Evaluating the Mechanical Behavior of Basalt Fibers/Epoxy Composites Containing Surface-modified CaCO<Subscript>3</Subscript> Nanoparticles

Polymer matrix composites (PMCs) owing to their outstanding properties such as high strength, low weight, high thermal stability and chemical resistance are broadly utilized in various industries. In the present work, the influence of silanized CaCO₃ (S-CaCO₃) with 3-aminopropyltrimethoxysilane (3-APTMS) coupling agent at different values (0, 1, 3 and 5 wt.% with respect to the matrix) on the mechanical behavior of basalt fibers (BF)/epoxy composites was examined. BF-reinforced composites were fabricated via hand lay-up technique. Experimental results from three-point bending and tensile tests showed that with the dispersion of 3 wt.% S-CaCO₃, flexural strength, flexural modulus, tensile strength and tensile modulus enhanced by 28 %, 35 %, 20 % and 30 %, respectively. Microscopic examinations revealed that the development of the mechanical properties of fibrous composites with the incorporation of modified CaCO₃ was related to enhancement in the load transfer between the nanocomposite matrix and BF as well as enhanced mechanical properties of the matrix part.     

Thermal and mechanical properties of modified CaCO3 filled poly (ethylene terephthalate) nanocomposites

Poly(ethylene terephthalate) (PET)/CaCO₃ and PET/modified-CaCO₃ (m-CaCO₃) nanocomposites were prepared by melt blending. The morphology indicated that m-CaCO₃ produced by reacting sodium oxalate and calcium chloride, was well dispersed in PET matrix and showed good interfacial interaction with PET compared to CaCO₃. No significant differences in the thermal properties such as, glass transition, melting and degradation temperatures, of the nanocomposites were observed. The thermal shrinkage of PET at 120 °C was 10.8 %, while those of PET/CaCO₃ and PET/m-CaCO₃ nanocomposites were 2.9–5.2 % and 1.2–2.8 %, respectively depending on filler content. The tensile strength of PET/CaCO₃ nanocomposite decreased with CaCO₃ loading, whereas that of PET/m-CaCO₃ nanocomposites at 0.5 wt% loading showed a 17 % improvement as compared to neat PET. The storage modulus at 120 °C increased from 1660 MPa for PET to 2350 MPa for PET/CaCO₃ nanocomposite at 3 wt% loading, and 3230 MPa for PET/m-CaCO₃ nanocomposite at 1 wt% loading.     

Mechanical and machinability behaviors of woven coir fiber-reinforced polyester composite

The research on coir-polyester composites initiated the interest in the development of woven coir fiber-reinforced polyester composites. The mechanical properties of woven coir-polyester composites were evaluated as per ASTM standards and the machinability behavior was studied by conducting drilling tests in this investigation. The woven coir-polyester composites exhibited the average values of tensile, flexural and impact strength of 19.9 MPa, 31.3 MPa and 49.9 kJ/m² respectively. The effect of NaOH treatment on the improvement of mechanical properties of woven coir-polyester composites were studied in this investigation. The 40 % increase of tensile strength, 42 % increase of flexural strength and 20 % increase of impact strength were achieved by treated woven coir fiber-reinforced polyester composites. The regression models for predicting thrust force, torque and tool wear in drilling of woven coir-polyester composites were developed and the effect of drilling parameters were analyzed.     

Preparation and characterization of glass fiber-coir hybrid composites by a novel and facile Prepreg/Press process

The present study explored the preparation of glass fiber-coir reinforced unsaturated polyester resin hybrid (GCU) composites with a novel Prepreg/Press fabrication process. Flexural, impact and thermal-mechanical properties of GCU composites were investigated. Coir reinforced unsaturated polyester resin (CU) composites was also prepared with the same process to explore the enhancement effect of glass fabric on the mechanical properties of coir-based composites. The effect of fabrication pressure on the mechanical properties of CU and GCU composites was examined. Micromorphology and interfacial reaction of the composites were analyzed. It is shown that GCU composites fabricated with the Prepreg/Press process have excellent flexural strength (185.0 MPa), MOE (18.3 GPa), and impact strength (67.2 kJ/m²). The mechanical properties of GCU composites increased with the increase of applied pressure up to 0.8 MPa in the Prepreg/Press process. However, further increase of applied pressure led to the decrease in mechanical properties. The addition of glass fabrics to GCU composites showed 419 % improvement in flexural strength, 708 % improvement in MOE and 562 % improvement in impact strength over coir-based composites. The micromorphology study proved that the poor interfacial bonding between coir and matrix led to the low mechanical properties of coir-based composites.     

