Yield and quality of melon grown under different irrigation and nitrogen rates

During 2 years, a melon crop (Cucumis melo L. cv. Sancho) was grown under field conditions to investigate the effects of different nitrogen (N) and irrigation (I) levels on fruit yield, fruit quality, irrigation water use efficiency (IWUE) and nitrogen applied efficiency (NAE). The statistical design was a split-plot with four replications, where irrigation was the main factor of variation and N was the secondary factor. In 2005, irrigation treatments consisted of applying daily a moderate water stress equivalent to 75% of ETc (crop evapotranspiration), a 100% ETc control and an excess irrigation of 125% ETc (designated as I₇₅, I₁₀₀ and I₁₂₅), while the N treatments were 30, 85, 112 and 139 kg N ha⁻¹ (designated as N₃₀, N₈₅, N₁₁₂ and N₁₃₉). In 2006, both the irrigation and N treatments applied were: 60, 100 and 140% ETc (I₆₀, I₁₀₀ and I₁₄₀) and 93, 243 and 393 kg N ha⁻¹ (N₉₃, N₂₄₃ and N₃₉₃). Moderate water stress did not reduce melon yield and high IWUE was obtained. Under severe deficit irrigation, the yield was reduced by 22% mainly due to decrease fruit weight. The relative yield (yield/maximum yield) was higher than 95% when the irrigation depth applied was in the range of 87-136% ETc. In 2006, the interaction between irrigation and N was significant for yield, fruit weight and IWUE. The best yield, 41.3 Mg ha⁻¹, was obtained with 100% ETc at N₉₃. The flesh firmness and the placenta and seeds weight increased when the irrigation level was reduced by 60% ETc. The highest NAE was obtained with quantities of water close to 100% ETc and increased as the N level was reduced. The highest IWUE was obtained with applications close to 90 kg N ha⁻¹. The I₂₄₃ and I₃₉₃ treatments produced inferior fruits due to higher skin ratios and lower flesh ratios. These results suggest that it is possible to apply moderate deficit irrigation, around 90% ETc, and reduce nitrogen input to 90 kg ha⁻¹ without lessening quality and yields.     

Nitrate leaching in a silage maize field under different irrigation and nitrogen fertilizer rates

Quantification of the interactive effects of nitrogen (N) and water on nitrate (NO₃) loss provides an important insight for more effective N and water management. The goal of this study was to evaluate the effect of different irrigation and nitrogen fertilizer levels on nitrate-nitrogen (NO₃-N) leaching in a silage maize field. The experiment included four irrigation levels (0.7, 0.85, 1.0, and 1.13 of soil moisture depletion, SMD) and three N fertilization levels (0, 142, and 189 kg N ha⁻¹), with three replications. Ceramic suction cups were used to extract soil solution at 30 and 60 cm soil depths for all 36 experimental plots. Soil NO₃-N content of 0-30 and 30-60-cm layers were evaluated at planting and harvest maturity. Total N uptake (NU) by the crop was also determined. Maximum NO₃-N leaching out of the 60-cm soil layer was 8.43 kg N ha⁻¹, for the 142 kg N ha⁻¹ and over irrigation (1.13 SMD) treatment. The minimum and maximum seasonal average NO₃ concentration at the 60 cm depth was 46 and 138 mg l⁻¹, respectively. Based on our findings, it is possible to control NO₃ leaching out of the root zone during the growing season with a proper combination of irrigation and fertilizer management.     

Simulation of bromide and nitrate leaching under heavy rainfall and high-intensity irrigation rates in North China Plain

Heavy rainfall and irrigations during the summer months in the North China Plain may cause losses of nitrogen because of nitrate leaching. The objectives of this study were to characterize the leaching of accumulated N in soil profiles, and to determine the usefulness of Br⁻ as a tracer of surface-applied N fertilizer under heavy rainfall and high irrigation rates. A field experiment with bare plots was conducted near Beijing from 5 July to 6 September 2006. The experiment included three treatments: no irrigation (rainfall only, I0), farmers’ practice irrigation (rainfall plus 100 mm irrigation, I100) and high-intensity irrigation (rainfall plus 500 mm irrigation, I500), with three replicates. Transport of surface-applied Br⁻ and NO₃⁻ (assuming no initial NO₃⁻ in the soil profile) and accumulated NO₃⁻ in soil profiles were all simulated with the HYDRUS-1D model. The model simulation results showed that Br⁻ leached through the soil profile faster than NO₃⁻. When Br⁻ was used as a tracer for surface-applied N fertilizer to estimate nitrate leaching losses, the amount of N leaching may be overestimated by about 10%. Water drainage and nitrate leaching were dramatically increased as the irrigation rate was increased. The amounts of N leaching out of the 2.1-m soil profile under I0, I100 and I500 treatments were 195 ± 84, 392 ± 136 and 612 ± 211 kg N ha⁻¹, equivalent to about 20 ± 5%, 40 ± 6% and 62 ± 7% of the accumulative N in the soil profile, respectively. N was leached more deeply as the irrigation rate increased. The larger amount of initial accumulated N was in soil profile, the higher percentage of N leaching was. N leaching was also simulated in summer under different weather conditions from 1986 to 2006. The results indicated that nitrate leaching in rainy years were significantly higher than those in dry and normal years. Increasing the irrigation times and decreasing the single irrigation rate after fertilizer application should be recommended.     

