Effect of partial replacement of gum arabic with carbohydrates on its microencapsulation properties.

Gum arabic solutions (10% w/v) were emulsified with soy oil at oil/gum ratios of 0.25-5.0. At oil/gum ratios <1.0, it was established that gum arabic could be partially replaced with a nonsurfactant carbohydrate. To assess different carbohydrates as replacers for gum arabic, emulsions and spray-dried emulsions of soy oil and mixed solutions (10% w/v) of gum arabic and a range of carbohydrate wall materials (oil/gum = 0.5) were prepared and analyzed. Maize starch and glucose were ineffective as partial replacers of gum arabic, but maltodextrins of various dextrose equivalence values (5.5-38) successfully replaced 50% of the gum arabic. The microencapsulation efficiency of the gum arabic/maltodextrin stabilized powders was further increased by increasing total solids of the feed to the dryer and by increasing the atomizer nozzle diameter.     

Homogenization conditions affect the oxidative stability of fish oil enriched milk emulsions: lipid oxidation

In this study fish oil was incorporated into commercial homogenized milk using different homogenization temperatures and pressures. The main aim was to understand the significance of homogenization temperature and pressure on the oxidative stability of the resulting milks. Increasing homogenization temperature from 50 to 72 degrees C decreased droplet size only slightly, whereas a pressure increase from 5 to 22.5 MPa decreased droplet size significantly. Surprisingly, emulsions having small droplets, and therefore large interfacial area, were less oxidized than emulsions having bigger droplets. Emulsions with similar droplet size distributions, but resulting from different homogenization conditions, had significantly different oxidative stabilities, indicating that properties of significance to oxidation other than droplet size itself were affected by the different treatments. In general, homogenization at 72 degrees C appeared to induce protective effects against oxidation as compared to homogenization at 50 degrees C. The results thus indicated that the actual composition of the oil-water interface is more important than total surface area itself.     

Protein-stabilized nanoemulsions and emulsions: comparison of physicochemical stability, lipid oxidation, and lipase digestibility

The properties of whey protein isolate (WPI) stabilized oil-in-water (O/W) nanoemulsions (d(43) ≈ 66 nm; 0.5% oil, 0.9% WPI) and emulsions (d(43) ≈ 325 nm; 0.5% oil, 0.045% WPI) were compared. Emulsions were prepared by high-pressure homogenization, while nanoemulsions were prepared by high-pressure homogenization and solvent (ethyl acetate) evaporation. The effects of pH, ionic strength (0-500 mM NaCl), thermal treatment (30-90 °C), and freezing/thawing on the stability and properties of the nanoemulsions and emulsions were compared. In general, nanoemulsions had better stability to droplet aggregation and creaming than emulsions. The nanoemulsions were unstable to droplet flocculation near the isoelectric point of WPI but remained stable at higher or lower pH values. In addition, the nanoemulsions were stable to salt addition, thermal treatment, and freezing/thawing (pH 7). Lipid oxidation was faster in nanoemulsions than emulsions, which was attributed to the increased surface area. Lipase digestibility of lipids was slower in nanoemulsions than emulsions, which was attributed to changes in interfacial structure and protein content. These results have important consequences for the design and utilization of food-grade nanoemulsions.     

Emulsion properties of sunflower (Helianthus annuus) proteins

Emulsions were made with sunflower protein isolate (SI), helianthinin, and sunflower albumins (SFAs). Emulsion formation and stabilization were studied as a function of pH and ionic strength and after heat treatment of the proteins. The emulsions were characterized with respect to average droplet size, surface excess, and the occurrence of coalescence and/or droplet aggregation. Sunflower proteins were shown to form stable emulsions, with the exception of SFAs at neutral and alkaline pH values. Droplet aggregation occurred in emulsions made with SI, helianthinin, and SFAs. Droplet aggregation and subsequent coalescence of emulsions made with SFAs could be prevented at pH 3. Calcium was found to cause droplet aggregation of emulsions made with helianthinin, at neutral and alkaline pH values. Treatments that increase conformational flexibility of the protein molecule improved the emulsion properties of sunflower proteins.     

