1/2 L^−1/2 and increased with decreasing salinity of irrigation water. The biomass of Jerusalem artichoke significantly decreased (P ≤ 0.05) when irrigated with saline aquaculture wastewater compared to the rainfed or freshwater irrigation treatments; however, the effect of salinity on root biomass was much smaller than the aerial parts. Concomitantly, the highest tuber yield of Jerusalem artichoke occurred in the 11.4 dS m⁻¹ treatment, while the highest seed yield of sunflower occurred in the rainfed treatment. Additionally, nitrogen and phosphorus concentrations of Jerusalem artichoke were significantly higher in the 11.4 dS m⁻¹ treatment than the other treatments. This study demonstrated that properly diluted saline aquaculture wastewater can be used successfully to irrigate Jerusalem artichoke with higher economic yield and nutrient removal, but not sunflower due to the difference in salt tolerance.     

Effects of deficit irrigation on the yield and yield components of drip irrigated cotton in a mediterranean environment

A field study on cotton (Gossypium hirsutum L., cv.) was carried out from 2005 to 2008 in the Çukurova Region, Eastern Mediterranean, Turkey. Treatments were designated as I₁₀₀ full irrigation; DI₇₀, DI₅₀ and DI₀₀ which received 70, 50, and 0% of the irrigation water amount applied in the I₁₀₀ treatment. The irrigation water amount to be applied to the plots was calculated using cumulative pan evaporation that occurred during the irrigation intervals. The effect of water deficit or water stress on crop yield and some plant growth parameters such as yield response, water use efficiencies, dry matter yield (DM), leaf area index (LAI) as well as on lint quality components was evaluated. The average seasonal evapotranspiration ranged from 287 ± 15 (DI₀₀) to 584 ± 80 mm (I₁₀₀). Deficit irrigation significantly affected crop yield and all yield components considered in this study. The average seed cotton yield varied from 1369 ± 197 (DI₀₀) to 3397 ± 508 kg ha⁻¹ (I₁₀₀). The average water use efficiency (WUE_ET) ranged from 6.0 ± 1.6 (I₁₀₀) to 4.8 ± 0.9 kg ha⁻¹ mm⁻¹ (DI₀₀), while average irrigation water use efficiency (WUE_I) was between 9.4 ± 3.0 (I₁₀₀) and 14.4 ± 4.8 kg ha⁻¹ mm⁻¹ (DI₅₀). Deficit irrigation increased the harvest index (HI) values from 0.26 ± 0.054 (I₁₀₀) to 0.32 ± 0.052 kg kg⁻¹ (DI₅₀). Yield response factor (Ky) was determined to be 0.98 based on four-year average. Leaf area index (LAI) and dry matter yields (DM) increased with increasing water use. This study demonstrated that the full irrigated treatment (I₁₀₀) should be used for semiarid conditions with no water shortage. However, DI₇₀ treatment needs to be considered as a viable alternative for the development of reduced irrigation strategies in semiarid regions where irrigation water supplies are limited.     

Evapotranspiration of an hedge-pruned olive orchard in a semiarid area of NE Spain

The evapotranspiration of hedge-pruned olive orchards (Olea europaea L. cv. Arbequina) was measured under the semiarid conditions of the middle Ebro River Valley in a commercial olive orchard (57 ha) during 2004 and 2005. No measured ET_c values for this type of olive orchards have previously been reported. An eddy covariance system (krypton hygrometer KH20 and 3D sonic anemometer CSAT3, Campbell Scientific) was used. The eddy covariance measurements showed a lack of the energy balance closure (average imbalance of 26%). Then sensible and latent heat (LE) flux values were corrected using the approach proposed by Twine et al. (2000) in order to get daily measured olive evapotranspiration (ET_c) and crop coefficient (K_c) values. The highest measured monthly ET_c averages were about 3.1-3.3 mm day⁻¹, while the total seasonal ET_c during the irrigation period (March-October) was about 585 mm (in 2004) and 597 mm (in 2005). Monthly K_c values varied from about 1.0 (Winter) to 0.4-0.5 (Spring and Summer). These K_c values were similar to K_c values reported for round-shape canopy olive orchards, adjusted for ground cover, particularly during late Spring and Summer months when differences among measured and published K_c values were about less than 0.1.     

