Yield and quality response of drip irrigated broccoli (Brassica oleracea L. var. italica) under different irrigation regimes, nitrogen applications and cultivation periods

The experiment aimed at evaluating the yield and quality response of broccoli (Brassica oleracea L. var. italica) to applied irrigation water and nitrogen by drip irrigation method during the spring and autumn cultivation periods of 2007. Irrigation water was applied based on a ratio of Class A pan evaporation (k_cp = 0.50, 0.75, 1.00 and 1.25) with 7 days interval. Also, the effect of four nitrogen levels (0 kg ha⁻¹, 150 kg ha⁻¹, 200 kg ha⁻¹ and 250 kg ha⁻¹) was compared with each treatment. The seasonal evapotranspiration in the treatments varied from 233 mm to 328 mm during the spring period and from 276 mm to 344 mm during the autumn period. The highest broccoli yield was obtained in the spring period as 11.02 t ha⁻¹ and in the autumn period as 4.55 t ha⁻¹. In general, there were statistical differences along nitrogen does with respect to yield and yield components while there were no statistically significant differences in the yield and yield components among irrigation regimes. Both yield and yield parameters in the spring period were found to be higher than that of the autumn period due to the low temperature and high rainy days in autumn. Irrigation water use efficiency (IWUE) ranged from 3.78 kg m⁻³ to 14.61 kg m⁻³ during the spring period and from 1.89 kg m⁻³ to 5.93 kg m⁻³ during the autumn period. On the other hand, nitrogen use efficiency (NUE) changed as 37.32-73.13% and 13.08-22.46% for spring and autumn season, respectively.     

A modified checkbook irrigation method based on GIS-coupled model for regional irrigation scheduling

In this study, a regional irrigation schedule optimization method was proposed and applied in Fengqiu County in the North China Plain, which often suffers serious soil water drainage and nitrogen (N) leaching problems caused by excessive irrigation. The irrigation scheduling method was established by integrating the ‘checkbook irrigation method’ into a GIS-coupled soil water and nitrogen management model (WNMM) as an extension. The soil water and crop information required by the checkbook method, and previously collected from field observations, was estimated by the WNMM. By replacing manually observed data with simulated data from WNMM, the application range of the checkbook method could be extended from field scale to regional scale. The WNMM and the checkbook irrigation method were both validated by field experiments in the study region. The irrigation experiment in fluvo–aquic soil showed that the checkbook method had excellent performance; soil water drainage and N leaching were reduced by 83.1 and 85.6%, respectively, when compared with local farmers’ flood irrigation. Using the validated WNMM, the performance of checkbook irrigation in an entire winter wheat and summer maize rotation was also validated: the average soil water drainage and N leaching in four types of soils decreased from 331 to 75 mm year⁻¹ and 47.7 to 9.3 kg ha⁻¹ year⁻¹, respectively; and average irrigation water use efficiency increased from 26.5 to 57.2 kg ha⁻¹ mm⁻¹. The regional irrigation schedule optimization method based on WNMM was applied in Fengqiu County. The results showed a good effect on saving irrigation water, decreasing soil water drainage and then saving agricultural inputs. In a typical meteorological year, it could save >110 mm of irrigation water on average, translating to >7.26 × 10⁷ m³ of agricultural water saved each year within the county. Annual soil water drainage was reduced to <143 mm and N leaching to <27 kg ha⁻¹ in most soils, all of which were significantly lower than local farmers’ flood irrigation. In the mean time, crop yield also had an average increase of 2,890 kg ha⁻¹ when checkbook irrigation was applied.     

Integrated management of irrigation water and fertilizers for wheat crop using field experiments and simulation modeling

