Soil structure and the saturated hydraulic conductivity of subsoils

The saturated hydraulic conductivity, K_sat, was measured on soil samples collected from the plough layer and the subsoil. A range of naturally occurring soil bulk densities was obtained by sampling in different years, with different crops and within and without wheel-tracks, etc. It was found that, for the plough layer, quite good linear relationships exist between the logarithm of K_sat and the bulk density. However, for the subsoils, the value of K_sat usually lies above the regression line for found for the corresponding plough layer. This “excess” hydraulic conductivity of subsoils is attributed to the presence of biopores, especially root channels. The lower hydraulic conductivity of the plough layer, relative to the subsoil, is attributed to the destruction of these biopores by tillage. A simple model for the separate contributions of soil texture and root channels to the overall value of K_sat is presented. It is concluded that subsoil tillage could cause significant reductions in K_sat with potentially serious environmental consequences unless it is repeated periodically.     

Evaluation of different methods for the prediction of saturated hydraulic conductivity in tilled and untilled soils

The larger the bulk density of the soil, the smaller the saturated hydraulic conductivity (K_s), however, the relationship between K_s and dry bulk density for tilled and untilled conditions is different. K_s is lower in tilled soil than in untilled soil with the same texture at the same bulk density. The purpose of this study was to compare different models for the prediction of K_s for two soil textures under both tilled and non-tilled conditions. We compred two models based on the non-similar media concept (NSMC-0, NSMC-1), a model based on the similar media concept (SMC) and a model based on the Kozeny equation and Poiseuille law for prediction of K_s (KC-1 and KC-2). This study was conducted at two areas with loam and silty clay loam soils under tilled and untilled conditions. It is concluded that the SMC model is not able to predict K_s under either tilled or untilled conditions. Further, the NSMC-0 model, along with an equation to estimate the shape factor, was able to predict K_s versus dry bulk density for tilled soils. According to our study, under untilled conditions, the KC-1 and NSMC-1 models, and under tilled conditions, the NSMC-1 and NSMC-0 models, predicted K_s accurately. It is concluded that the NSMC models together with the optimized Kozeny–Carman models could reliably be used to predict K_s in different soil textures.     

The structure of two alluvial soils in Italy after 10 years of conventional and minimum tillage

Micro and macroporosity, pore shape and size distribution, aggregate stability, saturated hydraulic conductivity and crop yield were analysed in alluvial silty loam (Fluventic Eutrochrept) and clay soils (Vertic Eutrochrept) following long-term minimum and conventional tillage. The soil structure attributes were evaluated by characterizing porosity by means of image analysis of soil thin sections prepared from undisturbed soil samples.

The interaggregate microporosity, measured by mercury intrusion porosimetry, increased in the minimally tilled soils, with a particular increase in the storage pores (0.5–50 μm). The amount of elongated transmission pores (50–500 μm) also increased in the minimally tilled soils. The resulting soil structure was more open and more homogeneous, thus allowing better water movement, as confirmed by the greater hydraulic conductivity of the minimally tilled soils. The aggregate stability was less in the conventionally tilled soils and this resulted in a greater tendency to form surface crusts and compacted structure, compared with the minimally tilled soils. The latter tillage practice seemed to maintain, in the long-term, better soil structure conditions and, therefore, maintain favourable conditions for plant growth. In the silt loam, the crop yield did not differ significantly between the two tillage systems, while in the clay soil it decreased in the minimum tilled soil because of problems of seed bed preparation at the higher surface layer water content.     

Comparative effects of annual and permanent dairy pastures on soil physical properties in the Tsitsikamma region of South Africa

Abstract. The effects of grazed, annual ryegrass pasture (annually tilled with a rotary cultivator) and permanent kikuyu pasture were compared with that of undisturbed native vegetation at four sites in the Tsitsikamma region, South Africa. Soil organic carbon content, aggregate stability, saturated hydraulic conductivity, air permeability, root length density and rooting depth were all less under ryegrass than kikuyu pasture. There was, however, no consistent effect of pasture-type on pore size distribution or penetrometer resistance. Differences in penetrometer resistance were most obvious in the 10–30 cm layer with subsurface compaction being evident at some sites under both types of pasture. This was attributed to the treading effects of grazing cattle plus formation of a compacted layer at the depth of tillage under ryegrass pastures. Subsoil tillage of a ryegrass pasture resulted in a substantial reduction in penetrometer resistance in the compacted 10–20 cm layer and increases in hydraulic conductivity, air permeability, root length density and rooting depth. We conclude that conversion from conventional to zero tillage is a potential way of improving the sustainability of annual pasture production and that the extent of subsoil compaction under both pasture types needs further investigation.     