Fabrication and characterization of nano Al<Subscript>2</Subscript>O<Subscript>3</Subscript> filled PVA:NH<Subscript>4</Subscript>SCN electrolyte nanofibers by electrospinning

Present paper reports a method of preparing polymer composite electrolyte nanofiber mat using polyvinyl alcohol (PVA), ammonium thiocynate (NH₄SCN) salt, and aluminium oxide (Al₂O₃) nano particles based on electrospinning technique. Two-stage process of preparation of nanofibers, namely, preparation of nano particles filled PVA electrolyte gel solution followed by its electrospinning has been used. The so obtained nanofibers have been characterized by XRD, DSC, SEM, and Conductivity measurements. XRD patterns affirm the formation of nanocomposite while SEM pictures reveal formation of fibers on a nano scale format (300–800 nm). Fibers of the electrolytes are seen to be thermally stable. Ionic conductivity of electrolyte fiber is seen to improve in the presence of nano filler at room temperature with a maximum at 5.31×10⁻³ Scm⁻¹ for 4 wt% filler concentration, which is comparable to that for corresponding dried gel electrolyte films.     

Controlling the Properties of OPEFB/PLA Polymer Composite by Using Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> for Microwave Applications

Microwave-absorptive polymer composite materials provide protection against interference to communication systems caused by microwave-inducing devices. Microwave-absorptive polymer composites were prepared from polylactic acid (PLA) biocomposite blended with oil palm empty fruit bunch (OPEFB) fiber and commercial Iron oxide (Fe₂O₃) as filler using the melt-blending method. The composites characterization was carried out using the scanning electron microscopy (SEM) and X-ray diffraction (XRD) analyses. The coefficient of reflection S₁₁ and coefficient of transmission S₂₁ of the composites for various Fe₂O₃ filler percentages were determined using a rectangular waveguide in connection with microwave vector network analyser (HP/Agilent model PNA N5227). These coefficients were then used to calculate microwave-absorption properties (in decibels). XRD analysis showed that increasing amounts of reinforced material (Fe₂O₃) reduces the crystallinity of the composites. SEM data indicated that Fe₂O₃ filler ratio increased in the composites, and adhesion to the cellulose fiber grew gradually until the highest percentage of filler was added. The complex relative permittivity and relative permeability were obtained within the broad frequency range of 8–12 GHz at room temperature for various percentages of filler and were measured by the transmission/reflection method using a vector network analyser. Fe₂O₃ embedment in OPEFB/PLA was observed to have resulted in enhancing the dielectric and magnetic properties. The values of permittivity and permeability increased with increasing Fe₂O₃ filler content. Theoretical simulation studied the relation between ε′ and ε″ of the relative complex permittivity in terms of Cole-Cole dispersion law. The result indicated that the processes of Debye relaxation in Fe₂O₃/OPEFB/PLA, the unique dielectric characteristics of Fe₂O₃ cannot be accounted for by both the Debye dipolar relaxation and natural resonance. Results further showed that the material transmission, reflection, and absorption properties could be controlled by changing the percentage of Fe₂O₃ filler in the composites.     

Mechanical and Dynamic Mechanical Studies on Epoxy-Cobaltous Sulfate Polymer Hybrids

Cobaltous sulfate heptahydrate (CoSO₄·7H₂O) was incorporated as filler into diglycidyl ether of bisphenol A (DGEBA) based epoxy resin system, to prepare organic-inorganic polymer hybrid materials. Mechanical tensile studies and dynamic mechanical analysis (DMA) were carried out in order to study the static and dynamic mechanical properties of the prepared hybrid films. Mechanical tensile studies were carried out at room temperature, at a test speed of 30 mm/min. Highest tensile strength of 24.74±2.42 MPa was achieved for 4.44 wt% filler level (FL), along with an increase in the value of Young’s modulus. Storage modulus (E′), loss modulus (E″), damping factor (tan δ) were obtained by DMA studies. Glass transition temperature (T_g) was obtained for pure epoxy and filled epoxy, for various FLs varying from 0.28 wt% to 5.00 wt%. Pure epoxy showed highest T_g value compared to filled epoxy hybrids. Highest storage modulus of 9.5 GPa was obtained for 2.22 wt% FL, which also showed highest loss modulus peak. Parameters like effectiveness coefficient (C) and crosslink density were calculated from the storage modulus data. Loss modulus and tan δ curves were analyzed to study the energy dissipation properties of prepared hybrid films. Activation energy (E_a) value for glass transition was obtained from damping factor (tan δ), which showed highest E_a value of 630.5 kJmol^-1, for 4.44 wt% FL. DMA studies for various FLs were carried out at different test frequencies in order to study the changes in dynamic mechanical properties of the prepared hybrid materials with respect to frequency     

