软木聚结材料生产工艺的研究

为降低生产成本,采用MDI和VAE的混合胶压制软木聚结板.通过正交试验分析MDI和VAE混合质量比、施胶量、热压温度和时间对软木聚结板性能的影响.结果表明,在MDI中加入一定量的VAE,对软木聚结板的主要性能无显著影响;最佳工艺为:MDI和VAE质量比0.15,施胶量10%,热压温度150 ℃,热压时间30 min.     

麦秸/聚苯乙烯复合材料工艺参数研究

以麦秸和废旧聚苯乙烯塑料为原料,采用冷混-热压工艺,通过正交试验和单因子试验,研究热压时间、热压温度、复合材料密度、聚苯乙烯比例和施胶量等工艺参数对麦秸/聚苯乙烯复合材料性能的影响.结果表明:热压时间7 min、热压温度190℃、聚苯乙烯比例为35%、施胶量3%、复合材料密度0.6 g·cm-3和0.65 g·cm-3时,压制出的麦秸/聚苯乙烯复合材料各项物理力学性能指标达到刨花板国家标准(GB/T 4897.1-4897.7-2003)要求,确定了试验的最佳工艺参数和工艺条件.     

热压工艺对软木地板物理力学性能的影响

以软木粒子为主要原料,聚氨酯胶黏剂为粘结剂压制软木地板,探究热压温度、热压时间、施胶量对软木地板回弹率、抗拉强度、初始压缩度及残留压缩度等物理力学性能的影响规律,进而为改善软木制品质量、提高生产效率提供理论基础。研究结果表明,软木地板热压工艺参数为:热压温度120℃,热压时间12 min,施胶量9%,此优化工艺条件下热压的软木地板各项物理力学性能均满足相关国家标准要求。     

基于响应面优化竹单板泡沫铝复合材料工艺研究

以竹单板、泡沫铝为原材料,采用中温固化型酚醛树脂胶黏剂制备竹单板泡沫铝夹芯复合材料。应用单因素试验结合响应曲面法,探究施胶量、热压温度和热压时间三因素对复合材料静曲强度和胶合强度的影响规律,对制备工艺进行优化。结果表明:三因素按影响复合材料力学性能程度大小依次排序为施胶量热压温度热压时间。通过构建复合材料的力学性能与施胶量、热压温度和热压时间之间的回归方程模型,得出优化的制备工艺条件为:施胶量340 g/m~2、热压温度132℃、热压时间1.5 mm/min,在此条件下制得的复合材料静曲强度为122.6 MPa,胶合强度为3.20 MPa,测量误差在3%以内。     

芦苇碎料——木纤维复合板的工艺研究

通过试验确定了芦苇碎料—木纤维复合板的主要工艺参数。其结果表明:14 mm复合板的较优工艺参数为:木纤维比例30%,木纤维施UF胶、施胶量12%,芦苇碎料施MDI胶、施胶量5%,热压时间7 min,热压温度170℃。按照以上工艺条件压制的复合板性能可以达到刨花板国家标准的要求。     

超低密度生物质纤维基复合材料性能的研究

为了获得轻质高强的复合材料,以聚合物发泡技术与人造板工艺技术结合制备超低密度生物质纤维基复合材料,通过发泡手段使材料密度降低的同时提高材料的物理力学性能。重点研究发泡对复合材料力学性能的影响。研究结果表明:以碳酸氢钠为发泡剂对生物质纤维基复合材料进行发泡可以有效提高材料的物理力学性能。经方差和极差分析可知,本研究最佳工艺条件为:施胶量为25%、发泡剂加量6%、热压温度165℃、热压时间6min。     