The reported study aimed at developing an integrated management strategy for irrigation water and fertilizers in case of wheat crop in a sub-tropical sub-humid region. Field experiments were conducted on wheat crop (cultivar Sonalika) during the years 2002–2003, 2003–2004 and 2004–2005. Each experiment included four fertilizer treatments and three irrigation treatments during the wheat growth period. During the experiment, the irrigation treatments considered were I₁ = 10% maximum allowable depletion (MAD) of available soil water (ASW); I₂ = 40% MAD of ASW; I₃ = 60% MAD of ASW. The fertilizer treatments considered in the experiments were F₁ = control treatment with N:P₂O₅:K₂O as 0:0:0 kg ha⁻¹, F₂ = fertilizer application of N:P₂O₅:K₂O as 80:40:40 kg ha⁻¹; F₃ = fertilizer application of N:P₂O₅:K₂O as 120:60:60 kg ha⁻¹ and F₄ = fertilizer application of N:P₂O₅:K₂O as 160:80:80 kg ha⁻¹. In this study CERES-wheat crop growth model of the DSSAT v4.0 was used to simulate the growth, development and yield of wheat crop using soil, daily weather and management inputs, to aid farmers and decision makers in developing strategies for effective management of inputs. The results of the investigation revealed that magnitudes of grain yield, straw yield and maximum LAI of wheat crop were higher in low volume high frequency irrigation (I₁) than the high volume low frequency irrigation (I₃). The grain yield, straw yield and maximum LAI increased with increase in fertilization rate for the wheat crop. The results also revealed that increase in level of fertilization increased water use efficiency (WUE) considerably. However, WUE of the I₂ irrigation schedule was comparatively higher than the I₁ and I₃ irrigation schedules due to higher grain yield per unit use of water. Therefore, irrigation schedule with 40% maximum allowable depletion of available soil water (I₂) could safely be maintained during the non-critical stages to save water without sacrificing the crop yield. Increase in level of fertilization increases the WUE but it will cause environmental problem beyond certain limit. The calibrated CERES-wheat model could predict the grain yield, straw yield and maximum LAI of wheat crop with considerable accuracy and therefore can be recommended for decision-making in similar regions.     

Effect of small irrigation amounts on the yield of wheat

Yields of dryland crops are governed by the moisture in the soil profile at seeding and by rainfall during the growing season. Occasionally limited amounts of water may also be available for irrigation. Field experiments were conducted over a period of 4 years on loamy sand and 3 years on sandy loam to study the effects of pre-seeding, post-seeding and split application of limited amounts of water on root growth, water use, dry matter accumulation and grain yield of wheat. This article reports the treatment effects on dry matter accumulation and grain yield.Early season water stress decreased the rate of dry matter accumulation. Grain yield responded significantly to irrigation 30 days after seeding irrespective of the amount of water, year and soil type. Yield with post-seeding irrigation averaged 3518 kg ha^?1 against 2317 kg ha^?1 for unirrigated control in loamy sand and 4440 kg ha^?1 against 3391 kg ha^?1 in sandy loam. The increase in yield was manifested by a significant increase in the number of effective tillers per m row length, number of grains per ear and thousand grain weight.     

Dynamics of plant and animal production of a subterranean clover pasture grazed by sheep: Part 1—Field measurements for model calibration

A grazing system with Merino sheep and subterranean clover pasture was studied in a 550 mm rainfall, mediterranean climate in Western Australia.Changes over twelve months in seed, the quantities of green and dry herbage, soil moisture, animal intake and liveweight, wool growth and body composition were measured. Six paddocks, representing two soil types, were grazed continuously at 8·75 sheep per hectare. The system was also simulated and the actual results were compared with those from the simulation model.From a seed pool in March of 300 kg ha^?1, 80% of which was soft and non-dormant, 4000 clover seedlings per square metre became established; subsequent drought reduced this to 1450 plants per square metre. From measurements of soil moisture it was shown that this population survived at available moisture levels as low as 0·5 mm in the main root zone in gravelly sandy loam. Pasture growth rate reached a spring peak of 102 kg ha^?1 day^?1 and total growth (estimated from pasture grazed for 26 weeks) was 6700 kg ha^?1 for 500 mm of rainfall between germination and maximum biomass. At maturity, burr and seed made up 57% of the plant residues on offer, with a seed pool of 1160 kg ha^?1. During the summer this biomass decreased at 5 kg ha^?1 day^?1 without grazing and 19 kg ha^?1 day^?1 under grazing.The liveweight losses and gains of the sheep were atypical, no liveweight gain until 1200 kg ha^?1 of gree herbage was available—about treble the expected amount. Measurements of food intake indicate a gross inefficiency in energy utilisation during the winter and a low intake of energy in the spring.Total green and dry plant residues showed general agreement between actual and simulated results for most of the growing season. However, the field data highlighted error in the pasture sub-model which were corrected and are reported elsewhere.     