Carbon and nitrogen cycling in a tropical Brazilian soil cropped with sugarcane and irrigated with wastewater

Carbon (C) and nitrogen (N) dynamics in agro-systems can be altered as a consequence of treated sewage effluent (TSE) irrigation. The present study evaluated the effects of TSE irrigation over 16 months on N concentrations in sugarcane (leaves, stalks and juice), total soil carbon (TC), total soil nitrogen (TN), NO₃⁻-N in soil and nitrate (NO₃⁻) and dissolved organic carbon (DOC) in soil solution. The soil was classified as an Oxisol and samplings were carried out during the first productive crop cycle, from February 2005 (before planting) to September 2006 (after sugarcane harvest and 16 months of TSE irrigation). The experiment was arranged in a complete block design with five treatments and four replicates. Irrigated plots received 50% of the recommended mineral N fertilization and 100% (T100), 125% (T125), 150% (T150) and 200% (T200) of crop water demand. No mineral N and irrigation were applied to the control plots. TSE irrigation enhanced sugarcane yield but resulted in total-N inputs (804-1622 kg N ha⁻¹) greater than exported N (463-597 kg N ha⁻¹). Hence, throughout the irrigation period, high NO₃⁻ concentrations (up to 388 mg L⁻¹ at T200) and DOC (up to 142 mg L⁻¹ at T100) were measured in soil solution below the root zone, indicating the potential of groundwater contamination. TSE irrigation did not change soil TC and TN.     

Nutrient management adaptation for dryland maize yields and water use efficiency to long-term rainfall variability in China

Rainfed crop production in northern China is constrained by low and variable rainfall, and by improper management practices. This study explored both the impact of long-term rainfall variability and the long-term effects of various combinations of maize stover, cattle manure and mineral fertiliser (NP) applications on maize (Zea mays L.) yields and water use efficiency (WUE) under reduced tillage practices, at Shouyang Dryland Farming Experimental Station in northern China from 1993 onwards. The experiment was set up according to an incomplete, optimal design, with 3 factors at five levels and 12 treatments including a control with two replications. Grain yields were greatly influenced by the amount of rain during the growing season, and by soil water at sowing. Annual mean grain yields ranged from 3 to 10 t ha⁻¹ and treatment mean yields from 4.2 to 7.2 t ha⁻¹. The WUE ranged from 40 in treatments with balanced nutrient inputs in dry (weather/or soil) years to 6.5 kg ha⁻¹ mm⁻¹ for the control treatments in wet years. The WUE averaged over the 15-year period ranged from 11 to 19 kg ha⁻¹ mm⁻¹. Balanced combination of stover (3000-6000 kg), manure (1500-6000 kg) and N fertiliser (105 kg) gave the highest yield and hence WUE. It is suggested that 100 kg N per ha should be a best choice, to be adapted according to availability of stover and manure. Possible management options under variable rainfall conditions to alleviate occurring moisture stress for crops must be tailored to the rainfall pattern. The potentials of split applications, targeted to the need of the growing crop (response nutrient management), should be explored to further improve grain yield and WUE.     