Different responses in bulk density and saturated hydraulic conductivity to soil deformation by logging machinery on a Ferralsol under native forest

Ferralsols have high structural stability, although structural degradation has been observed to result from forest to tillage or pasture conversion. An experimental series of forest skidder passes in an east Amazonian natural forest was performed for testing the effects of mechanical stress during selective logging operations on a clay‐rich Ferralsol under both dry and wet soil conditions. Distinct ruts formed up to 25 cm depth only under wet conditions. After nine passes the initially very low surface bulk density of between 0.69 and 0.80 g cm^?3 increased to 1.05 g cm^?3 in the wet soil and 0.92 g cm^?3 in the dry soil. Saturated hydraulic conductivities, initially >250 mm h^?1, declined to a minimum of around 10 mm h^?1 in the wet soil after the first pass, and in the dry soil more gradually after nine passes. The contrasting response of bulk density and saturated hydraulic conductivity is explained by exposure of subsoil material at the base of the ruts where macrostructure rapidly deteriorated under wet conditions. We attribute the resultant moderately high hydraulic conductivities to the formation of stable microaggregates with fine sand to coarse silt textures. We conclude that the topsoil macrostructure of Ferralsols is subject to similar deterioration to that of Luvisols in temperate zones. The stable microstructure prevents marked compaction and decrease in hydraulic conductivity under wetter and more plastic soil conditions. However, typical tropical storms may regularly exceed the infiltration capacity of the deformed soils. In the deeper ruts water may concentrate and cause surface run‐off, even in gently sloping areas. To avoid soil erosion, logging operations in sloping areas should therefore be restricted to dry soil conditions when rut formation is minimal.     

Predicting unsaturated hydraulic conductivity of soil based on some basic soil properties

Soil hydraulic conductivity is a crucial parameter in modeling flow process in soils and deciding water management. In this study, by combining the non-similar media concept (NSMC) to the one-parameter model of Brooks and Corey, a new NSMC-based model for estimating unsaturated hydraulic conductivity of various soils was presented. The main inputs are soil bulk density, particle-size distribution, soil water retention characteristic and saturated hydraulic conductivity of soil. The results indicated that the NSMC-based model could generally more accurately predict unsaturated hydraulic conductivity of soils, as compared to four one-parameter models and van Genuchten–Mualem model. This study, by introducing NSMC, provided a new way to incorporate soil physical heterogeneity into soil hydraulic simulation, and hence NSMC-based approach is expected to improve efficiency of the existing models in the simulation of soil water flow.     

Tillage effects on near-surface soil hydraulic properties

The processes for the formation of porosity are thought to differ between tilled and non-tilled cropping systems. The pores are created primarily by the tillage tool in the tilled systems and by biological processes in non-tilled systems. Because of the different methods of pore formation, the pore size distribution, pore continuity and hydraulic conductivity functions would be expected to differ among tillage systems. The objective of this study was to determine effects of three tillage systems — mold-board plow (MP), chisel plow (CP), and no-till (NT) — on hydraulic properties of soils from eight long-term tillage and rotation experiments. Tillage effects on saturated and unsaturated hydraulic conductivity, pore size distribution, and moisture retention characteristics were more apparent for soils with a continuous corn (CC) rotation than for either a corn-soybean (CS) rotation or a corn-oats-alfalfa (COA) rotation. Pore size distributions were similar among tillage systems for each soil except for three soils with a CC rotation. The MP system increased volume of pores >150 μm radius by 23% to 91% compared with the NT system on two of the soils, but the NT system increased the volume of the same radius pore by 50% on one other soil. The NT system had 30 to 180% greater saturated hydraulic conductivity than either the CP or MP systems. The NT system with a CC rotation showed a greater slope of the log unsaturated hydraulic conductivity; log volumetric water content relationship on two of the soils indicating greater water movement through a few relatively large pores for this system than for either the CP or MP systems.     

