Fundamental studies on the hydrodynamic resistance of small pot traps

ABSTRACT:   The hydrodynamic resistance of small pot traps has been conducted in order to establish some basic information. The specific objectives of the study was to measure the hydrodynamic force and estimate the critical setting condition for traps. Five types of traps with different materials were used in the experiment: a netted semi-cylinder shape, a wire semi-cylinder shape, a heart shape, a box shape, and a cylinder shape. The hydrodynamic force of each trap was measured in a flume tank. Flow speeds in the flume tank were 0.1, 0.2, 0.3, 0.4, and 0.5 m/s. Attack angles for this study were 0, 15, 30, 45, 60, 75, and 90 degrees. At an attack angle of 0 degrees the main axis of the trap was parallel to the water flow and at 90 degrees it was vertical. The values of the hydrodynamic drag coefficient varied with traps: netted semi-cylinder shape, 2.75–5.96; wire semi-cylinder shape, 2.81–4.49; heart shape, 2.77–3.66; box shape, 2.39–2.97; and for cylinder shape, 3.57–3.67. The flow speed (0.5 m/s) was effective to set the netted semi-cylinder, wire semi-cylinder, box, and cylinder shaped traps. The same flow speed applied to the heart-shaped trap was only effective to a maximum of 30 degrees attack angles and below.     

聚乙烯编织线替代普通聚乙烯捻线对拖网性能的影响

聚乙烯编织网线比普通聚乙烯捻线强度高,用编织线来替代目前的普通捻线,可降低拖网渔具的阻力从而达到节能降耗的目的。本文通过实际取样测试,比较了两种网线的拉伸性能,在不降低原拖网渔具的单线结强力的前提下,用聚乙烯编织线代替原普通捻线,并通过模型试验研究其对拖网渔具性能的影响和节能效果。结果表明:单线结强力相同的两种网线,编织线的直径可比普通网线的直径下降15.17%以上。本试验编织线拖网的平均网线直径比原普通捻线拖网下降16.00%,网具阻力面积(线面积)从304.57 m2下降到256.47 m2,下降了15.79%。同等试验条件下,编织线拖网的阻力比普通捻线拖网下降17.25%左右,而网口高度的变化则不明显。能耗系数的计算结果为编织线拖网过滤同体积的水体所消耗的能量比普通捻线拖网下降16.67%。功率消耗的分析表明,消耗同样的功率,440 kW的双拖渔船使用编织线拖网,拖速可比普通捻线拖网提高8.33%,如采用和普通捻线拖网同样的拖速作业,则去掉起、放网所消耗的时间,以一天正常拖网作业18 h计算,可节约燃油77 L左右。     

Effects of entrance design on catch efficiency of arabesque greenling traps: a field experiment in Matsumae, Hokkaido

ABSTRACT:   A field experiment was conducted in the Matsumae area of Hokkaido, Japan, during June and July 2002, to investigate the effects of different entrance designs on the catch efficiency of fish traps by fishing with commercial traps (entrance inclination angle [α] = 37°; funnel length of entrance [ L _f ] = 22 cm) and experimental traps. The experimental traps were of the same size and similar design as commercial traps, with different entrance inclination angles (trap E1: α = 46°; E2: α = 27°; E3: α = 0°; all L _f  = 22 cm) or funnel lengths (E4: α = 37°, L _f  = 8 cm). In total, 2200 fish during 200 trap hauls were captured. The catch was significantly higher using both traps E2 and the commercial trap than with trap E3 ( P  < 0.05), and the catch of trap E2 was higher than that of the commercial trap. There were no significant differences in mean fish body length or the frequency distributions of body length among trap types (E1, E2, E3 and commercial). The funnel length of the entrance also affected the catch of traps. Trap E4 had significantly higher catches than the commercial trap ( P  = 0.04) when traps were deployed for a 1-day soak time. Fish body length frequency distributions did not differ between trap E4 and the commercial trap. The results showed that catch can be greatly affected by trap entrance designs.     

