Removal of Remazol Red Rb by using Al (III) as Coagulant-Flocculant: Effect of Some Variables on Settling Velocity

This study addresses the research of the removal of a textile dye from aqueous solutions by using aluminum ions as coagulant-flocculant. A simulated textile wastewater was prepared from Remazol Red RB textile dye. The purpose of this study was to investigate the effects of temperature, pH, and concentrations of the cationic surfactant and electrolyte concentration on the settling velocity ofthe simulated textile wastewater. While investigating these factors, levels of variables were determined by considering the characteristicsof traditional textile wastewater like pH, temperature, and dye concentration. Although traditional coagulation-flocculation processesmake use of different aluminium salts as coagulant-flocculent, in this study, Al ions dissolved in pH and temperature of traditional textilewastewater were used. Furthermore, sludge volume index values (SVI) were determined and conductivity measurements carried out. The resultsshowed that, in the working range of these variables, the spectroscopic color measurement revealed 100% decolorization yieldof wastewater. In conclusion, researchers found that the optimum settling velocity conditions were as follows: low temperature (273K),surfactant concentration of 0.10 g L^-1, electrolyte concentration of 0.10 g L^-1, dye concentration of 0.025 g L^-1 and a pH of 10.05. Finally, by conducting experiments twice under the obtained optimum values, mean settling velocity was 0.014 m min^-1 and the mean sludge volume index 140 mL g^-1.     

Speciation of Phosphorus and Cadmium in a Contaminated Soil Amended with Bone Char: Sequential Fractionations and XANES Spectroscopy

In this work, photocatalytic degradation of two reactive dyes, Reactive Yellow 84 (RY 84) and Reactive Black 5 (RB 5), on FeTiO₃/TiO₂ heterojunction in the presence of UV–visible radiation and H₂O₂ has been reported. FeTiO₃/TiO₂ heterojunction has been prepared from ilmenite FeTiO₃ and anatase TiO₂ by employing oxalic acid as an organic linker. FeTiO₃/TiO₂ ratios have been varied from 1 to 5 wt.%, and the materials were characterized by X-ray diffraction, scanning electron microscope and diffused reflectance UV–visible spectroscopic analysis. The photocatalytic activity of FeTiO₃/TiO₂ heterojunction for the degradation of the organic dyes RY 84 and RB 5 in the presence of UV–visible light was found to be higher than that of pure TiO₂. The addition of H₂O₂ increases the rate of degradation of both dyes on FeTiO₃/TiO₂ heterojunction. It facilitates the fast degradation of dye solutions even when their concentration was above 100 mg/l, which is otherwise very slow due to the low transmittance of light by the dye solution. The extent of mineralisation of the reactive dye during photocatalytic degradation was estimated from chemical oxygen demand analysis. FeTiO₃/TiO₂ heterojunction photocatalyst was also found to have good photostability; the material retains almost 97 % of its initial activity even in the fifth cycle.     

TiO2-Assisted Photodegradation of Direct Blue 78 in Aqueous Solution in Sunlight

The photodegradation of azo dyes aqueous solution has been investigated using TiO₂ as catalyst in sunlight. The effect of amount of catalyst, concentration of dye, and pH value on the degradation of Direct Blue 78 was observed. A complete degradation of 100 mg/L Direct Blue 78 solution under solar irradiation was achieved in 6 h at pH?3.0, dosage of TiO₂ 1.0 g/L. A possible pathway for the photodegradation of Direct Blue 78 in sunlight was proposed.     