Effect of the low and radio frequency oxygen plasma treatment of jute fiber on mechanical properties of jute fiber/polyester composite

We investigated the surface modification of jute fiber by oxygen plasma treatments. Jute fibers were treated in different plasma reactors (radio frequency “RF” and low frequency “LF” plasma reactors) using O₂ for different plasma powers to increase the interface adhesion between jute fiber and polyester matrix. The influence of various plasma reactors on mechanical properties of jute fiber-reinforced polyester composites was reported. Tensile, flexure, short beam shear tests were used to determine the mechanical properties of the composites. The interlaminar shear strength increased from 11.5 MPa for the untreated jute fiber/polyester composite to 19.8 and 26.3 MPa for LF and RF oxygen plasma treated jute fiber/polyester composites, respectively. O₂ plasma treatment also improved the tensile and flexural strengths of jute fiber/ polyester composites for both plasma systems. It is clear that O₂ plasma treatment of jute fibers by using RF plasma system instead of using LF plasma system brings about greater improvement on the mechanical properties of jute/polyester composites.     

Nano-SiO2 filled rice husk/polypropylene composites: Physico-mechanical properties

In this research, reinforcing effect of hybrid filler including rice husk (RH), beech bark (BB) and nano-SiO₂, in polypropylene has been investigated. In the sample preparation, four levels of filler loading were used for waste lignocellulosic materials (55-58 wt.%) and nano-SiO₂ (0-4 wt.%). In order to increase the interphase adhesion, polypropylene grafted with maleic anhydride was added as a coupling agent to all the composites studied. The physical properties, viz. the thickness swelling and water absorption, and mechanical properties, namely, the tensile, flexural and notched Izod impact strengths, of the composites were determined. Generally, high amount of filler content in composites can lead to the reduction of interfacial adhesion between matrix polymer and filler, and it limits their applications. The results showed that while flexural properties and elongation at break were moderately improved by the increase in the amount of filler in the matrix, tensile and Izod impact strengths decreased dramatically. However, the composites had acceptable mechanical strength levels. The mechanical properties of composites filled with RH are generally greater than BB composites. The thickness swelling and water absorption of the composites increased with the increase in the filler loading, but to a negligible extent as compared with the wood-based composites and the solid woods. Nano-SiO₂ addition showed little positive effect on the mechanical properties. It can be concluded from this study that the used waste lignocellulosic materials are attractive reinforcements from the standpoint of their physico-mechanical properties.     

Ladder-Structured Polysilsesquioxane/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> Nanocomposites for Transparent Wear-Resistant Windows

As a protective layer for deformable displays, we synthesized ladder-type polysilsesquioxanes (LPSQs) containing cyclic epoxy as a curable unit. The mechanical properties after photo- and thermal-curing of LPSQs with a small amount of added Al₂O₃ nanoparticles were compared with those of the pure LPSQs. The prepared LPSQ-Al₂O₃ nanocomposites and the pure LPSQs exhibited comparable optical transparencies and thermal stabilities. In addition, the degree of conversion of the applied epoxy units in LPSQs and the resulting mechanical properties, as monitored by Fourier transform infrared spectroscopy and nanoindentation tests, indicated that the addition of nanoparticles to LPSQs moderately enhanced the epoxy conversion rate and remarkably improved the wear resistance, including hardness, after photo-/thermal-curing processes. The LPSQ-Al₂O₃ nanocomposites achieved higher wear resistance than epoxy-silica nanocomposites containing similar curable functional groups and reinforcing fillers (silica). The excellent mechanical properties of the LPSQ-Al₂O₃ nanocomposites could be attributed to three-dimensionally interconnected networks of organic-inorganic hybrid-type chemical structures in the LPSQ as well as additional reinforcement from amine-functionalized Al₂O₃ nanoparticles covalently interconnected with the LPSQ. We believe that the devised LPSQ-Al₂O₃ nanocomposites could serve effectively as a wear-resistant platform for deformable display windows.     