Evaluation of a by-catch reduction device for glass eel fishing traps

Abstract  The effectiveness of a new design of glass eel, Anguilla anguilla (L.), fishing trap was tested in the Ebro River delta fishery (Eastern Mediterranean, Spain). The modified fishing trap incorporated a by-catch reduction device (BRD) to increase trap selectivity and minimise by-catch of non-targeted fish, without affecting glass eel captures. The BRD is inexpensive and easy to implement, consisting of a cylinder covered with a rigid square-mesh of 2.0–2.4 mm knot-to-knot, which is easily fitted to the fishing trap entrance. Testing of the BRD was made by paired comparisons between captures of targeted and non-targeted fish species from both conventional and BRD-modified traps. The use of a BRD in the glass eel traps resulted in a 68.9% reduction in the number of captured non-targeted fish specimens, while it did not reduce glass eel yields. The BRD implementation was fully effective for all species and individuals with sizes >40 mm total length, with the exception of the black-striped pipefish, Syngnathus abaster Risso. These results support the implementation of the BRD in glass eel fisheries along the Eastern coast of the Iberian Peninsula where these fishing traps are used.     

高分子编结网片水动力特性水槽试验研究

高分子渔用材料在设施养殖和海洋渔业中的应用越来越广泛,对其水动力特性进行研究十分必要。试验采用不同网目系数和网线粗度的高分子编结试验网片进行水槽试验,倾角从0°变化到90°,设置水流速度从0.3 m/s开始,以0.1 m/s为梯度,逐渐增大至1.3 m/s。为减小尾流和湍流对试验结果的影响,使用流线型框架固定装配。经试验得到以下结果:(1)在网片与水流垂直时,阻力系数有随网目系数增大而增大的趋势,而在网片与水流平行时,阻力系数随网目系数增大而减小。(2)阻力系数有随雷诺数增大而逐渐减少的趋势,网片平面与流体运动方向速度垂直时,阻力系数在13001500后阻力系数变化不大。(3)阻力系数随着冲角的增大而增大并最终趋于稳定值。(4)升阻力系数比(K)在总体上有随倾角变大而先变大再变小的趋势,K的极值均出现在20°到30°内,最大K值约为0.41。(5)网片与水流垂直时,在1000相似文献   

网衣缩结对圆柱形网箱性能影响的初步研究

采用网箱模型试验,对周长50m、深8m的HDPE双管圆形重力式网箱,通过改变网衣装配方法,在不同流速条件下对网箱性能进行了研究。结果表明,菱形目装配缩结系数0．707时网箱的阻力比0．65时小,但在静态时,缩结系数0．707比0．65时容积损失率大;力纲装配对网箱在水流作用下的形态产生影响。     

Effect of temperature on the swimming endurance and post-exercise recovery of jack mackerel <Emphasis Type="Italic">Trachurus japonicus</Emphasis> as determined by ECG monitoring

The effect of temperature on the swimming performance of jack mackerel Trachurus japonicus was examined in a flume tank by measuring the swimming endurance time and heart rate. The lower swimming performance was observed at 10°C (the lowest temperature tested), manifesting as the shortest endurance time and the slowest maximum sustained speed. ECG measurements of the heart rate under free-swimming conditions at zero flow velocity revealed a temperature effect, with 25.3 beats/min observed at 10°C, 38.9 at 15°C, and 67.2 at 22°C. The heart rate also increased with swimming speed to maximum levels of 60, 125, and 208 beats/min, respectively, at these three temperatures. Heart rate recovery times measured after the fish had been swimming at prolonged speed tended to increase with temperature, while a negative correlation resulting in relatively short recovery times was observed after swimming at close to the burst swimming speed at each water temperature.     