工艺参数对稻壳-木刨花复合板内结合强度的影响

采用均匀实验设计方法,通过单因素及两因素间交互作用情况,探讨工艺参数对稻壳-木刨花复合板内结合强度(IB)的影响。在试验研究范围内,密度、芯层比例、芯层施胶量、热压温度、热压时间对复合板IB影响显著,表现为IB随密度的增大先增大后减小,随芯层比例和芯层施胶量的增加而增加,随热压温度和热压时间的增加而减小。当密度为0.77 g/cm3、芯层比例为60%~65%、芯层施胶量为4.5%、热压温度为170℃、热压压力为2.5 MPa、热压时间为20 s/mm时,在兼顾生产效率与生产成本的同时,能够获得IB良好的稻壳-木刨花复合板。     

生产工艺对巨尾桉/聚乙烯膜复合材料质量的影响

采用巨尾桉基材、胶合剂聚乙烯膜制备三层木塑复合材料,分析热压温度、热压时间、热压压力、施胶量这四个因素对复合材料胶合强度的影响。结果表明：在热压温度160℃、热压时间50s/mm、热压压力0.7MPa、施胶量为119g/m2的工艺条件下,巨尾桉/聚乙烯膜复合材料的胶合性能最优,能够达到II类胶合板标准。     

薄型竹丝刨花板生产工艺初探

以毛竹竹丝为原料,探讨了3mm薄型竹丝刨花板的生产工艺。采用正交试验方法,分析了板坯密度、热压温度、热压时间和施胶量对薄型竹丝刨花板性能的影响。试验结果表明,板坯密度和施胶量对板材的主要性能影响显著,而热压温度和热压时间无显著影响。本研究为薄型竹丝刨花板生产制定的生产工艺参数为:板坯密度0.65g/cm~3,热压时间6min,热压温度130℃,施胶量10%。     

竹席/竹碎料新型建筑模板制备工艺研究

将小径竹及竹材加工剩余物加工成一定规格的竹碎料。以竹碎料为芯层,以竹席为表层组成板坯,通过热压制备竹席/竹碎料新型建筑模板。采用正交试验,选取热压时间、热压温度和施胶量作为工艺因素,对竹席/竹碎料复合新型建筑模板制备工艺进行了研究。研究发现,施胶量对产品的各项性能指标的影响最显著,其次是热压时间和热压温度。通过分析得出优化工艺:热压时间70 s.mm-1,热压温度为170℃,施胶量为10%。     

Browsing Damage on Pine (Pinus sylvestris and P. contorta) by a migrating moose (Alces alces) Population in Winter: Relation to Habitat Composition and Road Barriers

In Scandinavia, moose (Alces alces L.) sometimes cause severe browsing damage to economically-important pine. Moose-vehicle accidents have spurred construction of fences along roads, and these may interfere with moose migration between summer and winter ranges, or the road alone may be a barrier. If this happens and moose build up along roads, landowners may suffer economically. Therefore, this study investigated whether roads, fences or other factors influence the use of young pine stands by moose. Eighty stands along roads in northern Sweden were evaluated in which individually-browsed branches were counted on 9972 pines. Moose browsing was not significantly related to birch (Betula pendula Roth, B. pubescens Ehrh.) density, nor did it differ between pines (Pinus contorta Douglas or P. sylvestris L.). However, increased pine density, site productivity and proximity to a highway were associated with increased browsing. Further large-scale studies are needed to understand moose habitat selection and the effects of roads.     

Effects of Root Freezing on the Physiology and Growth of Picea glauca,Picea mariana and Pinus banksiana Seedlings Under Different Soil Moisture Regimes

The root systems of 2-yr-old Picea glauca, Picea mariana and Pinus banksiana seedlings were submitted to various frost temperatures during an artificial frost to induce different levels of root damage. Frost-damaged and control seedlings were placed in a greenhouse under high and low soil moisture regimes. Seedling growth and physiology were evaluated periodically. Seedling survival was reduced when root damage reached levels of 60-80%. Root systems of all three species showed partial to total recovery by the end of the experiment. In general, root freezing damage caused reductions in seedling growth, with these reductions becoming less significant over time. Root damage had little to no effect on black spruce and jack pine seedling physiology, while white spruce CO 2 uptake decreased with increasing root damage. Shoot nitrogen content of all three species decreased slightly with increasing root damage.     

