Efficacy of didecyldimethylammonium chloride against subterranean termites (Isoptera) in Australia

A laboratory bioassay was conducted on the ability of didecyldimethylammonium chloride (DDAC) to protectPinus radiata D. Don wood specimens from attack by two of Australia's most economically important species of subterranean termite,Mastotermes darwiniensis Froggatt (Mastotermitidae) andCoptotermes acinaciformis (Froggatt) (Rhinotermitidae). Sapwood specimens ofP. radiata, treated to achieve nominal retentions of 0.5, 1.0, 2.0, 4.0 and 6.0 kg/m³ of active ingredient, were bioassayed against each of these termite species for four and eight weeks, respectively. Mean percentage mass loss data showed that between 2.0 and 4.0 kg/m³ of DDAC was necessary to protect specimens from significant attack by both species of termite. The usefulness of DDAC as a termiticide for timber, particularly in the above-ground situation, is discussed.With one table and one figure     

Termite resistance of DMDHEU-treated wood

Four field trials were conducted with wood modified with dimethyloldihydroxy-ethyleneurea (DMDHEU) in contact with subterranean termites. Trials 1 to 3 were conducted with Coptotermes acinaciformis (Froggatt); 1 and 2 in south-east Queensland, and 3 in northern Queensland, Australia. Trial 4 was conducted in northern Queensland with Mastotermes darwiniensis (Froggatt). Four timber species (Scots pine, beech, Slash pine and Spotted gum) and two levels (1.3 M and 2.3 M) of DMDHEU were used. The tests were validated. DMDHEU successfully prevented damage by C. acinaciformis in south-east Queensland, but not in northern Queensland. It also did not protect the wood against M. darwiniensis. Except for beech in trial 4, DMDHEU led to reduced mass losses caused by termite attack compared to the unmodified feeder stakes. Slash pine (in trials 1 and 3) and Spotted gum (in trial 1) presented low mass losses. Modification of Scots pine was more effective against termite damage than the modification of beech.     

Toxicity and antitermite activity of the essential oils from Cinnamomum camphora, Cymbopogon nardus, Melaleuca cajuputi and Dipterocarpus sp. against Coptotermes curvignathus

Efficacy of four different essential oils against the subterranean termite, Coptotermes curvignathus Holmgren, was assessed in various bioassays. Laboratory results indicate that the highest termite mortality was found in Dipterocarpus sp. essential oil after 24 h (LC₅₀ = 1.62 %) and the lowest in Melaleuca cajuputi (LC₅₀ = 4.60 %). The wood consumption in the filter paper treated with Dipterocarpus sp. oil is also smaller than for the other three essential oils tested. However, the other three essential oils also inhibited termite susceptibility of the specimens. Dipterocarpus sp. (keruing oil) was the most effective insect antifeedant and repellent against C. curvignathus. The results suggest that essential oils might have some beneficial activity of economic value and are considered good candidates for the development of new chemicals (repellents or antifeedants) for termite control.     

Variation in the natural termite resistance of teak (Tectona grandis Linn. fil.) wood as a function of tree age

? Tree age is one of the most important factors to affect the natural durability of wood.

? The purpose of this study was to determine the natural termite resistance of heartwood and sapwood of teak (Tectona grandis Linn. fil.) for trees aged 8, 30 and 51 years. Reticulitermes speratus Kolbe was employed as a test termite using a no-choice feeding method.

? The heartwood and sapwood of all of the trees tested exhibited antitermitic activity. Based on the mean mass loss due to termite activity, the sapwood and heartwood regions of 8-year-old trees are the most susceptible to termites while the heartwood regions of the 30-year-old trees showed termite resistance similar to the termite resistance of 51-year-old trees.

? The mass loss is moderately correlated with n-hexane extractive content, total extractive content, brightness and redness of the wood.