Experimental study of the drag on fine-mesh netting

The hydrodynamic forces on netting have been investigated by many researchers. They proposed equations to estimate the drag and lift coefficients of the netting, taking the effects of the Reynolds number and solidity ratio into account. However, there are few studies on the hydrodynamic forces on netting with a fine mesh, which is sometimes used in Japan for farming small fish, such as young sardines. The size of the fine mesh is a few millimeters, whereas the solidity ratio of the netting is similar to that of standard netting. The drag on fine-mesh netting may increase because of the effects of blocking. In the present study, the drag on fine-mesh netting was examined by means of a towing experiment in a water tank. The experiment included an investigation of the drag on a planar net, a half-circular net, a circular net, and a circular net with a bottom, to understand the effect of the attack angle of the water current and wake. As a result, the drag coefficient of the plane net was in the range of those proposed in the previous studies. The effect of the attack angle of the water current was approximately reproduced by the cosine function. The reduction factors for the water current velocity through the circular net also agreed with those proposed in the previous studies, whereas it was approximately at the maximum among the previous estimations. Consequently, the drag on fine-mesh netting could be well explained by the estimates from the previous studies. However, the drag at the bottom of the net, parallel to the water current, was overestimated if hydrodynamic forces act on each transverse twine normal to the flow direction. The effects of the interactions among the twines, which are aligned parallel to the flow direction, should be specifically examined as a future study.     

Influences of hanging ratio,fishing height,twine diameter and material of bottom-set gillnets on catches of dusky flathead <Emphasis Type="Italic">Platycephalus fuscus</Emphasis> and non-target species in New South Wales,Australia

ABSTRACT:   Three experiments were done to test for the influences of different (i) hanging ratios (E = 0.5, 0.65 and 0.8); (ii) fishing heights (25 and 12 meshes); and (iii) twine diameters (0.41, 0.56 and 0.62 mm) and materials (multifilament nylon and multimonofilament nylon polyamide) on catches and by-catches in the estuarine gillnet fishery for Platycephalus fuscus in New South Wales, Australia. In each experiment, the various 100-m treatment panels comprising 80-mm (nominal) mesh rigged according to the different configurations being examined were configured in a single gang between 1090 and 1310 m in length, and fished according to commercial practices. The results showed no significant differences between different hanging ratios or twine diameters for the numbers, weights and size compositions of catches and by-catches. Twine material had an effect on only one key by-catch species ( Acanthopagrus australis ), with fewer caught in panels made from multifilament nylon compared with multimonofilament nylon. In contrast to the above modifications, lowering the fishing height of the floatline significantly reduced total by-catch by up to 46% and the individuals of key by-catch species ( Mugil cephalus , A. australis and Girella tricuspidata ) by between 60 and 85% with no effect on catches of targeted P. fuscus , or legally retained byproduct, Portunus pelagicus . The results are used to provide directions for the future management of this fishery and have relevance to other similar bottom-set gillnet fisheries.     

Temperature effect on heart rate of jack mackerel Trachurus japonicus during swimming exercise

The heart rate of jack mackerel [16.5–21.2 cm fork length (FL), n = 24] was examined through forced swimming exercise in a flume tank by 10-min step-ups of speed levels in 1.5–6.0 FL/s range at different temperatures of 10, 15, and 22 °C. Electrocardiograph (ECG) monitoring was conducted by comparing the heartbeat pattern in still water without flow as a control, and continuously during exercise by speed levels until fatigue and during the recovery phase. Average heart rates in the control at each temperature were 36.5 beats/min at 10 °C, 56.1 beats/min at 15 °C, and 75.2 beats/min at 22 °C. The heart rate of jack mackerel significantly increased as the swimming speed was increased in each temperature. At the lower swimming speed of 1.5–2.4 FL/s, the heart rate was the same level as the control value at each respective temperature. The heart rate started to increase at swimming speeds of 2.3–2.5 FL/s at all temperatures. The higher heart rate in the range of 150–200 beats/min was achieved at a swimming speed of 6.0 FL/s at 22 °C. The recovery time after the maximum heart rate at high speed became longer at high temperatures.     