Yield and water-production functions of two durum wheat cultivars grown under different irrigation and nitrogen regimes

Wheat (Triticum durum L.) yields in the semi-arid regions are limited by inadequate water supply late in the cropping season. Planning suitable irrigation strategy and nitrogen fertilization with the appropriate crop phenology will produce optimum grain yields. A 3-year experiment was conducted on deep, fairly drained clay soil, at Tal Amara Research Station in the central Bekaa Valley of Lebanon to investigate the response of durum wheat to supplemental irrigation (IRR) and nitrogen rate (NR). Three water supply levels (rainfed and two treatments irrigated at half and full soil water deficit) were coupled with three N fertilization rates (100, 150 and 200 kg N ha⁻¹) and two cultivars (Waha and Haurani) under the same cropping practices (sowing date, seeding rate, row space and seeding depth). Averaged across N treatments and years, rainfed treatment yielded 3.49 Mg ha⁻¹ and it was 25% and 28% less than half and full irrigation treatments, respectively, for Waha, while for Haurani the rainfed treatment yielded 3.21 Mg ha⁻¹, and it was 18% and 22% less than half and full irrigation, respectively. On the other hand, N fertilization of 150 and 200 kg N ha⁻¹ increased grain yield in Waha by 12% and 16%, respectively, in comparison with N fertilization of 100 kg N ha⁻¹, while for cultivar Haurani the increases were 24% and 38%, respectively. Regardless of cultivar, results showed that supplemental irrigation significantly increased grain number per square meter and grain weight with respect to the rainfed treatment, while nitrogen fertilization was observed to have significant effects only on grain number per square meter. Moreover, results showed that grain yield for cultivar Haurani was less affected by supplemental irrigation and more affected by nitrogen fertilization than cultivar Waha in all years. However, cultivar effects were of lower magnitude compared with those of irrigation and nitrogen. We conclude that optimum yield was produced for both cultivars at 50% of soil water deficit as supplemental irrigation and N rate of 150 kg N ha⁻¹. However, Harvest index (HI) and water use efficiency (WUE) in both cultivars were not significantly affected neither by supplemental irrigation nor by nitrogen rate. Evapotranspiration (ET) of rainfed wheat ranged from 300 to 400 mm, while irrigated wheat had seasonal ET ranging from 450 to 650 mm. On the other hand, irrigation treatments significantly affected ET after normalizing for vapor pressure deficit (ET/VPD) during the growing season. Supplemental irrigation at 50% and 100% of soil water deficit had approximately 26 and 52 mm mbar⁻¹ more ET/VPD, respectively, than those grown under rainfed conditions.     

Irrigation, tillage and mulching effects on soybean yield and water productivity in relation to soil texture

Depleting groundwater resources in Indian Punjab call for diversifying from rice to crops with low evapo-transpiration needs and adopting water-saving technologies. Soybean offers a diversification option in coarse- to medium-textured soils. However, its productivity in these soils is constrained by high soil mechanical resistance and high soil temperature during early part of the growing season. These constraints can be alleviated through irrigation, deep tillage and straw mulching. This 3-years field study examines the individual and combined effects of irrigation, deep tillage, and straw mulching regimes on soybean yield and water productivity (WP) in relation to soil texture. Combinations of two irrigation regimes viz., full irrigation (I_f), and partial irrigation (I_p) in the main plot; two tillage regimes viz., conventional-till (CT)-soil stirring to 0.10 m depth, and deep tillage (DT)-chiseling down to 0.35 m depth followed by CT in the subplot; and two mulch rates viz., 0 (M₀) and 6 t ha⁻¹ (M) in the sub-subplot on two soils differing in available water capacity were evaluated.Seed yield was greater in the sandy loam than in the loamy sand reflecting the effects of available water capacity. Irrigation effects were greater on loamy sand (40%) than on sandy loam (5%) soil. Deep tillage benefits were also more on loamy sand (14%) compared to sandy loam (5%) soil. Yield gains with mulching were comparable on the two soils (19%). An evaluation of interaction effects showed that mulching response was slightly more in I_p (20%) than in I_f regimes (17%) in the sandy loam; while in the loamy sand, mulching gains were comparable (18-19%) in both irrigation regimes. Benefits of deep tillage in the loamy sand soil were more in I_p (20%) than in I_f regimes (17%). Deep tillage and straw mulching enhanced WP (ratio of seed yield/water use) from 1.39 to 1.97 kg ha⁻¹ mm⁻¹ in I_p regime, and from 1.87 to 2.33 kg ha⁻¹ mm⁻¹ in I_f regime in the loamy sand soil. These effects on WP were less in the sandy loam soil with greater available water capacity. Yield and WP gains are ascribed to deeper and denser rooting due to moderation of soil temperature and water conservation with straw mulching and tillage-induced reduction in soil mechanical resistance. Root mass in CTM₀, CTM, DTM₀ and DTM was 2.79, 5.88, 5.34 and 5.58 mg cm⁻² at pod-filling in the loamy sand soil. Comparable yield responses to deep tillage or mulching in the loamy sand soil suggest that either of the options, depending on their cost and availability considerations, can be employed for improving soybean yield and water productivity.     

