长白落叶松工业纤维林立地控制技术的研究

通过室外样地调查和室内木材材性分析及硫酸盐制浆实验,研究了不同立地条件下长白落叶松工业纤维林的生长过程、木材纤维特性、化学组成、物理性质和制浆特点,指出了立地条件对林分生长、木材纤维含量、纤维长度、纤维长宽比、得浆率、纸浆物理强度的影响。结果表明,长白落叶松工业纤维林生长最佳的立地条件是山地下部Ⅰ、Ⅱ地位级。立地条件对木材材性和纸浆特性有直接影响。在研究的林分密度和立地条件范围内,立地条件越差,木材纤维含量越少,纤维长度越短,纤维长宽比越小,1%NaOH提取物越多。而且这种现象有随林龄增长而加重的趋势。但立地条件对得浆率和纸浆的物理强度影响不明显。综合林分生长和木材材性,长白落叶松工业纤维林的培育最好在山地下部Ⅰ地位级和Ⅱ地位级的立地条件下进行。表4参17。     

长白落叶松纸浆林木材材性及纸浆特性的研究

长白落叶松纸浆林木材材性及纸浆特性的研究王树力，吴济生，仲崇淇（黑龙江省林业科学研究所哈尔滨１５０００４０）关键词长白落叶松，纸浆林，材性分析，纸浆特性纸浆林培育过程中，生物量是所有培育者关心的问题，而纸浆材材性及纸浆特性也是十分重要的内容，它涉及到...     

Effects of site preparation on emergence and early establishment of Larix olgensis in montane regions of northeastern China

Larix olgensis is one of the important commercial timber tree species in northeastern China, but it does not naturally regenerate in L. olgensis forests even after cutting. To identify the causes of the regeneration failure, the authors tested the effects of site preparation in a thinned stand and in a clearcut on the emergence and early establishment of L. olgensis seedlings. The results indicated that there was no correlation between cumulative emergence percentage (CEP) of L. olgensis seedlings and canopy openness, but the CEP was significantly affected by site preparation (P < 0.001). The average seedling survival rates after treatments consisting of removing both litter cover and understory vegetation cover were significantly higher in the clearcut than in the thinned stand (P < 0.001). Without site preparation, all seedlings in both the thinned stand and the clearcut disappeared within the first growing season, meaning that ground cover (understory vegetation cover and litter cover) was not beneficial to seedling survival. The average growth of seedlings exhibited significant differences between the thinned stand and the clearcut, and among the site preparations (P < 0.001). Intensely thinned stands without ground cover improved seedling growth. These results imply that light and ground cover might be the main factors limiting the early establishment of L. olgensis seedlings in managed plantation forests     

长白落叶松纸浆林培育措施对经济效益的影响(英文)

根据长白落叶松纸浆林的培育实践,以经济指标内部收益率和净现值为基础,分析了培育措施对经济效益的影响。结果表明:轮伐期越短,经济效益越高,立地级越高,经济效益亦越高。造林密度对经济效益的影响也较明显。在保证造林成活率和保存率的基础上,用于整地和幼林抚育方面的经费越少,经济效益则越高。选定的6项措施对财务指标的影响顺序为:轮伐期→立地条件→造林密度→管理费水平→幼林抚育强度→整地方式     

Influence of main site factors on Fraxinus mandshurica（Oleaceae） plantation

The investigation was carried out on 10-year-old plantation of Fraxinus mandshurica in Mao‘er Mountain Experimental Station of Northeast Forest University.tree height(H),diameter at breast height(D1.3) and the increment of tree height in 5 years (H5),the thickness of humus layer,as well as the soil moisture were measured for the plantation and the growth indexes(H,D1.3,H5) for different site conditions were analyzed.The results showedthat main site factors influencing the growth of Fraxinus mandshurica were soil moisture,gradient and location of siope in order.The growth of Fraxinus mandshurica was better on the middle-or up-slope site than on the down-slope site.Soil moisture and late frost caused by terrain are the main reasons that limit the growth of Fraxinus mandshurica plantation.     

