Influence of heating history on dynamic viscoelastic properties and dimensions of dry wood

To obtain new information about the mechanical and physical properties of dry wood in unstable states, the influence of heating history on viscoelastic properties and dimensional changes of dry wood in the radial, tangential, and longitudinal directions was studied between 100° and 200°C. Unstable states of dry wood still existed after heating at 105°C for 30 min and were modified by activated molecular motion in the first heating process to temperatures above 105°C. This phenomenon is thought to be caused by the unstable states reappearing after wetting and drying again. Dry wood components did not completely approach the stable state in the temperature range tested, because they did not entirely surpass the glass transition temperatures in most of the temperature range. In constant temperature processes at 135° and 165°C, E′ increased and E″ decreased with time regardless of the direction. This indicated that the unstable states of dry wood components were gradually modified with time at constant temperatures. On the other hand, anisotropy of dimensional change existed and dimension increased in the longitudinal direction, was unchanged in the radial direction, and decreased in the tangential direction with time at constant temperatures. Part of this report was presented at the 13th Annual Meeting of the Chubu Branch of the Japan Wood Research Society, Shizuoka, August 2003     

Thermal-softening properties and cooling set of water-saturated bamboo within proportional limit

Thermal-softening properties and cooling set of water-saturated bamboo were investigated using stressrelaxation measurements in heating and cooling processes, followed by residual deflection measurement. In the heating process, an obvious decrease in relative relaxation modulus due to thermal-softening of lignin was found at around 60°C. On the other hand, no clear change in the relative relaxation modulus was recognized in the cooling process. After the cooling process, about 65% and 75% of residual set was measured when the specimen was loaded on the epidermis and endodermis side, respectively. Also, residual set depended on the maximum temperature reached in the heating process and the unloaded temperature in the cooling process. From these results, it was deduced that the glass transition of lignin from the rubbery to glassy state is important to fix the deformation. Comparing thermal-softening behavior between bamboo and wood, the relative relaxation modulus of wood decreased steeply at higher temperatures than for bamboo. On the other hand, while about 75% of residual set was also found for wood, almost the same as for bamboo, the recovery of deformation with time was larger for wood than for bamboo. Part of this article was presented at the 53rd Annual Meeting of the Japan Zairyou Society, Okayama, May 2004     

Physical and mechanical properties and colour changes of fast-growing Gympie messmate wood subjected to two-step steam-heat treatments

This study aimed to evaluate physical and mechanical properties and colour changes of fast-growing Gympie messmate wood subjected to two-step steam-heat treatments. To achieve this, Gympie messmate wood was thermally treated under different conditions. Combined steam (127°C and ～0,1471 MPa) and heat treatments in an oven (180–240°C for 4 hours) were performed. Physical and mechanical properties were evaluated by weight loss, equilibrium moisture content, specific gravity, volumetric and linear swelling and static bending tests, while colour changes were studied using CIEL*a*b* technique. The main findings showed that the steam pre-treatment in autoclave influenced most of the technological properties evaluated, mainly for heat treatments performed in low temperatures (180–200°C). The most significant changes after thermal treatments were observed for dimensional stability, which increased as a function of temperature of treatment. On the other hand, mechanical strength of thermally modified wood was significantly affected, while stiffness did not change. Colour modifications due to the application of two-step steam-heat treatments confirm the possibility to using these samples for aesthetic purposes.     

Compression behaviors of acetylated wood in organic liquids. Part I. Compression in equilibrium conditions

The radial compression behaviors of acetylated cedar wood were measured in various liquids. The compressive Young’s modulus (E) of acetylated wood was reduced by soaking in water, toluene, and acetone, but it was always greater than that of water-swollen unmodified wood at the same swelling level. The behaviors of acetone-swollen unmodified wood were similar to those of acetylated wood rather than those of water-swollen unmodified wood. These results indicated that the swelling of hydrophobic wood components had a lesser influence on the E of wood than the water-swelling of unmodified hydrophilic components. After large compression (ε > 45%), a part of the strain remained unrecovered because of irreversible mechanical deformation. Since the remaining strain was smaller in the wood specimens indicating greater stress relaxation, it was assumed that the viscoelastic deformation of amorphous matrix components is important for lesser irreversible deformation and effective shape recovery of wood. In contrast with water-swollen unmodified wood, the acetylated wood and acetone-swollen unmodified wood exhibited greater shape recovery despite their relatively higher E. This suggested that the swelling of hydrophobic wood components reduced the viscosity of the matrix rather than its elasticity, resulting in more effective shape recovery with lesser softening.     