Stand Structure in Pine,Spruce and Deciduous Forests: A Comparison Between Finnish and Russian Karelia

This study investigated the stand structure in pine, spruce and deciduous forests in the border district of Finland and Russia. A total of 46 mature forest stands was selected as pairs, the members of each pair being as similar as possible with respect to their forest site type, age, moisture and topography. The stands were then compared between the two countries by means of basal areas and number of stems. The proportions of dominating tree species were 2-12% lower, and correspondingly the proportions of secondary tree species higher, in Russian forests. The density of the forest stock was also higher in each forest type in Russia. The forests in the two countries differed most radically in terms of the abundance of dead trees. The amount was two to four times higher in Russian deciduous and spruce forests, and in pine forests the difference was 10-fold. The stand structures indicated that Russian coniferous stands, in particular, were more heterogeneous than intensively managed pine and spruce stands in Finland.     

Growth and Terminal Bud Formation in Picea abies Seedlings Grown with Alternating Diurnal Temperature and Different Light Qualities

The root collar diameter and the height:diameter ratio are of particular importance in container-grown seedlings where a high density in the containers may produce spindly seedlings. Temperature regimes and light quality are known to affect plant growth. The aim of this study was to identify responses in Picea abies (L.) Karst. seedlings grown with light providing different red:far-red ratios and under temperature regimes with alternating day (DT) and night temperature (NT) from negative (DT < NT) to positive (DT > NT) difference (DIF) between DT and NT. Experiments were conducted in controlled environment chambers and in a daylight phytotron. Only limited thermoperiodic responses appeared in P . abies seedlings with respect to seedling height and dry weight accumulation. The formation of terminal buds, however, was clearly delayed in seedlings grown at negative DIF. The results indicate a requirement for day extension light that is high in far-red, to prevent terminal bud formation under natural short-day conditions. An extended study should be conducted to clarify the minimum level of light intensity and the optimal light quality needed to prevent terminal bud formation under natural short-day conditions.     

CAD与建筑设计的关系

本文分析了CAD在设计中引起的正面和负面影响,并进行了系统的阐述,从而使设计者在应用中能够保持客观的态度。     

Natural Regeneration in Clear-cuts: Effects of Scarification,Slash Removal and Clear-cut Age

The effects of soil scarification (mounding), slash removal and clear-cut age on the natural regeneration in clear-cuts was evaluated using data from four sites in southern Sweden. The treatments were carried out during a good seed and establishment year for birch ( Betula pubescens Ehrh. and B. pendula Roth). Scarification had the strongest positive effect on the density of naturally regenerated seedlings, especially in birch, but also in pine ( Pinus sylvestris L.) and spruce [ Picea abies (L.) Karst]. Slash removal had a positive effect on birch density. No statistically significant effect of clear-cut age was found. In addition, no statistically significant interactions between clear-cut age and scarification or slash removal were found. The ingrowth of field vegetation was the fastest in areas that were not scarified, less rapid in areas scarified on old clear-cuts, and the slowest after scarification in fresh clear-cuts. In conclusion, it may be possible to control the density of birch during a good establishment year for birch. If birch is desired, the best combination of treatments is to remove the slash and scarify; otherwise, these treatments should be avoided.     

Risk Perception Among Non-industrial Private Forest Owners

Based on an enquiry, risk perception among non-industrial private forest owners is described in relation to climate change and forestry hazards. Of the respondents, 11% took action to remedy the effects of climate change. Out of a given set, hazards were ranked according to each respondent's experience of recent substantial financial loss to the estate and in relation to his or her willingness to make investments aimed at risk reduction. For each hazard, the respondent assessed the risk in four classes ranging from very high to negligible risk. Six hazards were considered most problematic in all three aspects: browsing damage, falling timber prices, damage by wind, spruce bark beetle, root rot and pine weevil. A majority of the respondents claimed to take action to reduce the risk associated with at least one hazard, while 35% did not know whether they did. Excluding climate change, the need for decision support was the largest in relation to damage by wind owing to a combination of perceived high risk and a high level of ignorance in relation to whether risk-reducing measures were taken.     