Effect of growing site on the fundamental wood properties of natural hybrid clones of <Emphasis Type="Italic">Acacia</Emphasis> in Vietnam

We investigated clonal and site variations in wood fiber length, microfibril angle, and specific gravity of seven natural hybrid clones of Acacia (Acacia mangium × Acacia auriculiformis) grown in northern and southern Vietnam. Fiber length did not differ between clones or between sites. The microfibril angle of the S₂ layer did not significantly differ between clones but significantly differed between sites. Clone and site significantly affected specific gravity. The significant effects of genetic × environmental interactions on wood properties indicated the difference in the response of clones to different growing conditions. The trends of changes in fiber length, microfibril angle, and specific gravity from the vicinity of the pith to near the bark were similar for all clones at each site; however, variations in fiber length, microfibril angle, and specific gravity were more visible in northern Vietnam than in southern Vietnam, with a significant effect of genetic factors. This difference may be attributable to winter, which is experienced in northern Vietnam but not in southern Vietnam. For clone selection for plantation in the northern region, combining growth rate with wood properties was recommended. On the other hand, for plantation in the southern region, clone selection depends mainly on the growth rate, taking into consideration the specific gravity.     

Variation analyses of growth and wood properties of <Emphasis Type="Italic">Larix olgensis</Emphasis> clones in China

The growth traits (tree height, diameter at breast height, and stem straightness degree) and wood properties [wood density (WD), fiber length, fiber width, ash content (AC), lignin content, cellulose content, hemicellulose content (HEC), and holocellulose content] of 208 26-year-old Larix olgensis clones were analyzed. Except for WD and AC, there were significant differences (p < 0.01) for all traits among clones. The phenotypic coefficient of variation and repeatability of all traits were 9.34–35.33% and 0.218–0.930, respectively. Tree height and diameter at breast height showed significant positive correlation; however, the correlation coefficients among growth characteristics and wood properties were mostly not significant. Ten clones (L70, L56, L82, L90, L59, L91, L61, L92, L86, and L64) were selected as excellent clones under a selection rate of 5%, using tree height, diameter at breast height, and stem straightness degree as evaluation indexes, providing genetic gains of 28.69, 17.96, and 0.67%, respectively. Ten clones (L88, L305, L59, L66, L253, L304, L277, L298, L248, and L293) were selected as excellent clones using wood properties as an evaluation index, with a selection rate of 5%, providing genetic gains in WD, fiber length, fiber width, cellulose content, and HEC of 4.14, 3.64, 9.28, 6.77, and 9.61%, respectively. This study provides a theoretical basis for selecting excellent L. olgensis clones.     

落叶松种间及其杂种生长与形质性状评价研究

[目的]通过对落叶松种间及其杂种生长与形质性状评价来定向选育优良落叶松建筑材。[方法]以辽宁省大孤家林场32年生的落叶松试验林为实验材料,对落叶松属日本、兴安、长白及华北4个落叶松种,及以日本落叶松为母本的日本×兴安、日本×华北、日本×长白、日本×日本杂种的生长和形质性状进行变异规律分析,并采用模糊数学隶属函数对其差异显著指标进行综合评价。[结果]表明:落叶松种和杂种间生长差异显著(p<0.01),杂种胸径、树高和材积总生长量与母本差异不显著,却显著高于相应父本;杂种之间的生长差异体现在林分的前10年,随着林龄的增大优势逐渐减退;树冠特征因子中的枝下高、冠长、枝条直径、长度、角度和干形特征因子中的高径比、树干圆满度、节子直径、长度、角度在落叶松种和杂种间差异显著。基于上述指标进行了生长和形质性状综合评价,排名前三位的分别为日本×兴安、日本×长白和日本落叶松。32年生时日本×兴安的胸径、树高和材积分别为18.69 cm、21.62 m和0.339 2 m³;日本×长白的为18.44 cm、23.85 m和0.339 6 m³;日本落叶松的为19.36 cm、21.31 m和0.335 7 m³;而且它们在适应性上也具有明显优势。[结论]日本×兴安、日本×长白和日本落叶松适合作为定向培育建筑材的优良品种在东北地区重点推广。     

