Effect of Coriolus versicolor on physico-chemical properties of Eucalyptus globulus wood

Summary The purpose of this study was to determine the progressive changes in physical and chemical properties of Eucalyptus globulus wood under the action of a representative white rot fungus, Coriolus versicolor. Observations concerning the nature and relative effects on weight loss, hot water solubility, 1% sodium hydroxide solubility, Klason lignin, holocellulose, intrinsic viscosity and degree of polymerisation of holocellulose, pentosans, methoxyl value, neutral sugar composition and nitrobenzene oxidation products are discussed.The authors thank Dr. P. S. Rehill, the then Officer-in-Charge, Forest Pathology Branch, for valuable suggestions and providing facilities for decay experiments     

Viscoelastic properties of wood from Chinese-fir and poplar plantations

Elastic and strength properties(proportional-limit stress(σ prop ),Young's modulus(E),breaking stress(σ max )in static bending parallel to grain in a longitudinal direction),as well as stress relaxation in air-dried condition and water-saturated conditions at seven different constant temperatures and increasing and decreasing temperatures were investigated for wood from Chinese-fir and poplar plantations.The results show that hygrothermal conditions considerably affect these mechanical properties.The higher the moisture content(MC)or temperature,the lower the strength of wood.Further investigation of the effects of constant temperature on stress relaxation indicates that high temperature specimens have low relaxation moduli and high fluidity.In the case of increasing temperature the range of the modulus of relaxation is larger than in the case of a reduction in temperature,while the residual moduli do not show large differences.This is because the modulus at high temperatures decreases more than that at low temperatures.The fluidity of specimens in a state of water desorption increases slowly at the beginning,increases quickly until the MC reaches an equilibrium moisture content(EMC)and then becomes stable,which is quite different from that in a water-saturated state.Fluidity in a desorption state is much higher than in a water-saturated state.This is probably due to the fact that the former is in an unstable state which can be interpreted as a state with internal strain and has therefore a greater potential to release strain.     

外生菌根菌对巨桉人工林土壤理化性质的影响

该文调查了四川乐山沙湾、眉山丹棱巨桉人工林下外生菌根菌土,测定了土壤养分情况。结果表明：两地所采集的菌根土的理化指标与对照相比有明显变化,样地Ⅰ菌根土pH值显著高于对照土,有机质含量与对照相比并不显著,样地ⅡpH值显著低于对照,而有机质含量明显高于对照;两样地菌根土的全N、水解N、全P和有效P含量均显著高于对照;大孢硬皮马勃的菌根土全K含量与对照相比并不显著,彩色豆马勃和马勃状硬皮马勃的菌根土全K含量均显著低于对照（P〈0.05）;样地Ⅰ菌根土速效K含量与对照差异不显著,样地Ⅱ菌根土速效K含量显著低于对照。由此可见,巨桉外生菌根真菌对提高巨桉人工林的土壤肥力,维护人工林地力具有一定作用。     

Establishment success of conservation tree plantations in relation to silvicultural practices in Indiana,USA

In the Central Hardwood Forest region of the United States, the variable and somewhat unpredictable establishment success of hardwood tree plantations has traditionally been attributed to competing vegetation and damage due to animal browse. We examined operational plantation establishment success (1–5 years following planting) as it relates to use of particular silvicultural practices. Silvicultural histories were obtained for 87 randomly selected plantations throughout Indiana and field data were collected from each to determine tree survival, tree vigor, and abundance of surrounding vegetation. Survival was highest at sites that were treated with herbicide prior to planting and that had been mechanically planted (as opposed to hand planted). The percentage of trees with evidence of dieback was highest on sites at which browse protection measures had been used, likely reflecting a combination of damage due to inherently high white-tailed deer (Odocoileus virginianus Zimmermann) populations at such sites and ineffectiveness of current browse protection measures. Sites planted by a professional forester and those with herbicide applied subsequent to planting had a higher percentage of trees deemed free-to-grow. Subsequent herbicide application did not reduce cover or height of competing vegetation; however, when used in conjunction with mechanical site preparation techniques, overall cover and height of herbaceous vegetation was reduced.     