Comparative Study on Photocatalytic Degradation of Mono Azo Dye Acid Orange 7 and Methyl Orange under Solar Light Irradiation

The objective of this study was to investigate and compare the kinetic photocatalytic degradation of mono azo dyes Acid Orange 7 (AO7) and Methyl Orange (MO) under solar light irradiation with titanium dioxide (TiO₂) as a photocatalyst. Several operational parameters affecting the photocatalytic degradation of dye were evaluated such as different azo dyes, initial dye concentration, TiO₂ dosage, with and without aeration and sunlight irradiation. The data obtained was well fitted with the Langmuir?CHinshelwood kinetic model. It was observed that the pseudo-first-order rate constants for AO7 were higher than MO in all cases, indicating that the photocatalytic degradation of AO7 was easier and more rapid than MO. The analysis of chemical oxygen demand and UV?CVis spectra shows the AO7 and MO not only being decolorized due to the breakdown of azo bond but also being mineralized if the azo dye solutions were continually exposed to solar light irradiation after the decolorization process.     

Photo-Degradation of Some Dyes using Ag-Loaded Titaniumdioxide

The photocatalytic degradation of organic dyes using TiO₂ andsilver-loaded TiO₂ has beenstudied. The dyes which were chosen (methyl violet, a cationicdye; Cibacron Blue FMR, areactive dye; and Maxilon Red GRL, a mono azo basic dye)represent the major structuralfamilies of organic dyes. Ag-loading dramatically reduceddegradation time. While theundoped TiO₂ degraded about 63% of the total amount ofmethyl violet within 4 min,degradation rose to 95% with Ag-loaded TiO₂ within the sametime period. The photo-decomposition of dyes was monitored as a function of pH anddissolved organic and inorganic matters.     

Potential of Gonium spp. in Synthetic Reactive Dye Removal, Possible Role of Laccases and Stimulation by Triacontanol Hormone

In this study, Gonium sp. was investigated for possible usage in dye-containing wastewater treatment. Trials were performed in media including triacontanol hormone, Reactive Orange 14, Reactive Red 120, Reactive Black 5, Remazol Brilliant Blue R (RBBR), and also hormone against the controls. Algae could remove RBBR with the highest dye removal percentage (56%) among the tested dyes. The optimum pH was 9 in removing 50 mg L^?1 RBBR at a dye removal percentage of 47.1%. The role of laccase activity of Gonium sp. was also investigated. This first attempt in the literature showed the involvement of the enzyme in the algal growth and bioremoval process. In the presence of the plant growth hormone in the culture, the activity showed a steady and significant increase up to nearly sixfold between 5th and 14th days of incubation.     

Biotreatment of Melanoidin-Containing Distillery Spent Wash Effluent by Free and Immobilized Aspergillus oryzae MTCC 7691

Humic acids (HA) are known as the precursors of carcinogenic compounds formed by the disinfection of drinking water. While conventional treatments were found to be inefficient HA removal processes in drinking water, advanced oxidation processes have been proven to have a significant effect in the treatment of HA. The degradation of HA was investigated using nano-sized zinc oxide (ZnO)/laponite composite (NZLC). The reactions occurred in a UVC reactor by considering following variables: pH, initial HA concentration, catalyst loading, addition of hydrogen peroxide (H₂O₂), and catalyst reuse. Water samples containing HA were analysed by ultraviolet/visible spectrophotometer and high-performance size-exclusion chromatography. Initial HA concentrations were tested by the Langmuir–Hinshelwood model with k and K _ads values, determined to be 0.126 mg/L.min and 0.0257 L/mg, respectively. The change in pH affected the HA degradation efficiency by the photocatalytic activity where it was higher under acidic conditions rather than alkaline ones. Optimal catalyst loading was proved to be a constrained factor in influencing the photocatalytic efficiency: the increase of catalyst concentration enhanced the HA decomposition efficiency up to an optimum value of 20 g/L, where there was no further degradation with excess loading. The addition of H₂O₂ was investigated through homogenous and heterogeneous photocatalysis, and, heterogeneous photocatalysis showed higher removal efficiency due to the combined effect of both catalysts and H₂O₂. Finally, NZLC was effective for reuse and exhibited an excellent stability after six times of usage.     