Study on tracheid variation ofPicea koraiensis (nakai) in natural stand and plantation

Tracheid characteristics ofPicea koraiensis from natural stand in Liangshui area and plantation in Mao'ershan area were studied. The results of variance analysis showed that the tracheid length, diameter, and thickness of tracheid wall were significant differences between the growth rings. All those characteristics tend to increase from heart-center to bark. In natural stand, it has positive correlation between the characteristics. In plantation, the tracheid length has positive correlation with the trachied diameter, while both the trachied length and the trachied diameter has negative correlation with the thickness of trachied wall. The tracheid length and diameter have no significant difference in growth between natural stand and plantations. The thickness of tracheid wall from the plantation is a little thicker than that from the natural stand before 15 years. Foundation item: This paper was part of State 9th Five-Year Plan project of “Early Mensuration ofPicea koraiensis (nakai)”. Biography: REN Xu-qin (1973-), female, graduate student in Northeast Forestry University, Harbin 150040, P. R. China. Responsible editor: Song Funan     

长白落叶松纸浆材优良家系多性状联合选择研究

采用胸径木芯与伐倒木取样方法,对24年生长白落叶松优树子代测定林14个处理的生长性状、木芯材质性状、解析木材质性状及其制浆造纸特性进行了研究,结果表明:生长性状、木芯基本密度、木芯管胞性状均存在丰富的变异;家系间生长性状差异极显著;木芯基本密度、木芯管胞性状差异显著,家系遗传力在0.56 0.80之间;解析木基本密度、早材微纤丝角、管胞长度、早材壁腔比、木质素、阿拉伯糖含量、抗张强度、撕裂度等差异极显著,家系遗传力在0.64 0.86之间;晚材率、管胞长宽比、综纤维素含量等差异显著,家系遗传力在0.51 0.61,家系水平的材性改良潜力较大。生长性状与木芯管胞长度呈极显著正相关,与木芯基本密度、管胞长宽比相关不显著;木芯基本密度、管胞长度、管胞宽度以及管胞长宽比与解析木相应性状呈极显著正相关关系,且回归模型较为理想,可以利用胸径木芯各性状值预测其单株值,间接选择和评价纸浆材优良家系。通过生长性状、木芯基本密度和木芯管胞长宽比综合分析选出166、169为优良家系,根据解析木生长、材质以及纸张物理性状选出的优良家系与其结果一致。优良家系材积、木芯基本密度和木芯管胞长宽比的遗传增益(超过对照)分别为48.34%(38.80%)、14.01%(3.63%)和19.89%(6.42%)。     

Effect of stand and tree attributes on growth and wood quality characteristics from a spacing trial with Populus xiaohei

The effect of stand density (1000 stems/ha, 500 stems/ha and 250 stems/ha) on tree growth and wood quality characteristics was studied in a 27-year-old plantation species of Populus xiaohei in China. Results indicated that stand density had significant effects on tree radial growth and crown size, and the lowest stand density produced trees with the largest stem taper. In terms of wood quality characteristics, there was no significant effect of stand density on either wood basic density or fiber length. However, significant differences were found between different stand densities for wood mechanical properties. A positive relationship between modulus of elasticity, compression strength and stand density was observed, while the highest modulus of rupture was recorded at a moderate density of 500 stems/ha. Stand density was responsible for highly significant effects on both juvenile wood and wet heartwood basal areas in individual trees, and there was an obvious tendency towards increasing juvenile wood and wet heartwood basal areas with decreasing stand density. In addition, the relationships between wood quality characteristics and tree and stand characteristics were also examined. Some wood quality characteristics, namely mechanical properties and juvenile wood and wet heartwood basal areas, were quantified successfully in relation to selected tree characteristics using a regression approach with various degrees of goodness of fit. Based on comprehensive consideration of various factors, such as wood quality, tree growth, and establishment cost, results from this study suggest that a density of 500 stems/ha is optimum for wood production.     