Calibration and validation of a remote sensing algorithm to estimate energy balance components and daily actual evapotranspiration over a drip-irrigated Merlot vineyard

A study was carried out to calibrate and validate a remote sensing algorithm (RSA) for estimating instantaneous surface energy balance components and daily actual evapotranspiration (ETa) over a drip-irrigated Merlot vineyard located in the Maule Region of Chile (35° 25′ LS; 71° 32′ LW; 125?m.a.s.l.). ETa was estimated as a function of instantaneous evaporative fraction and average daily net radiation (Rn_day) using meteorological variables in combination with reflectance data measured by a hand-held multi-spectral radiometer. The sub-models used to estimate the instantaneous net radiation (Rn_ins), soil heat flux (G _ins), and Rn_day were calibrated and validated using measurements of the surface energy balance components, incoming longwave radiation $(L \downarrow_{\text{ins}})$ , outgoing longwave radiation $(L \uparrow_{\text{ins}})$ , and surface albedo (α). The validations of instantaneous sensible heat flux (H _ins), latent heat flux (LE_ins), and ETa were carried out using turbulent energy fluxes obtained from an eddy correlation (EC) system. For reducing the moderate EC imbalance (about 11?%), turbulent energy fluxes were recalculated using the Bowen ratio method. The validation analysis indicated that the calibrated sub-models of the RSA were able to estimate Rn_ins, G _ins, H _ins, and LE_ins with a root-mean-square error (RMSE), mean absolute error (MAE), and index of agreement (IA) ranging between 16–54, 13–44?W?m^?2, and 0.72–94, respectively. Also, the RSA was able to estimate ETa with RMSE?=?0.38?mm?day^?1, MAE?=?0.32?mm?day^?1 and IA?=?0.96. These results demonstrate the potential use of reflectance and meteorological data to estimate ETa of a drip-irrigated Merlot vineyard.     

Drip irrigation of tea (Camellia sinensis L.): 1. Yield and crop water productivity responses to irrigation

The effects of drip irrigation on the yield and crop water productivity responses of four tea (Camellia sinensis (L.) O. Kuntze) clones were studied four consecutive years (2003/2004-2006/2007), in a large (9 ha) field experiment comprising of six drip irrigation treatments (labelled: I₁-I₆) and four clones (TRFCA PC81, AHP S15/10, BBK35 and BBT207) planted at a spacing of 1.20 m × 0.60 m at Kibena Tea Limited (KTL), Njombe in the Southern Tanzania in a situation of limited water availability. Each clone × drip irrigation treatment combination was replicated six times in a completely randomized design with 144 net plots each with an area of 72 m². Clone TRFCA PC81 gave the highest yields (range: 5920-6850 kg dried tea ha⁻¹) followed by clones BBT207 (5010-5940 kg dried tea ha⁻¹), AHP S15/10 (4230-5450 kg dried tea ha⁻¹) and BBK35 (3410-4390 kg dried tea ha⁻¹) and drip irrigation treatment I₂ gave the highest yields, ranging from 4954 to 6072 kg dried tea ha⁻¹) compared with those from other treatments (4113-5868 kg dried tea ha⁻¹). Most of these yields exceeded those (4200 kg dried tea ha⁻¹) obtained from overhead sprinkler irrigation system in Mufindi also Southern Tanzania, and Kibena Estate itself. Results showed that drip irrigation of tea not only increased yields but also gave water saving benefits of up to 50% from application of 50% less water to remove the cumulative soil water deficit (treatment I₂), and with labour saving of 85% for irrigation. The yield of dried tea per mm depth of water applied, i.e., “the crop water productivity” for drip irrigation of clones TRFCA PC81, BBT207 and BBK35, in 2003/2004 for instance, were 9.3, 8.5 and 7.1 kg dried tea [ha mm]⁻¹, respectively. The corresponding values in 2004/2005 were 2.7, 4.5 and 2.0 kg dried tea [ha mm]⁻¹ while the yield responses from clone AHP S15/10 were linear decreasing by 1 and 1.6 kg dried tea [ha mm]⁻¹ in 2003/2004 and 2004/2005, respectively. In 2005/2006 the crop water productivity from clones TRFCA PC81, AHP S15/10, BBK35 and BBT207 were 4.5, 0.4, 5.2 and 6.9 kg dried tea [ha mm]⁻¹, respectively with quadratic yield response functions to drip irrigation depth of water application. The results are presented and recommendations and implications made for technology-transfer scaling-up for increased use by large and smallholder tea growers.     