Fatigue analysis of the jack mackerel <Emphasis Type="Italic">Trachurus japonicus</Emphasis> by electrocardiographic monitoring during prolonged swimming

The effect of fatigue on swimming performance was examined by measuring the swimming endurance time and heart rate of the jack mackerel Trachurus japonicus [15.7 ± 0.8 cm fork length (FL), n = 15] during forced exercise in a flume tank at fixed swimming speeds of 4, 5 and 6 FL/s. Electrocardiographic (ECG) monitoring during the experimental process from control (0.8 FL/s) to exercise phase revealed a rapid cardiac response of T. japonicus to the elevation of swimming speed. The heart rate of T. japonicus significantly increased from the control level of 52.9 beats/min at a slow flow speed of 0.8 FL/s to 148.2 beats/min at 4 FL/s, 168.6 beats/min at 5 FL/s and 183.2 beats/min at 6 FL/s. During the fixed speed test, the heart rate of each individual fish was stabilized without any recognizable increase or decrease until the fish failed to swim because of fatigue. Fatigue analysis on endurance time demonstrated that prior swimming experience at prolonged speeds would impair the endurance performance during subsequent swimming exercise. Recovery time of the heart rate after the fish was fully exhausted by prolonged fast exercise increased with increasing swimming endurance time.     

鳙幼鱼下行过坝的水力导鱼栅实验

分析不同叶片角和布置角下导鱼栅的导鱼效果,获取最优的导鱼栅布置方式,为下行过鱼设施设计提供理论依据及参考。以鳙(Aristichthys nobilis)幼鱼为研究对象,通过设置导鱼栅布置角度(15°、30°、45°)和叶片角度(15°、30°、45°、90°),在室内开展模型实验,分析鳙从导鱼旁路下行(引导成功)和从导鱼栅叶片间隙下行(引导失败)的通过率,确定最优运行工况。结果表明:在所有工况下,实验鱼均出现了顶流现象,但顶流率均小于50%;导鱼栅布置角和叶片角同为30°时,辅助鱼类下行的成功率最高,达95%;其他工况下,成功率均低于75%。导鱼栅附近的水力条件表明,流速沿着导鱼栅方向呈现波浪线上升,紊动能分布总体呈现先上升后下降的趋势,紊动能范围为0~0.0032 m²/s²。     

Estimation of basket trap selectivity for changeable nassa (Nassarius mutabilis) in the Adriatic Sea

Size selectivity of basket traps for changeable nassa (Nassarius mutabilis) was estimated through comparative fishing trials with traps varying in mesh size and net colour. Selectivity curves of two commercial (19 mm white twine and 19 mm black twine) and three experimental (23, 26 and 28 mm white twine) traps were estimated using SELECT method. In addition, theoretical size-selectivity curves were calculated from morphometric data using a simplified version of Sechin method.Differing from the opinion of fishermen, N. mutabilis did not show any preference for dark coloured twine. Retention curves estimated with SELECT method had a very sharp selectivity and well fitted catch data in all cases. Theoretical size-selectivity curves were very close to size-selectivity curves obtained from experimental data. The two types of curve were very similar in shape, although the theoretical ones were shifted towards larger size classes and showed a slightly steeper slope than SELECT curves. The mesh size commonly used by fishermen is not adequate for rationally exploiting the resource, as catches mainly included undersized specimens, whilst the 23 and 26 mm mesh sizes would represent a good compromise between reduced occurrence of undersized individuals and satisfactory yields of commercial product.     