Influence of site in the wood quality of Eucalyptus in plantations in Brazil

Genetic materials interact with the environment in specific ways, therefore their responses in wood need to be better understood. The present study sought to evaluate the influence of different climatic conditions in Minas Gerais, Brazil on Eucalyptus grandis × Eucalyptus urophylla wood. Two six-year-old clones were cultivated in Belo Oriente, Ferros, Santa Bárbara, Itabira and Peçanha. Five trees from each clone were sampled from the base to top direction. Wood density, heartwood/sapwood ratio, vessels, fibres, and extractive and lignin contents were determined, as well as their correlation with environmental variables. Vessel diameters, heartwood/sapwood ratio, and extractive and lignin contents all increased due to higher water availability in Santa Bárbara and Itabira. In both genetic materials, the variables linked to growth and wood quality were related to environmental factors.     

Calcium accumulation in the wood of short-rotation cottonwood species: effects on pulp properties

We have found that kraft pulp handsheets, made from a number of hybrid poplar (Populus trichocarpa × Populus deltoides) clones, contain unusual surface deformations caused by vessel element mineral blockages. The blockages were composed mainly of calcium salt deposits that survived chemical pulping and beating processes. Our findings confirm that a natural process of accumulation of calcium salts occurs in certain poplar species. In this article, we describe the implications for the multi-use implementation of these poplars in short-rotation, intensive-culture plantations.     

Relationships between nursery practices and field performance for Eucalyptus plantations in Brazil

The 3.5 million ha of Eucalyptus plantations in Brazil support many domestic and industrial activities. In the pulpwood sector, forest productivity has increased from 12 to 40 m³ ha^–1 year^–1 through breeding and silviculturalpractices. Nurseries have fostered thisevolution with changes in container/substratetypes, propagation methods and specificinfrastructure for each plant growth phase.Eucalyptus plants are mainly produced bycuttings, using rigid tube containers filledwith vermiculite-organic compound substrates.Stock quality is based on morphologicalcharacteristics of the plants, andenvironmental conditions are highly significantfor plant performance. Performance is dependenton physiological short-term effects related tosurvival and long-term effects of genotype/rootmorphology related to tree development. Currentsilvicultural trends are reducing establishmentcosts but increasing the risk of using lowquality plants. The development of fieldperformance models and nursery physiologicaltests is recommended for Eucalyptusplantations in Brazil. Improved experimentaldesigns are needed to capture the interactionbetween plant quality and field performance.     

The impact of carbon trade on the management of short-rotation forest plantations

We extended the Hartman model to examine the optimal rotation, taking into consideration the economic benefits of wood and the dynamics of three carbon pools (aboveground biomass, dead organic matter, and harvested forest products). Chinese fir (Cunninghamia lanceolata) stands in Southern China were taken for a numerical example to analyze the effects of carbon price on the optimal management of short-rotation plantations. The results show that, with the current price of carbon, introducing the effects of harvesting on different carbon pools into the decision model would increase the optimal rotation age on poor (SI = 10) and medium (SI = 17) sites by one year, while it does not have any impact on the optimal rotation for good sites (SI = 21). Irrespective of site condition, the optimal rotation age is not sensitive to carbon price and interest rate. An increase in interest rate by 1% would reduce the optimal rotation age by one year. In conclusion, forest carbon trade could effectively enhance land owners' income from short-rotation forest plantations. However, it does not lead to any significant increase in forest carbon sink.     

短轮伐期菇木林营造技术研究

银荆、南酸枣、秃瓣杜英、马褂木等8个袋栽香菇试验表明，麻栎、南酸枣每千克干料产鲜香菇为944g和882g，比对照高45．23％和35．69％；桤木、秃辨杜英、银荆、锥栗、马褂木、枫香等产菇量比对照高7．18％～20．92％。造林试验表明，4a生的银荆树高8．93m，胸径8．20cm，生物产量高达189891kg／hm^2；5a生南酸枣、秃辨杜英、马褂木、枫香、锥栗、麻栎生物产量达83790～150228kg／hm^2。研究认为银荆、南酸枣、秃辨社英、马褂木等树种具有早期丰产的特性，采用密植造林4～5a可获得较高的生物产量与经济效益。     

Rapid assessment of wood chemical properties and pulp yield of Eucalyptus camaldulensis in Thailand tree plantations by near infrared spectroscopy for improving wood selection for high quality pulp

Near-infrared (NIR) spectroscopy has been demonstrated as a means for rapid nondestructive determination of the chemical composition and final pulp yield of Eucalyptus camaldulensis in Thailand tree plantations. Multiple linear regression (MLR) analysis and partial least squares (PLS) analysis were introduced to develop statistical models in terms of calibration equations for total pulp yield, screened pulp yield, and contents of -cellulose, pentosans, and lignin in wood. In MLR analysis, a reasonably good calibration equation was found only for pentosans (standard error of prediction (SEP): 0.98%). The PLS analysis improved the accuracy of prediction for every criterion variable, especially for pentosans (SEP: 0.91%) and lignin (SEP: 0.52%). Also, in the case of screened pulp yield, we were able to use such a statistical result as an indicator of the characteristics of the pulp and paper. Thus, NIR spectroscopy could be satisfactorily used as an effective assessment technique for Eucalyptus camaldulensis plantation trees.     