Effects of water infiltration and storage in cultivated soil on surface irrigation

Surface irrigation analysis and design require the knowledge of the variation of the cumulative infiltration water Z (L) (per unit area) into the soil as a function of the infiltration time t (T). The purpose of this study is to evaluate water infiltration and storage under surface irrigation in an alluvial clay soil cultivated with grape yield, and to determine if partially wetted furrow irrigation has more efficient water storage and infiltration than traditional border irrigation. The two irrigation components considered were wet (WT) and dry (DT) treatments, at which water applied when available soil water reached 65% and 50%, and the traditional border irrigation control. Empirical power form equations were obtained for measured advance and recession times along the furrow length during the irrigation stages of advance, storage, depletion and recession. The infiltration (cumulative depth, Z and rate, I) was functioned to opportunity time (t_o) in minute for WT and DT treatments as: Z_WT = 0.528 t_o^0.6, Z_DT = 1.2 t_o^0.501, I_WT = 19 t_o^−0.4, and I_DT = 36 t_o^−0.498. The irrigation efficiency and soil water distribution have been evaluated using linear distribution and relative schedule depth. Coefficient of variation (CV) was 5.2 and 9.5% for WT and DT under furrow irrigation system comparing with 7.8% in border, respectively. Water was deeply percolated as 11.88 and 19.2% for wet and dry furrow treatments, respectively, compared with 12.8% for control, with no deficit in the irrigated area. Partially wetted furrow irrigation had greater water-efficiency and grape yield than both dry furrow and traditional border irrigations, where application efficiency achieved as 88.1% for wet furrow irrigation that achieved high grape fruit yield (30.71 Mg/ha) and water use efficiency 11.9 kg/m³.     

Evaluating eddy covariance cotton ET measurements in an advective environment with large weighing lysimeters

Eddy covariance (EC) systems are being used to assess the accuracy of remote sensing methods in mapping surface sensible and latent heat fluxes and evapotranspiration (ET) from local to regional scales, and in crop coefficient development. Therefore, the objective was to evaluate the accuracy of EC systems in measuring sensible heat (H) and latent heat (LE) fluxes. For this purpose, two EC systems were installed near large monolithic weighing lysimeters, on irrigated cotton fields in the Texas High Plains, during the months of June and July 2008. Sensible and latent heat fluxes were underestimated with an average error of about 30%. Most of the errors were from nocturnal measurements. Energy balance (EB) closure was 73.2–78.0% for daytime fluxes. Thus, daylight fluxes were adjusted for lack of EB closure using the Bowen ratio/preservation of energy principle, which improved the resulting EC heat flux agreement with lysimetric values. Further adjustments to EC-based ET included nighttime ET (composite) incorporation, and the use of ‘heat flux source area’ (footprint) functions to compensate ET when the footprint expanded beyond the crop field boundary. As a result, ET values remarkably matched lysimetric ET values, with a ‘mean bias error ± root mean square error’ of −0.03 ± 0.5 mm day⁻¹ (or −0.6 ± 10.2%).     

Intercepted radiation by apple canopy can be used as a basis for irrigation scheduling

Improved approaches for irrigation scheduling require specific protocols for adaptation to different growing conditions. We assessed crop intercepted radiation as the main factor for decision on irrigation scheduling. Over two growing seasons (2007-2008), apple trees growing in a large weighing lysimeter were used to measure daily canopy transpiration (T_d). Seasonal patterns of daily canopy intercepted photosynthetically active radiation (IPAR_d) and midday stem water potential were also measured. In 2007, irrigation was withheld in two different times to study T_d responses to midday stem water potential. Before harvest, under full irrigation, T_d increased linearly with IPAR_d (R² = 0.81 in 2007 and 0.84 in 2008). With the two year data combined, R² increased from 0.74 to 0.80 when VPD was considered as a second variable. When irrigation was withheld in 2007 the ratio between T_d and IPAR_d, which is defined here as transpiratory radiation use efficiency (TRUE), decreased linearly (R² = 0.49) as midday stem water potential decreased. Due to the highly significant effect of IPAR_d and VPD on T_d, TRUE showed potential applications in estimating the amount of irrigation water.     