Tillage force prediction from terrain characterization with the bevameter

The relationship between the soil parameters measured during soil testing using the bevameter system and horizontal forces acting on a simple tillage tool were investigated. Field experiments were conducted on untilled, compacted and recently tilled soil. On both soils, five sites were randomly chosen where bevameter and draft measurements were performed. The parameters measured were modulus of soil deformation, wet and dry bulk density, soil moisture content, tool operating depth, tool operating speed and horizontal draft.

A statistical analysis of data indicated that a mathematical model for predicting draft should include operating depth, dry bulk density and modulus of deformation.     

Runoff and soil erosion under rainfall simulation of Andisols from the Ecuadorian Páramo: effect of tillage and burning

In northern Ecuador, soils of high altitude grasslands (páramos) are mainly non-allophanic Andisols developed on Holocenic volcanic ash. These soils have a high water retention capacity and are the “water tank” of central Ecuador. To assess the effect of land use (burning and tillage) on soil hydrodynamic properties, rainfall simulation was conducted at two different sites. At Pichincha near Quito, the simulation was conducted on a recent volcanic ash soil comparing natural, tilled and burned plots. At El Angel, the simulation was conducted on a mature non-allophanic Andisol comparing natural, recently tilled and formerly cultivated plots.On natural plots, the infiltration rate was very high and sediment loss very low. Results for infiltration rate and runoff indicated that land use change on páramos increased runoff flow and reduced saturated hydraulic conductivity. Superficial reorganisation of the soil surfaces occurred on tilled plots at both sites. This crusting process was fast and resulted in surfaces with very low conductivity at Pichincha. The same processes seemed to be slower at El Angel. The soil surface of recent Andisols at Pichincha was prone to crusting whereas the mature Andisol, at El Angel, with a lower bulk density, was compacted when the kinetic energy of raindrops was high. Water repellency occurred after burning at Pichincha and following long natural air drying after tillage in the non-allophanic A horizon at El Angel. Water repellency combined with the low bulk density of soil aggregates explain the intensity of sediment losses in the abandoned soils after cultivation (Bare fallow plots). Erosion occurred in these areas through floating hydrophobic and stable aggregates.     

黄河三角洲滨海盐渍土饱和导水率的研究

通过对黄河三角洲滨海盐渍土饱和导水率的研究, 结果表明: 原状土的饱和导水率随着土壤剖面深度的增加呈现出表土层高、中间土层低、底土层又升高的趋势; 扰动土与原状土的饱和导水率差异较大, 土壤饱和导水率与土壤容重呈负相关、而与孔隙度、结构系数、团聚度等均呈正相关。原状土的饱和导水率能反映田间水分运动以及孔隙状况, 对研究土壤水量平衡和水土保持有重要的意义。扰动土的饱和导水率对于土壤理化性质的理论研究有一定参考价值。     

Prediction of saturated hydraulic conductivity of compacted soils using empirical scaling factors

A new empirical-based scaling method is introduced to predict saturated hydraulic conductivity (K _s ) of compacted soils. This method is an improvement of the former non-similar media concept (NSMC) model that is generalized for tilled and untilled conditions. In this method, geometric mean particle size diameter (d_g ), geometric standard deviation (σ _g ) and saturated soil water content (total porosity) are successfully incorporated in the empirical-based scaling factor of K _s . Results showed that the scaled model overestimated K _s by ～18%, whereas the NSMC model underestimated K _s by ～21%. However, the scaled model based on the similar media concept (SMC) failed to predict K _s . Because of the complexity and high uncertainty in determining the shape factor parameter in the NSMC model, it is suggested that the new scaled model might be used reliably in practical cases to predict K _s in the various layers of compacted soils irrespective of the tillage condition. Further assessment of the new scaling model in other areas, in which new collected data are available, is recommended.     

