Determination of organochlorine and organophosphorus pesticide residues in eggs using a solid phase extraction cleanup

A multiresidue solid phase extraction (SPE) method for the isolation and subsequent gas chromatographic determination of nonpolar organochlorine and polar organophosphorus pesticide residues in eggs is described. The method uses an acetonitrile extraction followed by an SPE cleanup using graphitized carbon black and aminopropyl SPE columns. Organophosphorus pesticides are determined by gas chromatography with flame photometric detection. After further cleanup of the extract using Florisil SPE columns, organochlorine pesticides are determined by gas chromatography with electron capture detection. Studies were performed using eggs containing both fortified and incurred pesticide residues. The average recoveries were 86-108% for 8 fortified organochlorine pesticide residues and 61-149% for 28 fortified organophosphorus pesticide residues.     

Sample extraction method combining micellar extraction-SPME and HPLC for the determination of organochlorine pesticides in agricultural soils

A method for the determination of organochlorine pesticides in soil samples combining microwave assisted micellar extraction (MAME) with solid-phase microextraction (SPME) and high-performance liquid chromatography-UV has been developed. A mixture of two nonionic surfactants (polyoxyethylene 10 lauryl ether and polyoxyethylene 10 stearyl ether) was used for the extraction of pesticides from agricultural soils, and different types of SPME fibers were compared. The different parameters which affect extraction efficiency in the SPME procedure were optimized such as extraction time and temperature. The method developed involves extraction and preconcentration for the target analytes in soil samples. The analytical parameters were also studied and good recoveries obtained, RSD being lower than 10% and detection limits ranging between 36 and 164 ng g(-1) for the pesticides studied. The proposed method was successfully applied to the determination of some organochlorine pesticides in several kinds of agricultural soil samples with different characteristics.     

Simplified extraction and cleanup for multiresidue determination of pesticides in lanolin

In the proposed method, a light petroleum solution of lanolin (wool fat) is adsorbed on diatomaceous earth in an Extrelut column, and the pesticides are eluted with acetonitrile saturated with light petroleum. After evaporation to a small volume, the extract is subjected to solid-phase extraction (SPE) on a C-18 column. The acetonitrile eluate is evaporated to dryness and the residue is taken up in light petroleum. Organophosphorus pesticides are determined by temperature-programmed gas chromatography (GC) on a wide-bore column using a flame photometric detector in the phosphorus mode. Organochlorine pesticides are determined after miniaturized Florisil cleanup by classic GC on an OV-17/QF-1 packed column, using an electron capture detector. This procedure is more rapid and straightforward than the time-consuming AOAC extraction method, 29.014. Cleanup was better and the results obtained were comparable. Recoveries for 13 organochlorine and organophosphorus pesticides, frequently found in lanolin, ranged from 80 to 90%.     

Supercritical fluid extraction of organochlorine pesticides in eggs

The efficacy of supercritical fluid extraction (SFE) for the recovery of 16 common organochlorine pesticides (OCPs) from liquid whole eggs was investigated by employing supercritical carbon dioxide (SC-CO(2)) without the use of a solvent modifier to minimize interfering coextractives. The OCPs tested included aldrin; alpha-, beta-, delta-, and gamma-BHCs; p,p'-DDD, -DDE, and -DDT; dieldrin; endosulfans I, II, and sulfate; endrin; endrin aldehyde; heptachlor; and heptachlor epoxide. The SFE conditions were as follows: 10000 psi (680 bar), 40 degrees C, SC-CO(2) flow rate of 3.0 L/min with an extraction time of 40 min for a total of 120 L of CO(2). The OCPs were trapped off-line in an SPE cartridge containing Florisil and then eluted by an acetone/hexane mixture and analyzed by gas chromatography-electron capture detection (GC-ECD). Recovery studies were carried out on homogenized eggs fortified at the 0.05, 0.10, and 0.20 ppm levels. At the lowest level, 0.05 ppm, recoveries ranged from 81.8 to 108.3%, with CVs < 9.8%. All recoveries were significantly higher than those obtained by an AOAC/FDA solvent extraction method. Eggs containing incurred endosulfan I were also effectively extracted by SFE. This study suggests that the application of SFE for the extraction of OCPs from eggs will result in significant savings in analysis time and lower solvent use and disposal costs compared to conventional solvent extraction procedures.     