Lentil and chickpea protein-stabilized emulsions: optimization of emulsion formulation

Chickpea and lentil protein-stabilized emulsions were optimized with regard to pH (3.0-8.0), protein concentration (1.1-4.1% w/w), and oil content (20-40%) for their ability to form and stabilize oil-in-water emulsions using response surface methodology. Specifically, creaming stability, droplet size, and droplet charge were assessed. Optimum conditions for minimal creaming (no serum separation after 24 h), small droplet size (<2 μm), and high net droplet charge (absolute value of ZP > 40 mV) were identified as 4.1% protein, 40% oil, and pH 3.0 or 8.0, regardless of the plant protein used for emulsion preparation.     

Influence of EDTA and citrate on physicochemical properties of whey protein-stabilized oil-in-water emulsions containing CaCl2

The influence of chelating agents (disodium ethylenediaminetetraacetate (EDTA) and sodium citrate) on the physicochemical properties of whey protein isolate (WPI)-stabilized oil-in-water emulsions containing calcium chloride was determined. The calcium-binding characteristics of EDTA and citrate at 30 degrees C were characterized in aqueous solutions (20 mM Tris buffer, pH 7.0) by isothermal titration calorimetry (ITC). EDTA and citrate both bound calcium ions in a 1:1 ratio, but EDTA had a much higher binding constant. Oil-in-water emulsions (pH 7.0) were prepared containing 6.94% (w/v) soybean oil, 0.35% (w/v) WPI, 0.02% (w/v) sodium azide, 20 mM Tris buffer, 10 mM CaCl(2), and 0-40 mM chelating agent. The particle size, apparent viscosity, creaming stability, free calcium concentration, and particle surface potential of the emulsions were measured. The chelating agents reduced or prevented droplet aggregation in the emulsions. When they were present above a certain concentration (>3.5 mM EDTA or >5 mM citrate), droplet aggregation was prevented. The reduction of aggregation was indicated by decreases in particle size, shear-thinning behavior, apparent viscosity, and creaming. Emulsions containing chelating agents had lower free calcium concentrations and more negatively charged droplets, indicating that the chelating agents improved emulsion stability by binding calcium ions. EDTA could be used at lower concentrations than citrate because of its higher calcium ion binding constant.     

Preparation and characterization of water/oil and water/oil/water emulsions containing biopolymer-gelled water droplets

The purpose of this study was to create water-in-oil (W/O) and water-in-oil-in-water (W/O/W) emulsions containing gelled internal water droplets. Twenty weight percent W/O emulsions stabilized by a nonionic surfactant (6.4 wt % polyglycerol polyricinoleate, PGPR) were prepared that contained either 0 or 15 wt % whey protein isolate (WPI) in the aqueous phase, with the WPI-containing emulsions being either unheated or heated (80 degrees C for 20 min) to gel the protein. Optical microscopy and sedimentation tests did not indicate any significant changes in droplet characteristics of the W/O emulsions depending on WPI content (0 or 15%), shearing (0-7 min at constant shear), thermal processing (30-90 degrees C for 30 min), or storage at room temperature (up to 3 weeks). W/O/W emulsions were produced by homogenizing the W/O emulsions with an aqueous Tween 20 solution using either a membrane homogenizer (MH) or a high-pressure valve homogenizer (HPVH). For the MH the mean oil droplet size decreased with increasing number of passes, whereas for the HPVH it decreased with increasing number of passes and increasing homogenization pressure. The HPVH produced smaller droplets than the MH, but the MH produced a narrower particle size distribution. All W/O/W emulsions had a high retention of water droplets (>95%) within the larger oil droplets after homogenization. This study shows that W/O/W emulsions containing oil droplets with gelled water droplets inside can be produced by using MH or HPVH.     