Impact of land‐use changes on soil hydraulic properties of Calcaric Regosols on the Loess Plateau,NW China

Vegetation restoration efforts (planting trees and grass) have been effective in controlling soil erosion on the Loess Plateau (NW China). Shifts in land cover result in modifications of soil properties. Yet, whether the hydraulic properties have also been improved by vegetation restoration is still not clear. The objective of this paper was to understand how vegetation restoration alters soil structure and related soil hydraulic properties such as permeability and soil water storage capacity. Three adjacent sites with similar soil texture, soil type, and topography, but different land cover (black locust forest, grassland, and cropland) were selected in a typical small catchment in the middle reaches of the Yellow River (Loess Plateau). Seasonal variation of soil hydraulic properties in topsoil and subsoil were examined. Our study revealed that land‐use type had a significant impact on field‐saturated, near‐saturated hydraulic conductivity, and soil water characteristics. Specifically, conversion from cropland to grass or forests promotes infiltration capacity as a result of increased saturated hydraulic conductivity, air capacity, and macroporosity. Moreover, conversion from cropland to forest tends to promote the creation of mesopores, which increase soil water‐storage capacity. Tillage of cropland created temporarily well‐structured topsoil but compacted subsoil as indicated by low subsoil saturated hydraulic conductivity, air capacity, and plant‐available water capacity. No impact of land cover conversion on unsaturated hydraulic conductivities at suction > 300 cm was found indicating that changes in land cover do not affect functional meso‐ and microporosity. Our work demonstrates that changes in soil hydraulic properties resulting from soil conservation efforts need to be considered when soil conservation measures shall be implemented in water‐limited regions. For ensuring the sustainability of such measures, the impact of soil conversion on water resources and hydrological processes needs to be further investigated.     

Effect of deep tillage for vineyard establishment on soil structure: A case study in Southern France

Deep tillage that is used before vine plantation to remove old vine roots and loosen subsoil may induce physical soil degradation that could affect soil structure and vine water supply. The objective of the study was to experimentally evaluate the effect of deep tillage on soil structure. The impacts on soil structure of two deep tillage techniques, i.e. deep ploughing and ripper, and two contrasted soil water conditions were compared in a experimental field by combining morphological observations, bulk density and saturated hydraulic conductivity measurements. These three methods were found very complementary to analyse and discriminate the impact of the different treatments. The proportion of compacted zones and mean bulk density increased from the initial plot (0.15 m² m⁻², 1.45 Mg m⁻³) to a maximum in the case of the deep ploughing under wet conditions plot (0.60 m² m⁻², 1.60 Mg m⁻³). The main results showed that (i) a significant soil compaction was observed after wet conditions only, (ii) deep ploughing produced more soil compaction than ripper because of a greater volume of soil affected by wheeling in the former operation and (iii) a specific response of soils is significatively observed in the case of deep ploughing only with an increase of compacted zones fragmentation in relation to a decrease of clay content.     

Long-term cultivation effects on hydraulic properties of a Walla Walla silt loam

Hydraulic properties of a Walla Walla silt loam were significantly changed by 50 years or more of cultivation under either a wheat-peas rotation (tillage depth 30 cm) or a wheat-summerfallow rotation (tillage depth 15 cm) as compared with no cultivation. Soil pH was reduced to depths as great as 60 cm in the cultivated sites; dry bulk density was increased to depths as great as 40 cm. Expressions of these changes were greater in the wheat-peas rotation because tillage was deeper than in the wheat-summerfallow rotation. Small reductions in soil organic matter were also noted in the cultivated sites. In the 60- to 90-cm depth, all three sites had similar bulk density, pH, cation exchange capacity, soil texture, desorption water characteristic, and hydraulic conductivity. In the upper 40-cm layer the desorption water characteristic showed that cultivation produced more smaller pores at the expense of large pores; in the upper 30-cm layer of the cultivated soils hydraulic conductivity was reduced at least 10-fold for water potentials > −100 cm of H₂O. Steady-state drainage profiles and associated assumptions suggest that long-term cultivation increased the hydraulic gradient in the upper 35 cm, and that the low saturated conductivity of the 0- to 15-cm layer had an overall drying effect on the 15- to 35-cm layer. In the cultivated soils increased runoff and denitrification in the plow layer should both be expected and water relations in the 15- to 35-cm layer should favor microorganisms sensitive to high water potentials. Simulations suggested that long-term cultivation decreased evaporation rates an estimated 40% and in wet soil, increased the drying time needed to attain optimum moisture for tillage.     