Forage quality, water use and nitrogen utilization efficiencies of pearl millet (Pennisetum americanum L.) grown under different soil moisture and nitrogen levels

The increasing scarcity of water for irrigation is becoming the most important problem for producing forage in all arid and semi-arid regions. Pearl millet is a key crop in these regions which needs relatively less water than other crops. In this research, a field study was conducted to identify the best combination of irrigation and nitrogen (N) management to achieve acceptable pearl millet forage both in quantity and quality aspects. Pearl millet was subjected to four irrigation treatments with interaction of N fertilizer (0, 75, 150 and 225 kg ha⁻¹). The irrigation treatments were 40%, 60%, 80% and 100% of total available soil water (I₄₀, I₆₀, I₈₀ and I₁₀₀, respectively). The results showed that increasing moisture stress (from I₄₀ to I₁₀₀) resulted in progressively less total dry matter (TDM), leaf area index (LAI), and nitrogen utilization efficiency (NUzE), while water use efficiency (WUE) and the percentage of crude protein (CP%) increased. The highest TDM and LAI were found to be 21.45 t ha⁻¹ and 8.65, in I₄₀ treatment, respectively. TDM, WUE, CP% and profit responses to N rates were positive. The maximum WUE of 4.19 kg DM/m³ was achieved at I₁₀₀ with 150 kg N ha⁻¹. The results of this research indicate that the maximum profit of forage production was obtained in plots which were fully irrigated (I₄₀) and received 225 kg N ha⁻¹. However, in the situation which water is often limited and not available, application of 150 kg N ha⁻¹ can produce high forage quality and guaranty acceptable benefits for farmers.     

The effects of irrigation methods with effluent and irrigation scheduling on water use efficiency and corn yields in an arid region

A great challenge for the agricultural sector is to produce more food from less water, particularly in arid and semi-arid regions which suffer from water scarcity. A study was conducted to evaluate the effect of three irrigation methods, using effluent versus fresh water, on water savings, yields and irrigation water use efficiency (IWUE). The irrigation scheduling was based on soil moisture and rooting depth monitoring. The experimental design was a split plot with three main treatments, namely subsurface drip (SSD), surface drip (SD) and furrow irrigation (FI) and two sub-treatments effluent and fresh water, which were applied with three replications. The experiment was conducted at the Marvdasht city (Southern Iran) wastewater treatment plant during 2005 and 2006. The experimental results indicated that the average water applied in the irrigation treatments with monitoring was much less than that using the conventional irrigation method (using furrows but based on a constant irrigation interval, without moisture monitoring). The maximum water saving was obtained using SSD with 5907 m³ ha⁻¹ water applied, and the minimum water saving was obtained using FI with 6822 m³ ha⁻¹. The predicted irrigation water requirements using the Penman-Monteith equation (considering 85% irrigation efficiency for the FI method) was 10,743 m³ ha⁻¹. The pressure irrigation systems (SSD and SD) led to a greater yield compared to the surface method (FI). The highest yield (12.11 × 10³ kg ha⁻¹) was obtained with SSD and the lowest was obtained with the FI method (9.75 × 10³ kg ha⁻¹). The irrigation methods indicated a highly significant difference in irrigation water use efficiency. The maximum IWUE was obtained with the SSD (2.12 kg m⁻³) and the minimum was obtained with the FI method (1.43 kg m⁻³). Irrigation with effluent led to a greater IWUE compared to fresh water, but the difference was not statistically significant.     

Irrigation and tillage effects on root development,water use and yield of wheat on coarse textured soils