Decolorization and Degradation of Reactive Dye in Aqueous Solution by Ozonation in a Semi-batch Bubble Column Reactor

The decolorization and degradation of anionic sulphonated azo dye (Reactive orange 16 (RO16)), which is suspected to be carcinogenic, were investigated using ozone. The decolorization process of the reactive dye was carried out by bubbling ozone at the bottom of a bubble column reactor containing the dye solution. The effect of pH, reaction time, dye concentration, ozone concentration, and decolorization time was studied. Also, degradation products and possible degradation mechanism were investigated. The results showed that ozonation was a highly effective way to remove color from wastewater. The color of a synthetic waste solution containing water-soluble reactive dye was reduced to 69.69 % under the basic condition (pH 12), with complete RO16 degradation occurring in 8 min. Ozone consumption continued for a further 16 min after which time most of the degradation reactions were complete. Kinetic studies showed that direct ozonation of the aqueous dyes represented a pseudo-first-order reaction with respect to the dye. The apparent rate constant increased with both the applied ozone dose and higher pH values and declined logarithmically with the initial dye concentration. Intermediates such as 6-acetylamino-3-aminonaphthalene-2-sulfonic acid, 2-(4-nitrosophenyl) sulfonylethyl hydrogen sulfate, and 6-acetamido-4-hydroxy-3-nitroso naphthalene-2-sulfonic acid were detected by gas chromatograph coupled with mass spectrometry in the absence of pH buffer, while nitrate and sulfate ions and formic, acetic, and oxalic acids were detected by ion chromatography.     

Sequential Microaerophilic-Oxic Phase Mineralization of Azo Dyes by a Monoculture of Pseudomonas Aeruginosa Strain AWF Isolated from Textile Wastewater

A novel dye degrading bacterium capable of decolorizing and mineralizing four different dyes (Methyl red, Orange II, Direct red 80, and Direct blue 71) was isolated from textile industrial wastewater using the selective enrichment technique. The bacterium was identified as Pseudomonas aeruginosa. More than 80 % decolorization of Direct red 80 was obtained under microaerophilic conditions in 48 h, whereas only 10 % color removal was obtained under oxic conditions at the same time. Subsequent aeration of the decolorized medium resulted in the mineralization of the metabolic intermediates generated after azo bond cleavage by P. aeruginosa as confirmed by total organic carbon content and high-performance liquid chromatography analyses. The degradation products were characterized by Fourier transform infrared spectrometer and nuclear magnetic resonance techniques whereas the biotoxicity profile of the samples were evaluated using the brine shrimp lethality test assay. Data from this study provide evidence of dye mineralization and detoxification by a monoculture of P. aeruginosa in successive microaerophilic/oxic stages.     

TiO2纳米粒子气固相光催化降解乙烯初探

该文对TiO₂纳米粒子气固光催化降解果蔬贮藏环境乙烯技术进行了初步研究。采用溶胶-凝胶法制备的纳米TiO₂薄膜作光催化剂，利用自行设计的气固光催化实验系统，研究了乙烯浓度、紫外光作用时间对光催化降解反应的影响，探讨了乙烯的光催化降解的动力学。结果显示：该研究所制备的TiO₂锐钛矿型含量为48.766%，比表面积为47.186 m²/g，具有良好的光催化性能；光催化降解乙烯比直接紫外线光降解效果显著，光照10 min时光催化乙烯降解率比直接紫外线光降解提高23.76%；乙烯的降解率随着其浓度的增加而降低；乙烯的光催化降解的动力学可以用Langmuir-Hinshelwood动力学方程加以描述。     

Community Refinery Wastewater Photodegradation by Fe-Doped TiO<Subscript>2</Subscript> Films