Macromanagement of deficit-irrigated peanut with sprinkler irrigation

Precision irrigation management and scheduling, as well as developing site- and cultivar-specific crop coefficient (K_c), and yield response factor to water deficit (ky) are very important parameters for efficient use of limited water resources. This study investigated the effect of deficit irrigation, applied at different growth stages of peanut with sprinkler irrigation in sandy soil, on field peanut evapotranspiration (ETc), yield and yield components, and water use efficiencies (IWUE and WUE). Also, yield response factor to water deficit (ky), and site- and cultivar-specific K_c were developed. Four treatments were imposed to deficit irrigation during late vegetative and early flowering, late flowering and early pegging, pegging, and pod formation growth stages of peanut, and compared with full irrigation in the course of the season (control). A soil water balance equation was used to estimate crop evapotranspiration (ETc). The results revealed that maximum seasonal ETc was 488 mm recorded with full irrigation treatment. The maximum value of K_c (0.96) occurred at the fifth week after sowing, this value was less than the generic values listed in FAO-33 and -56 (1.03 and 1.15), respectively. Dry kernels yield among treatments differed by 41.4%. Deficit irrigation significantly affected yields, where kernels yield decreased by 28, 39, 36, and 41% in deficit-irrigated late vegetative and early flowering, late flowering and early pegging, pegging, and pod formation growth stages, respectively, compared with full irrigation treatment. Peanut yields increased linearly with seasonal ETc (R² = 0.94) and ETc/ETp (R² = 0.92) (ETp = ETc with no water stress). The yield response factor (ky), which indicates the relative reduction in yield to relative reduction in ETc, averaged 2.9, was higher than the 0.7 value reported by Doorenbos and Kassam [Doorenbos, J., Kassam, A.H., 1979. Yield response to water. FAO Irrigation and Drainage Paper 33, Rome, Italy, 193 pp.], the high ky value reflects the great sensitivity of peanut (cv. Giza 5) to water deficit. WUE values varied considerably with deficit irrigation treatments, averaging 6.1 and 4.5 kg ha⁻¹ mm⁻¹ (dry-mass basis) for pods and kernels, respectively. Differences in WUE between the driest and wettest treatment were 31.3 and 31.3% for pods and kernels, respectively. Deficit irrigation treatments, however, impacted IWUE much more than WUE. Differences in IWUE between the driest and wettest treatment were 33.9 and 33.9% for pods and kernels, respectively. The results revealed that better management of available soil water in the root zone in the course of the season, as well as daily and seasonal accurate estimation of ETc can be an effective way for best irrigation scheduling and water allocation, maximizing yield, and optimizing economic return.     

Simulation of transpiration, drainage, N uptake, nitrate leaching, and N uptake concentration in tomato grown in open substrate

Free-drainage or “open” substrate system used for vegetable production in greenhouses is associated with appreciable NO₃⁻ leaching losses and drainage volumes. Simulation models of crop N uptake, N leaching, water use and drainage of crops in these systems will be useful for crop and water resource management, and environmental assessment. This work (i) modified the TOMGRO model to simulate N uptake for tomato grown in greenhouses in SE Spain, (ii) modified the PrHo model to simulate transpiration of tomato grown in substrate and (iii) developed an aggregated model combining TOMGRO and PrHo to calculate N uptake concentrations and drainage NO₃⁻ concentration. The component models simulate NO₃⁻-N leached by subtracting simulated N uptake from measured applied N, and drainage by subtracting simulated transpiration from measured irrigation. Three tomato crops grown sequentially in free-draining rock wool in a plastic greenhouse were used for calibration and validation. Measured daily transpiration was determined by the water balance method from daily measurements of irrigation and drainage. Measured N uptake was determined by N balance, using data of volumes and of concentrations of NO₃⁻ and NH₄⁺ in applied nutrient solution and drainage. Accuracy of the two modified component models and aggregated model was assessed by comparing simulated to measured values using linear regression analysis, comparison of slope and intercept values of regression equations, and root mean squared error (RMSE) values. For the three crops, the modified TOMGRO provided accurate simulations of cumulative crop N uptake, (RMSE = 6.4, 1.9 and 2.6% of total N uptake) and NO₃⁻-N leached (RMSE = 11.0, 10.3, and 6.1% of total NO₃⁻-N leached). The modified PrHo provided accurate simulation of cumulative transpiration (RMSE = 4.3, 1.7 and 2.4% of total transpiration) and cumulative drainage (RMSE = 13.8, 6.9, 7.4% of total drainage). For the four cumulative parameters, slopes and intercepts of the linear regressions were mostly not statistically significant (P < 0.05) from one and zero, respectively, and coefficient of determination (r²) values were 0.96-0.98. Simulated values of total drainage volumes for the three crops were +21, +1 and −13% of measured total drainage volumes. The aggregated TOMGRO-PrHo model generally provided accurate simulation of crop N uptake concentration after 30-40 days of transplanting, with an average RMSE of approximately 2 mmol L⁻¹. Simulated values of average NO₃⁻ concentration in drainage, obtained with the aggregated model, were −7, +18 and +31% of measured values.     