Potential of a simple mechanical extraction system for the rapid extraction of pesticides from foodstuffs. Application to the determination of organochlorine pesticides in lettuce.

The efficiency of a simple mechanical extraction system as applied in veterinary drug analysis has been tested in the field of pesticide residue analysis. As a first application, the system was used for the extraction of organochlorine pesticides from vegetables. The convenience of this simple extraction system consists of performing mechanical extraction in disposable polyethylene-based extraction bags, reducing considerably manual operation and cross-contamination. For the tested compounds and matrix (lettuce), recoveries of the 10 organochlorine pesticides performed at two spiking levels (n = 4 each level and compound) ranging between 0.06 and 3.3 mg/kg were between 60 and 80%, with most standard deviations <5%. The extraction method appeared to be simple and fast with a great potential for the analysis of many pesticide-matrix combinations.     

Analysis of agricultural residues on tea using d-SPE sample preparation with GC-NCI-MS and UHPLC-MS/MS

This study presents new sample preparation and analytical procedures for the quantification of pesticides on processed tea leaves. The new method includes tea extraction and dispersive solid phase extraction (d-SPE) to prepare gas chromatography (GC) and ultrahigh-performance liquid chromatography (UHPLC)-ready samples, providing a fast and cost-effective solution for time-sensitive industrial analysis to fulfill regulatory requirements. Both GC-negative chemical ionization mass spectrometry (GC-NCI-MS) and UHPLC-tandem mass spectrometry (UHPLC-MS/MS) were employed to produce highly sensitive and reproducible data. Excellent limits of detection (typically below 1 μg/kg for GC and 10 μg/kg for UHPLC), wide linearity ranges, and good recoveries (mostly >70%) were achieved on the selected pesticides. Twenty-seven tea samples purchased from local grocery stores were analyzed using the newly developed methods. Among the pesticides analyzed, endosulfan sulfate and kelthane were the most frequently detected by GC-NCI-MS and imidacloprid and acetamiprid by UHPLC-MS/MS in these teas. The samples were found to be relatively clean, with <1 mg/kg of total pesticide residues. The organic-labeled teas were significantly cleaner than nonorganic ones. The cost per gram of tea did not correlate with pesticide residue levels detected.     

Multiresidue determination of pesticides in malt beverages by capillary gas chromatography with mass spectrometry and selected ion monitoring

A method was developed to determine pesticides in malt beverages using solid phase extraction on a polymeric cartridge and sample cleanup with a MgSO4-topped aminopropyl cartridge, followed by capillary gas chromatography with electron impact mass spectrometry in the selected ion monitoring mode [GC-MS(SIM)]. Three GC injections were required to analyze and identify organophosphate, organohalogen, and organonitrogen pesticides. The pesticides were identified by the retention times of peaks of the target ion and qualifier-to-target ion ratios. GC detection limits for most of the pesticides were 5-10 ng/mL, and linearity was determined from 50 to 5000 ng/mL. Fortification studies were performed at 10 ng/mL for three malt beverages that differ in properties such as alcohol content, solids, and appearance. The recoveries from the three malt beverages were greater than 70% for 85 of the 142 pesticides (including isomers) studied. The data showed that the different malt beverage matrixes had no significant effect on the recoveries. This method was then applied to the screening and analysis of malt beverages for pesticides, resulting in the detection of the insectide carbaryl and the fungicide dimethomorph in real samples. The study indicates that pesticide levels in malt beverages are significantly lower than the tolerance levels set by the United States Environmental Protection Agency for malt beverage starting ingredients. The use of the extraction/cleanup procedure and analysis by GC-MS(SIM) proved effective in screening malt beverages for a wide variety of pesticides.     