     

Termite resistance and color of heartwood of hinoki (Chamaecyparis obtusa) trees in 5 half-sib families in a progeny test stand in Kyushu, Japan

Hinoki (Chamaecyparis obtusa) wood has been used as a structural material in Japan because of its superior mechanical properties, its excellent durability and the beautiful color of its heartwood. Variations of termite resistance and compositions of extractives among hinoki trees have been reported. However, genetic variation of termite resistance and the effect of heartwood color on termite resistance remain unknown. In this study, we report the characteristics of termite resistance and color indexes (L*, a* and b*) of heartwood of hinoki half-sib families in a progeny test stand. The survival days of termites and the mass loss of samples of hinoki heartwood differed significantly among hinoki families. Families with red-color heartwood had larger termite resistance than families with yellow-color heartwood. The termite resistances of individual samples from two families with yellow-color heartwood were as small as that of Pinus densiflora. Larger a* and smaller b* induced larger termite resistance of heartwood. The effect of DBH (diameter at breast height) of hinoki trees on termite resistance of hinoki families was small.     

Effects of polyvinyl alcohol on leachability and efficacy of boron wood preservatives against fungal decay and termite attack

In this study, the use of polyvinyl alcohol (PVA) as boron fixative agent was investigated. Two levels of PVA (2.5 and 4%) were evaluated with disodium octaborate tetrahydrate (DOT) at three concentrations (1, 2 and 4% boric acid equivalent (BAE)) using a double vacuum impregnation process on Scots pine sapwood specimens. Leaching was performed according to a laboratory leaching procedure. Boron analysis using atomic absorption spectrometer showed a significant reduction in boron leachability for the samples treated with both concentrations of PVA when compared to the stand-alone boron treatment leading to boron retentions capable of preventing wood biological degradations. Decay resistance of the leached specimens was evaluated using the brown rot fungus Poria placenta. Even if complete protection was not fully achieved, an improvement in decay resistance was observed for the samples treated with DOT in presence of PVA. This leak of efficacy was attributed to a decrease in the biological activity of the complexed boron against fungi. Durability of treated wood against termite attack, evaluated using Reticulitermes santonensis, indicated a significant enhancement for the samples treated in presence of the fixative agent compared to the pure boron treatment.     

Effect of an oil heat treatment on the teachability and biological resistance of boric acid impregnated wood

Vegetable oils provide boron retention of about 30% of initial amount depending on oil drying properties. Linseed oil is the most efficient, followed by soybean oil and rapeseed oil. Durability of C. japonica and F. crenata wood specimens has been enhanced by application of linseed oil alone but not enough to reduce termite’s attack of Coptotermes formosanus. Treating wood with a 1.0% w/w boric acid solution prior to oil treatment protects C. japonica from termite and fungi degradations. Efficiency against termites is mainly due to boron retention by oil but hydrophobic oil also forms a barrier decreasing fungi penetration. Boron efficacy threshold around 0.7 kg/m³BAE, lower than classical boron treatments thresholds indicates that oil water-repellence reinforces boron biostatic effect.     

Fungal colonisation of outside weathered modified wood

Specimens of Scots pine sapwood (Pinus sylvestris L.) and beech wood (Fagus sylvatica L.) were treated with an amino-alkyl-functional oligomeric siloxane, a sodium water glass solution and 1,3-dimethylol-4,5-dihydroxyethylene urea (DMDHEU). Treated and untreated wood specimens were exposed outdoors without ground contact. After 9?months of outside exposure, all specimens showed discolouration caused by infestations of mould and staining fungi on the exposed wood surface. Fungi grown on the sample surface were isolated and identified by microscopic technique and sequencing of PCR-amplified DNA from the ITS region. Primarily, an infestation by ascomycetes and related deuteromycetes was found. The most dominant fungi were Trichoderma sp. and Epicoccum sp.. An infestation of Aureobasidium pullulans was only detected on untreated and DMDHEU-treated samples. There were only marginal differences of fungal infestation between the two wood species.     

Leachability,decay, and termite resistance of wood treated with metaborates

The formation of insoluble metaborates in wood was investigated by impregnating the wood with borax and metallic salts, after which their properties (e.g., leachability in running water and biological resistance) were evaluated. The solubility of three metaborates in acidic solutions was also evaluated. Double-diffusion treatment was carried out to form the precipitates of metaborates in sapwood specimens of Japanese cedar (Cryptomeria japonica) at room temperature. Water-saturated wood specimens were first impregnated by a saturated borax solution and then diffuse-penetrated with Zn²⁺, Ca²⁺, or Pb²⁺ solution. The precipitates of the three metaborates in the wood proved to be insoluble or hardly soluble in water by the leaching test. With the decay test using a brown-rot fungus (Fomitopsis palustris) and a white-rot fungus (Trametes versicolor) and with the termite test using a virulent subterranean termite (Coptotermes formosanus), the metaborate-treated woods showed generally good decay and termite resistance with negligible mass loss of the specimens. Particularly, the lead metaborate formed in the wood provided superb biological resistance against decay and termite attacks. In addition, the precipitates of these metaborates were found to be soluble in acidic solution, suggesting a way to remove these chemicals from wood when disposing of waste materials.     