Summary Rapid drying of surface layers of coarse-textured soils early in the growth season increases soil strength and restricts root growth. This constraint on root growth may be countered by deep tillage and/or early irrigation. We investigated tillage and irrigation effects on root growth, water use, dry matter and grain yield of wheat on loamy sand and sandy loam soils for three years. Treatments included all combinations of two tillage systems i) conventional tillage (CT) — stirring the soil to 10 cm depth, ii) deep tillage (DT) — subsoiling with a single-tine chisel down to 35–40 cm, 40 cm apart followed by CT; and four irrigation regimes, i) I₀ — no post-seeding irrigation, ii) I₁ — 50 mm irrigation 30 days after seeding (DAS), iii) I₂ — 50 mm irrigation 30 DAS and subsequent irrigations of 75 mm each when net evaporation from USWB class A open pan (PAN-E) since previous irrigation accumulated to 82 mm, and iv) I₃ — same as in I² but irrigation applied when PAN-E accumulated to 62 mm. The crop of wheat (Triticum aestivum L. HD 2329) was fertilized with 20kg P, 10kg K and 5kg Zn ha^–1 at seeding. The rate of nitrogen fertilization was 60 kg ha^–1 in the unirrigated and 120 kg ha^–1 in the irrigated treatments. Tillage decreased soil strength and so did the early post-seeding irrigation. Both deep tillage and early irrigation shortened the time needed for the root system to reach a specified depth. Subsequent wetting through rain/irrigation reduced the rate of root penetration down the profile and also negated deep tillage effects on rooting depth. However, tillage/irrigation increased root length density in the rooted profile even in a wet year. Better rooting resulted in greater profile water depletion, more favourable plant water status and higher dry matter and grain yields. In a dry year, the wheat in the DT plots used 46 mm more water, remained 3.3 °C cooler at grain-fill and yielded 68% more grain than in CT when unirrigated and grown in the loamy sand. Early irrigation also increased profile water depletion, more so in CT than DT. Averaged over three years, grain yield in DT was 12 and 9% higher than in CT on loamy sand and sandy loam, respectively. Benefits of DT decreased with increase in rainfall and irrigation. Irrigation significantly increased grain yield on both soils, but the response was greatly influenced by soil type, tillage system and year. The study shows that soil related constraints on root growth may be alleviated through deep tillage and/or early irrigation.     

Effects of irrigation strategies and soils on field grown potatoes: Yield and water productivity

Yield and water productivity of potatoes grown in 4.32 m² lysimeters were measured in coarse sand, loamy sand, and sandy loam and imposed to full (FI), deficit (DI), and partial root-zone drying (PRD) irrigation strategies. PRD and DI as water-saving irrigation treatments received 65% of FI after tuber bulking and lasted for 6 weeks until final harvest. Analysis across the soil textures showed that fresh yields were not significant between the irrigation treatments. However, the same analysis across the irrigation treatments revealed that the effect of soil texture was significant on the fresh yield and loamy sand produced significantly higher fresh yield than the other two soils, probably because of higher leaf area index, higher photosynthesis rates, and “stay-green” effect late in the growing season. More analysis showed that there was a significant interaction between the irrigation treatments and soil textures that the highest fresh yield was obtained under FI in loamy sand. Furthermore, analysis across the soil textures showed that water productivities, WP (kg ha⁻¹ fresh tuber yield mm⁻¹ ET) were not significantly different between the irrigation treatments. However, across the irrigation treatments, the soil textures were significantly different. This showed that the interaction between irrigation treatments and soil textures was significant that the highest significant WP was obtained under DI in sandy loam. While PRD and DI treatments increased WP by, respectively, 11 and 5% in coarse sand and 28 and 36% in sandy loam relative to FI, they decreased WP in loamy sand by 15 and 13%. The reduced WP in loamy sand was due to nearly 28% fresh tuber yield loss in PRD and DI relative to FI even though ET was reduced by 9 and 11% in these irrigation treatments. This study showed that different soils will affect water-saving irrigation strategies that are worth knowing for suitable agricultural water management. So, under non-limited water resources conditions, loamy sand produces the highest yield under full irrigation but water-saving irrigations (PRD and DI) are not recommended due to considerable loss (28%) in yield. However, under restricted water resources, it is recommended to apply water-saving irrigations in sandy loam and coarse sand to achieve the highest water productivity.     

Irrigation planning in cotton through simulation modeling

Experiments were undertaken at CCS Haryana Agricultural University Farm, Sirsa (India) to estimate the optimum irrigation schedule for cotton resulting in minimum percolation losses. The sprinkler line source technique was adopted for creating various irrigation regimes at different crop growth stages. The SWASALT (Simulation of Water And SALT) model after calibration and validation provided water balance components. The wa-ter management response indicators (WMRI's) such as transpiration efficiency E_t/(Irr + P), relative transpiration E_t/E_tp, evapotranspiration efficiency ET/(Irr + P), soil moisture storage change ΔW/W_int (deficit/excess) and percolation loss Perc/(Irr. + P) were evaluated using water balance components as estimated by the simulation study. Under limited water supply conditions, the optimum irrigation depth was found to be 57 mm at crop growth stages with pre-sowing and 1^st irrigation of 120 mm and 80 mm respectively for sandy clay loam underlain by sandy loam soil (Type I). The corresponding values of relative transpiration, transpiration efficiency and evapotranspiration efficiency were 0.65, 0.65 and 0.89 respectively. The crop yield varied linearly with increasing irrigation depth which was evident from increase in relative transpiration with increasing depth of water application. However, increased depth of irrigation resulted in less moisture utilisation from soil storage (20% depletion at 40 mm depth and 4.4% moisture built up at 100 mm depth). The extended simulation study for sandy soil underlain by loamy sand (Type II) indicated that two pre-sowing irrigations each 40 mm and subsequent irrigations of 40 mm at an interval of 20 days depending upon rainfall were optimum. This irrigation scenario resulted in zero percolation loss accompanied by 74% relative transpiration and 14 per cent soil moisture depletion. Received: 20 November 1995     