Soil salinity related to physical soil characteristics and irrigation management in four Mediterranean irrigation districts

Irrigated agriculture is threatened by soil salinity in numerous arid and semiarid areas of the Mediterranean basin. The objective of this work was to quantify soil salinity through electromagnetic induction (EMI) techniques and relate it to the physical characteristics and irrigation management of four Mediterranean irrigation districts located in Morocco, Spain, Tunisia and Turkey. The volume and salinity of the main water inputs (irrigation and precipitation) and outputs (crop evapotranspiration and drainage) were measured or estimated in each district. Soil salinity (EC_e) maps were obtained through electromagnetic induction surveys (EC_a readings) and district-specific EC_a-EC_e calibrations. Gravimetric soil water content (WC) and soil saturation percentage (SP) were also measured in the soil calibration samples. The EC_a-EC_e calibration equations were highly significant (P < 0.001) in all districts. EC_a was not significantly correlated (P > 0.1) with WC, and was only significantly correlated (P < 0.1) with soil texture (estimated by SP) in Spain. Hence, EC_a mainly depended upon EC_e, so that the maps developed could be used effectively to assess soil salinity and its spatial variability. The surface-weighted average EC_e values were low to moderate, and ranked the districts in the order: Tunisia (3.4 dS m⁻¹) > Morocco (2.2 dS m⁻¹) > Spain (1.4 dS m⁻¹) > Turkey (0.45 dS m⁻¹). Soil salinity was mainly affected by irrigation water salinity and irrigation efficiency. Drainage water salinity at the exit of each district was mostly affected by soil salinity and irrigation efficiency, with values very high in Tunisia (9.0 dS m⁻¹), high in Spain (4.6 dS m⁻¹), moderate in Morocco (estimated at 2.6 dS m⁻¹), and low in Turkey (1.4 dS m⁻¹). Salt loads in drainage waters, calculated from their salinity (EC_dw) and volume (Q), were highest in Tunisia (very high Q and very high EC_dw), intermediate in Turkey (extremely high Q and low EC_dw) and lowest in Spain (very low Q and high EC_dw) (there were no Q data for Morocco). Reduction of these high drainage volumes through sound irrigation management would be the most efficient way to control the off-site salt-pollution caused by these Mediterranean irrigation districts.     

Corn yield responses under crop evapotranspiration-based irrigation management

Improving irrigation water management is becoming important to produce a profitable crop in South Texas as the water supplies shrink. This study was conducted to investigate grain yield responses of corn (Zea mays) under irrigation management based on crop evapotranspiration (ET_C) as well as a possibility to monitor plant water deficiencies using some of physiological and environmental factors. Three commercial corn cultivars were grown in a center-pivot-irrigated field with low energy precision application (LEPA) at Texas AgriLife Research Center in Uvalde, TX from 2002 to 2004. The field was treated with conventional and reduced tillage practices and irrigation regimes of 100%, 75%, and 50% ET_C. Grain yield was increased as irrigation increased. There were significant differences between 100% and 50% ET_C in volumetric water content (θ), leaf relative water content (RWC), and canopy temperature (T_C). It is considered that irrigation management of corn at 75% ET_C is feasible with 10% reduction of grain yield and with increased water use efficiency (WUE). The greatest WUE (1.6 g m⁻² mm⁻¹) achieved at 456 mm of water input while grain yield plateaued at less than 600 mm. The result demonstrates that ET_C-based irrigation can be one of the efficient water delivery schemes. The results also demonstrate that grain yield reduction of corn is qualitatively describable using the variables of RWC and T_C. Therefore, it appears that water status can be monitored with measurement of the variables, promising future development of real-time irrigation scheduling.     