Tomato nitrogen accumulation and fertilizer use efficiency on a sandy soil, as affected by nitrogen rate and irrigation scheduling

Tomato production systems in Florida are typically intensively managed with high inputs of fertilizer and irrigation and on sandy soils with low inherent water and nutrient retention capacities; potential nutrient leaching losses undermine the sustainability of such systems. The objectives of this 3-year field study were to evaluate the interaction between N-fertilizer rates and irrigation scheduling on crop N and P accumulation, N-fertilizer use efficiency (NUE) and NO₃-N leaching of tomato cultivated in a plastic mulched/drip irrigated production system in sandy soils. Experimental treatments were a factorial combination of three irrigation scheduling regimes and three N-rates (176, 220, and 330 kg ha⁻¹). Irrigation treatments included were: (1) surface drip irrigation (SUR) both the irrigation and fertigation line placed underneath the plastic mulch; (2) subsurface drip irrigation (SDI) where the irrigation drip was placed 0.15 m below the fertigation line which was located on top of the bed; and (3) TIME (conventional control) with the irrigation and fertigation lines placed as in SUR and irrigation applied once a day. Except for the TIME treatment all irrigation treatments were soil moisture sensor (SMS)-based with irrigation occurring at 10% volumetric water content. Five irrigation windows were scheduled daily and events were bypassed if the soil water content exceeded the established threshold. The use of SMS-based irrigation systems significantly reduced irrigation water use, volume percolated, and nitrate leaching. Based on soil electrical conductivity (EC) readings, there was no interaction between irrigation and N-rate treatments on the movement of fertilizer solutes. Total plant N accumulation for SUR and SDI was 12-37% higher than TIME. Plant P accumulation was not affected by either irrigation or N-rate treatments. The nitrogen use efficiency for SUR and SDI was on the order of 37-45%, 56-61%, and 61-68% for 2005, 2006 and 2007, respectively and significantly higher than for the conventional control system (TIME). Moreover, at the intermediate N-rate SUR and SDI systems reduced NO₃-N leaching to 5 and 35 kg ha⁻¹, while at the highest N-rate corresponding values were 7 and 56 kg N ha⁻¹. Use of N application rates above 220 kg ha⁻¹ did not result in fruit and/or shoot biomass nor N accumulation benefits, but substantially increased NO₃-N leaching for the control treatment, as detected by EC monitoring and by the lysimeters. It is concluded that appropriate use of SDI and/or sensor-based irrigation systems can sustain high yields while reducing irrigation application as well as reducing NO₃-N leaching in low water holding capacity soils.     

Forage quality, water use and nitrogen utilization efficiencies of pearl millet (Pennisetum americanum L.) grown under different soil moisture and nitrogen levels

The increasing scarcity of water for irrigation is becoming the most important problem for producing forage in all arid and semi-arid regions. Pearl millet is a key crop in these regions which needs relatively less water than other crops. In this research, a field study was conducted to identify the best combination of irrigation and nitrogen (N) management to achieve acceptable pearl millet forage both in quantity and quality aspects. Pearl millet was subjected to four irrigation treatments with interaction of N fertilizer (0, 75, 150 and 225 kg ha⁻¹). The irrigation treatments were 40%, 60%, 80% and 100% of total available soil water (I₄₀, I₆₀, I₈₀ and I₁₀₀, respectively). The results showed that increasing moisture stress (from I₄₀ to I₁₀₀) resulted in progressively less total dry matter (TDM), leaf area index (LAI), and nitrogen utilization efficiency (NUzE), while water use efficiency (WUE) and the percentage of crude protein (CP%) increased. The highest TDM and LAI were found to be 21.45 t ha⁻¹ and 8.65, in I₄₀ treatment, respectively. TDM, WUE, CP% and profit responses to N rates were positive. The maximum WUE of 4.19 kg DM/m³ was achieved at I₁₀₀ with 150 kg N ha⁻¹. The results of this research indicate that the maximum profit of forage production was obtained in plots which were fully irrigated (I₄₀) and received 225 kg N ha⁻¹. However, in the situation which water is often limited and not available, application of 150 kg N ha⁻¹ can produce high forage quality and guaranty acceptable benefits for farmers.     

Using EPIC model to manage irrigated cotton and maize

Simulation models are becoming of interest as a decision support system for management and assessment of crop water use and of crop production. The Environmental Policy Integrated Climate (EPIC) model was used to evaluate its application as a decision support tool for irrigation management of cotton and maize under South Texas conditions. Simulation of the model was performed to determine crop yield, crop water use, and the relationships between the yield and crop water use parameters such as crop evapotranspiration (ETc) and water use efficiency (WUE). We measured actual ETc using a weighing lysimeter and crop yields by field sampling, and then calibrated the model. The measured variables were compared with simulated variables using EPIC. Simulated ETc agreed with the lysimeter, in general, but some simulated ETc were biased compared with measured ETc. EPIC also simulated the variability in crop yields at different irrigation regimes. Furthermore, EPIC was used to simulate yield responses at various irrigation regimes with farm fields’ data. Maize required ∼700 mm of water input and ∼650 mm of ETc to achieve a maximum yield of 8.5 Mg ha⁻¹ while cotton required between 700 and 900 mm of water input and between 650 and 750 mm of ETc to achieve a maximum yield of 2.0-2.5 Mg ha⁻¹. The simulation results demonstrate that the EPIC model can be used as a decision support tool for the crops under full and deficit irrigation conditions in South Texas. EPIC appears to be effective in making long-term and pre-season decisions for irrigation management of crops, while reference ET and phenologically based crop coefficients can be used for in-season irrigation management.     