Enhancement of the biological resistance of wood by phenylboronic acid treatment

Phenylboronic acid (PBA) was tested in terms of boron leachability from treated wood. In addition, the fungal and termiticidal efficacy of PBA-impregnated sugi (Cryptomeria japonica D. Don) wood was tested against the decay fungi Coriolus versicolor (L. ex Fr.) Quel. and Tyromyces palustris (Berk. et Curt) Murr., representing white-rot and brown-rot fungi, respectively, and the Formosan subterranean termite Coptotermes formosanus Shiraki. Ion chromatography analysis of hot water extracts of treated wood before and after leaching indicated that PBA is considerably resistant to water leaching, and saturation of the treatment solution increased the fixation ratio of boron in wood, whereas boric acid could not remain in wood impregnated even with the saturated solution. Decay test results revealed the excellent bioactive performance of PBA. Wood treated with 0.34% PBA solution was found resistant to both decay fungi, even after running-water leaching for 10 days and treatment with 1.00% PBA completely inactivated the Formosan subterranean termite for the leached specimens. Weight gain levels were 0.18% w/w (0.46kg/m³) and 0.99% w/w (2.49kg/m³) for these concentration levels, respectively, after being leached by running water. Contrary to the general belief that boron is a slow-acting toxicant against termites and unable to prevent mass loss of treated wood, PBA acted rapidly, and the mass loss caused by termites was low.This study was presented in part at the 47th annual meeting of the Japan Wood Research Society, Kochi, April, 1997     

Ice nucleation and frost resistance of Pinus canariensis seedlings bearing needles in three different developmental states

Frost resistance and ice formation in different developmental states of needles of P. canariensis seedlings were assessed. Regrowth after frost damage was used to determine the overall frost survival capacity. Two distinct freezing exotherms (E1, E2) were registered. E1 was between ?1.7 and ?2.0 °C. Initial frost damage (LT₁₀) was 1.5–2.7 °C below E1. E2 was between ?5.6 and ?6.0 °C, and either corresponded with LT₅₀ or occurred in between LT₁₀ and LT₅₀. Current year needles were less frost resistant than 1-year-old needles. The overall recuperation capacity of seedlings revealed that frost survival may be underestimated when only needle damage is assessed. Freezing of seedlings with or without roots had no effect on the frost resistance of needles but recuperation capacity was significantly affected. Seedlings survived ?10 °C during summer indicating that they withstand the lowest naturally occurring frosts in Tenerife.     

Termite resistance and wood-penetrability of chemically modified tannin and tannin-copper complexes as wood preservatives

We examined the ability of chemically modified tannin and tannin-copper complexes to penetrate wood and the ability of the treated wood to resist termites. Only the tannin-treated wood retained the agents after treatment. Wood with untreated mimosa tannin (MT) retained the least amount, followed by wood with resorcinolated tannin (RMT) and that with catecholated tannin (CMT). When RMT or CMT was mixed with ammonia-copper, the wood retained twice as much of these solutions as the MT -ammonia-copper solution. The degree of retention of RMT-NH₃-Cu and CMT-NH₃-Cu ranged from 268 to 326kg/m³. The solutions penetrated 2–13 mm from the tangential sections of the logs. We also measured the termite resistance conferred by these solutions. Most of the tannin-NH₃-Cu solutions showed contact lethality for termites in the contact toxicity test. However, the termites were fed cellulose treated with those solutions and most survived the oral toxicity test (14 days). Moreover, these solutions reduced the amount of damage to the wood by termites. However, the mortality rate of the termites during the eating-damage test (>21 days) did not reach 100% for any of the solutions except for RMT. As a result of the field stake test with the same log's used for the penetrability test, the mass loss of wood treated with RMT or CMT alone or with RMT + NH₃ + CuCl₂, was about one-third to one-half that of the controls. Because these solutions have good wood penetrability and good termite resistance, they have potential use as low-toxicity wood preservatives.     