Differences in water use efficiency among annual forages used by the dairy industry under optimum and deficit irrigation

The increasing cost and scarcity of water for irrigation is placing pressure on Australian dairy farmers to utilize water more efficiently, and as result, water use efficiency (WUE) of forages is becoming an important criterion for sustainable dairy production. This study was conducted to identify more water use efficient forage species than the dominant dairy forage, perennial ryegrass (Lolium perenne L.). Seventeen annual forage species were investigated under optimum irrigation (I1) and two deficit irrigation treatments (nominally 66 and 33% of irrigation water applied to the optimal level), over 3 years at Camden, NSW, on a brown Dermsol in a warm temperate climate. Forages with the highest yield generally had the highest WUE_t (total yield/evapotranspiration). Under optimal irrigation, there was a three-fold difference in mean annual WUE_t between forages, with maize (Zea mays L.) having the highest (42.9 kg ha⁻¹ mm⁻¹) and cowpea (Vigna unguiculata (L.) Walp.) the lowest (13.5 kg ha⁻¹ mm⁻¹), with 11 of the forage species having a greater WUE_t than perennial ryegrass. The ‘harvested’ forages maize, wheat, triticale (Triticosecale rimpaui Wittm.) and maple pea (Pisum sativium L.) generally had higher mean WUE_t (26.7-42.9 kg ha⁻¹ mm⁻¹) than the remaining forages which were defoliated multiple times to simulate grazing (13.5-30.1 kg ha⁻¹ mm⁻¹). The reduction in annual WUE_t in response to deficit irrigation was greatest for the warm season forages with up to 30% reduction for maize, while most of the cool season annuals were not significantly affected by deficit irrigation at the levels imposed. In order to maximize WUE_t of any forage, it is necessary to maximize yield, as there is a strong positive relationship between yield and WUE_t. However, while WUE_t is an important criterion for choosing dairy forages, it is only one factor in a complex system. Choice of forages must be considered on a whole farm basis and include consideration of yield, nutritive value, cost of production and risk.     

Irrigation with coalbed natural gas co-produced water

Water quality is one of the potential concerns associated with the development of coalbed natural gas (CBNG) in the Powder River Basin (PRB) of Wyoming and Montana. Large quantities of water (hereafter referred to as CBNG water) are being co-produced and often discharged in the process of exploring natural gas from coal seams. Use of CBNG water for irrigating croplands may be beneficial if factors associated with soil salinity and sodicity are controlled. This study evaluated effects of five water and three soil treatments applied to a mixed-hay cropland on selected soil chemical properties using a split plot design. Water treatments consisted of Piney Creek water (PC or control), direct irrigation with CBNG water (electrical conductivity or EC of 1.38 dS m⁻¹ and sodium adsorption ratio or SAR of 24.3 mmol^1/2 L^−1/2) with no amendments (NT), CBNG water mixed with solution grade gypsum (G), CBNG water acidified using sulfur burner and mixed with gypsum (GSB) and CBNG water mixed with Piney Creek water (PC/CBNG). Soil treatments consisted of gypsum (G), elemental sulfur (S), combination of these two (GS) and no treatment or the control (NT). Pre (Summer 2003) and post treatment (Fall 2004) soil samples were collected to a depth of 60 cm (top three horizons: A, Bt₁ and Bt₂) to evaluate the effects of treatments on soil pH, EC, SAR, and sulfate (SO₄²⁻) concentrations. Comparisons between pre and post irrigation soil chemistry data indicated CBNG water with no amendments significantly increased (P ≤ 0.05) Na⁺ concentration within the soil profile. Plots treated with a combination of the GSB water treatment and the GS soil amendments were most effective in maintaining the low SAR values at surface soil layer. In all treatment combinations, both EC and SAR increased significantly in the top two sampling depths (A and Bt₁ horizons). Further studies are required to evaluate applications of leaching fractions at the end of each irrigation season for its effectiveness at moving Na⁺ below the rooting zone.     