Multiresidue screening of pesticides in fruits using an automatic solid-phase extraction system

About 20 pesticides were determined in lyophilized fruits using a semiautomatic multiresidue method, based on solid-phase extraction (SPE) with a silica column. The lyophilization of the sample, besides the SPE procedure selected, provided clean extracts despite the complexity of the matrixes studied. In addition, the lyophilization process allows sample preservation for at least three months without changes in the concentrations of the pesticides. Determination and quantitation of organochlorine and pyrethroid residues was carried out using a gas chromatograph equipped with an electron capture detector (GC-ECD), and a mass spectrometric detector (GC-MS) was used for confirmation purposes. Organochlorine pesticides provided average recoveries (spiked at three concentration levels in eight different fruits) near 93 +/- 4%, being lower (89 +/- 8%) for pyrethroids as a consequence of their higher degradation and interaction with the sample matrix. On the other hand, the detection limits achieved for all pesticides (0.5-8 ng per g of lyophilized fruit) allow their determination at the MRLs established by the European Union, with good precision ( approximately 5%). Finally, from the 100 different fruits screened, only 10 positive responses were obtained, which were further confirmed by GC-MS.     

Organochlorine pesticide residues in strawberries from integrated pest management and organic farming

A rapid, specific, and sensitive method based on the Quick Easy Cheap Effective Rugged and Safe (QuEChERS) method and a cleanup using dispersive solid-phase extraction with MgSO(4), PSA, and C18 sorbents has been developed for the routine analysis of 14 pesticides in strawberries. The analyses were performed by three different analytical methodologies: gas chromatography (GC) with electron capture detection (ECD), mass spectrometry (MS), and tandem mass spectrometry (MS/MS). The recoveries for all the pesticides studied were from 46 to 128%, with relative standard deviation of <15% in the concentration range of 0.005-0.250 mg/kg. The limit of detection (LOD) for all compounds met maximum residue limits (MRL) accepted in Portugal for organochlorine pesticides (OCP). A survey study of strawberries produced in Portugal in the years 2009-2010 obtained from organic farming (OF) and integrated pest management (IPM) was developed. Lindane and β-endosulfan were detected above the MRL in OF and IPM. Other OCP (aldrin, o,p'-DDT and their metabolites, and methoxychlor) were found below the MRL. The OCP residues detected decreased from 2009 to 2010. The QuEChERS method was successfully applied to the analysis of strawberry samples.     

Gas chromatographic determination of electron capture sensitive volatile industrial chemical residues in foods, using AOAC pesticide multiresidue extraction and cleanup procedures

Electron capture (EC) gas chromatographic (GC) parameters have been developed for determining some of the more volatile industrial chemicals that can be determined by the AOAC multiresidue method for organochlorine and organophosphorus pesticides with modified GC operating conditions. Retention times relative to pentachlorobenzene are reported for 143 industrial chemicals, pesticides, and related compounds on OV-101 GC columns at 130 degrees C. Also reported for most of the compounds are recoveries from fortified samples carried through the AOAC extraction and cleanup procedures for fatty and/or nonfatty foods, Florisil elution characteristics, and GC relative retention times on mixed OV-101 + OV-210 columns at 130 degrees C. Our laboratory has used the modified EC/GC parameters with the AOAC multiresidue extraction/cleanup procedures to determine many volatile halogenated industrial chemical contaminants in foods, chiefly in samples of fresh-water fish. Other modifications of the AOAC method are described to improve the tentative identification and quantitative measurement of these volatile residues.     