Stabilization of oil-in-water emulsions by beta-lactoglobulin-polyethylene glycol conjugates

The disulfide bonds of beta-lactoglobulin (beta-lg) were modified by oxidative sulfitolysis to generate beta-lgSO(3). The native protein (beta-lg) and the modified protein (beta-lgSO(3)) were conjugated to activated polyethylene glycol (PEG) to generate beta-lgPEG and beta-lgSO(3)PEG, respectively. Oil-in-water (o/w) emulsions containing 1% beta-lg or beta-lg conjugates were prepared at pH 2.8, 5.0, and 7.0. Emulsion droplet diameters and zeta potentials were measured. For the same emulsifier, emulsion droplet diameters decreased when emulsion pH increased. Zeta potentials of emulsion droplets increased with pH for beta-lg and beta-lgSO(3). Zeta potentials of beta-lgPEG and beta-lgSO(3)PEG approached zero, suggesting that the protein molecule was covered by PEG chains. Accelerated and 7-day storage stabilities at 21 degrees C of the emulsions were monitored. The emulsifying activity index (EAI) of beta-lgPEG was not significantly different from the EAI of beta-lg. The EAI of beta-lg was enhanced following sulfitolysis of beta-lactoglobulin. The emulsifying activity increased more when the oxidatively modified protein was conjugated to polyethylene glycol. Emulsions made with beta-lgSO(3)PEG were more stable than emulsions made with beta-lg, beta-lgPEG, or beta-lgSO(3) under accelerated stability study and for 7 days at 21 degrees C. The stability of o/w emulsions stabilized with beta-lgSO(3)PEG increased because individual droplets were better protected, against protein bridging or coalescence, by the thick adsorbed protein-PEG layer.     

Production and characterization of oil-in-water emulsions containing droplets stabilized by beta-lactoglobulin-pectin membranes

Oil-in-water emulsions containing droplets stabilized by beta-lactoglobulin (beta-Lg)-pectin membranes were produced using a two-stage process. A primary emulsion containing small droplets (d(32) approximately 0.3 microm) was prepared by homogenizing 10 wt % corn oil with 90 wt % aqueous solution (1 wt % beta-Lg, 5 mM imidazole/acetate buffer, pH 3.0) using a high-pressure valve homogenizer. The primary emulsion was then diluted with pectin solutions to produce secondary emulsions with a range of pectin concentrations (5 wt % corn oil, 0.45 wt % beta-Lg, 5 mM imidazole/acetate buffer, 0-0.22 wt % pectin, pH 3.0). The electrical charge on the droplets in the secondary emulsions decreased from +33 +/- 3 to -19 +/- 1 mV as the pectin concentration was increased from 0 to 0.22 wt %, which indicated that pectin adsorbed to the droplet surfaces. The mean particle diameter of the secondary emulsions was small (d(32) < 1 microm) at relatively low pectin concentrations (<0.04 wt %), but increased dramatically at higher pectin concentrations (e.g., d(32) approximately 13 microm at 0.1 wt % pectin), which was attributed to charge neutralization and bridging flocculation effects. Emulsions with relatively small mean particle diameters (d(32) approximately 1.2 microm at 0.1 wt % pectin) could be produced by disrupting flocs formed in secondary emulsions containing highly negatively charged droplets, for example, by sonication, blending, or homogenization. The particles in these emulsions probably consisted of small flocs containing a number of protein-coated droplets bound together by pectin molecules. These emulsions had good stability to further particle aggregation up to relatively high ionic strengths (< or =500 mM NaCl) and low pH (pH 3). The interfacial engineering technology used in this study could lead to the creation of food emulsions with improved physicochemical properties or stability.     

Production and characterization of O/W emulsions containing droplets stabilized by lecithin-chitosan-pectin mutilayered membranes

The possibility of producing stable oil-in-water (O/W) emulsions containing oil droplets surrounded by multiple layer interfacial membranes from food grade ingredients has been demonstrated. These emulsions were produced using a three stage process that relies on the adsorption of charged biopolymers to oppositely charged surfaces. Emulsions (0.5 wt % corn oil, 0.1 wt % lecithin, 0.0078 wt % chitosan, 0.02 wt % pectin, and 100 mM acetic acid, pH 3.0) containing oil droplets stabilized by lecithin-chitosan-pectin membranes were formed using this interfacial layer-by-layer deposition process. The droplets in these emulsions had good stability to aggregation over a wide range of pH values and salt concentrations (pH 4-8 at 0 mM NaCl and pH 3-8 at 100 mM NaCl). This technology could be extremely useful to the food industry for the creation of O/W emulsions with improved properties or novel applications, e.g., improved stability to environmental stresses, protection of labile substances, controlled release, and triggered release.     