A two-chambered trap reduces within-trap predation by octopus on rock lobsters in aquarium trials

A two-chambered lobster trap was developed that in aquarium trials significantly (p < 0.01) reduced octopus predation on trap-caught spiny lobster. The trap was designed using information gained from an investigation of the behavioural interactions of the maori octopus (Octopus maorum) with traps used in the South Australian commercial lobster (Jasus edwardsii) fishery. This study showed that octopuses were primarily attracted to traps by the presence of bait as opposed to lobsters and that octopus entry into traps was ‘fortuitous’ and mediated by speculative exploration. The outer chamber of the modified trap contained bait and allowed entry by octopuses but not lobster and the inner chamber allowed access to both animals. The trap worked on the principle that octopuses would enter the outer chamber containing bait via a side entrance in preference to entry to the inner chamber containing lobsters via the neck. This was found to be the case and lobster mortality was 70% lower in the two-chambered trap than a standard trap. Successful adaptation of this trap design to commercial fishing conditions could significantly reduce rates of octopus predation on rock lobsters in several important southern hemisphere fisheries for spiny lobsters.     

Estimating attraction areas and effective fishing areas for Chilean lemon crab (Cancer porteri) using traps

The applicability of a method, based on varing distance between traps, for estimating attraction area (A_at) and effective fishing area (A_ef), for Cancer porteri caught with experimental traps, was tested. Based on fishing experiments, where lines of traps were set with different spacing between them, the minimum distance at which A_at of adjacent traps did not overlap was estimated. This provided an estimate of A_at of 9348 m²/trap. To estimate A_ef, an exponential decay function for the probability of capture within the A_at was assumed; A_ef was estimated at 577 m²/trap, similar to values estimated for other shallow water crustaceans using SCUBA for calibration. This is inferior to estimates calibrated with underwater photography for crustaceans at greater depths.     

Survival of migrating sea trout (Salmo trutta) and Atlantic salmon (Salmo salar) smolts negotiating weirs in small Danish rivers

Abstract – The survival of brown trout and Atlantic salmon smolts during passage over small weirs was estimated in two small Danish rivers during the spring of 1998. Parallel groups of smolts were released upstream and downstream of the weirs and recaptured in traps further downstream. The results showed a smolt loss varying from 18 to 71% for trout and 53% for salmon. Furthermore, the surviving smolts from the upstream groups were delayed for up to 9 days compared to downstream groups. The study demonstrated that an increased proportion of total river discharge allocated to fish passage increased the smolt survival. Losses may be because of fish penetrating grids erected at fish farm inlets, predation and delays, which may lead to desmoltification. The low survival may seriously threat both the long-term viability of wild populations of anadromous salmonids and the outcome of the intensive stocking programme in Denmark.     

Influences of twine diameter and mesh area on the efficiency and durability of baited hoop nets targeting portunids

The utility of varying twine diameter (0.5–0.8 mm Ø) and/or mesh area (0.5:1) in south‐eastern Australian recreational hoop nets was assessed in response to concerns over (1) impacts to discarded, undersize Scylla serrata L. and Portunus pelagicus Forskål and (2) marine debris (lost meshes). There was a negative relationship between Ø and breakage, with more in the narrowest (16.16–18.42 meshes deployment^?1) than thickest (8.79–4.68) twines. Mesh damage was also affected by interactions between netting area and (1) soak time (only S. serrata) and (2) catches, with all nets similarly damaged during <3.5‐h soaks, or when only one crab was caught, beyond which the large‐area nets incurred more. Irrespective of net, there were consistent positive relationships between mesh damage and water temperature, and more damage overnight. Large crabs took longer to remove, but more so from thicker‐twined and large‐area nets, and some also sustained the most damage. Twine diameter did not affect S. serrata catches, but was negatively associated with catches of P. pelagicus, while the small‐area nets caught proportionally (to area) fewer portunids. The results reflect species‐ and size‐specific behavioural variability, but support using thick twine and limiting deployment durations for hoop nets. Alternatively, other less controversial traps might offer a more holistic solution to the stated concerns.     