Photocatalytic treatment of real community wastewater using Fe-doped TiO₂ nanofilm was prepared by modified sol-gel method together with a simple dip-coating technique. The process was investigated in a home-made batch photoreactor. The as-prepared nanocomposite film was characterized by UV-Vis diffuse, XRD, BET, and Fe-SEM analysis. The poultry processing wastewater was collected from Nakhonsawan Municipality. Subsequently, the photocatalytic treatment of the wastewater was performed using a home-made photoreactor operated in batch mode to demonstrate the effects of Fe-dopant concentration with various layer numbers. The catalysts were irradiated using four lamps of 15 W power that emitted visible light and performed at room temperature. The samples were collected every 15 min and analyzed for biochemical oxygen demand (BOD) and chemical oxygen demand (COD) removal efficiency compared to pure TiO₂ nanofilm and direct photolysis. From the results, the mixture of rutile and anatase was obtained with the maximum specific surface area of 150.12 mg²/g and the average particle size of 39.95 nm for 3 layers of 0.15% wt/v Fe-doped TiO₂. The BOD and COD value at 90 min time treatment was presented to be 8.87 and 32 mg L^?1, respectively, in the presence of 0.15% wt/v Fe-doped TiO₂ film photocatalysts. Moreover, atomic absorption spectrometric result ensured that no Ti contamination was detected in all parts of plants after watering by the treated water. Hence, the photocatalytic treatment markedly improved the quality of the community wastewater.     

Decolorization of Textile Effluent by Soluble Fenugreek (Trigonella foenum-graecum L) Seeds Peroxidase

Peroxidase from fenugreek (Trigonella foenum-graecum) seeds was highly effective in the decolorization of textile effluent. Effluent was recalcitrant to the action of fenugreek seeds peroxidase (FSP). However, in order to effectively decolorize effluent by peroxidase, the role of six redox mediators has been investigated. The maximum decolorization of textile effluent was observed in the presence of 1.0 mM 1-hydroxybenzotrizole, 0.7 mM H₂O₂, and 0.4 U ml^?1 of FSP in the buffer of pH 5.0 at 40°C in 2.5 h. The decolorization of textile effluent in a batch process by peroxidase was 85% in 5 h, whereas the complete decolorization of textile effluent by membrane-entrapped FSP was observed within 11 h of its operation. The absorption spectra of treated effluent exhibited a marked diminution in the absorbance at different wavelengths compared to untreated effluent.     

Degradation of Di-(2-ethylhexyl) Phthalate (DEHP) by TiO2 Photocatalysis

The photocatalytic degradation of di-(2-ethylhexyl) phthalate (DEHP) in solution using titanium dioxide (TiO₂) was analyzed in this study. It was found that DEHP was completely removed in the solution after 150 min irradiation. The effect of different factors, such as photocatalyst amount, DEHP concentration, light intensity, pH, and temperature on photocatalytic degradation was investigated. The degradation mechanism of DEHP with proton and hydroxyl radicals oxidation were also studied. It is suggested that either ethylhexyl or ester chain scissions of the aliphatic part of DEHP was the dominant degradation mechanism of the process. The photocatalytic degradation process was well described by first-order reaction. The final mineralization product was carbon dioxide and the intermediate products were identified by GC-MS. Thus, the photocatalytic degradation treatment of DEHP in wastewater is a relative simple and fast method.     

Photocatalytic Degradation of Reactive Black 5 by Fish Scale-Loaded TiO2 Composites

Titania and TiO₂/fish scale composites at different mass ratios (90:10, 70:30, and 50:50) were prepared by sol?Cgel method for application as photocatalysts in this study. Fish scale, synthesized TiO₂, and TiO₂/fish scale composites were characterized by using X-ray diffraction (XRD), scanning electron microscope (SEM), and nitrogen sorption. Their photocatalytic activities were evaluated through the degradation of Reactive Black 5 (RB 5) under solar light irradiation. The effects of irradiation time, catalyst loading, and mass ratios of TiO₂/fish scale composites on the photocatalytic degradation of RB 5 were investigated. The results revealed that the photocatalytic activity of TiO₂/fish scale composites showed compatible and enhanced degradation compared to the synthesized titania.     