Lipid oxidation in corn oil-in-water emulsions stabilized by casein,whey protein isolate,and soy protein isolate

Proteins can be used to produce cationic oil-in-water emulsion droplets at pH 3.0 that have high oxidative stability. This research investigated differences in the physical properties and oxidative stability of corn oil-in-water emulsions stabilized by casein, whey protein isolate (WPI), or soy protein isolate (SPI) at pH 3.0. Emulsions were prepared with 5% corn oil and 0.2-1.5% protein. Physically stable, monomodal emulsions were prepared with 1.5% casein, 1.0 or 1.5% SPI, and > or =0.5% WPI. The oxidative stability of the different protein-stabilized emulsions was in the order of casein > WPI > SPI as determined by monitoring both lipid hydroperoxide and headspace hexanal formation. The degree of positive charge on the protein-stabilized emulsion droplets was not the only factor involved in the inhibition of lipid oxidation because the charge of the emulsion droplets (WPI > casein > or = SPI) did not parallel oxidative stability. Other potential reasons for differences in oxidative stability of the protein-stabilized emulsions include differences in interfacial film thickness, protein chelating properties, and differences in free radical scavenging amino acids. This research shows that differences can be seen in the oxidative stability of protein-stabilized emulsions; however, further research is needed to determine the mechanisms for these differences.     

Rheology and stability of acidified food emulsions treated with high pressure

The stability and rheology of acidified model oil-in-water emulsions (pH 3.6 +/- 0.1) were evaluated before and after high-pressure treatments. Varying concentrations of canola oil (0-50% w/w), whey protein isolate, polysorbate 60, soy lecithin (0.1-1.5% w/w each), and xanthan (0.0-0.2% w/w) were chosen. Exposure to high pressures (up to 800 MPa for 5 min at 30 degrees C) did not significantly affect the equivalent surface mean diameter D[3,2], flow behavior, and viscoelasticity of the whey protein isolate and polysorbate 60-stabilized emulsions. Pressure treatments had negligible effects on emulsion stability in these systems, except when xanthan (0.2% w/w) was present in which pressure improved the stability of polysorbate 60-stabilized emulsions. Soy lecithin-stabilized emulsions had larger mean particles sizes and lower emulsion volume indices than the others, indicating potential instability, and application of pressure further destabilized these emulsions.     

Comparative evaluation of the emulsifying properties of phosphatidylcholine after enzymatic acyl modification

The ability of enzymatically synthesized structured phosphatidylcholine (PC) containing caprylic acid to form and stabilize oil-in-water emulsions prepared with different triglycerides [medium chain triglycerides (MCT), soybean oil, and enzymatically synthesized structured lipids] was examined and compared with natural soybean PC and deoiled lecithin. Emulsions were prepared with varying oil and emulsifier concentrations. The particle size distribution, creaming stability, and viscosity were measured for the evaluation of the emulsifying properties. With an increase in the oil concentration, there was an increase in particle size, viscosity, and creaming layer. With an increase in the phospholipid (PL) concentration, there was usually a decrease in particle size and an increase in viscosity, where the emulsion stability was increased. General emulsions prepared with structured lipids resulted in smaller particle sizes as compared to MCT and soybean oil. Deoiled lecithin was able to increase the viscosity more significantly and give smaller particle sizes as compared to the other emulsifiers, thus producing more stable emulsions. However, in certain cases, structured PC was superior to deoiled lecithin and soybean PC. This observation was made for emulsions prepared with soybean oil or structured lipid at an oil/water ratio of 10:90. At an oil/water ratio of 30:70, the deoiled lecithin performed better as compared to the other PLs with all oil types. However, structured PC produced more stable emulsions as compared to natural soybean PC in MCT and soybean oil.     