Tomato nitrogen accumulation and fertilizer use efficiency on a sandy soil, as affected by nitrogen rate and irrigation scheduling

Tomato production systems in Florida are typically intensively managed with high inputs of fertilizer and irrigation and on sandy soils with low inherent water and nutrient retention capacities; potential nutrient leaching losses undermine the sustainability of such systems. The objectives of this 3-year field study were to evaluate the interaction between N-fertilizer rates and irrigation scheduling on crop N and P accumulation, N-fertilizer use efficiency (NUE) and NO₃-N leaching of tomato cultivated in a plastic mulched/drip irrigated production system in sandy soils. Experimental treatments were a factorial combination of three irrigation scheduling regimes and three N-rates (176, 220, and 330 kg ha⁻¹). Irrigation treatments included were: (1) surface drip irrigation (SUR) both the irrigation and fertigation line placed underneath the plastic mulch; (2) subsurface drip irrigation (SDI) where the irrigation drip was placed 0.15 m below the fertigation line which was located on top of the bed; and (3) TIME (conventional control) with the irrigation and fertigation lines placed as in SUR and irrigation applied once a day. Except for the TIME treatment all irrigation treatments were soil moisture sensor (SMS)-based with irrigation occurring at 10% volumetric water content. Five irrigation windows were scheduled daily and events were bypassed if the soil water content exceeded the established threshold. The use of SMS-based irrigation systems significantly reduced irrigation water use, volume percolated, and nitrate leaching. Based on soil electrical conductivity (EC) readings, there was no interaction between irrigation and N-rate treatments on the movement of fertilizer solutes. Total plant N accumulation for SUR and SDI was 12-37% higher than TIME. Plant P accumulation was not affected by either irrigation or N-rate treatments. The nitrogen use efficiency for SUR and SDI was on the order of 37-45%, 56-61%, and 61-68% for 2005, 2006 and 2007, respectively and significantly higher than for the conventional control system (TIME). Moreover, at the intermediate N-rate SUR and SDI systems reduced NO₃-N leaching to 5 and 35 kg ha⁻¹, while at the highest N-rate corresponding values were 7 and 56 kg N ha⁻¹. Use of N application rates above 220 kg ha⁻¹ did not result in fruit and/or shoot biomass nor N accumulation benefits, but substantially increased NO₃-N leaching for the control treatment, as detected by EC monitoring and by the lysimeters. It is concluded that appropriate use of SDI and/or sensor-based irrigation systems can sustain high yields while reducing irrigation application as well as reducing NO₃-N leaching in low water holding capacity soils.     

秋灌定额对越冬期土壤水盐运移分布的影响

通过盐渍化冻融土壤秋灌试验,研究了不同秋灌定额下越冬期间土壤含水率、盐分的变化情况。结果表明,秋灌定额为150～200 mm时,春播期土壤含水率基本适宜。秋灌定额对土壤盐分的动态影响较大,秋灌能够起到冲洗压盐的作用。但是秋灌定额不宜过大,秋灌前不实施耕作措施更有利于储水保墒。     

Irrigation strategies to improve the water use efficiency of wheat-maize double cropping systems in North China Plain