Organochlorine pesticides and polychlorinated biphenyls in sediment and fish from Wetlands in the north central United States

Sediment samples collected in 1980-1982 from riverine and pothole wetlands at 17 locations in the north central United States were analyzed for organochlorine pesticides, certain of their metabolites, and polychlorinated biphenyls (PCBs). Concentrations were above minimum detection levels (5 ng/g of organochlorines and 20 ng/g of PCBs) in less than 4% of the samples taken. Fish samples taken at 9 of these 17 locations, and analyzed for the same compounds, showed a higher frequency of detectable contaminants. The most common compound found in fish was DDE, which was found in 51% of the samples at levels up to 512 ng/g. alpha-BHC was present at concentrations of 5 to 27 ng/g in 36% of the fish samples, and DDD was found at levels of 5 to 60 ng/g in 14%. Four other compounds, DDT, dieldrin, PCB, and trans-nonachlor, were detected in fish at relatively low concentrations in less than 10% of the samples. This survey, thus, indicated little contamination by organochlorine pesticides or PCBs in the wetland habitats of this region.     

Simultaneous determination of 20 pharmacologically active substances in cow's milk, goat's milk, and human breast milk by gas chromatography-mass spectrometry

This paper reports a systematic approach to the development of a method that combines continuous solid-phase extraction and gas chromatography-mass spectrometry for the simultaneous determination of 20 pharmacologically active substances including antibacterials (chloramphenicol, florfenicol, pyrimethamine, thiamphenicol), nonsteroideal anti-inflammatories (diclofenac, flunixin, ibuprofen, ketoprofen, naproxen, mefenamic acid, niflumic acid, phenylbutazone), antiseptic (triclosan), antiepileptic (carbamazepine), lipid regulator (clofibric acid), β-blockers (metoprolol, propranolol), and hormones (17α-ethinylestradiol, estrone, 17β-estradiol) in milk samples. The sample preparation procedure involves deproteination of the milk, followed by sample enrichment and cleanup by continuous solid-phase extraction. The proposed method provides a linear response over the range of 0.6-5000 ng/kg and features limits of detection from 0.2 to 1.2 ng/kg depending on the particular analyte. The method was successfully applied to the determination of pharmacologically active substance residues in food samples including whole, raw, half-skim, skim, and powdered milk from different sources (cow, goat, and human breast).     

Degradation of Prototype Pesticides Submitted to Conventional Water Treatment Conditions: The Influence of Major Parameters

The behavior of several pesticides in aqueous solution, namely bifenthrin, amethrin (pyrethroid insecticides), endosulfan and endosulfan sulfate (organochlorine pesticides), disulfoton, methyl pyrimiphos, and phorate (organophosphorus pesticides), submitted to the conditions typically employed in water treatment stations was investigated. Continuous pesticide depletion was monitored by solid-phase microextraction sampling followed by gas chromatography–mass spectrometry analysis. The influence of major parameters (sodium hypochloride concentration, solution pH, and exposure time to ultraviolet (UV) light) was, thus, adequately established via two complementary approaches: factorial (2³, three variables—two levels) and Doehlert designs. Hence, the sodium hypochloride concentration and the solution pH produced distinct effects depending on the pesticide evaluated (for instance, acidic and basic media caused increasing rates of degradation for the organophosphorus/pyrethroid and organochlorine pesticides, respectively). Conversely, higher rates of degradation were achieved for all of the pesticides investigated when increased exposure times to UV radiation were employed. Finally, the exposure time to UV radiation that lead to complete degradation of disulfoton and endosulfan sulfate (organophosphorus and organochlorine pesticides, respectively) in aqueous media under ordinary conditions employed in water treatment stations was established; disulfoton and endosulfan sulfate were completely degraded after 10 and 40 h, respectively.     

Simple determination of 40 organophosphate pesticides in raw wool using microwave-assisted extraction and GC-FPD analysis

A validated analytical method for the multiresidue analysis of 40 organophosphate pesticides (OPs) and conversion products in raw wool has been developed. The method is based on the selective microwave-assisted extraction (MAE) of raw wool with acetonitrile and analysis of extracts by gas chromatography-flame photometric detector. The optimum MAE conditions were 20 min duration at 80 °C with 30 mL of acetonitrile per gram of wool. A validation study was performed according to the European SANCO guidelines 10684/2009. Limits of detection and quantification for all pesticides tested were from 0.01 to 0.2 mg/kg and from 0.2 to 1.0 mg/kg, respectively. The average recoveries of pesticides spiked at different levels were in the range of 70-120% with relative standard deviations of ≤ 20%. The extraction performance was compared to the one obtained with a reference Soxhlet extraction. The method was also applied in the analysis of real wool (after field application) samples.     

