Surface characteristics of electroless nickel plated electromagnetic shielding wood veneer

Wood is a kind of porous natural material with very poor electro-conductivity, and it has almost no function of electromagnetic shielding. The method of electroless nickel plating was used to produce wooden material with electrical and effective electromagnetic shielding properties. Ni-P alloy layer was obtained on wood surface. The surface feature of plated wood veneer was observed by SEM and the surface composition and microstructure of the layer under different conditions were investigated by EDS and XRD respectively. Meanwhile, the relevant surface resistivity and electromagnetic shielding effectiveness were measured. Correlations of the phosphorous content in the layer to the structure of Ni-P alloy, electro-conductivity and electromagnetic shielding of plated veneers were discussed. SEM photos showed that the surface of electroless nickel plated veneers were covered with Ni-P alloy layer entirely, which made wood veneers more like metal. At the same time, the results showed that with the decreasing of the phosphorous content in the layer, the microstructure of Ni-P alloy layer transformed to be microcrystalline and electro-conductivity and electromagnetic shielding effectiveness were improved. When the phosphorous content was less than 2.37wt pct in the layer, the microstructure of Ni-P alloy layer was microcrystalline structure and its sur- face resistivity and electromagnetic shielding effectiveness were nearly 0.5Ω/□ and 55-60dB respectively.     

无电解电镀法制备具有电磁屏蔽功能的木材-金属复合材料

利用无电解电镀的方法制备了导电且具有电磁屏蔽功能的木材-金属复合材料.探讨了镀液用量、施镀时间和施镀温度对复合材料的表面电阻率和电磁屏蔽效能的影响,同时利用能谱分析(EDS)、X射线衍射分析(XRD)和扫描电镜分析(SEM)方法分别测定了不同施镀温度下得到的各镀层的磷含量、微结构和表面形貌.实验结果表明,在镀液使用量为500mL,施镀时间为30min和施镀温度为62℃的最优条件下,所得镀层的导电性和电磁屏蔽效果最佳.而且发现,随着施镀温度的提高,镀层中磷含量缓慢增加.XRD分析表明不同温度所得各镀层的结构均为多晶结构,通过SEM分析,镀层均匀、连续且具有金属光泽,说明在pH值一定的条件下,施镀温度对镀层结构和表面相貌的影响很小.图7表3参11.     

Regeneration and reuse of exhausted solutions of electroless nickel plating wood veneer

The regeneration of exhausted solutions of electroless nickel plating wood veneer was realized using soluble calcium salt to precipitate and remove phosphite and then using fluoride to remove residual calcium ions from the solution. The effect of the pH value of the solution, treatment temperature and the molar ratio of calcium ions to phosphite ions on the removal efficiency of phosphite was investigated. Wood veneer was electroless plated using regenerated solutions. A coating with better electrical conductivity and electromagnetic shielding was obtained. __________ Translated from Journal of Northeast Forestry University, 2005, 33(3): 47–48 [译自: 东北林业大学学报, 2005, 33(3): 47–48]     

Electromagnetic shielding efficiency of the electric field of charcoal from six wood species

Six wood species were carbonized under various carbonization temperatures and nonoxygen conditions to obtained charcoal. The effects of wood species, rate of temperature rise, and carbonization temperature on the electromagnetic shielding efficiency (ESE) of the electric field were investigated. The wood species used in this study were Japanese cedar, China fir, western hemlock, red oak, fortune paulownia, and Taiwan acacia. Tested materials were carbonized in a high-temperature oven under the following conditions: rate of temperature rise 1°–5°C/min; carbonization temperature 500°–1100°C, with temperature intervals of 100°C; maximum temperature maintained for 1h; and flow rate of nitrogen 300ml/min. The electromagnetic insulation strength system was used to detect the ESE of the electric field of charcoal. It was found that western hemlock and fortune paulownia charcoal showed maximum ESE values of of 36 and 61dB generated at a carbonization temperature of 1000°C. The charcoals derived from four other wood species showed maximum ESE values of 28dB for Japanese cedar, 23dB for China fir, 32dB for red oak, and 38dB for Taiwan acacia, respectively, at a carbonization temperature of 1100°C. The ESE value for fortune paulownia charcoal was similar to those of metal nets. The relations between ESE and logarithmic values of resistivity (log) could be represented by a negatively exponential formula.Part of this report was presented at the 50th Annual Meeting of the Japan Wood Research Society, Kyoto, April 2000     