Water is the most important limiting factor of wheat (Triticum aestivum L.) and maize (Zea mays L.) double cropping systems in the North China Plain (NCP). A two-year experiment with four irrigation levels based on crop growth stages was used to calibrate and validate RZWQM2, a hybrid model that combines the Root Zone Water Quality Model (RZWQM) and DSSAT4.0. The calibrated model was then used to investigate various irrigation strategies for high yield and water use efficiency (WUE) using weather data from 1961 to 1999. The model simulated soil moisture, crop yield, above-ground biomass and WUE in responses to irrigation schedules well, with root mean square errors (RMSEs) of 0.029 cm³ cm⁻³, 0.59 Mg ha⁻¹, 2.05 Mg ha⁻¹, and 0.19 kg m⁻³, respectively, for wheat; and 0.027 cm³ cm⁻³, 0.71 Mg ha⁻¹, 1.51 Mg ha⁻¹ and 0.35 kg m⁻³, respectively, for maize. WUE increased with the amount of irrigation applied during the dry growing season of 2001-2002, but was less sensitive to irrigation during the wet season of 2002-2003. Long-term simulation using weather data from 1961 to 1999 showed that initial soil water at planting was adequate (at 82% of crop available water) for wheat establishment due to the high rainfall during the previous maize season. Preseason irrigation for wheat commonly practiced by local farmers should be postponed to the most sensitive growth stage (stem extension) for higher yield and WUE in the area. Preseason irrigation for maize is needed in 40% of the years. With limited irrigation available (100, 150, 200, or 250 mm per year), 80% of the water allocated to the critical wheat growth stages and 20% applied at maize planting achieved the highest WUE and the least water drainage overall for the two crops.     

Nitrate leaching in a silage maize field under different irrigation and nitrogen fertilizer rates

Quantification of the interactive effects of nitrogen (N) and water on nitrate (NO₃) loss provides an important insight for more effective N and water management. The goal of this study was to evaluate the effect of different irrigation and nitrogen fertilizer levels on nitrate-nitrogen (NO₃-N) leaching in a silage maize field. The experiment included four irrigation levels (0.7, 0.85, 1.0, and 1.13 of soil moisture depletion, SMD) and three N fertilization levels (0, 142, and 189 kg N ha⁻¹), with three replications. Ceramic suction cups were used to extract soil solution at 30 and 60 cm soil depths for all 36 experimental plots. Soil NO₃-N content of 0-30 and 30-60-cm layers were evaluated at planting and harvest maturity. Total N uptake (NU) by the crop was also determined. Maximum NO₃-N leaching out of the 60-cm soil layer was 8.43 kg N ha⁻¹, for the 142 kg N ha⁻¹ and over irrigation (1.13 SMD) treatment. The minimum and maximum seasonal average NO₃ concentration at the 60 cm depth was 46 and 138 mg l⁻¹, respectively. Based on our findings, it is possible to control NO₃ leaching out of the root zone during the growing season with a proper combination of irrigation and fertilizer management.     

Morphological quality of sweet corn (Zea mays L.) ears as response to soil moisture tension and phosphate fertilization in Campeche, Mexico

In Mexico, corn production, part of which is sweet corn, is mainly destined for human consumption. In the present work, the morphological quality of sweet corn ears was assessed in response to four levels of soil moisture tension indicating irrigation start (−5, −30, −55, and −80 kPa) and three levels of phosphate fertilization (60, 80 and 100 kg ha⁻¹) in carstic soils in the south-east of Mexico. A factorial experimental design with three replicates was used. The following variables were determined: fresh weight (SCFWh), dry weight (SCDWh), diameter (SCDh), and length (SCLh) of sweet corn ears, all without husk, as well as number of kernels (NKxE), number of unfilled kernels (NUK), number of rows (NRxE), and dry kernel weight per ear (DKW). Yield of fresh (YFSCh) and dry (YDSCh) sweet corn ears, both without husk, and the harvest index (HI) were also determined. HI did not show significant statistical differences among irrigation or fertilization treatments. Regarding the other variables, the effect of the more humid treatments (−5 and −30 kPa) and the effect of the higher phosphorus doses (80 and 100 kg ha⁻¹) were statistically equal (P ≤ 0.01) with the lowest NUK and the highest values of all other variables; therefore, irrigation start at soil moisture tension of −30 kPa and phosphate fertilization application of 80 kg ha⁻¹ are recommended. At this level of soil moisture, the mean values over the three fertilization levels and all the replicates, obtained for SCFWh, SCDh, SCLh and NKxE were 198.5 g, 4.39 cm, 26.72 cm and 467 grains, respectively. According to the regression models, moisture tensions from −11.8 to −24.0 kPa, and phosphate fertilization doses from 87.7 to 102.2 kg ha⁻¹ minimize NUK and maximize the values of the rest of the variables. The highest irrigation water use efficiency was found in the moisture tension treatment of −30 kPa with an increase of 27 kg ha⁻¹ ears for each millimeter of applied irrigation water.     