Simultaneous gas chromatographic determination of carbofuran, metalaxyl, and simazine in soils

A method for extraction, cleanup, and simultaneous gas chromatographic detection of carbofuran, metalaxyl, and simazine in soils has been developed. Pesticide residues were extracted from soil with acetone containing 10% 0.2M HCl-KCl buffer (pH 2.0), cleaned up with methylene chloride-carbonate buffer (pH 10.7) solvent partitioning and solid-phase extraction on disposable silica gel columns, and quantitated with gas chromatography using a Supelcowax 10 megabore capillary column and a nitrogen-selective detector. Method limits of detection were 0.02 microgram/g for the 3 pesticides in surface soils (0-30 cm depths) and 0.02, 0.02, and 0.005 microgram/g in soils below 30 cm (subsoils) for carbofuran, metalaxyl, and simazine, respectively. Recoveries for carbofuran, metalaxyl, and simazine were 92.6 +/- 5.5, 93.6 +/- 5.0, and 88.4 +/- 6.7%, respectively, when soil samples were spiked with pesticide concentrations ranging from 0.02 to 2.0 micrograms/g.     

Determination of organophosphorus pesticides in fruit juices by matrix solid-phase dispersion and gas chromatography

A rapid multiresidue method was developed for the determination of nine organophosphorus pesticides in fruit juices. The analytical procedure is based on the matrix solid-phase dispersion (MSPD) of juice samples on Florisil in small glass columns and subsequent extraction with ethyl acetate assisted by sonication. Residue levels were determined by gas chromatography with nitrogen-phosphorus detection. Spiked blank samples were used as standards to counteract the matrix effect observed in the chromatographic determination. The NPD response for all pesticides was linear in the concentration range studied with determination coefficients >0.999. Average recoveries obtained for all of the pesticides in the different juices and fortification levels were >70% with relative standard deviations of <11%. The detection limits ranged from 0.1 to 0.6 microg/kg. The identity of the pesticides was confirmed by gas chromatography with mass spectrometric detection using selected ion monitoring. The proposed MSPD method was applied to determine pesticide residue levels in fruit juices sold in Spanish supermarkets. At least one pesticide was found in most of the samples, although the levels detected were very low, far from the maximum residue levels established for raw fruit.     

Analysis of pesticide residues in eggs by direct sample introduction/gas chromatography/tandem mass spectrometry

Direct sample introduction (DSI) or "dirty sample injection" is a rapid, rugged, and inexpensive approach to large volume injection in gas chromatography (GC) for semivolatile analytes such as pesticides. DSI of complex samples such as eggs requires a very selective detection technique, such as tandem mass spectrometry (MS-MS), to determine the analytes among the many semivolatile matrix components that also appear. In DSI, the nonvolatile matrix components that normally would contaminate the GC system in traditional injection methods remain in a disposable microvial, which is removed after every injection. For example, 3 microg of nonvolatile residue typically remained in the microvial after an injection of egg extract using the DSI method. This analytical procedure involves the following: (i) weighing 10 g of egg in a centrifuge tube and adding 2 g of NaCl and 19.3 mL of acetonitrile (MeCN); (ii) blending for 1 min using a probe blender; (iii) centrifuging for 10 min; and (iv) analyzing 10 microL (5 mg of egg equivalent) of the extract using DSI/GC/MS-MS. No sample cleanup or solvent evaporation steps were required to achieve quantitative and confirmatory results with <10 ng/g detection limits for 25 of 43 tested pesticides from several chemical classes. The remaining pesticides gave higher detection limits due to poor fragmentation characteristics in electron impact ionization and/or degradation. Analysis of eggs incurred with chlorpyrifos-methyl showed a similar trend in the results as a more traditional approach.     