Effects of copper and cadmium on uptake and leakage of K(+) in birch (Betula pendula) roots

Uptake and leakage experiments were performed to study the effects of copper and cadmium on K(+) fluxes in birch (Betula pendula Roth) roots. Labeled rubidium ((86)Rb(+)) was used as a tracer for K(+). Plants were pretreated with Cu or Cd (0, 2, 5 or 25 microM) for 0-300 min and then transferred to radiolabeled nutrient solution (150 microM K(+)) with or without 2,4-dinitrophenol (DNP) to separate the effects of heavy metal on active and passive K(+) influxes. Passive K(+) influx was decreased by pretreatment with Cu but was only slightly affected by pretreatment with Cd. Pretreatment with 2 microM Cu increased active K(+) influx, whereas pretreatment with 25 microM Cu decreased active K(+) influx and intermediate Cu concentrations (5 microM) did not affect active K(+) influx. The pretreatment effects of Cu on active and passive K(+) influxes increased with increasing pretreatment time. During the first hour, pretreatment with Cd decreased active K(+) influx with increasing pretreatment time, whereafter recovery began. To measure K(+) efflux, birch plants were loaded with (86)Rb(+) for 7 days before being exposed to Cu or Cd (0, 1, 3, 5 or 10 microM) in unlabeled nutrient solutions for 24 h. Net efflux of K(+) was measured as (86)Rb(+)-activity in the nutrient solutions 24 h after a heavy metal had been introduced. Efflux of K(+) increased with increasing Cu or Cd concentration in the unlabeled nutrient solution.The data indicate that Cu and Cd affected K(+) influx differently and that recovery mechanism(s), which were induced shortly after heavy metal introduction, counteracted the heavy-metal induced inhibition of active K(+) influx. Efflux of K(+) from plant roots over a 24-h period indicated that Cu and Cd had similar effects on K(+) efflux. There was no evidence of a recovery mechanism counteracting the heavy-metal-induced inhibition of K(+) efflux.     

Study on sheet material made from zephyr strands V: Properties of zephyr strand board and zephyr strand lumber using the veneer of fast-growing species such as poplar

Zephyr strand board (ZSB) and zephyr strand lumber (ZSL) were produced using zephyr made from poplar veneer to investigate the greater utilization of low-density poplar as a structural material. These materials were then compared to ordinary plywood, laminated veneer lumber (LVL) from poplar veneer, lauan plywood, and particleboard. The bending properties (moduli of rupture and elasticity) of ZSB proved superior to those of poplar plywood: and ZSL produced from poplar veneer zephyr had bending properties greater than ordinary LVL from poplar veneer. Apparently, the conversion of the poplar veneer into zephyr material had a positive effect on bending properties. Additionally, poplar ZSB had bending properties superior to those of lauan particleboard and equal to those of lauan plywood. The internal bond strength of poplar veneer ZSB was nearly two times greater than that of lauan particleboard.Parts of this report were presented at the international symposium on the utilization of fast-growing trees, Nanjing, China, October 1994. Report IV appeared inMokuzai Kogyo 49:599, 1994     

Effects of fire-retardant treatment and wood grain on three-dimensional changes of sandwich panels made from bubinga decorative veneer