Different drip irrigation regimes affect cotton yield, water use efficiency and fiber quality in western Turkey

Decreasing in water availability for cotton production has forced researchers to focus on increasing water use efficiency by improving either new drought-tolerant cotton varieties or water management. A field trial was conducted to observe the effects of different drip irrigation regimes on water use efficiencies (WUE) and fiber quality parameters produced from N-84 cotton variety in the Aegean region of Turkey during 2004 and 2005. Treatments were designated as full irrigation (T₁₀₀, which received 100% of the soil water depletion) and those that received 75, 50 and 25% of the amount received by treatment T₁₀₀ on the same day (treatments T₇₅; T₅₀ and T₂₅, respectively). The average seasonal water use values ranged from 265 to 753 mm and the average seed cotton yield varied from 2550 to 5760 kg ha⁻¹. Largest average cotton yield was obtained from the full irrigation treatment (T₁₀₀). WUE ranged from 0.77 kg m⁻³ in the T₁₀₀ to 0.98 kg m⁻³ in the T₂₅ in 2004 growing season and ranged from 0.76 kg m⁻³ in the T₁₀₀ to 0.94 kg m⁻³ in the T₂₅ in 2005 growing season. The largest irrigation water use efficiency (IWUE) was observed in the T₂₅ (1.46 kg m⁻³), and the smallest IWUE was in the T₁₀₀ treatment (0.81 kg m⁻³) in the experimental years. A yield response factor (k_y) value of 0.78 was determined based on averages of two years. Leaf area index (LAI) and dry matter yields (DM) increased with increasing water use for treatments. Fiber qualities were influenced by drip irrigation levels in both years. The results revealed that well-irrigated treatments (T₁₀₀) could be used for the semi-arid climatic conditions under no water shortage. Moreover, the results also demonstrated that irrigation of cotton with drip irrigation method at 75% level (T₇₅) had significant benefits in terms of saved irrigation water and large WUE indicating a definitive advantage of deficit irrigation under limited water supply conditions. In an economic viewpoint, 25.0% saving in irrigation water (T₇₅) resulted in 34.0% reduction in the net income. However, the net income of the T₁₀₀ treatment is found to be reasonable in areas with no water shortage.     

Evapotranspiration components determined by sap flow and microlysimetry techniques of a vineyard in northwest China: Dynamics and influential factors

Large areas of vineyards have been established in recent years in arid region of northwest China, despite limited water resources. Water to support these vineyards is mainly supplied by irrigation. Accurate estimation of vineyard evapotranspiration (ET) can provide a scientific basis for developing irrigation management. Transpiration and soil evaporation, as two main components of ET, were measured separately in a vineyard in this region by heat balance sap flow system and micro-lysimeters during the growing season of 2009. Diurnal and seasonal dynamics of sap flow and its environmental controls were analyzed. Daily sap flow rate (SR_l) increased linearly with solar radiation (R_s), but showed an exponential increase to its maximum curve as a function of vapor pressure deficit (VPD). Residuals of the two regressions both depended on volumetric soil water content to a depth of 1.0 m (VWC). VWC also significantly influenced SR_l. The relationship of them could be expressed by a piecewise regression with the turnover point of VWC = 0.188 cm³ cm⁻³, which was ∼60% of the field capacity. Conversely, soil evaporation (E_s) increased exponentially with VWC. Thus, we recommended keeping VWC in such vineyards slightly above ∼60% of the field capacity to maintain transpiration while reducing soil evaporation. Vineyard transpiration (T_s) was scaled from sap flow by using leaf area (A_l) as it explained 60% of the spatial variability of sap flow. Vine transpiration was 202.0 mm during the period from April 28 to October 5; while that of E_s was 181.0 mm. The sum of these two components was very close to ET estimated by the Bowen ratio energy balance method (386.9 mm), demonstrating the applicability of sap flow for measuring grape water use in this region.     