SBSE-GC-ECD/FPD in the analysis of pesticide residues in Passiflora alata Dryander herbal teas

Stir bar sorptive extraction (SBSE) in combination with GC-ECD/FPD analysis is here applied to the determination of the residues of 11 pesticides (hexachlorobenzene, lindane, chlorothalonil, parathion methyl, parathion ethyl, fenitrothion, malathion, dieldrin, alpha- and beta-endosulfan, and tetradifon) in herbal teas prepared with Passiflora alata Dryander spiked leaves. The method was optimized using spiked herbal teas in a range from 0.05 to 1 pg/microL for organochlorine pesticides and from 0.15 to 3 pg/microL for organophosphorus pesticides. The method is reproducible and repeatable with recoveries calculated from herbal teas prepared with spiked plant material versus spiked herbal teas, varying from about 30% for tetradifon to about 90% for parathion methyl and malathion. The limits of quantitation (LOQs) ranged from 0.017 pg/microL for lindane to 0.117 pg/microL for malathion.     

Application of isotope dilution gas chromatography-mass spectrometry in analysis of organochlorine pesticide residues in ginseng root

A highly accurate and precise method based on isotope dilution gas chromatography-mass spectrometry was developed for the determination of five matrix-bound organochlorine pesticides, namely, hexachlorobenzene and hexachlorocyclohexanes (alpha-, beta-, delta-, and gamma- isomers), in a reference sample of Panax gingseng. Identification of the analytes was confirmed under selective ion monitoring mode by the presence of two dominant ion fragments within the specific time windows (+/-1% of the relative retention time with respect to the calibration standards) and matching of relative ion intensities of the concerned ions in samples and calibration standards (within +/-5%). Quantification was based on the measurement of concentration ratios of the natural and isotopic analogues in the sample and calibration blends. To circumvent the tedious iterative process of exact isotope matching that is often used in isotope dilution mass spectrometry analysis, a single-point calibration procedure was adopted with the isotopic amount ratios in the sample and calibration blends close to unity (0.9-1.1). Under the described approach, intraday and interday repeatability of replicate analyses of organochlorine pesticides in the ginseng root sample were below 1.4%. The expanded relative uncertainty ranging from 4.0 to 6.5% at a coverage factor of 2 was significantly lower than those of conventional gas chromatographic methods using other calibration techniques (internal or external standards). A deviation of less than 2.0% from the certified values was achieved when applying the developed method to determine hexachlorobenzene, alpha-, and beta-hexachlorocyclohexane in a certified reference material (CRM), BCR-CRM 115. Because of the unavailability of relevant CRMs of herbal origins, the concerned ginseng root sample, after verification of the "true values" of the concerned organochlorine pesticides by the valid primary method, is suitable for serving as an in-house reference material for quality assurance and method validation purposes.     

Assisted distillation cleanup of pesticide residues in animal fats: new beadless distillation tube

A new assisted distillation tube has been developed which contains no glass beads or glass wool. The sample is injected into the top of the tube, and a septum is not required. Large ground-glass joints (10/19) are used at the gas inlet and at the Florisil trap connection for maximum strength. Existing assisted distillation apparatus was easily modified to accept the new tubes. Recoveries of 9 organochlorine pesticides from butter and cattle fat ranged from 87 to 104% at a tube temperature of 230 degrees C and a nitrogen flow rate of 250 mL/min. No significant change occurred in recoveries of 8 of the 9 pesticides after 85 uses of the beadless tube. Only the recovery of HCB from butter decreased, from 95 to 80%, after 51 runs. The new tube was compared with the Unitrex glass bead-packed concentric tube at flow rates of 230, 400, and 600 mL nitrogen/min. Recoveries from the Unitrex tube were similar to those of the beadless tube for all pesticides except DDT which was significantly lower, indicating incomplete distillation at 250 mL/min and possible partial breakdown at 400 and 600 mL/min. A procedure is introduced for pressurized solvent washing of distillation tubes. This procedure is more efficient than vacuum washing.