Study on morphological, rheological and physico/mechanical behavior of SEBS/CaCO3 nanocomposite

This work focuses on the modification of the mechanical properties and morphology, cure behavior and other characterization of nano CaCO₃ filled SEBS (Styrene-ethylene-butadiene-styrene) elastomers. The tensile strength was increased and compression set characterization was decreased with increasing content of nCaCO₃ value. The influence of the interfacial area and the volume fraction of filler were studied. Furthermore, isothermal cure characterization of neat and filled systems was performed using a torque rheometer. The most important finding base on the rheological studies was the catalytic effect of nCaCO₃ on cure reaction of SEBS, leading to the shorter curing time. Moreover, the kinetic analyses of rheograms revealed a marked decrease in the activation energy of the cure process upon raising nCaCO₃ content. Interestingly, MFI, Hardness, Tensile, Compression set testes showed that the hardness and tensile properties were dramatically increased and MFI and elongation decreased by the addition of nano CaCO₃ into SEBS system compared to pure blend resin. It was shown that the relative increase in tensile yield stress when increasing amount of interfacial agent was added, both depends on the volume of filler and the interfacial area. The nanoparticles shape, size and dispersion state were investigate through X-ray diffraction (XRD), transmission electron microscopy (TEM) and scanning electron microscopy (SEM) method.     

Characterization of plant and animal based natural fibers reinforced polypropylene composites and their comparative study

Natural fibers are largely divided into two categories depending on their origin: plant based and animal based. Plant based natural jute fiber reinforced polypropylene (PP) matrix composites (20 wt% fiber) were fabricated by compression molding. Bending strength (BS), bending modulus (BM), tensile strength (TS), Young’s modulus (YM), and impact strength (IS) of the composites were found 44.2 MPa, 2200 MPa, 41.3 MPa, 750 MPa and 12 kJ/m², respectively. Animal based natural B. mori silk fiber reinforced polypropylene (PP) matrix composites (20 wt% fiber) were fabricated in the same way and the mechanical properties were compared over the silk based composites. TS, YM, BS, BM, IS of silk fiber reinforced polypropylene composites were found 55.6 MPa, 760 MPa, 57.1 MPa, 3320 MPa and 17 kJ/m² respectively. Degradation of composites in soil was measured upto twelve weeks. It was found that plant based jute fiber/PP composite losses its strength more than animal based silk fiber/PP composite for the same period of time. The comparative study makes it clear that mechanical properties of silk/PP composites are greater than those values of jute/PP composites. But jute/PP composites are more degradable than silk/PP composites i.e., silk/PP composites retain their strength for a longer period than jute/PP composites.     

Effect of nanoclay incorporation method on mechanical and water vapor barrier properties of starch-based films

The objective of this study was to investigate the influence of nanoclay incorporation procedure on the mechanical and water vapor barrier properties of starch/nanoclay composite films. Cassava starch films were prepared with (nanocomposite) and without nanoclay (control) in two steps: firstly the production of extruded pellets and secondly thermo-pressing. The nanocomposite films were prepared via two different methods: in D samples the nanoclay was dispersed in glycerol and subsequently incorporated into the starch; and in ND samples all ingredients were added in a single step before the extrusion. All the composite-films were prepared with cassava starch using 0.25 g of glycerol/g of starch and 0.03 g of nanoclay/g of starch. Control samples showed V_A-type crystallinity induced by the manufacturing process and the nanocomposites presented a semicrystalline and intercalated structure. The nanoclay improved the water vapor barrier properties of the starch film and this effect was more pronounced in D samples, where the water vapor permeability (K^w) was 60% lower than that of the control samples. The K^w reduction was associated with decreases in the effective diffusion coefficient (approximately 61%) and in the coefficient of solubility (approximately 22-32%). On the other hand, the incorporation of nanoclay increased the tensile strength and the rigidity of the films and this effect was more significant when the nanoclay was dispersed in glycerol. Thus, the incorporation of nanoclay into starch-based films is a promising way to manufacture films with better mechanical and water vapor barrier properties.     