Influence of calcium, magnesium, or potassium ions on the formation and stability of emulsions prepared using highly hydrolyzed whey proteins

Oil-in-water emulsions (4 wt % soy oil) containing 4 wt % whey protein hydrolysate (WPH) (27% degree of hydrolysis) and different levels of calcium, magnesium, or potassium chloride were prepared in a two-stage homogenizer. Other emulsions containing 4 wt % WPH but including 0.35 wt % hydroxylated lecithin and different levels of the above minerals were similarly prepared. The formation and stability of these emulsions were determined by measuring oil droplet size distributions using laser light scattering and by confocal scanning laser microscopy and a gravity creaming test. Both lecithin-free and lecithin-containing emulsions showed no change in droplet size distributions with increasing concentration of potassium in the range 0-37.5 mM. In contrast, the diameter of emulsion droplets increased with increasing calcium or magnesium concentration >12.5 mM. Emulsions containing hydroxylated lecithin were more sensitive to the addition of calcium or magnesium than the lecithin-free emulsions. Storage of emulsions at 20 degrees C for 24 h further increased the diameter of droplets and resulted in extensive creaming in emulsions containing >25 mM calcium or magnesium. It appears that both flocculation and coalescence processes were involved in the destabilization of emulsions induced by the addition of divalent cations.     

Sensory evaluation of sodium chloride-containing water-in-oil emulsions

The sensory perception of water-in-oil emulsions containing a saline-dispersed aqueous phase was investigated. Manipulating saltiness perception was achieved by varying the mass fraction aqueous phase (MFAP), initial salt load, and surfactant concentration [(polyglycerol polyricinoleate (PgPr)] of the emulsions, with formulations based on a central composite design. Saltiness and emulsion thickness were evaluated using a trained sensory panel, and collected data were analyzed using response surface analysis. Emulsion MFAP was the most important factor correlated with increased salt taste intensity. Emulsifier concentration and interactions between NaCl and PgPr had only minor effects. Emulsions more prone to destabilization were perceived as saltier irrespective of their initial salt load. The knowledge gained from this study provides a powerful tool for the development of novel sodium-reduced liquid-processed foods.     

Elucidation of protein-lipid interactions in a lysozyme-corn oil system by Fourier transform Raman spectroscopy

Lysozyme (25% in D2O, corn oil, and their emulsions (10% w/w oil/D2O solution) were examined by Fourier transform Raman spectroscopy. Emulsions showed three layers, namely, top oil, middle cream, and bottom aqueous layers. Raman spectral analysis revealed hydrophobic interactions involving both protein and lipid components. Compared to lysozyme in D2O, the difference spectrum obtained after subtraction of oil from the cream layer spectrum showed reduced intensity of tryptophan bands at 760, 1013, 1340, and 1360 cm(-)(1), reduced intensity ratio of the tyrosine doublet at 850 and 830 cm(-)(1), and increased intensity of the C-H bending band at 1455 cm(-)(1). Compared to corn oil, the difference spectrum after subtraction of lysozyme from the cream layer spectrum indicated decreased intensity at 2855 cm(-)(1) (lipid CH(2) symmetric stretch) and 3011 cm(-)(1) (unsaturated fatty acid hydrocarbon chain =C-H stretch) and a higher intensity ratio of the C-H stretching band at 2900 cm(-)(1) to bands at 2885 and 2933 cm(-)(1). Spectra of the top and bottom layers resembled corn oil and lysozyme, respectively, except for changes in the D2O band. Raman spectroscopy can be used to detect structural changes in proteins, lipids, and D2O due to protein-lipid interactions.     

Impact of weighting agents and sucrose on gravitational separation of beverage emulsions

The influence of weighting agents and sucrose on gravitational separation in 1 wt % oil-in-water emulsions was studied by measuring changes in the intensity of backscattered light from the emulsions with height. Emulsions with different droplet densities were prepared by mixing weighting agents [brominated vegetable oil (BVO), ester gum (EG), damar gum (DG), or sucrose acetate isobutyrate (SAIB)] with soybean oil prior to homogenization. Sedimentation or creaming occurred when the droplet density was greater than or lower than the aqueous phase density, respectively. The weighting agent concentrations required to match the oil and aqueous phase densities were 25 wt % BVO, 55 wt % EG, 55 wt % DG, and 45 wt % SAIB. The efficiency of droplet reduction during homogenization also depended on weighting agent type (BVO > SAIB > DG, EG) due to differences in oil phase viscosity. The influence of sucrose (0-13 wt %) on the creaming stability of 1 wt % soybean oil-in-water emulsions was also examined. Sucrose increased the aqueous phase viscosity (retarding creaming) and increased the density contrast between droplets and aqueous phase (accelerating creaming). These two effects largely canceled one another so that the creaming stability was relatively insensitive to sucrose concentration.     