ABSTRACT

The effects of a fire-retardant treatment (FRT) and wood grain on three-dimensional changes of aircraft sandwich panels were evaluated. Unvarnished and varnished panels having the outer decorative layer made with bubinga (Guibourtia spp.) were studied. Half of the samples from each type of panel received an FRT (phosphate-based) on all three layers of the decorative plywood. The other half had the two inner layers treated and the outer layer untreated. Three different figures formed by the rotary cutting and grain orientation were identified and separately studied on veneer surfaces. Samples pre-conditioned to 20°C and 40% relative humidity (RH) underwent an adsorption (25°C, 90% RH) and then a desorption (25°C, 40% RH) treatments. Changes in moisture content (MC), swelling, shrinkage, roughness, and waviness were measured after each moisture exposure condition. The results showed that the FRT increased significantly MC, swelling, and shrinkage of unvarnished and varnished panels. This treatment as well as the type of wood figure affected roughness and waviness variations of unvarnished panels. However, the effects of these two factors were not noticeable once panels were varnished.     

微蚀废液中铜回收工艺研究

为了选择性回收酸性微蚀废液中的金属铜,采用电沉积方法对影响该工艺过程的电流效率和阴极板上铜的沉积形态等因素进行了研究。实验结果表明此工艺回收铜的最佳工艺条件为:电解时间2 h,铜离子浓度18～26g.L-1,温度40～50℃,电流密度2.4～3.0 A.dm-2。在该工艺条件下阴极区产铜的形态主要以板状为主,电流效率最高达到96%以上。     

污染砂质土壤酸化对铜和锌释放影响的模拟研究

砂质土壤上造林会引起土壤酸化,影响铜和锌的释放。本文用模拟方法研究了砂质耕地造林引起土壤酸化对土壤中铜和锌释放的影响。结果表明,酸化可明显改变土壤中铜和锌的化学形态,促使碳酸盐结合态铜和锌向交换态、有机质结合态和氧化物结合态形式转化,增加土壤铜锌的释放和淋出潜力,其中对锌的影响尤为明显。铜和锌溶解度明显增加的土壤 pH 分别为 3.8-4.5和 6.2-6.5。图3表2参14。     

Effect of furnish type and high-density raw material from mill residues on properties of particleboard panels

The purposes of this study were to examine the use of furniture mill residues containing high-density raw materials in particleboard production and to evaluate the effect of mixing several types of furnish on board performance. Wood wastes collected from the furniture industry in Japan containing matoa (Pometia pinnata), Douglas-fir (Pseudotsuga menziesii), and sugi (Cryptomeria japonica) with different particle shapes were prepared as raw materials for use in the manufacture of experimental particleboards. Seven board types and three mixed boards were manufactured with three replications. Methylene diphenyl diisocyanate (MDI) resin was applied at 6 % content in mat preparation. The pressing conditions were temperature of 180 °C, initial pressure of 3 MPa, and pressing time of 5 min. The target density was 0.72 g/cm³. This study showed that matoa particleboard had properties suitable for use in interior applications, although its properties were considered inferior compared with other particleboards. Improvement of matoa particleboard could be achieved by mixing with higher quality wood particles such as those from sugi or Douglas-fir. The furnish type used in this study affected board performance. All residues from furniture mills have the potential to be used for particleboard production, even when they contain different furnish types and wood species.     

Secretome analysis of the basidiomycete <Emphasis Type="Italic">Phanerochaete chrysosporium</Emphasis> grown on ammonia-treated lignocellulosic biomass from birch wood

Ammonia pretreatment is a promising technique for enhancing enzymatic saccharification of lignocellulosic biomass. However, an enzymatic cocktail suitable for the breakdown of pretreated biomass samples is still being developed. The basidiomycete Phanerochaete chrysosporium is a well-studied fungus with regard to bioconversion of lignocellulosic biomass. In the present work, we analyzed proteins secreted by P. chrysosporium grown on untreated and ammonia-treated birch wood meal. Fungal growth, xylanase activity, and extracellular protease activity increased in the media containing the ammonia-treated biomass; however, cellulase production decreased compared to that observed in the untreated biomass. Secreted extracellular proteins were separated by two-dimensional electrophoresis and identified by liquid chromatography ion–trap mass spectrometry. Fifty-five spots corresponding to secreted proteins were chosen for further analysis. In the culture with ammonia-treated biomass, the relative concentration of a xylanase belonging to glycoside hydrolase (GH) family 11 increased, while acetyl xylan esterases belonging to carbohydrate esterase family 1 decreased. Moreover, GH family 10 xylanases were promoted proteolysis in the culture of ammonia-treated biomass, leading to the loss of family 1 carbohydrate-binding modules. These results indicated that P. chrysosporium produced enzymes related to the recognition of structural changes on xylan with de-acetylation and introduction of nitrogen by ammonia pretreatment of birch wood meal.     