鹅掌楸人工林的丰产特性

闽北山地多种阔叶树的对比造林试验和鹅掌楸人工林经营研究表明,鹅掌楸具有适应性强、早期速生等丰产特性,是南方基地造林的优良阔叶树种。造林后第３年鹅掌楸即进入速生阶段,在较好的立地上,８年生时平均树高１２．６ｍ,平均胸径１２．４ｃｍ,立木蓄积年生长量超过１６ｍ＾３．ｈｍ＾２。可利用较好的立地纯林经营,并根据培育目标设计不同的安植密度。在较差的立地上与桤木、木荷、杉木、建柏等混交效果较好。鹅掌楸叶大量多,不论纯林还是混交林对土壤培肥作用都很明显。     

The pulping and papermaking characteristics of youngL.gmelini andB.platyphylla

5, 10, 15, and 20 year oldLarix gmelini andBetula platyphylla were used as pulping raw material in the research. The examination of youngL. gmelini andB. Platyphylla fibrous structures showed that the fiber length and ratio of length to width of 5 years oldL. gmelini noticeably differed from that of matureL. gmelini. but that of 5 year oldB. platyphylla were nearby equal to that of matureB. platyphylla. The research results indicated that 15 years oldB. platyphylla and 20 year oldL. gmelini were best suited to pulping among the eight experimental raw materials; 10 years oldB. platyphylla and 15 year oldL. gmelini were optimal to the ratio of beating degree increment and corresponding beating time. The pulp characteristics of 15 year old B. platyphylla and 20 year oldL. gmelini were similar to those of mature wood, and it was feasible to consider 15 years toB. platyphylla and 20 years toL. gmelini as their rotation period; 10 years and 15 years as their thinning cycles for the papermaking forest base.     

The coppice-with-standards silvicultural system as applied to Eucalyptus plantations — a review

We review the management of Eucalyptus species under a coppice-with-standards （CWS） silvicultural system. CWS management results in product diversification, permitting production of small and large scale timber from the same stand. Eucalyptus species are suitable candidates for CWS management because： there are large worldwide plantation areas, sprouting capacity is high, and eucalypts are multipur- pose species. We discuss （1） short rotation Eucalyptus coppice manage- ment for energy and pulping and （2） Eucalyptus seedling management for solid wood products. We review the literature and discuss experi- ences with Eucalyptus managed under the CWS system. We also assess projects dealing with Eucalyptus coppice management, stand density regulation, pruning, and stand and wood quality. The growth environ- ment of the standard trees （heavy competition up to the first harvest, free growth afterwards） coupled with long rotations （〉20 years） results in high quality logs for solid wood products. Early pruning should be ap- plied to enhance wood quality. We propose a system for the silvicultural management of Eucalyptus under the CWS system, elaborating on the consequences of initial planting density, site productivity, and standard tree densities as well as timing of basic silvicultural applications.     

培育措施对人工林樟子松木材力学性质的影响

研究了不同培育措施(初植密度、间伐强度、坡向、坡位)对人工林樟子松(Pinus sylvestris var.mongolica)木材的密度和力学性质(横纹抗弯强度、抗弯弹性模量、顺纹抗压强度、冲击韧性、端面硬度)的影响。初植密度(1.5m×1.0m,1.5m×2.0m和1.5m×2.5m)对木材密度和抗弯弹性模量有显著的影响。初植密度为1.5m×1.0m时,木材主要力学指标值最大。适当间伐可提高木材的抗弯弹性模量和顺纹抗压强度,但重度间伐则会降低木材的力学强度。坡向(阳坡和阴坡)对木材的抗弯弹性模量影响显著,阳坡高于阴坡。坡位(上坡位和下坡位)对除端面硬度外的木材力学性质指标影响都显著,各项力学指标值均是坡下高于坡上。表5参9。     