Effect of emulsifier on oxidation properties of fish oil-based structured lipid emulsions

The effects of the emulsifiers lecithin, Tween 20, whey protein isolate, mono-/diacylglycerols, and sucrose fatty acid ester on oxidation stability of a model oil-in-water emulsion prepared with enzymatically synthesized menhaden oil-caprylic acid structured lipid were evaluated. Oxidation was monitored by measuring lipid hydroperoxides, thiobarbituric acid reactive substances, and the ratio of combined docosahexaenoic acid (DHA) and eicosapentaenoic acid (EPA) contents to palmitic acid in the emulsion. After high-pressure homogenization, all emulsions, except those prepared with lecithin, had similar droplet size distributions. All structured lipid emulsions, except for the lecithin-stabilized emulsions, were stable to creaming over the 48-day period studied. Emulsifier type and concentration affected oxidation rate, with 0.25% emulsifier concentration generally having a higher oxidation rate than 1% emulsifier concentration. Overall, oxidation did not progress significantly enough in 48 days of storage to affect DHA and EPA levels in the emulsion.     

Production and characterization of O/W emulsions containing cationic droplets stabilized by lecithin-chitosan membranes

Oil-in-water emulsions containing cationic droplets stabilized by lecithin-chitosan membranes were produced using a two-stage process. A primary emulsion was prepared by homogenizing 5 wt % corn oil with 95 wt % aqueous solution (1 wt % lecithin, 100 mM acetic acid, pH 3.0) using a high-pressure valve homogenizer. This emulsion was diluted with aqueous chitosan solutions to form secondary emulsions with varying compositions: 1 wt % corn oil, 0.2 wt % lecithin, 100 mM acetic acid, and 0-0.04 wt % chitosan (pH 3.0). The particle size distribution, particle charge, and creaming stability of the primary and secondary emulsions were measured. The electrical charge on the droplets increased from -49 to +54 mV as the chitosan concentration was increased from 0 to 0.04 wt %, which indicated that chitosan adsorbed to the droplet surfaces. The mean particle diameter of the emulsions increased dramatically and the emulsions became unstable to creaming when the chitosan concentration exceeded 0.008 wt %, which was attributed to charge neutralization and bridging flocculation effects. Sonication, blending, or homogenization could be used to disrupt flocs formed in secondary emulsions containing droplets with high positive charges, leading to the production of emulsions with relatively small particle diameters (approximately 1 microm). These emulsions had good stability to droplet aggregation at low pH (< or =5) and ionic strengths (<500 mM). The interfacial engineering technology utilized in this study could lead to the creation of food emulsions with improved stability to environmental stresses.     

Identification of the wheat seed protein CM3 as a highly active emulsifier using a novel functional screen

Lyophilized albumin protein fractions were prepared from flour of four varieties of wheat: Triticum aestivum cvs. Mercia and Riband, Triticum aestivum var. spelta, and Triticum turgidum var. durum (Kamut). The dry powders were redissolved in sodium phosphate buffers at pH 3.0, 6.5, or 8.0 and at ionic strengths of 0.1 or 1.0 M to a concentration of 0.1% (w/v). Emulsions formed by sonication of protein solutions with n-hexadecane were aged at room temperature and separated into aqueous, interstitial, and interfacial phases. The distinct emulsion components were lyophilized and analyzed by RP-HPLC. A protein was observed to be preferentially located in the interfacial component and subsequently purified from a total albumin fraction and identified by N-terminal sequencing as CM3, an alpha-amylase inhibitor subunit. Measurement of the equilibrium surface tension of CM3 as a function of protein concentration demonstrated that it was at least as active as bovine beta-lactoglobulin, an established protein emulsifier. Furthermore, measurement of the surface dilational elastic modulus at an air/water interface demonstrated the formation of a viscoelastic film, while fluorescence and FT-IR spectroscopic measurements on adsorbed and nonadsorbed CM3 suggest that the secondary structure is essentially unchanged upon adsorption to an oil/water interface. It is concluded that functional screening is a valid approach to identify novel protein emulsifiers in complex mixtures.