Subsurface drip irrigation of onions: Effects of drip tape emitter spacing on yield and quality

Improved irrigation water use efficiency is an important component of sustainable agricultural production. Efficient water delivery systems such as subsurface drip irrigation (SDI) can contribute immensely towards improving crop water use efficiency and conserving water. However, critical management considerations such as choice of SDI tube, emitter spacing and installation depth are necessary to attain improved irrigation efficiencies and production benefits. In this study, we evaluated the effects of subsurface drip tape emitter spacing (15, 20 and 30 cm) on yield and quality of sweet onions grown at two locations in South Texas—Weslaco and Los Ebanos. Season-long cumulative crop evapotranspiration (ETc) was 513 mm in Weslaco and 407 mm at Los Ebanos. Total crop water input (rain + irrigation) at Weslaco was roughly equal to ETc (92% ETc) whereas at Los Ebanos, water inputs exceeded ETc by about 35%. Onion yields ranged from 58.5 to 70.3 t ha⁻¹ but were not affected by drip tube emitter spacing. Onion pungency (pyruvic acid development) and soluble solids concentration were also not significantly influenced by treatments. Crop water use efficiency was slightly higher at Weslaco (13.7 kg/m³) than at Los Ebanos (11.7 kg/m³) partly because of differences in total water inputs resulting from differences in irrigation management. The absence of any significant effects of drip tape emitter spacing on onion yield may be due to the fact that irrigation was managed to provide roughly similar irrigation amounts and optimum soil moisture conditions in all treatments.     

Tuber yield, water and fertilizer productivity in early potato as affected by a combination of irrigation and fertilization

Excessive amounts of irrigation water and fertilizers are often utilized for early potato cultivation in the Mediterranean basin. Given that water is expensive and limited in the semi-arid areas and that fertilizers above a threshold level often prove inefficacious for production purposes but still risk nitrate and phosphorous pollution of groundwater, it is crucial to provide an adequate irrigation and fertilization management. With the aim of achieving an appropriate combination of irrigation water and nutrient application in cultivation management of a potato crop in a Mediterranean environment, a 2-year experiment was conducted in Sicily (South Italy). The combined effects of 3 levels of irrigation (irrigation only at plant emergence, 50% and 100% of the maximum evapotranspiration - ETM) and 3 levels of mineral fertilization (low: 50, 25 and 75 kg ha⁻¹, medium: 100, 50 and 150 kg ha⁻¹ and high: 300, 100 and 450 kg ha⁻¹ of N, P₂O₅ and K₂O) were studied on the tuber yield and yield components, on both water irrigation and fertilizer productivity and on the plant source/sink (canopy/tubers dry weight) ratio. The results show a marked interaction between level of irrigation and level of fertilization on tuber yield, on Irrigation Water Productivity and on fertilizer productivity of the potato crop. We found that the treatments based on 50% ETM and a medium level of fertilization represent a valid compromise in early potato cultivation management. Compared to the high combination levels of irrigation and fertilization, this treatment entails a negligible reduction in tuber yield to save 90 mm ha⁻¹ year⁻¹ of irrigation water and 200, 50 and 300 kg ha⁻¹ year⁻¹ of N, P₂O₅ and K₂O, respectively, with notable economic savings for farmers compared to the spendings that are usually made.     

Identification of nitrate leaching hot spots in a large area with contrasting soil texture and management

Identification of nitrate (NO₃) leaching hot spots is important in mitigating environmental effect of NO₃. Once identified, the hot spots can be further analyzed in detail for evaluating appropriate alternative management techniques to reduce impact of nitrate on groundwater. This study was conducted to identify NO₃ leaching hot spots in an approximately 36,000 ha area in Serik plain, which is used intensively for agriculture in the Antalya region of Southern Turkey. Geo-referenced water samples were taken from 161 wells and from the representative soils around the wells during the period from late May to early June of 2009. The data were analyzed by classical statistics and geostatistics. Both soil and groundwater NO₃-N concentrations demonstrated a considerably high variation, with a mean of 10.2 mg kg⁻¹ and 2.1 mg L⁻¹ NO₃-N for soil and groundwater, respectively. The NO₃-N concentrations ranged from 0.01 to 102.5 mg L⁻¹ in well waters and from 1.89 to 106.4 mg kg⁻¹ in soils. Nitrate leaching was spatially dependent in the study area. Six hot spots were identified in the plain, and in general, the hot spots coincided with high water table, high sand content, and irrigated wheat and cotton. The adverse effects of NO₃ can be mitigated by switching the surface and furrow irrigation methods to sprinkler irrigation, which results in a more efficient N and water use. Computer models such as NLEAP can be used to analyze alternative management practices together with soil, aquifer, and climate characteristics to determine a set of management alternatives to mitigate NO₃ effect in these hot spot areas.     