Strength properties of thermally modified softwoods and its relation to polymeric structural wood constituents

Thermal modification at relatively high temperatures (ranging from 150 to 260 °C) is an effective method to improve the dimensional stability and resistance against fungal attack. This study was performed to investigate the impact of heat treatment on the mechanical properties of wood. An industrially-used two-stage heat treatment method under relative mild conditions (< 200 °C) was used to treat the boards. Heat treatment revealed a clear effect on the mechanical properties of softwood species. The tensile strength parallel to the grain showed a rather large decrease, whereas the compressive strength parallel to the fibre increased after heat treatment. The bending strength, which is a combination of the tensile stress, compressive stress and shear stress, was lower after heat treatment. This decrease was less than the decrease of only the tensile strength. The impact strength showed a rather large decrease after heat treatment. An increase of the modulus of elasticity during the bending test has been noticed after heat treatment. Changes and/or modifications of the main wood components appear to be involved in the effects of heat treatment on the mechanical properties. The possible effect of degradation and modification of hemicelluloses, degradation and/or crystallization of amorphous cellulose, and polycondensation reactions of lignin on the mechanical properties of heat treated wood have been discussed. The effect of natural defects, such as knots, resin pockets, abnormal slope of grain and reaction wood, on the strength properties of wood appeared to be affected by heat treatment. Nevertheless, heat treated timber shows potential for use in constructions, but it is important to carefully consider the stresses that occur in a construction and some practical consequences when heat treated timber is used.     

The effect of lignin on the bending properties and fixation by cooling of wood

To clarify the effects of lignin on the fixation of bending deformation by cooling, cooling set for delignified woods with various lignin residues were investigated to compare with mechanical and dynamic viscoelastic properties. Bending tests showed that steep reductions occurred in the modulus of elasticity and modulus of rupture with delignification during the initial stage of delignification. The dynamic viscoelastic measurements revealed that the peak temperature of tan δ due to micro-Brownian motion of lignin was reduced with delignification, and the peak disappeared in the temperature range of 5°–100°C for the specimens that had lost more than 21% of their weight. On the other hand, no clear change in residual set was found in the range of 0%–15% of weight loss in spite of a marked reduction in lignin content. Subsequently, set decreased steeply for the specimens delignified beyond 15% of weight loss. It was suggested that cooling set is not determined solely by lignin content but is influenced by changes in the quality of lignin due to delignification. Lignin quality affects the balance of the elastic potential to recover from deformation and its viscosity, which is an indication of resistance against flow. Part of this report was presented at the 57th Annual Meeting of the Japan Wood Research Society, Hiroshima, August 2007     

Effect of thermo-hydro-mechanical densification on microstructure and properties of poplar wood (<Emphasis Type="Italic">Populus tomentosa</Emphasis>)

This study aimed at developing a thermo-hydro-mechanical (THM) processing to compress poplar wood and investigating the effects of high temperature, moisture, and pressure during the THM processing on the changes in microstructure, porosity, mechanical properties, and dimensional stability of compressed poplar wood. The variations in these properties were correlated and their mathematical relations were determined. Poplar woods with high moisture content were compressed using different pressures at a temperature of 160 °C for different periods. The compression level was characterized by the volume compression ratio (CR), which is defined as the ratio of the compression volume and the original volume of sample before and after THM processing. The obtained results indicated that the high pressure of THM process caused the collapsing of wood cell lumens and the developing of a certain amount of fractures in the cell wall. The damage level of wood cells increased with increasing pressure and time. Moreover, the pressure narrowed the cell lumens, which decreased significantly the pore volume in wood substrate. The pore size distribution shifted from the level of macropores to those of mesopores and micropores after THM process. The THM process created superior mechanical property, especially for those with higher CR. Besides, it was revealed that the process decreased dramatically the set recovery of treated woods and improved their dimensional stability. A significant improvement was achieved in terms of the mechanical and physical properties of compressed poplar wood via the structural reformation during the THM process.     