Methods for the determination of wood properties,Kraft pulp yield and wood fibre dimensions on small wood samples.

A trial set-up with methods for sampling, treatment and analysis of small wood chips are presented in this paper, to determine important wood and fibre properties, like basic density, dry density, volume swelling of wood, Kraft pulp yield, fibre length, fibre coarseness, fibre width, lumen width and fibre wall thickness. The required time for one sample is about 1.5 man-hour, but this requires relatively larger series and trained personnel. Acceptable measurement accuracy is achieved when the volume of the wood sample is at least 1.5 ml, except that of wood volume swelling. To gain acceptable measurement accuracy for volume swelling, the wood volume should be increased to at least 3 ml, and preferably more than 5–6 ml per sample. The level of pulp yield and wood density do not show a significant effect on the measurement accuracy for fibre cross-section dimensions. Fibre coarseness, on the other hand, has a significant influence on these accuracies. A double measurement of fibre coarseness will improve the accuracy to an acceptable level. The method presented here may, together with information about trees and growth locations, form the basis for greater insight into the mechanisms involved in development of wood and fibre properties in trees, which in turn may provide better control and utilisation of wood for pulp and paper production.Abbreviations CWD cell wall density in dry wood=1500 kg/m³ - Ww dry weight of wood (kg) - Vmax green (wet) volume of wood (m³) - Vmin dry volume of wood (m³) - BD basic wood density (kg/m³) - DD dry wood density (kg/m³) - VS maximum volume swelling of wood (%) - Wp dry weight of pulp (kg) - PY pulp yield (%) - C fibre coarseness, the average weight of a unit length of fibre (g/m) - CL average chip length (mm) - CWT average cell wall thickness (m) - FW average fibre width (m) - l average native fibre length in solid wood - L chip length - lc average fibre length in wood chip (mm) - Lc length-weighted fibre length in wood chip (mm) - lw native average fibre length in wood (mm) - Lw native length-weighted fibre length in wood (mm) - LW average lumen width (m) - llw average native fibre length, length weighted, in wood - X average fibre length in chip - Xlw average fibre length, length weighted, in chip     

Non-isothermal autohydrolysis of Eucalyptus wood

Non-isothermal autohydrolysis treatments of Eucalyptus globulus wood were carried out in batch reactors in order to assess the kinetics of hemicellulose degradation, as well as the effects caused on cellulose and lignin. Experiments were carried out at a liquor to wood ratio of 8 g/g, and two heating profiles were explored. The maximum temperature considered was 224 °C, and the longest reaction time was 0.94 h. The experimental variables considered were solid residue yield, solid residue composition and composition of liquors. Up to 90.4% of the initial xylan was removed in treatments, which also caused some delignification (up to 13.8% of the initial lignin was removed), whereas cellulose was almost quantitatively retained in solid phase. The conversion of xylan into xylooligomers, with further hydrolysis to xylose and decomposition of this sugar into furfural was assessed by means of a kinetic model based on sequential, first order reactions involving kinetic coefficients with Arrhenius-type dependence on temperature. Received 23 November 1999     

Effects of site on fibre, kraft pulp and handsheet properties of Eucalyptus globulus

? Eight-year old trees from two Eucalyptus globulus Labill. clones planted across three different sites in Tasmania, Australia, were sampled for wood and kraft pulp/handsheet properties.

? Site had a significant effect on all measured properties. Compared with the poor site (Parkham) the wood from the good site (West Ridgley) had on average 11 % lower wood density. The poor site had also greater microfibril angles, shorter fibres at lower pulp yields.

? The handsheets produced with pulp from the poor site resulted in comparatively higher bulkiness, lower burst, lower tear and tensile indices, lower zero span tensile strength, but higher opacity, higher light scattering and higher surface roughness. Significant height effects were found with all wood properties, and also with tear index, zero span tensile strength and opacity.