Energy requirements for transport and surface application of liquid pig manure in Manitoba,Canada

The objective of this study was to conduct a thorough accounting of energy used to transport liquid pig manure from farm storage to the field and to surface-apply the manure. Energy consumption was determined using both energy data from the literature plus data from field-scale research. Energy consumption was compared between two manure application systems (the drag hose and the slurry wagon systems) and two application timing treatments (single vs. twice-annual manure application). The single annual application of liquid pig manure applied at 81.5 m³ ha⁻¹ and transported 1.8 km from storage to field consumed 2180 MJ ha⁻¹ with the drag hose system and 2185 MJ ha⁻¹ with the slurry wagon system. The twice-annual manure application regime used 2726 and 2209 MJ ha⁻¹ for the drag hose and slurry wagon systems, respectively. When energy use was calculated on the basis of MJ per kg of available N, liquid pig manure applied once annually with the slurry wagon system provided N at 17.76 MJ kg⁻¹ of available N, which was 33% of the energy cost of N from anhydrous ammonia and 23% of the energy cost of N from urea. Manure transport distance could be increased to 8.4 km before the energy cost per kg of available N from pig manure was equivalent to anhydrous ammonia, and up to 12.3 km before the energy cost of manure N was equivalent to urea N. Despite the high energy cost to deliver liquid pig manure from storage to field, the much lower cost per kg of available N compared to inorganic fertilizer N highlights the opportunities that exist for improving the energy efficiency of industrial agriculture by replacing inorganic fertilizers with manure.     

Yield and water-production functions of two durum wheat cultivars grown under different irrigation and nitrogen regimes

Wheat (Triticum durum L.) yields in the semi-arid regions are limited by inadequate water supply late in the cropping season. Planning suitable irrigation strategy and nitrogen fertilization with the appropriate crop phenology will produce optimum grain yields. A 3-year experiment was conducted on deep, fairly drained clay soil, at Tal Amara Research Station in the central Bekaa Valley of Lebanon to investigate the response of durum wheat to supplemental irrigation (IRR) and nitrogen rate (NR). Three water supply levels (rainfed and two treatments irrigated at half and full soil water deficit) were coupled with three N fertilization rates (100, 150 and 200 kg N ha⁻¹) and two cultivars (Waha and Haurani) under the same cropping practices (sowing date, seeding rate, row space and seeding depth). Averaged across N treatments and years, rainfed treatment yielded 3.49 Mg ha⁻¹ and it was 25% and 28% less than half and full irrigation treatments, respectively, for Waha, while for Haurani the rainfed treatment yielded 3.21 Mg ha⁻¹, and it was 18% and 22% less than half and full irrigation, respectively. On the other hand, N fertilization of 150 and 200 kg N ha⁻¹ increased grain yield in Waha by 12% and 16%, respectively, in comparison with N fertilization of 100 kg N ha⁻¹, while for cultivar Haurani the increases were 24% and 38%, respectively. Regardless of cultivar, results showed that supplemental irrigation significantly increased grain number per square meter and grain weight with respect to the rainfed treatment, while nitrogen fertilization was observed to have significant effects only on grain number per square meter. Moreover, results showed that grain yield for cultivar Haurani was less affected by supplemental irrigation and more affected by nitrogen fertilization than cultivar Waha in all years. However, cultivar effects were of lower magnitude compared with those of irrigation and nitrogen. We conclude that optimum yield was produced for both cultivars at 50% of soil water deficit as supplemental irrigation and N rate of 150 kg N ha⁻¹. However, Harvest index (HI) and water use efficiency (WUE) in both cultivars were not significantly affected neither by supplemental irrigation nor by nitrogen rate. Evapotranspiration (ET) of rainfed wheat ranged from 300 to 400 mm, while irrigated wheat had seasonal ET ranging from 450 to 650 mm. On the other hand, irrigation treatments significantly affected ET after normalizing for vapor pressure deficit (ET/VPD) during the growing season. Supplemental irrigation at 50% and 100% of soil water deficit had approximately 26 and 52 mm mbar⁻¹ more ET/VPD, respectively, than those grown under rainfed conditions.     