Effect of hydro-thermal treatment of green beech wood on its chemical and physco-mechanical properties

Summary Preliminary investigations were carried out aiming at the establishment of relationships between chemical, physical, and mechanical properties of beech wood under the influence of heating in water at 50°C and 100°C at pH values from 2.8 to 8.5 and with heating times up to 25 hours. It was found that heating of beech wood in water at 50°C does not produce remarkable changes in its properties. When green wood was heated at 100°C, insignificant changes in its density, shrinking, and -cellulose content were observed, whereas a considerable decrease in strength was found when tested in a wet state. It was further observed that on prolonged heating, the reactions of the wood and the solutions used as a heating medium under-went distinct changes, attaining an equivalent value approximating the final pH of the wood.     

Improvements in dimensional stability and lightfastness of wood by butyrylation using microwave heating

Microwave heating was used as the heat source for butyrylation of wood with the aim of reducing the reaction time. The photostability and dimensional stability of butyrylated wood were also investigated in this study. Chemical changes of wood were confirmed by cross polarization/magic angle spin ¹³C-nuclear magnetic resonance and diffuse reflectance infrared Fourier transform spectroscopy (DRIFT) after butyrylation by microwave heating. Results from DRIFT with the Si-Carb sampling technique revealed that, using microwave heating, a higher degree of butyrylation of maple wood occurred in the middle of the specimen than on the outer surface. The increase in yellowness index of butyrylated wood treated with microwave heating was much less than that of untreated wood after the lightfastness test, indicating that photoyellowing of wood is effectively inhibited by butyrylation using microwave heating. The dimensional stability of wood was also improved after modification.     

Effect of intermittent heat treatment on crystallinity in wood cellulose

The effect of intermittent heat treatment on cellulose crystallites in wood was studied to evaluate quantitatively the changes of crystallinity induced by intermittent and continuous heating. The changes in crystallinity were found to be strongly affected by the intermittent heat treatment. The increased crystallinity, the width of the crystals, and the piezoelectric properties were the same for the first intermittent heating as for continuous heating. Further intermittent heating for the same time duration and temperature had no effect on the above properties, probably due to the stopping of the thermal reaction during the interval. Our results suggested that intermittent heat treatment has certain critical cooling temperatures that stop the thermal reaction and are closely related to the duration of the interval. Samples once exposed to a certain duration of heat treatment and then cooled need more time, about twice that of the first duration of intermittent heating compared with continuous heating, to reach maximum crystallinity in wood cellulose.     

Effect of thermal modification temperature on the mechanical properties,dimensional stability,and biological durability of black spruce (Picea mariana)

This study was aimed at evaluating the effect of thermal modification temperature on the mechanical properties, dimensional stability, and biological durability of Picea mariana. The boards were thermally modified at different temperatures 190, 200 and 210 °C. The results indicated that the thermal modification of wood caused a significant decrease in the modulus of rupture (MOR) after 190 °C, while the modulus of elasticity (MOE) seemed less affected with a slight increase up to 200 °C and slight decrease with further increase in temperature. The hardness of the thermally modified wood increased in the axial direction. This increase was also observed in tangential and axial directions but at a lesser extent. The final value was slightly higher in axial direction and lower in radial and tangential directions compared to those of the untreated wood. Dimensional stability improved with thermal modification in the three directions compared to the dimensional stability of unmodified wood. The fungal degradation results showed that the decay resistance of thermally modified wood against the wood-rotting fungi Trametes versicolor and Gloephyllum trabeum improved compared to that of the untreated wood. By contrast, the thermal modification of P. mariana had a limited effect on the degradation caused by the fungus Poria placenta.     

Preliminary study of viscoelastic properties of MAPP-modified wood flour/polypropylene composites

Viscoelastic properties of maleated polypropylene (MAPP)-modified wood flour/polypropylene composites (WPC) were investigated by both a compression stress relaxation method and dynamic mechanical analyses (DMA). Three wood to polymer ratios (40:60, 60:40, and 80:20) and five MAPP loading levels (0, 1, 2, 4 and 8%) were used to study their effects on the viscoelastic properties of MAPP-WPC. The results show that: 1) higher wood to polymer ratio corresponds to higher stress relaxation levels for unmodified WPC. The modification with MAPP has an obvious effect on the stress relaxation of MAPP-WPC at higher wood to polymer ratios (60:40 and 80:20), but almost no effect at the 40:60 wood to polymer ratio. The optimal MAPP loading level for the wood to polymer ratio of 60:40 appears at 1%; 2) the storage modulus reaches its maximum at a MAPP loading level of 1% for wood to polymer ratios of 40:60 and 60:40, while for the 80:20 wood to polymer ratio, a higher storage modulus is observed at higher MAPP loading levels, which is quite consistent with the stress relaxation results. The results suggested that a suitable loading level of MAPP has a positive effect on the viscoelastic properties of WPC at higher wood to polymer ratios. Excessive MAPP loading would have resulted in adverse effects.     