Preparation and characterization of inner-pressure hollow fiber composite membrane via two-way coating technique for CO<Subscript>2</Subscript>/CH<Subscript>4</Subscript> separation

High-selectivity inner-pressure hollow fiber composite (HFC) membrane for CO₂/CH₄ separation was prepared through the Two-way coating (TWC) technique. The blends of poly(vinylamine) (PVAm)/polyvinyl alcohol (PVA) were coated onto porous hollow fiber polysulfone (PSF) ultrafiltration (UF) membrane with an effective membrane area of 0.4 m². The effects of fabrication parameters on the permselectivity of the resultant HFC membrane were investigated and the optimum preparation conditions were obtained as follows: coating time for 30 min and air blowing time for 30 min after the coating. The prepared HFC membrane showed the typical characteristic of fixed carrier membrane with a high selectivity of CO₂ and CH₄: the separation factor of CO₂/CH₄ (40 vol% CO₂ at 25 °C and 0.2 MPa) was 36.6 and the CO₂ permeability was 56.3 GPU. Field emission scanning electron microscopy (FESEM) images indicated that the HFC membrane prepared by TWC technique had a uniform coating layer along the whole hollow fiber. Membrane permselectivity showed almost no difference between different membrane sections. The HFC membrane showed a good stability during the continuous testing process of 540 h. And the HFC membrane preserved at 30 °C and 40 % humidity exhibited a good durability with a basically unchanged separation factor after 30 days.     

Effect of calcium carbonate nanoparticles on barrier properties and biodegradability of polylactic acid

In this study, the effect of calcium carbonate (CaCO₃) nanoparticles on the barrier properties and biodegradability of polylactic acid (PLA) was investigated. For this purpose, nanocomposite films with various CaCO₃ nanoparticle contents (0, 3, 5, 10, and 15 wt%) were prepared by solution casting method. The gas permeability of nitrogen (N₂), oxygen (O₂), and carbon dioxide (CO₂) was evaluated through a constant volume and variable pressure apparatus at different pressures and temperatures. According to results, barrier properties were improved by loading CaCO₃ nanoparticles up to 5 wt%, and the gas permeability of CO₂, O₂, and N₂ was decreased from 1.4, 0.31, and 0.07 Barrer to 0.48, 0.095, and 0.019 Barrer, respectively. In addition, it was also observed that the gas permeability of samples was decreased by increasing feeding pressure and increased by enhancing temperature. Furthermore, morphological results confirmed the formation of agglomerations and large clusters over 5 wt% CaCO₃ nanoparticles. Finally, the thermal properties and biodegradability of PLA were increased by employing CaCO₃ nanoparticles. These results suggested PLA nanocomposites as favorable candidates for food packaging applications.     

Nano-TiO<Subscript>2</Subscript> based multilayer film deposition on cotton fabrics for UV-protection

Nano-TiO₂ based multilayer nanocomposite films were fabricated on cationically modified woven cotton fabrics by layer-by-layer molecular self-assembly technique. Cationization process was used to obtain cationic surface charge on cotton fabrics. Attenuated total reflectance Fourier transform infrared spectroscopy analyses were used to verify the presence of cationic surface charge and multilayer films deposited on the fabrics. Scanning electron microscope micrographs of poly(sodium 4-styrene sulfonate)/TiO₂, nano polyurethane/TiO₂, and TiO₂/poly(diallyldimethylammonium chloride) multilayer films deposited on cotton fabrics were taken. With nano-TiO₂ based multilayer film deposition, the protection of cotton fabrics against UV radiation is enhanced. The UV protection durability of the self-assembled multilayer films deposited on the cotton fabrics was analyzed after 10 and 20 washing cycles at 40 °C for 30 min. Air permeability and whiteness value analysis were performed on the untreated and multilayer film deposited cotton fabrics. The effect of layer-by-layer deposition process on tensile strength properties of the warp and weft yarns was determined.     

Preparation of magnetic and conductive graphite nanoflakes/SrFe<Subscript>12</Subscript>O<Subscript>19</Subscript>/polythiophene nanofiber-nanocomposites and its radar absorbing application

This study, we synthesized graphite-nanoflakes (GNFs) by acid treatment and thermal shock and then using the ultrasonic irradiation technique to exfoliate flake-carbon. The SrFe₁₂O₁₉ nanoparticles (NPs) were coated by co-precipitate method on GNFs after by alkaline treatment. Finally nanocomposite (GNF/SrFe₁₂O₁₉/PTh) was prepared by in-situ oxidative polymerization method in presence of thiophene (Th) as monomer. The magnetic and electrical conducting properties of the resulting nanocomposites were measured by using vibrating sample magnetometer and standard four-point-probe method, respectively. The synthesized nanocomposites were characterized by X-ray diffraction (XRD) and fourier transform infrared spectra (FTIR). In addition, morphological analyses were investigated by scanning electron microscopy (SEM). A minimum reflection loss (RL) of GNFs/SrFe₁₂O₁₉/PTh with 50 % wt GNFs/SrFe₁₂O₁₉ as core were observed ?28 and ?39 dB at 9.7 and 12 GHz for a 1.5 mm thickness. The results indicated that we can perform good microwave shielding in X-band (8–12 GHz) by these nanocomposites.     