Evapotranspiration and water use of full and deficit irrigated cotton in the Mediterranean environment in northern Syria

Cotton (Gossypium hirsutum L.) is the most important industrial and summer cash crop in Syria and many other countries in the arid areas but there are concerns about future production levels, given the high water requirements and the decline in water availability. Most farmers in Syria aim to maximize yield per unit of land regardless of the quantity of water applied. Water losses can be reduced and water productivity (yield per unit of water consumed) improved by applying deficit irrigation, but this requires a better understanding of crop response to various levels of water stress. This paper presents results from a 3-year study (2004-2006) conducted in northern Syria to quantify cotton yield response to different levels of water and fertilizer. The experiment included four irrigation levels and three levels of nitrogen (N) fertilizer under drip irrigation. The overall mean cotton (lint plus seed, or lintseed) yield was 2502 kg ha⁻¹, ranging from 1520 kg ha⁻¹ under 40% irrigation to 3460 kg ha⁻¹ under 100% irrigation. Mean water productivity (WP_ET) was 0.36 kg lintseed per m³ of crop actual evapotranspiration (ET_c), ranging from 0.32 kg m⁻³ under 40% irrigation to 0.39 kg m⁻³ under the 100% treatment. Results suggest that deficit irrigation does not improve biological water productivity of drip-irrigated cotton. Water and fertilizer levels (especially the former) have significant effects on yield, crop growth and WP_ET. Water, but not N level, has a highly significant effect on crop ET_c. The study provides production functions relating cotton yield to ET_c as well as soil water content at planting. These functions are useful for irrigation optimization and for forecasting the impact of water rationing and drought on regional water budgets and agricultural economies. The WP_ET values obtained in this study compare well with those reported from the southwestern USA, Argentina and other developed cotton producing regions. Most importantly, these WP_ET values are double the current values in Syria, suggesting that improved irrigation water and system management can improve WP_ET, and thus enhance conservation and sustainability in this water-scarce region.     

Seasonal on-farm irrigation performance in the Ebro basin (Spain): Crops and irrigation systems

Irrigation performance assessments are required for hydrological planning and as a first step to improve water management. The objective of this work was to assess seasonal on-farm irrigation performance in the Ebro basin of Spain (0.8 million ha of irrigated land). The study was designed to address the differences between crops and irrigation systems using irrigation district data. Information was only available in districts located in large irrigation projects, accounting for 58% of the irrigated area in the basin. A total of 1617 records of plot water application (covering 10,475 ha) were obtained in the basin. Average net irrigation requirements (IR_n) ranged from 2683 m³ ha⁻¹ in regulated deficit irrigation (RDI) vineyards to 9517 m³ ha⁻¹ in rice. Average irrigation water application ranged from 1491 m³ ha⁻¹ in vineyards to 11,404 m³ ha⁻¹ in rice. The annual relative irrigation supply index (ARIS) showed an overall average of 1.08. Variability in ARIS was large, with an overall standard deviation of 0.40. Crop ARIS ranged between 0.46 and 1.30. Regarding irrigation systems, surface, solid-set sprinkler and drip irrigated plots presented average ARIS values of 1.41, 1.16 and 0.65, respectively. Technical and economic water productivities were determined for the main crops and irrigation systems in the Aragón region. Rice and sunflower showed the lowest productivities. Under the local technological and economic constraints, farmers use water cautiously and obtain reasonable (yet very variable) productivities.     

Annual carbon and nitrogen loadings for a furrow-irrigated field

Evaluations of agricultural management practices for soil C sequestration have largely focused on practices, such as reduced tillage or compost/manure applications, that minimize soil respiration and/or maximize C input, thereby enhancing soil C stabilization. Other management practices that impact carbon cycling in agricultural systems, such as irrigation, are much less understood. As part of a larger C sequestration project that focused on potential of C sequestration for standard and minimum tillage systems of irrigated crops, the effects of furrow irrigation on the field C and N loading were evaluated. Experiments were conducted on a laser-leveled 30 ha grower's field in the Sacramento valley near Winters, CA. For the 2005 calendar year, water inflow and runoff was measured for all rainfall and irrigation events. Samples were analyzed for C and N associated with both sediment and dissolved fractions. Total C and N loads in the sediment were always higher in the incoming irrigation water than field runoff. Winter storms moved little sediment, but removed substantial amounts of dissolved organic carbon (DOC), or about one-third of the total C balance. Despite high DOC loads in runoff, the large volumes of applied irrigation water with sediment and DOC resulted in a net increase in total C for most irrigation events. The combined net C input and N loss to the field, as computed from the field water balance, was 30.8 kg C ha⁻¹ yr⁻¹ and 5.4 kg N ha⁻¹ yr⁻¹ for the 2005 calendar year. It is concluded that transport of C and N by irrigation and runoff water should be considered when estimating the annual C field balance and sequestration potential of irrigated agro-ecosystems.     