The effect of bulk density, water content and soil type on the diffusion of chloride in soil

The relative importance of soil bulk density, water content and potential on the self-diffusion and impedance factors of ³⁶C1 in a sandy loam and loamy clay were studied. The soil bulk densities used represented a range of conditions from freshly tilled seedbeds to compacted soils. The volumetric water contents and pF were the main factors controlling the soil impedance factors, with bulk density making a small but significant contribution.
Soil type affects the impedance factors through differences in anion exclusion volumes, the water contents of poorly connected pores that contribute little to the diffusion process, and tortuosity of the diffusion pathways.     

滩涂围垦农田土壤饱和导水率的影响因素及转换函数研究

确定苏北沿海滩涂围垦农田耕层土壤饱和导水率的影响因素,构建适合该区的土壤转换函数,是研究该区田间土壤水盐运动和盐渍化防控的重要前提。本文在该区典型地块实测土壤饱和导水率和相关土壤基本理化性质,探讨了该区土壤饱和导水率的剖面分布特点,对影响饱和导水率的土壤基本性质进行了主成分分析,并建立了用于该区饱和导水率间接估算的土壤转换函数。结果表明:滩涂围垦农田土壤饱和导水率随剖面深度增加呈表土层高、亚表层低、底土层又升高的趋势,20~40 cm土层饱和导水率最小,介于2.75~6.73 cm·d-1,属低透水强度;土壤容重随剖面深度增加表现出与饱和导水率相反的变化特点。除了容重、孔隙度、质地等物理因素外,土壤肥力、盐分等化学性质也是影响饱和导水率的重要因素;影响滩涂围垦农田土壤饱和导水率的因素可由持水特性、盐碱状况、养分特征和土壤质地4个主成分反映,其累计贡献率达78.17%。在Vereecken转换函数中引入土壤盐分后可提高预测精度,修正函数Vereecken_1是最适合滩涂围垦农区土壤、具有最佳预测精度的转换函数。本文构建的土壤转换函数,可通过较易获得的砂粒、黏粒、容重、盐分和有机质对耕层土壤饱和导水率进行较高精度的预测,其结果可为滩涂盐渍化农区田间尺度土壤饱和导水率间接估算以及水盐运动数值模拟提供支持。     

Modeling tillage effects on soil physical properties

Tillage refers to the manipulation of soil by an implement powered by humans, animals or machines. Tillage operation generally create two zones: (1) a zone where soil has been fractured and then turned over leading to rough surface conditions; and (2) a zone where soil has been compacted by the weight of the machinery. Thus, modeling tillage effects on soil physical properties involves two separate approaches depending upon the zone under consideration.

Modeling tillage systems offers an opportunity to: (1) synthesize the extensive experimental data in the literature; (2) develop tools for site specific management recommendations; and (3) identify areas of research where additional information is needed. Modeling tillage systems involves modeling the soil physical, chemical and biological properties and processes and then linking them with crop growth models to simulate crop yields or environmental impacts. This paper reviews models for predicting tillage effects on state soil physical properties. Specifically, we reviewed models which predict bulk density, surface microrelief, aerodynamic roughness length, water retention characteristics, hydraulic conductivity function, thermal conductivity, volumetric heat capacity and gas diffusion coefficient. Since most of the existing models for predicting soil physical properties are developed for untilled soils, the paper outlines procedures to adapt these models to fractured and compacted zones in tilled soils. The paper also identifies specific assumptions that need both laboratory and field testing.     

坡面尺度土壤特性的空间变异性

通过对20m长坡面土壤特性空间变异性的经典统计学分析,结果表明:(1)在同一土壤剖面内,各级粒径含量呈弱变异性,而有机质含量随土层深度的增大而逐渐降低,呈中等变异性;(2)土壤干容重的空间变异性较小,呈弱变异性,但土壤饱和导水率的空间变异性较大,呈中等变异性;(3)水分特征曲线具有一定的空间变异性,比水容量空间变异性较大,呈中等变异性。坡面土壤饱和导水率和干容重的等值线图表明,土壤饱和导水率的变化趋势并不仅仅取决于土壤干容重的相对大小,可能与有机质含量、黏粒含量以及根系分布情况等也有一定的关系。     