Strength,decay and termite resistance of oriented kenaf fiberboards

The development of oriented fiberboards made from kenaf (Hibiscus cannabinus L.) and their suitability as a construction material has been investigated. Three different types of boards consisting of five layers with individual orientations were prepared using a combination of low molecular weight and high molecular weight phenol-formaldehyde (PF) resin for impregnation and adhesion purposes. Additional boards with the same structure were prepared using high molecular weight PF resin only. The mechanical properties of the boards have been examined as well as their resistance against fungal decay and termite attack. All kenaf fiberboards showed elevated mechanical properties compared with medium-density fiberboard made from wood fibers, and showed increased decay and termite resistance. Differences in the decay and termite resistance between the board types were caused by the presence of the low molecular weight PF resin for the impregnation of the fibers. No significant difference was found for the mechanical properties. The effect of the PF resin for impregnation was much clearer in fungal decay resistance than for termite resistance; however, fiber orientation had no effect on both decay and termite resistance of the specimens.     

Comparative effectiveness of two alkylammonium compounds as wood preservatives

This study describes a laboratory evaluation of the efficacy of two alkylammonium compounds [didecyldimethylammonium tetrafluoroborate (DBF) and didecyldimethylammonium chloride (DDAC)] when applied via vacuum impregnation or superficial treatment. Treated wood specimens were tested for their termite and microbial resistance under controlled laboratory conditions. The higher chemical retentions were needed to suppress the feeding by Coptotermes formosanus ≦3% mass loss in the multichoice test than in the no-choice test. The DBF and DDAC retention levels necessary to meet the performance requirement ≦3% mass loss after 12-week fungal exposure varied with wood species. The retention level of 3 kg/m³ for DBF and DDAC was generally high to keep the nondurable wood species free of decay. Although there was no difference between DBF and DDAC in the efficacy against decay and termite attack, the former slightly outperformed the latter as an antimold and antisapstain agent.     

Effects of heartwood extractive fractions of Thuja plicata and Chamaecyparis nootkatensis on wood degradation by termites or fungi

The effect of selective removal of extractives on termite or decay resistance was assessed with matched samples of Thuja plicata Donn ex D. Don and Chamaecyparis nootkatensis (D.Don) Spach heartwood. Samples were extracted using a variety of solvents and then exposed to the subterranean termite Coptotermes formosanus Shiraki in a no-choice feeding test or to the brown-rot fungus Postia placenta (Fr.) M. Larsen & Lombard in a soil bottle test. At the same time, the effect of naturally occurring variations in heartwood extractives on termite or decay resistance was evaluated by testing samples from the inner and outer heartwood of five trees of each species against C. formosanus and P. placenta and analyzing matched wood samples for their extractive content. The results suggest that the methanol-soluble extractives in T. plicata and C. nootkatensis play an important role in heartwood resistance to attack by C. formosanus and P. placenta. Total methanol-soluble extractive content of the heartwood was positively correlated with both termite and decay resistance; however, there was much unexplained variation and levels of individual extractive components were only weakly correlated with one another. Further studies are under way to develop a better understanding of the relationships between individual extractive levels and performance.     

化学处理法对竹材阻燃、抗菌和防腐的影响(英文)

研究了6种用于印度勒竹防护的制剂,主要用于阻燃、防火防腐、抗真菌和白蚁的腐蚀。考察了阻燃剂和新型环保防腐剂ZiBOC用于印度勒竹防护的协同作用。将裂开的竹片用质量分数为15%的6种防护组分处理,即按照印度标准方法测试火焰穿透性、可燃性和燃烧率。6种15%质量分数的组分分别为:1.硫酸铵+磷酸铵+ZiBOC;2.硫酸铵+ZiBOC;3.磷酸铵+ZiBOC;4.磷酸镁+焦硫酸镁+ZiBOC;5.磷酸镁+ZiBOC;6.焦磷酸镁+ZiBOC。结果表明,达到防护目的的不同化学组分的防护剂用量应为9～11.5kg/m3。用白腐菌的腐烂实验表明,配方为2、3、5和6的防护剂表现出较好的防腐作用(防护率达到95%,p0.05),而用褐腐菌其防护率约为43%～67%。采用经2～6配方处理过的样品均能抗第一、二期的白腐腐蚀,而第二期的白蚁对配方4处理过的样品有轻微的腐蚀作用。少数几种配方对材料的耐火性有提高。     