Biodegradation and Detoxification Efficiency of Azo-Dye Reactive Orange 16 by <Emphasis Type="Italic">Pichia kudriavzevii</Emphasis> CR-Y103

In consideration of the hazards associated with the presence of the textile azo-dye and their biotransformation products in the environment, the goal of this work was to study bioremediation process by the yeast strain Pichia kudriavzevii CR-Y103 related to the ability to degrade and detoxify the sulfonated Reactive Orange 16 azo-dye. In experimental conditions, the optimal inoculum/dye concentration ratio required for complete decolorization (100%) of culture medium and biomass within 24 h has been 1 g L^?1 yeast cell (dry weight)/50 mg L^?1 Reactive Orange 16. In the presence of 400 mg L^?1 of Reactive Orange 16 (RO16), 95% of the dye was removed after 72 h of incubation. Also, the yeast strain could decolorize other eight textile dyes (56.48–99.98% decolorization within 24 h). NADH-DCIP reductase and azo reductase activities were significantly increased (ca. 5.4 times and ca. 37 times, respectively) during the decolorization process. UV-VIS spectra, high-performance liquid chromatography (HPLC), and Fourier transform infrared spectroscopy (FTIR) analysis confirmed the presence of new biotransformation products in extracted metabolites, highlighting the partial biodegradation of the dye by the new yeast isolate. The phytotoxicity evaluation strongly supported the decreased toxicity of biodegraded products as minor inhibition on germination (%), root and shoots elongation of T. pratense L. and T. aestivum L. seedlings. Increasing of mitotic index value and decreasing the frequency of chromosomal aberrations in tested plant meristem cells treated with biodegraded products, compared with RO16 treatment (500 ppm), confirmed their slightly toxic nature. A cell viability assay also confirmed the reduced toxicity of biodegraded products on healthy monkey kidney cells (Vero cells).     

Degradation of Hazardous Dyes in Wastewater using Nanometer Mixed Crystal TiO2 Powders under Visible Light Irradiation

The partial phase transformation of nanometer TiO₂ powder from anatase phase to rutile phase was realized by heat-treatment and a new TiO₂ photocatalyst which could be excited by visible light was obtained. The heat-treated TiO₂ powder at different stage of transition crystal was characterized and monitored by XRD, TEM, FT-IR and UV–vis DRS methods. The test of photocatalytic activity of the heat-treated TiO₂ powder was carried out by the photocatalytic degradation of rhodamine B and acid orange II dyes, respectively, in aqueous solution under visible light irradiation. The results indicate that the nanometer TiO₂ photocatalyst heat-treated at 500°C for 60 min shows the highest photocatalytic activity, that is, it can effectively degrade the rhodamine B and acid orange II under visible light irradiation. The remarkable improvement of photocatalytic activity of heat-treated TiO₂ powder at 500°C for 60 min was mainly illustrated by the formation of special interphase between rutile and anatase phases, which not only restrains the recombination of photogenerated electrons and holes, but also reduces the adsorbability of nanometer anatase TiO₂ powder properly for various dyes. Additionally, the effects of dye-assisting chemicals such as Na₂CO₃ and NaCl on the photocatalytic degradation were also studied.     

Degradation of Leather Dye Using CeO2–SnO2 Nanocomposite as Photocatalyst Under Sunlight

Nanocomposite of CeO₂?CSnO₂ containing different CeO₂ contents was prepared by coprecipitation process. The material obtained was characterized by X-ray diffraction and N₂ adsorption?Cdesorption isotherms. Its photocatalytic activity was tested in the degradation of azo dye of leather, Direct Black 38, in aqueous solution under sunlight. The photocatalytic activity of the coupled CeO₂?CSnO₂ oxide ranged depending on the CeO₂ contents. The optimum amount of CeO₂ for the synthesis of CeO₂?CSnO₂ was 7?wt.% since the nanoparticles showed high photocatalytic activity in the degradation of the dye, similar to that of the TiO₂?CP25 photocatalyst. The kinetics of photocatalytic degradation and total organic carbon removal under sunlight were found to follow a first-order rate law. The results indicated that CeO₂?CSnO₂ can be used for the removal of dyes from wastewater.     