Electrospun curcumin loaded poly(lactic acid) nanofiber mat on the flexible crosslinked PVA/PEG membrane film: Characterization and <Emphasis Type="Italic">in vitro</Emphasis> release kinetic study

Herein, a biodegradable and biocompatible composite comprising of support membrane based on crosslinked PVA/PEG film and curcumin loaded electrospun poly(lactic acid) (PLA) nanofiber mat is introduced. The membrane film was prepared from PVA/PEG blend followed by crosslinking with an optimum amount of citric acid, 15 wt.%. After then, PLA solutions with different curcumin content, 0-11 wt.%, were electrospinned on the prepared membrane substrate. The prepared film showed high water absorption, water vapor transmission rate and superior mechanical properties with improved elastic modulus, tensile strength and with an elongation of around 320 % with respect to the non-crosslinked one. Also, the scanning electron microscopy was revealed uniformly dispersed pores throughout the membrane film with a nearly narrow in size distribution centered at 36 μm. As well, a nanostructure porous morphology was found for the electrospun fibrous curcumin loaded PLA from the scanning electron microscopy micrographs and the average fiber diameter was decreased with curcumin content. In vitro drug release from the prepared flexible composite into the vertical diffusion cell was recorded by the measuring curcuminoids content using high performance liquid chromatography and drug release kinetic evaluations were revealed that the release pattern of all prepared samples, containing different content of curcumin, well fitted to the Higuchi’s model signifying diffusion-controlled release mechanism. As well, the determined release rate at the second release stages, i.e. steady state flux (J), was varied from 0.31 to 43.53 μg·cm^-2·h^-1 with increasing drug content from 1 to 11 wt.%. Regarding this results, this flexible composite by providing the moist environment along with miraculous healing properties of curcumin, can be potential candidate for transdermal drug delivery.     

Nanocellulose reinforced PVA composite films: Effects of acid treatment and filler loading

Nanocellulose was prepared by acid hydrolysis of microcrystalline cellulose (MCC) at different hydrobromic acid (HBr) concentrations. Polyvinyl alcohol (PVA) composite films were prepared by the reinforcement of nanocellulose into a PVA matrix at different filler loading levels and subsequent film casting. Chemical characterization of nanocelluloses was performed for the analysis of crystallinity (X_c), degree of polymerization (DP), and molecular weight (M_w). The mechanical and thermal properties of the nanocellulose reinforced PVA films were also measured for tensile strength and thermogravimetric analysis (TGA). The acid hydrolysis decreased steadily the DP and M_w of MCC. The crystallinity of MCC with 1.5 M and 2.5 M HBr showed a significant increase due to the degradation of amorphous domains in cellulose. Higher crystalline cellulose showed the higher thermal stability than MCC. From X-ray diffraction (XRD) analysis, nanocellulose samples showed the higher peak intensity than MCC cases. Reduction of MCC particle by acid hydrolysis was clearly observed from scanning electron microscope (SEM) images. The tensile and thermal properties of PVA composite films were significantly improved with the increase of the nanocellulose loading.     

Mechanical behaviour of composites filled by agro-waste materials

The present paper is concerned with the effect of cork and rice husk ash micro particles fillers on the mechanical properties (flexural resistance, fracture toughness, impact absorbed energy, elastic and viscous moduli) of polyester based composite. Composite sheets were hand molded using weight filler fractions of 1, 2.5, and 5 %. Flexural strength of filled materials was much lower than the polyester matrix, with more pronounced effect for cork powder, decreasing significantly with filler content increases. Fracture toughness decreases also on the filled composites. Using cork powder fracture toughness decreases significantly when filler content increases, while for rice husk ash filler a slight increase was observed. Both fillers improve absorbed impact energy, peaking at about 2.5 % of filler content. Best improvements were obtained using rice husk ash powder, reaching about 30 %. Both fillers increase glass transition temperature and the maximum use temperature and also the elastic modulus compared with polyester. It can be concluded from this study that the used agro-waste materials are attractive reinforcements from the standpoint of their mechanical properties.