Real-time measurement of vibrational properties and fine structural properties of wood at high temperature

Vibrational properties and fine structural properties of wood were measured at high temperatures. Sitka spruce (Picea sitchensis Carr.) and Shioji (Japanese ash, Fraxinus spaethiana Lingelsh.) were used as specimens. The specimens, the system to support them, a magnetic driver, and a deflection sensor were in an electric drying oven, where vibration tests were conducted. The heating temperatures ranged from room temperature to 200 °C in 25 °C increments in both heating and cooling processes. X-ray diffractometry was carried out using positive sensitive proportional counter (PSPC) at room temperature to 200 °C in 20 °C increments in both heating and cooling processes. Received 13 December 1999     

Influence of stress level on compression deformation of wood in 170°C transient steam conditions

Abstract

Compression creep experiments of hybrid poplar (Populus deltoides×Populus trichocarpa) were performed in a pressurized vessel equipped with a heated hydraulic press. The viscoelastic response at various stress levels (2–7 MPa), a temperature of 170°C and transient steam conditions was studied. Moisture content and oven-dry density of compressed specimens were determined. While some recovery of compression strain occurred, compression resulted in permanent deformation and increased wood density. The influence of stress level on the amount of set recovery of compressive deformation was evaluated after 24 h water soaking. Applied stress level had a significant effect on the compression deformation. The initial strain, as well as creep strain, varied depending on the applied stress level. The highest oven-dry density was obtained at a stress level of 6.9 MPa. Lower stress levels resulted in lower moisture content after the compression process, while the equilibrium moisture content of compressed specimens was not significantly affected by stress level. Set recovery increased from 20% to 65% with increased stress level from 1.7 MPa to 4.1 MPa, then decreased to 53% for specimens compressed at 6.9 MPa. Moisture content after the compression process significantly affected the set recovery.     

Influence of heating and drying history on micropores in dry wood

To investigate the influence of heating and drying history on the microstructure of dry wood, in addition to the dynamic viscoelastic properties, CO₂ adsorption onto dry wood at ice.water temperature (273 K) was measured, and the micropore size distribution was obtained using the Horvath-Kawazoe (HK) method. Micropores smaller than 0.6 nm exist in the microstructures of dry wood, and they decreased with elevating out-gassing temperature and increased again after rewetting and drying. Dry wood subjected to higher temperatures showed larger dynamic elastic modulus (E′) and smaller loss modulus (E″). This is interpreted as the result of the modification at higher temperature of the instability caused by drying. Drying history influenced the number of micropores smaller than 0.6 nm in dry wood not subjected to high temperature, although the difference in the number of micropores resulting from the drying history decreased with increasing out-gassing temperature. A larger number of micropores smaller than 0.6 nm exist in the microstructure of dry wood in more unstable states, corresponding to smaller E′ and larger E″ than in the stable state. Consequently, unstable states are considered to result from the existence of temporary micropores in the microstructures of dry wood, probably in lignin. Part of this report was presented at the 55th Annual Meeting of the Japan Wood Research Society, Kyoto, March 2005, and at the 56th Annual Meeting of the Japan Wood Research Society, Akita, August 2006     

Influence of accessory substances,wood density and interlocked grain on the compressive properties of hardwoods

Wood samples of nine tropical hardwoods from Peru and sugar maple wood from Quebec were selected to perform moisture sorption tests associated with parallel-to-grain and tangential compression tests using a multiple step procedure at 25°C. Cold-water and hot-water extractives, sequential cyclohexane (CYC), acetone (ACE) and methanol (MET) extracts, ash content (ASH), wood density and interlocked grain (IG) were evaluated on matched samples too. Wood density corrected for the accessory substances was by far the major factor positively affecting the compressive properties of tropical hardwoods. The total amount of accessory substances is required in order to establish better relationships between physico–mechanical properties and density of tropical hardwoods. For a given wood density, the ultimate stress in parallel-to-grain compression was higher in tropical hardwoods than in temperate hardwoods. However, the compliance coefficients for both types of woods were quite similar. Sequential extraction with organic solvents was the most suitable method for evaluating the effect of extractives on compressive properties of tropical hardwoods. The CYC and ACE fractions did not contribute to variation in these mechanical properties. The substances dissolved in MET affected positively the compliance coefficient s ₁₁ in parallel-to-grain compression and negatively the compliance coefficient s ₃₃ in tangential compression. The IG decreased the compliance coefficient s ₁₁ but also decreased the ultimate stress in parallel-to-grain compression. Finally, variations in compressive properties that were due to changes in equilibrium moisture content (EMC) were clearly influenced by wood density; denser woods were more sensitive to changes in EMC than lighter woods.     