? Discriminant analysis showed that for 76 out of 100 handsheets the raw material source, i.e. growth site, could be predicted correctly using a set of handsheet properties with tear index and bulk index being most prominent.

? This is unique evidence that site conditions are strongly reflected in handsheet properties produced from Eucalyptus pulp.

     

我国桉树人工林施肥研究进展

科学施肥是实现桉树人工林速生丰产的一个重要措施。本文从桉树人工林施肥研究的历史、桉树种植区的土壤肥力、施肥效应、营养诊断和平衡施肥等方面综述了桉树人工林施肥的研究进展,指出了目前研究中存在的问题和今后的研究方向,为我国桉树速生丰产林的可持续经营提供科学依据。     

湖南省邓恩桉与柳桉高产纤维材引种培育研究进展

中国大多数桉树资源主要集中在较为温暖的沿海地区.目前在湖南和江西等华南和中南省份较为冷凉的内陆地区,通过选择一些合适的耐寒桉树品种,种植了一些规模不大的桉树人工示范林,这些示范林显示出了较好的适应性与丰产性.这些较为冷凉的内陆地区有着立地条件较为优越的适合人工林发展的广大林地.对于较冷地区,尤其是湖南省来说,通过分析所...     

Mycosphaerella species occurring on Eucalyptus globulus and Eucalyptus nitens plantations of Tasmania,Australia

The genus Mycosphaerella Johanson contains many pathogens capable of causing a severe impact on the growth of susceptible eucalypt species. The lack of knowledge about which species are present in Tasmania and their potential risk to the plantation industry prompted this study into the Mycosphaerella species occurring on Eucalyptus globulus and Eucalyptus nitens plantations in Tasmania. A total of 36 plantation and five road verge sites of E. globulus and E. nitens were sampled. Five Mycosphaerella species and three species from associated anamorph genera were isolated and identified in Tasmania; Mycosphaerella nubilosa, Mycosphaerella cryptica, Mycosphaerella tasmaniensis, Mycosphaerella grandis, Mycosphaerella vespa, Coniothyrium ovatum, Sonderhenia eucalypticola and Sonderhenia eucalyptorum. The most frequently isolated species with the highest incidence and severity of infection were M. cryptica and M. nubilosa. These two species appear to have the greatest potential to damage juvenile eucalypt plantations in Tasmania. A link between Mycosphaerella vespa and Coniothyrium ovatum is described for the first time.     

广东桉树林土壤物理性质及其影响因子分析

研究了广东省桉树人工林土壤体积质量、孔隙度、水分含量现状、各指标之间的相关关系以及海拔、坡度和土壤有机质对上述物理性质的影响。结果表明:广东省桉树人工林土壤A层总孔隙度、毛管持水量、全容水量、吸湿水含量显著高于B层,A层体积质量显著小于B层;不同区域土壤A层体积质量、总孔隙度、非毛管孔隙度和全容水量存在显著差异;除了非毛管孔隙度仅与全容水量(A层)、毛管持水量和毛管孔隙度(B层)显著相关外,土壤其他物理性质之间均呈显著或极显著相关性;土壤体积质量与毛管孔隙度、毛管持水量、全容水量的最佳回归方程分别为对数方程、一元二次方程和指数方程;海拔和坡度显著影响表层土壤的物理性质,对B层影响不显著;有机质对土壤A、B层物理性质均有显著影响。     

The effect of wide initial spacing on wood properties in plantation grown Eucalyptus pilularis

Eucalyptus pilularis planted at three initial stocking densities of 833, 1111 and 1,667 stems ha^?1 grown at either square or rectangular spacing was assessed for the effects of stocking and rectangularity on wood properties. Sample trees from each stocking and rectangularity combination were harvested at age 7 years and assessed for the commercially important wood properties of bow, as an indication of growth strain, shrinkage and basic density. Crown length ratio was used as an indicator of stand vigour and clear wood availability. Furthermore comment is made on the financial ramifications of wide inter-row spacing. Stocking and rectangularity significantly influenced bow but not shrinkage or basic density. Reducing within-row spacing to 2 m with a larger between-row-space of 6 m had minimal affect on wood properties. Reducing the number of rows, whilst still retaining a commercial stocking, reduces the establishment costs and increases the ease of mechanical harvesting without adversely affecting log value.