Interactions in decomposition and N mineralization between tropical legume residue components

In situ produced plant residues contain a mixture of different plant components of varying quality. To assess synergistic or antagonistic interactions occurring during the decomposition and mineralization of such mixtures, individual plant parts (stems, leaves, leaf litter and roots) or the mixture of stems, leaves and leaf litter of the agroforestry species pigeonpea (Cajanus cajan) or of crop residues of peanut (Arachis hypogaea) or of the weed hairy indigo (Indigofera hirsuta) were incubated in pots for 19 weeks. Periodically, remaining plant residues were sieved out (>2 mm), weighed and N content as well as soil mineral N determined. Above- and below-ground residues of peanut decomposed fastest and showed the largest N release in agreement with their high N concentration and low-acid detergent fibre (ADF) : N ratio. Hairy indigo was hypothesized to be of lower quality than pigeonpea because of its high-polyphenol content. However, it decomposed faster than pigeonpea, largely because of the higher N and lower lignin concentration of its components. Ranking of individual plant components for N mineralization resulted in the following pattern, leaves > leaf litter > roots > stems. In mixtures of the different plant components a similar species order in decomposition was obtained, e.g. peanut > hairy indigo > pigeonpea. The amount of N released from the mixture was dominated by stem material that comprised 46–61% of the mixture. The interactions in mixtures were relatively small for peanut (generally high-quality components) as well as for pigeonpea (low proportion of high-quality components, i.e. N rich leaf material). However, a positive interaction occurred during later stages of N mineralization in the mixture of hairy indigo as it had a significant proportion of N rich components and absence of highly reactive polyphenols. Thus, for plants with low to intermediate chemical quality attributes, manipulating plant composition (e.g. by varying harvest age, affecting stem and leaf proportions) will be important to obtain significant interactions during decomposition when its components are mixed.     

Pasture production and tree growth in a young pine plantation fertilized with inorganic fertilizers and milk sewage in northwestern Spain

The use of organic waste materials such as milk sewage as an organic fertilizer could have the dual advantages of organic-waste disposal and reduced dependence on inorganic fertilizers. The effects of fertilization with (1) conventional mineral fertilization, (2) milk sewage sludge at 40 kg N ha⁻¹ target rate and (3) no fertilization on pasture production and tree growth were examined in an experiment consisting of two pasture mixtures under a one-year-old Pinus radiata plantation with a density of 2500 trees ha⁻¹. The two pasture mixtures were: (1) Dactylis glomerata L. var. saborto (25 kg ha⁻¹) + Trifolium repens L. group Ladino (4 kg ha⁻¹) + Trifolium pratense L. var. Marino (1 kg ha⁻¹); (2) Lolium perenne L. var. Tove (25 kg ha⁻¹) + Trifolium repens L. group Ladino (4 kg ha⁻¹) + Trifolium pratense L. var. Marino (1 kg ha⁻¹). The experiment began in the spring of 1995 using a randomized block design with three replicates in Castro Riberas de Lea (Lugo, Galicia, north-western Spain). Plot size was 12 × 8 m², with a 1 m buffer strip between plots. Two-year data showed that fertilization with either material had a positive effect on pasture production, with no significant difference between the two fertilization treatments. Tree growth in the milk sewage sludge plot was significantly higher than in the control plots. Inorganic fertilization increased pasture production, but affected tree growth negatively. The results show that milk sewage sludge could be used as a fertilizer in silvo-pastoral systems. This revised version was published online in June 2006 with corrections to the Cover Date.