耕作与覆盖措施对黄土塬区春玉米田土壤水气传输的影响

  【目的】  良好的土壤物理和水力学性质是土壤肥力可持续的基础。研究黄土高原旱作农业区长期不同耕作、覆盖措施对土壤水气传输性质的影响,为黄土塬区可持续的农田管理提供参考。  【方法】  基于设在渭北旱塬始于2002年的田间定位试验,选取传统耕作 (CT)、传统耕作+秸秆覆盖 (TS)、传统耕作+地膜覆盖 (TP)、传统耕作+全膜覆盖 (TWP)、免耕 (NT)、免耕+秸秆覆盖 (NS)、免耕+地膜覆盖 (NP)、免耕+生草覆盖 (NG) 共8个处理。于2019年春玉米收获期采集剖面土样,对0—10、10—20、20—30和30—40 cm土层土壤质量含水量、容重、导气率、相对气体扩散率和饱和导水率进行测定与分析。  【结果】  与CT处理相比,TS处理显著增加了0—40 cm土壤平均质量含水量,降低了0—40 cm各层土壤导气率,增加了各层土壤相对气体扩散率,表层 (0—10 cm) 土壤饱和导水率显著降低了75.9%;TP处理收获期耕层 (0—20 cm) 土壤容重增加,土壤总孔隙度显著降低,在0—10 cm土层,土壤导气率显著提高了54.1%;TWP处理耕层土壤容重显著增加,土壤总孔隙度显著降低,剖面0—40 cm土壤导气率和饱和导水率分别平均增加了64.8%和111.2%,尤其是表层土壤导气率显著提高了99.5%。与NT处理相比,NS处理耕层土壤容重降低,总孔隙度增加,表层土壤质量含水量、相对气体扩散率和饱和导水率分别显著提高了14.8%、25.3%和446.4%;NP处理耕层土壤容重增加,总孔隙度降低,表层土壤质量含水量和饱和导水率分别显著增加3.5%和145.2%,土壤导气率显著降低33.7%;NG处理耕层土壤容重降低,总孔隙度增加,表层土壤质量含水量显著提高了11.3%,土壤相对气体扩散率显著降低了42.1%。相同覆盖条件下与传统耕作比较,免耕处理能够降低下层20—40 cm土壤容重,增加土壤总孔隙度,提高土壤持水性,虽然降低了表层0—10 cm土壤导气率,但提高了土壤相对气体扩散率和饱和导水率。  【结论】  免耕秸秆覆盖可降低耕层土壤容重,增加总孔隙度,并且显著提高耕层土壤相对气体扩散率和饱和导水率,增加下层土壤导气率,是免耕处理组中最佳处理。传统耕作全膜覆盖可提高耕层土壤导气率、相对气体扩散率和饱和导水率,是传统耕作组中最佳处理,可有效保持渭北旱塬良好的土壤水气传输能力。     

灰色关联及非线性规划法构建传递函数估算黑土水力参数

土壤水分特征曲线和饱和导水率是重要的水力参数,为了简便准确获取这些参数,以松嫩平原黑土区南部为研究区域,采集136个采样点土样用于测定不同土层土壤水分特征曲线、饱和导水率以及土壤理化性质,并运用灰色关联分析确定影响土壤水力参数的主要土壤理化性质,采用非线性规划构建土壤分形维数、有机质、干容重、土壤颗粒组成与土壤水分特征曲线、饱和导水率之间的土壤传递函数,并通过与现有土壤传递函数对比分析进行精度验证。结果表明:1)土壤分形维数是估算土壤水分特征曲线模型参数和饱和导水率的主要参数之一,同时,干容重和有机质含量也在不同土层土壤传递函数中起到重要的作用;2)通过验证分析,不同土层各参数平均绝对误差接近于0,均方根误差值也都较小,其中在不同土层土壤传递函数估算的土壤含水率均方根误差分别为0.022、0.017cm~3/cm~3;3)对比分析其他已存的土壤水分特征曲线和饱和导水率的土壤传递函数,该文构建的土壤传递函数均方根误差值均较小,决定系数值都在0.66以上,表明估算精度较高,均好于其他方法估算精度,具有良好的区域适应性。综上,所构建的土壤水分特征曲线和饱和导水率土壤传递函数可以用于松嫩平原黑土区土壤水力参数估算。