Prediction of timber bending strength on basis of bending stiffness and material homogeneity assessed from dynamic excitation

The potential of utilizing resonance frequencies corresponding to edgewise bending modes for predicting the bending strength of timber is investigated. The research includes measurements of axial and transversal resonance frequencies, laboratory assessment of density, static bending stiffness and bending strength of 105 boards of Norway spruce of dimensions 45?×?145?×?3,600?mm3. It is shown that E _b,1 , (MOE based on the resonance frequency of the first bending mode) gives a higher coefficient of determination to the bending strength than what E _a,1 (MOE based on the first axial resonance frequency) does. It is also shown that resonance frequencies corresponding to higher bending modes can be used in the definition of a new indicating property, the measure of inhomogeneity (MOI). This is a scalar value representing the lack of fit between the true, measured resonance frequencies and the expected (assuming homogeneity) resonance frequencies of a board. The results show that using the MOI as a third indicating property, in addition to E _b,1 and density, increases the coefficient of determination with respect to bending strength from R ²?=?0.69 to R ²?=?0.75.     

Comparative study on physical and mechanical properties of laminated veneer lumber and plywood panels made of wood from fast-growing <Emphasis Type="Italic">Gmelina arborea</Emphasis> trees

Laminated products, such as laminated veneer lumber (LVL) or plywood (PW), have become important recently. The objective of this study was to determine and compare properties of panels fabricated with veneers of Gmelina arborea trees in a fast-growth plantation and glued with phenol formaldehyde resin. The results showed that LVL and PW physical and mechanical properties are comparable to those of solid wood with a specify gravity of 0.60. Moreover, these panels can be cataloged into group 2 of PS 1–95 of the Voluntary Products Standard of the United States. The difference in physical properties was not statistically significant between LVL and PW panels, except for water absorption. Some mechanical properties, such as hardness and glue-line shear, modulus of rupture in perpendicular flexure, nail and screw withdrawal parallel, and perpendicular strength, were statistically different between LVL and PW. However, no differences were established for the modulus of elasticity, tensile strength parallel to the surface, or tensile strength perpendicular to the surface. The differences were attributed to the venners’ orientation in the panels studied.     

Effects of wood species and retention levels on removal of copper,chromium, and arsenic from CCA-treated wood using sodium hypochlorite

Chemical extraction, bioremediation, and electrodialytic processes have been extensively studied for removal of copper, chromium, and arsenic from wood treated with chromated copper arsenate(CCA). However,one problem has not been addressed: the effects of wood species and retention levels on remediation efficiency. The objectives of this study were to investigate the effects of wood species and retention levels on removal of copper,chromium, and arsenic from CCA-treated wood samples using sodium hypochlorite. Our results showed that sodium hypochlorite(Na OCl) was very effective for removal of copper, chromium, and arsenic from CCA-C treated milled wood samples for all three species used in this study. The Cu, Cr, and As extraction efficiencies for red pine were95 % Cu, 97 % Cr and 94 % As, for maple were 95 % Cu,97 % Cr, and 98 % As at 4.0 kg m-3retention levels, and for aspen were 95 % Cu, 92 % Cr, and 91 % As at9.6 kg m-3retention level, respectively. However, the results showed that wood species and initial retention levels of CCA-treated wood products played very important roles in terms of removal of Cu, Cr, and As.