Corn crop response under managing different irrigation and salinity levels

Non-uniformity of water distribution under irrigation system creates both deficit and surplus irrigation areas. Water salinity can be hazard on crop production; however, there is little information on the interaction of irrigation and salinity conditions on corn (Zea Mays) growth and production. This study evaluated the effect of salinity and irrigation levels on growth and yield of corn grown in the arid area of Egypt. A field experiment was conducted using corn grown in northern Egypt at Quesina, Menofia in 2009 summer season to evaluate amount of water applied, salinity hazard and their interactions. Three salinity levels and five irrigation treatments were arranged in a randomized split-plot design with salinity treatments as main plots and irrigation rates within salinity treatments. Salinity treatments were to apply fresh water (0.89 dS m⁻¹), saline water (4.73 dS m⁻¹), or mixing fresh plus saline water (2.81 dS m⁻¹). Irrigation treatments were a ratio of crop evapotranspiration (ET) as: 0.6ET, 0.8ET, 1.0ET, 1.2ET, and 1.4ET. In well-watered conditions (1.0ET), seasonal water usable by corn was 453, 423, and 380 mm for 0.89EC, 2.81EC and 4.73EC over the 122-day growing season, respectively. Soil salt accumulation was significantly increased by either irrigation salinity increase or amount decrease. But, soil infiltration was significantly decreased by either salinity level or its interaction with irrigation amount. Leaf temperature, transpiration rate, and stomata resistance were significantly affected by both irrigation and salinity levels with interaction. Leaf area index, harvest index, and yield were the greatest when fresh and adequate irrigation was applied. Grain yield was significantly affected in a linear relationship (r² ≥ 0.95) by either irrigation or salinity conditions with no interaction. An optimal irrigation scheduling was statistically developed based on crop response for a given salinity level to extrapolate data from the small experiment (uniform condition) to big field (non-uniformity condition) under the experiment constraints.     

Comparison of drip and sprinkler irrigation strategies on sunflower seed and oil yield and quality under Mediterranean climatic conditions

This study compares the effects of different irrigation regimes on seed yield and oil yield quality and water productivity of sprinkler and drip irrigated sunflower (Helianthus annus L.) on silty-clay-loam soils in 2006 and 2007 in the Mediterranean region of Turkey. In sprinkler irrigation a line-source system was used in order to create gradually varying irrigation levels. Irrigation regimes consisted of full irrigation (I₁) and three deficit irrigation treatments (I₂, I₃ and I₄), and rain-fed treatment (I₅). In the drip system, irrigation regimes included full irrigation (FI-100), three deficit irrigation treatments (DI-25, DI-50, DI-75), partial root zone drying (PRD-50) and rain-fed treatment (RF). Irrigations were scheduled at weekly intervals both in sprinkler and drip irrigation, based on soil water depletion within a 0.90 m root zone in FI-100 and I₁ plots. Irrigation treatments influenced significantly (P < 0.01) sunflower seed and oil yields, and oil quality both with sprinkler and drip systems. Seed yields decreased with increasing water stress levels under drip and sprinkler irrigation in both experimental years. Seed yield response to irrigation varied considerably due to differences in soil water contents and spring rainfall distribution in the experimental years. Although PRD-50 received about 36% less irrigation water as compared to FI-100, sunflower yield was reduced by an average of 15%. PRD-50 produced greater seed and oil yields than DI-50 in the drip irrigation system. Yield reduction was mainly due to less number of seeds per head and lower seed mass. Soil water deficits significantly reduced crop evapotranspiration (ET), which mainly depends on irrigation amounts. Significant linear relationships (R² = 0.96) between ET and oil yield (Y) were obtained in each season. The seed yield response factors (ky_seed) were 1.24 and 0.86 for the sprinkler and 1.19 and 1.06 for the drip system in 2006 and 2007, respectively. The oil yield response factor (ky_oil) for sunflower was found to be 1.08 and 1.49 for both growing seasons for the sprinkler and 1.36 and 1.25 for the drip systems, respectively. Oil content decreased with decreasing irrigation amount. Consistently greater values of oil content were obtained from the full irrigation treatment plots. The saturated (palmitic and stearic acid) and unsaturated (oleic and linoleic acid) fatty acid contents were significantly affected by water stress. Water stress caused an increase in oleic acid with a decrease in linoleic acid contents. The palmitic and stearic acid concentrations decreased under drought conditions. Water productivity (WP) values were significantly affected by irrigation amounts and ranged from 0.40 to 0.71 kg m⁻³ in 2006, and from 0.69 to 0.91 kg m⁻³ in 2007. The PRD-50 treatment resulted in the greatest WP (1.0 kg m⁻³) and irrigation water productivity (IWP) (1.4 kg m⁻³) in both growing seasons. The results revealed that under water scarcity situation, PRD-50 in drip and I₂ in sprinkler system provide acceptable irrigation strategies to increase sunflower yield and quality.