Effects of previous solvent exchange on acetylation of wood

Wood specimens were prepared in a swollen state using solvent exchange (PS) treatment. The swollen wood specimens were acetylated using acetic anhydride by heating at 80–120°C. At the beginning of heating, the weight percent gain (WPG) of PS-treated wood was greater than that of conventionally acetylated wood. This acceleration effect of the PS treatment was explained by the introduction of treating reagent into the wood polymers where the intermolecular hydrogen bonds were previously broken. On the other hand, the PS treatment had no influence on the final WPG and moisture sorption characteristics of acetylated wood. This indicated that the intrinsic reactivity of wood constituents was unaffected by the PS treatment. The acetylation of PS-treated wood produced greater bulking and slightly higher dimensional stability than that in the case of conventional acetylation at the same WPG. It was speculated that the expansion of cell lumina due to the PS treatment resulted in greater bulking on acetylation and lesser swelling of acetylated wood with moisture sorption.     

Effect of postcure conditions on the dynamic mechanical behavior of water-based polymer-isocyanate adhesive for wood

To study the effect of postcure conditions on the viscoelastic behavior of water-based polymer isocyanate adhesives for wood (API adhesive), dynamic mechanical analysis (DMA) was performed for a simplified model of API adhesives under various postcure conditions. These conditions were achieved by storing the samples at room temperature or by heating them in an oven. Fourier transform infrared (FT-IR) spectroscopy was performed to test for residual isocyanate groups (NCO) and isocyanate derivatives to elucidate the reaction mechanism under the postcure conditions. DMA revealed that the postcure conditions led to wide variations in the viscoelastic behaviors of API films. FT-IR analysis confirmed the decrease of residual isocyanate during postcure treatments. However, the complete consumption of isocyanate could not be achieved under the postcure conditions. A good correlation was found between the DMA result and the chemical changes in the API samples heated above 140°C. However, no correlation was observed in the case of the samples heated at temperatures less than 140°C. This implies that postcure conditions led to a difference in the reaction chemistry of API. Part of this article was presented at the 55th Annual Meeting of the Japan Wood Research Society, Kyoto, March 2005     

Effect of high temperature treatment on the mechanical properties of birch (Betula papyrifera)

The thermal treatment of wood is an alternative to the chemical treatment for preservation purposes. The heat treatment process improves wood’s resistance to decay and its dimensional stability. However, mechanical strength decreases as a result of heat treatment. Therefore, the treatment parameters have to be optimized to keep this loss at a minimum while improving other properties. Thermal treatment is new in North America, and its parameters are not yet adjusted for the Canadian species. Carrying out the parameter adjustment in an industrial furnace requires many trials which are costly in terms of material and man-power. A laboratory study was carried out to determine the effect of different parameters of the heat treatment on the mechanical properties of birch in order to optimize this process. A thermogravimetric analyzer was built to carry out the laboratory tests. The impact of the process parameters–such as maximum treatment temperature, holding time at this temperature, heating rate, and gas humidity–on the mechanical properties of birch was investigated. Temperature distributions in wood and in gas as well as the weight loss of wood were measured during the experiments. Afterwards, hardness, modulus of elasticity, modulus of rupture, and resistance to screw withdrawal of the samples were measured. The relation between the process parameters and the resulting mechanical properties was examined.     

基于应力波的活立木力学特性无损检测研究进展

活立木力学特性无损检测是科学评价森林质量的基础,为合理制定采伐作业时间、原木分级和木材高效利用提供有效依据.介绍应力波无损检测的基本原理以及基于应力波的活立木力学特性无损检测的研究进展,分析影响应力波在活立木中传播的因素,在此基础上阐述木材力学特性变化的原理以及基于应力波技术的木材力学特性季节动态变化检测的现状和意义,提出应力波检测活立木性质存在的问题,针对其存在的问题提出几点建议.