Swimming performance of wild and F1-hatchery-reared Atlantic salmon (Salmo salar) and brown trout (Salmo trutta) smolts

Abstract –  The swimming performance of wild and hatchery-reared smolts of two salmonid species was investigated. Wild Atlantic salmon smolts (WS) and brown trout smolts (WT) of equal size were caught in fish traps during migration. Hatchery-reared smolts of both species (HS and HT for salmon and trout respectively) were first generation offspring from wild broodstock. The swimming performance of individual smolts from the four groups (WS, HS, WT, HT) was tested three consecutive times using a swimming flume with water flowing at a start rate of 0.16 m·s⁻¹ and a constant acceleration rate of 0.167 cm·s⁻² (10 cm·s⁻¹·min⁻¹). Wild caught smolts of both species performed significantly better than those reared in hatchery conditions. The WS group were observed to maintain an average swimming speed ( U _burst) that was 30% faster than the HS group, whereas the wild trout smolts were superior to HT by approximately 25%. Repeated measures revealed species-specific exhaustion patterns. Brown trout smolts maintained consecutive U _burst indicating significant stamina compared with Atlantic salmon smolts that were found to be exhausted by the initial trial.     

Drag force acting on biofouled net panels

Measurements were made to assess the increase in drag on aquaculture cage netting due to biofouling. Drag force was obtained by towing net panels, perpendicular to the incident flow, in experiments conducted in a tow tank and in the field. The net panels were fabricated from netting stretched within a 1 m² pipe frame. They were towed at various speeds, and drag force was measured using a bridle-pulley arrangement terminating in a load cell. The frame without netting was also drag tested so that net-only results could be obtained by subtracting out the frame contribution. Measurements of drag force and velocity were processed to yield drag coefficients.

Clean nets were drag tested in the University of New Hampshire (UNH) 36.5 m long tow tank. Nets were then exposed to biofouling during the summer of 2004 at the UNH open ocean aquaculture demonstration site 1.6 km south of the Isles of Shoals, New Hampshire, U.S.A. Nine net panels were recovered on 6 October 2004 and immediately drag tested at sea to minimize disturbing the fouling communities. The majority of the growth was skeleton shrimp (Caprella sp.) with some colonial hydroids (Tubularia sp.), blue mussels (Mytilus edulus) and rock borer clams (Hiatella actica). Since the deployment depth was 15 m (commensurate with submerged cages at the site), no algae were present. The net panels had been subject to several different antifouling treatments, so the extent of growth varied amongst the panels. Drag force measurements were made using a bridle-pulley-load cell configuration similar to that employed in the tow tank. Fixtures and instruments were mounted on an unpowered catamaran that was towed alongside a workboat. Thus, the catamaran served as the “carriage” for field measurements.

Increases in net-only drag coefficient varied from 6 to 240% of the clean net values. The maximum biofouled net drag coefficient was 0.599 based on net outline area. Biofouled drag coefficients generally increased with solidity (projected area of blockage divided by outline area) and volume of growth. There was, however, considerable scatter attributed in part to different mixes of species present.     

Post-stocking dispersal of European grayling,Thymallus thymallus (L.), in a semi-natural experimental stream

Abstract Artificially hatched and reared juvenile European grayling, Thymallus thymallus (L.), from three natural populations were released into an experimental stream. Two of the populations were from lakes and the third population was from a river. Post-stocking dispersal was studied by recapturing fish in traps and by electric fishing after each of the stocking exercises. On all three occasions the first fish to be recaptured were caught in a trap about 400 m downstream from the release site, within 5–12 min of release. Proportions of stocked grayling juveniles recaptured by electric fishing in the fast-flowing section of the experimental stream (the rapids) were 9.9%, 46.7% and 16.6% after the first, second and third stocking, respectively. No significant population-specific difference was found between fish caught in the downstream trap and fish recaptured in the rapids. The uppermost part of the rapids (stretch 1) and the catch in the upstream trap was dominated by fish of riverine origin. Post-stocking migration was influenced by sex but not by body size. Females showed a greater propensity to stay in the rapids compared with males. Implications of the results for stocking grayling in natural streams and regulated rivers are discussed.