Organics Wastewater Degradation by a Mesoporous Chromium-Functionalized γ-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> with H<Subscript>2</Subscript>O<Subscript>2</Subscript> Assistance

In this study, a mesoporous chromium-functionalized γ-Al₂O₃ (Cr/γ-Al₂O₃) catalyst was prepared by an impregnation method, and the catalytic activity was evaluated by the degradation of organics wastewater. The prepared catalyst was characterized by X-ray photoelectron spectroscopy, X-ray diffraction, nitrogen adsorption-desorption experiments, and scanning electron microscopy. The characterization results confirmed that the pores in the Cr/γ-Al₂O₃ catalyst distributed broadly in the mesoporous region, and the active chromium species were highly dispersed on the catalyst surface. The catalytic activity tests showed that the Cr/γ-Al₂O₃ catalyst exhibited a superior performance for the degradation of organics wastewater with H₂O₂ assistance. And the methylene blue (MB) disappeared within 20 min and the COD removal reached 76.5% within 40 min for the MB-simulated wastewater; for the phenol-simulated wastewater, the phenol removal was above 95% and the corresponding COD removal reached 71% within 40 min. Such an excellent catalytic performance demonstrates that the Cr/γ-Al₂O₃ catalyst has a potential application in the degradation of complex organics wastewater simultaneously.     

Effect of Metals on Decolorization of Reactive Blue HERD by <Emphasis Type="Italic">Comamonas</Emphasis> sp. UVS

Comamonas sp. UVS was able to decolorize Reactive Blue HERD (RBHERD) dye (50 mg L^?1) within 6 h under static condition. The maximum dye concentration degraded was 1,200 mg L^?1 within 210 h. A numerical simulation with the model gives an optimal value of 35.71?±?0.696 mg dye g^?1 cell h^?1 for maximum rate (V_max) and 112.35?±?0.34 mg L^?1 for the Michaelis constant (K_m). Comamonas sp. UVS has capability of decolorization of RBHERD in the presence of Mg²⁺, Ca²⁺, Cd²⁺, and Zn²⁺, whereas decolorization was completely inhibited by Cu²⁺. Metal ions also affected the levels of biotransformation enzymes during decolorization of RBHERD. Comamonas sp. UVS was also able to decolorize textile effluent with significant reduction in COD. The biodegradation of RBHERD dye was monitored by UV–vis spectroscopy, FTIR spectroscopy, and HPLC.     

Advances in Heterogeneous Photocatalytic Degradation of Phenols and Dyes in Wastewater: A Review

The heterogeneous photocatalytic water purification process has gained wide attention due to its effectiveness in degrading and mineralizing the recalcitrant organic compounds as well as the possibility of utilizing the solar UV and visible light spectrum. This paper aims to review and summarize the recently published works in the field of photocatalytic oxidation of toxic organic compounds such as phenols and dyes, predominant in wastewater effluent. In this review, the effects of various operating parameters on the photocatalytic degradation of phenols and dyes are presented. Recent findings suggested that different parameters, such as type of photocatalyst and composition, light intensity, initial substrate concentration, amount of catalyst, pH of the reaction medium, ionic components in water, solvent types, oxidizing agents/electron acceptors, mode of catalyst application, and calcinations temperature can play an important role on the photocatalytic degradation of organic compounds in water environment. Extensive research has focused on the enhancement of photocatalysis by modification of TiO₂ employing metal, non-metal, and ion doping. Recent advances in TiO₂ photocatalysis for the degradation of various phenols and dyes are also highlighted in this review.