Assessing yield optimization and water reduction potential for summer-sown and spring-sown maize in Pakistan

Agricultural food production in arid and semi-arid regions faces the challenge to ensure high yields with limited supply of water. This raises the question to which extent irrigation supply can be reduced without detriment to yield. Our study focuses on the yield-water uptake relationship for maize in the moderate water stress range in order to determine the onset of stress-induced dry-matter and yield losses. Compensatory plant responses under moderate stress levels are discussed in relation to seasonal climatic conditions.Summer-sown and spring-sown maize were irrigated with a decreasing amount of water in a field experiment in Pakistan. Water supply ranged from 100% water required to maintain soil at field capacity (FC) to 40% of FC. The average dry-matter and yield levels were slightly higher for summer-sown (15.0 Mg ha⁻¹) compared to spring-sown maize (13.1 Mg ha⁻¹). The onset of significant dry-matter and yield reduction started at the least irrigation treatment in both seasons. The amount of water required to avoid production losses was 272 mm in the summer-sown maize during the autumn growing season, and 407 mm for the spring-sown maize in the summer season, when the evaporative demand of the atmosphere was +27% higher. Water use efficiency (WUE_ET), normalized by vapour pressure deficit, of the summer-sown maize which was 10.0 kg kPa m⁻³, was +15% higher compared to the spring-sown crop; while the irrigation water productivity (2.9 kg m⁻³) was +11% more. WUE_ET increased over the whole range of applied water deficits for summer-sown maize, while the spring-sown crop showed a decreasing WUE_ET in the less irrigated treatment. Due to the higher efficiency in summer-sown maize, the potential in irrigation reduction without production losses (129 mm) was higher compared to the spring-sown maize (57 mm). Our results showed that in Pakistan water saving irrigation practices can be applied without yield loss mainly during the cooler growing season when the crop can efficiently compensate a lower total water uptake by increased use efficiency. For spring-sown maize the increasing evaporative demand of the atmosphere towards summer implies a higher risk of yield losses and narrows the range to exploit higher irrigation water productivity under moderate water deficit conditions.     

Effects of nutrition systems and irrigation programs on tomato in soilless culture

A research has been carried out to determine the effects of nutrition systems and irrigation programs on soilless grown tomato plants under polyethylene covered unheated greenhouse conditions. Two nutrition systems (open and closed) and three irrigation programs (high, medium and low) based on integrated indoor solar radiation triggering thresholds (1 MJ m⁻² [0.4 mm], 2 MJ m⁻² [0.8 mm] and 4 MJ m⁻² [1.6 mm]) in both nutrition systems have been tested. Applied and discharged nutrient solution, evapotranspiration, total and marketable yield have been measured and water use efficiency has been calculated. The highest total yield has been obtained from the open system with respectively 11% and 7.2% increases in autumn and spring. Applied nutrient solution volume and seasonal ET have been modified between 47.8-180.4 l plant⁻¹ and 41.7-145.5 l plant⁻¹ respectively during both growing seasons. As average of two growing seasons, respectively 826.5 and 330.6 m³ ha⁻¹ nutrient solutions have been discharged from the greenhouse in the open and closed systems. WUE of treatments varied between 33-55 kg m⁻³ in autumn and 26-35 kg m⁻³ in spring. Highest WUE values have been determined in 4 MJ m⁻² and in the closed system in both growing seasons. Results showed that the closed system and infrequent irrigations increased water use efficiency while decreasing yield and discharged nutrient solution.     

Water use, crop coefficients, and irrigation management criteria for camelina production in arid regions

Camelina sativa (L.) Crantz is an oilseed crop touted as being suitable for production in the arid southwestern USA. However, because any significant development of the crop has been limited to cooler, rain-fed climate-areas, information and guidance for managing irrigated-camelina are lacking. This study measured the crop water use of a November-through-April camelina crop in Arizona using frequent measurements of soil water contents. The crop was grown under surface irrigation using five treatment levels of soil water depletion. The seed yields of treatments averaged 1,142 kg ha⁻¹ (8.0% seed moisture) and were generally comparable with camelina yields reported in other parts of the USA. Varying total irrigation water amounts to treatments (295–330 mm) did not significantly affect yield, whereas total crop evapotranspiration (ET_c) was increased for the most frequently irrigated treatment. However, total ET_c for the camelina treatments (332–371 mm) was markedly less than that typically needed by grain and vegetable crops (600–655 mm), which are commonly grown during the same timeframe in Arizona. The camelina water-use data were used to develop crop coefficients based on days past planting, growing degree days, and canopy spectral reflectance. The crop coefficient curves, along with information presented on camelina soil water depletion and root zone water extraction characteristics will provide camelina growers in arid regions with practical tools for managing irrigations.