Response of cotton to various levels of nitrogen and water applied to normal and paired sown cotton under drip irrigation in relation to check-basin

Field experiments were conducted for 2 years to investigate the effects of various levels of nitrogen (N) and methods of cotton planting on yield, agronomic efficiency of N (AEN) and water use efficiency (WUE) in cotton irrigated through surface drip irrigation at Bathinda situated in semi-arid region of northwest India. Three levels of N (100, 75 and 50% of recommended N, 75 kg ha⁻¹) were tested under drip irrigation in comparison to 75 kg of N ha⁻¹ in check-basin. The three methods of planting tried were; normal sowing of cotton with row to row spacing of 67.5 cm (NS), normal paired row sowing with row to row spacing of 35 and 100 cm alternately (NP) and dense paired row sowing with row to row spacing of 35 and 55 cm alternately resulting in total number rows and plants to be 1.5 times (DP) than NS and NP. In NS there was one lateral along each row, but in paired sowings there was one lateral between each pair of rows. Consequently the number of laterals and quantity of water applied was 50 and 75% in NP and DP, respectively, as compared with NS in which irrigation water applied was equivalent to check-basin.Drip irrigation under NS resulted in an increase of 258 and 453 kg ha⁻¹ seed cotton yield than check-basin during first and second year, respectively, when same quantity of water and N was applied. Drip irrigation under dense paired sowing (DP) in which the quantity of irrigation water applied was 75% as compared with NS, further increased the yield by 84 and 101 kg ha⁻¹ than NS during first and second year, respectively. Drip irrigation under NP, in which the quantity of water applied and number of laterals used were 50% as compared with drip under NS, resulted in a reduction in seed cotton yield of 257 and 112 kg ha⁻¹ than NS during first and second year, respectively. However, the yield obtained in NP under drip irrigation was equivalent to yield obtained in NS under check-basin during first year but 341 kg ha⁻¹ higher yield was obtained during second year. The decrease in N applied, irrespective of methods of planting, caused a significant decline in seed cotton yield during both the years. Water use efficiency (WUE) under drip irrigation increased from 1.648 to 1.847 and from 0.983 to 1.615 kg ha⁻¹ mm⁻¹ during first and second year, respectively, when the same quantity of N and water was applied. The WUE further increased to 2.125 and 1.788 kg ha⁻¹ mm⁻¹ under DP during first and second year, respectively. The agronomic efficiency of nitrogen was higher in drip than check-basin during both the years when equal N was applied. The WUE decreased with decrease in the rate of N applied under fertigation but reverse was true for AEN. It is evident that DP under drip irrigation resulted in higher seed cotton yield, WUE and AEN than NS and also saved 25% irrigation water as well as cost of laterals.     

Water and salt balance at irrigation scheme scale: A comprehensive approach for salinity assessment in a Saharan oasis

Salt balance methods are generally applied in the root-zone and at local scales but do not provide relevant information for salinity management at irrigation scheme scales, where there are methodological impediments. A simple salt balance model was developed at irrigation scheme and yearly time scales and applied in Fatnassa oasis (Nefzaoua, Tunisia). It accounts for input by irrigation, export by drainage and groundwater flow, and provides novel computation of the influence of biogeochemical processes and variations in the resident amount of salt for each chemical component in the soil and shallow groundwater. Impediments were overcome by limiting the depth of the system so that the resident amount of salt that remained was of the same order of magnitude as salt inputs and allowed indirect and reliable estimation of groundwater flow. Sensitivity analyses as partial derivatives of groundwater salinity were carried out according to non-reactive salt balance under steady-state assumption. These analyses enabled the magnitude of the salinization process to be foreseen as a function of hydrological changes linked to irrigation, drainage, groundwater flow and extension of the irrigated area. From a salt input of 39 Mg ha⁻¹ year⁻¹ by irrigation, 21 Mg ha⁻¹ year⁻¹ (54%) and 10 Mg ha⁻¹ year⁻¹ (26%) were exported by groundwater flow and drainage, respectively. 7 Mg ha⁻¹ year⁻¹ (18%) were removed from groundwater by geochemical processes, while a non-significant 2 Mg ha⁻¹ year⁻¹ were estimated to have been stored in the soil and shallow groundwater where the residence time was only 2.7 years. The leaching efficiency of drainage was estimated at 0.77. With a water supply of 1360 mm by irrigation and 90 mm by rainfall, drainage, groundwater flow and actual evapotranspiration were 130, 230, and 1090 mm, respectively. The current extension of date palm plantations and salinization of groundwater resources are expected to significantly increase the salinity hazard while the degradation of the drainage system is expected to be of lesser impact. The approach was successfully implemented in Fatnassa oasis and proved to be particularly relevant in small or medium irrigation schemes where groundwater fluxes are significant.