Control by ATR-FTIR of surface treatment of cork stoppers and its effect on their mechanical performance

Fourier transform infrared (FTIR) spectroscopy was applied to determine the type of surface treatment and dose used on cork stoppers and to predict the friction between stopper and bottleneck. Agglomerated cork stoppers were finished with two different doses and using two surface treatments: P (paraffin and silicone), 15 and 25?mg/stopper, and S (only silicone), 10 and 15?mg/stopper. FTIR spectra were recorded at five points for each stopper by attenuated total reflectance (ATR). Absorbances at 1,010, 2,916, and 2,963?cm^?1 were obtained in each spectrum. Discriminant analysis techniques allowed the treatment, and dose applied to each stopper to be identified from the absorbance values. 91.2% success rates were obtained from individual values and 96.0% from the mean values of each stopper. Spectrometric data also allowed treatment homogeneity to be determined on the stopper surface, and a multiple regression model was used to predict the friction index (If?=?Fe/Fc) (R ²?=?0.93).     

Resistance of gamma-irradiated sapwood of <Emphasis Type="Italic">Cryptomeria japonica</Emphasis> to biological attacks

Any means helpful for the promotion of termite feeding activity has potential for use in a matrix in termite bait application. Therefore, energy transfer by gamma irradiation is worthy of consideration for converting wood into termite-accessible material. Wood specimens gamma-irradiated at 100 kGy and at lower levels were tested for their degrees of polymerization (DP) of cellulose and biological resistance. The DP of cellulose adversely decreased with increased doses of gamma irradiation. Termite wood consumption rates, which were determined by laboratory tests using undifferentiated larvae (workers) of Coptotermes formosanus Shiraki, were significantly higher at 100 kGy than at other doses. On the other hand, the decay resistance of gamma-irradiated wood against the fungi Fomitopsis palustris (Berkeley et Curtis) Murrill and Trametes versicolor (L. ex Fr.) Quel did not vary by irradiation dose.     

Radial distribution of quinones in plantation teak (Tectona grandis L.f.)

? Quinones are primarily responsible for the natural durability of teak.

? The previous paper in this series reported on the natural termite resistance of teak trees of different ages (8-, 30- and 51-year-old trees). In this study, the radial distribution of quinones (tectoquinone, lapachol, desoxylapachol and its isomer) and other components in the ethanol-benzene (1:2) extract were measured by means of gas chromatography.

? Significant differences in desoxylapachol or its isomer content were found among the outer heartwood of 8-, 30- and 51-year old trees, as well as between the inner and outer parts of the heartwood.

? All toxic quinone contents were positively correlated with the total extractive content. The highest correlation degree was measured in the isodesoxylapachol content.

? Although linearly related, only modest correlations were observed between the natural termite resistance parameters and the content of tectoquinone and isodesoxylapachol.

     

Superheated steam treatment of rubberwood to enhance its mechanical,physiochemical, and biological properties

ABSTRACT

This research was aimed to investigate mechanical properties, color and cell-wall components changes, and durability of pre-dried rubberwood (Hevea brasiliensis) after superheated steam (SS) treatment. Wood samples were treated at different SS temperatures (140–180°C) for 1–3?h. The highest compression strength parallel-to-grain, hardness and impact strength were found for samples treated at 160°C for 3?h (30.7% higher than untreated), at 150°C for 1?h (26.6% higher than untreated) and at 150°C for 2?h (52.6% higher than untreated), respectively. The surface color became darker after each treatment in comparison with the untreated wood. The number of accessible hydroxyl groups decreased and the relative cellulose crystallinity increased with SS temperature, indicating decreased hygroscopicity of the treated wood. Also, SEM micrographs of wood surface showed consistent decrease in starch particles with treatment temperature. Both decay and termite resistances of treated rubberwood improved with treatment temperature. All the analyzes showed that dried rubberwood treated with SS had some improvements in the mechanical properties, decreased hygroscopicity, and increase resistance to decay.