Determination of the distribution and reaction of polysaccharides in wood cell walls by the isotope tracer technique VII: Double radiolabeling of xylan and pectin in magnolia (Magnolia kobus DC) and comparison of their behaviors during kraft pulping by radiotracer technique

myo-Inositol-[2-³H] and d-glucuronic acid-[6-¹⁴C] were administered simultaneously to a growing stem of magnolia (Magnolia kobus DC) to label xylan and pectin, respectively, in the cell wall. Determination of the radioactivity of nitrobenzene oxidation products and sulfuric acid hydrolysates of the newly formed xylem indicated that xylan and pectin were labeled with ³H and ¹⁴C, respectively. The doubly labeled wood tissue was treated to kraft pulping, and the radioactivity of the pulping black liquor and treated wood tissue were determined at various stages of the pulping to compare the dissolving behavior between pectin and xylan during the pulping. The results showed that pectin was not dissolved as easily as xylan and was not redeposited on pulp fiber at the late stage of the pulping.Part of this report was presented at the 40th Lignin Symposium at Tsukuba, October 1995     

Optimal management of larch (<Emphasis Type="Italic">Larix olgensis</Emphasis> A. Henry) plantations in Northeast China when timber production and carbon stock are considered

? Key message

The optimal management of larch (Larix olgensis) plantations in Northeast China consisted of 2 or 3 thinnings and a rotation length of 55–61 years when economic profitability, wood production, and carbon sequestration were simultaneously maximized. Wood production ranged from 5.4 to 11.7 m³ ha^?1 a^?1, depending on site quality.

? Context

L. olgensis is an important tree species in the northeast forest region of China, playing a significant role in the establishment of fast-growing and high-yielding plantation forests in China. However, the management of these plantations has not been optimized in previous studies.

? Aims

The objective of the study was to find the optimal combinations of thinning times, thinning types, and rotation length for L. olgensis stands when both timber production and carbon stock are considered.

? Methods

First, a growth and yield model was developed to simulate the dynamics of larch plantations. Then, the models were linked with the Hooke and Jeeves optimization algorithm to optimize forest management for two commonly used planting densities and three site qualities.

? Results

Two thinnings were found to be suitable for larch plantations when the stand density at 10 years was 2125 trees/ha (corresponding to a planting density of 2500 trees/ha) whereas three thinnings were recommended when the density at 10 years was 2800 trees/ha (planting density of 3300 trees/ha). When the stand density was 2800 trees/ha, the optimal rotation length was 61, 58, and 55 years for site indices (SI) 12, 16, and 20 m (dominant height at 30 years), respectively. The mean annual wood production was 5.4 m³ ha^?1 for SI 12, 8.2 m³ ha^?1 for SI 16, and 11.7 m³ ha^?1 for SI 20. The results were nearly the same for the lower initial stand density. The better the site quality of the stand, the earlier the thinnings were conducted.

? Conclusion

In multifunctional forestry, optimal rotation lengths of larch plantations were 10–20 years longer than advised in the current silvicultural recommendations for Northeast China.

     

香叶树人工林木材纤维形态特征的研究

通过对香叶树人工林木材纤维形态的测定表明：香叶树人工林木材在1～3 a间木纤维长度属短;在3～18 a间木纤维长度属中等长度。香叶树人工林木材在1～5 a间木纤维长宽比较小,在6～18 a间木纤维长宽比大于45。     

Influence on pulping yield and pulp properties of wood density of Acacia melanoxylon

Wood density and pulp yield are key parameters in the evaluation of tree productivity and quality for pulping and their relationships are of high practical importance. The influence of wood density on pulp yield and other pulp quality parameters was investigated using Acacia melanoxylon and its natural variability as a case study. Twenty trees were harvested (five trees in each of four sites in Portugal), and wood discs taken at different height levels, from the base to the top of the tree, providing 100 wood samples, covering the natural variability of wood density ranging from 449?kg?m^?3 to 649?kg?m^?3. Under the same experimental conditions of kraft pulping, screened pulp yield ranged 47.0?C58.2?%, Kappa number 10.9?C18.4, ISO brightness 14.9?C45.6, fibre length 0.660?C0.940?mm and fibre width 16.2?C22.9???m. The pulp yield and Kappa number were not correlated with wood density. Higher pulp yields were associated with lower Kappa numbers and alkali consumption, suggesting the important role of chemical composition of wood on kraft cooking. The results confirm the high pulping potential of Acacia melanoxylon trees grown in Portugal and suggest the possibility of tree selection using both wood density and pulp yield.