Assessment of spatial variability in nitrate leaching to reduce nitrogen fertilizers impact on water quality

Nitrogen leaching has caused a growing societal concern over N fertilizer impact on water quality. One way to decrease nitrogen loss through leaching is to adjust fertilizer inputs to site-specific conditions. This study was conducted to investigate spatial variability of NO₃ leaching parameters on a 5 ha commercial wheat field (Typic Ustifluent) located 25 km north of Tokat, Turkey, for the purpose of dividing the field into small cells in which application rates can be kept constant. NO₃ leaching parameters were calculated using the monthly analysis version of computer program NLEAP (nitrate leach and economic analysis package) on a regular grid spacing of 25 m, and semi-variogram for each parameter was calculated using the computer program GEAOES. The values for parameter NL (nitrate leached) were between 24.64 (low) and 77.28 kg ha⁻¹ (medium), for NAL (nitrate available for leaching) 42.46 (low) and 274.40 kg ha⁻¹ (high), and for MRI (movement risk index) 0.28 (low) and 0.35 (medium). Values for parameter ALRP (annual leaching risk potential) varied from high (index=4) to moderate (index=3). A moderately significant correlation (r=0.54, P<0.01) was found between measured and model-estimated values for the parameter NAL, indicating that the NLEAP model adequately simulated the NO₃ leaching in the study area. Values for range were 360 m for NAL, 350 m for NL and 180 m for MRI, and nugget effect was 0.72 for MRI, 0.45 for NAL and 0.25 for NL, and mean correlation distances (MCD) were 145 m for NAL and 61 m for NL. Although, the spatial patterns for the parameters NAL and NL were similar, the upper cell limit for parameter NAL was higher than two times that of parameter NL, suggesting that calculation of input for continuous control of nitrogen application rate in a variable rate nitrogen fertilizer application program be based on the spatial pattern of NL but not on that of NAL.     

Water and nitrate movement in drip-irrigated onion under fertigation and irrigation treatments

Frequent fertigation of crops is often advocated in the technical and popular literature, but there is limited evidence of the benefits of high-frequency fertigation. Field experiments were conducted on an Indo-American Hybrid var., Creole Red, of onion crop during three winter seasons of 1999–2000 through 2001–2002 in coarse-textured soil of Delhi under the semi-arid region of India. Three irrigation levels of 60, 80 and 100% of the crop evapotranspiration (ET) and four fertigation frequencies of daily, alternate day, weekly and monthly comprised the fertigation treatment. Analysis of soil samples indicated considerable influence of fertigation frequency on NO₃-N distribution in soil profile. NO₃-N in lower soil profiles (30.0–60.0 cm soil depth) was marginally affected in daily, alternate day and weekly fertigation. However, fluctuations of NO₃-N content in 0.0–15.0, 15.0–30.0, 30.0–45.0 and 45.0–60.0 cm soil depth was more in monthly fertigation frequency. The level of soil NO₃-N after the crop season shows that more NO₃-N leached through the soil profile in monthly fertigation frequency. Amounts of irrigation water applied in three irrigation treatments proved to be too small to cause significant differences in the content of NO₃-N leached beyond rooting depth of onion. Yield of onion was not significantly affected in daily, alternate day and weekly fertigation, though there was a trend of lower yields with monthly fertigation. The highest yield was recorded in daily fertigation (28.74 t ha⁻¹) followed by alternate day fertigation (28.4 t ha⁻¹). Lowest yield was recorded in monthly fertigation frequency (21.4 t ha⁻¹). Application of 56.4 cm irrigation water and 3.4 kg ha⁻¹ urea per fertigation (daily) resulted in highest yield of onion with less leaching of NO₃-N.     

Soil N and salinity leaching after the autumn irrigation and its impact on groundwater in Hetao Irrigation District,China

Soil water and salinity are crucial factors influencing crop production in arid regions. An autumn irrigation system employing the application of a large volume of water (2200–2600 m³ ha⁻¹) is being developed in the Hetao Irrigation District of China, since the 1980s with the goal to reduce salinity levels in the root zone and increase the water availability for the following spring crops. However, the autumn irrigation can cause significant quantities of NO₃⁻ to leach from the plant root zone into the groundwater. In this study, we investigated the changes in soil water content, NO₃–N and salinity within a 150 cm deep soil profile in four different types of farmlands: spring wheat (F_W), maize (F_M), spring wheat–maize inter-planting (F_W–M) and sunflower (F_S). Our results showed that (1) salt losses mainly occurred in the upper 60 cm of the soil and in the upper 40 cm for NO₃–N; (2) the highest losses of salt and NO₃–N could be observed in F_W, whereas the lowest losses were found in F_W–M.NO₃–N concentration, pH and electrical conductivity (EC) in the groundwater were also monitored before and after the autumn irrigation. We found that the autumn irrigation caused the groundwater concentration of NO₃–N to increase from 1.73 to 21.6 mg L⁻¹, thereby, exceeding the standards of the World Health Organization (WHO). Our results suggest that extensive development of inter-planting tillage might be a viable measure to reduce groundwater pollution, and that the application of optimized minimum amounts of water and nitrogen to meet realistic yield goals, as well as the timely application of N fertilizers and the use of slow release fertilizers can be viable measures to minimize nitrate leaching.     

Potential nitrate losses under different agricultural practices in the pampas region,Argentina

Fertilization is an important cause of groundwater contamination with nitrate in agricultural soils. The objectives of the present work were: (i) to quantify the nitrate leaching in two fertilized and irrigated soils of the Pampas Region, Argentina; (ii) to test the ability of the NLEAP model to predict residual and leached nitrate in those soils. The soils were a Typic Hapludoll and a Typic Argiudoll. The treatments were: natural grassland never ploughed or fertilized; maize with a short history of fertilization; maize with a long history of fertilization; irrigated maize with a long history of fertilization. Both sites were sampled after harvest in two consecutive years to a 3 m depth. Residual nitrate and potential losses below 150 cm were estimated by NLEAP model. The average amount of nitrate (NO₃-N), including values of all treatments, in the upper layer (0–1.5 m) was 128 kg NO₃-N ha⁻¹ in the first sampling date and was consistently lower in the second sampling date (38 kg NO₃-N ha⁻¹). In the deeper layer (1.5–3 m) these values were 80 and 28 kg NO₃-N ha⁻¹ for the first and second sampling date, respectively. Differences between the non-fertilized and the fertilized treatments were significantly smaller in the second sampling date. Obtained results suggest that the rainfall previous to the first sampling was not enough to displace nitrate below 3 m depth. The afterwards heavy rainfall leached nitrate previously accumulated in the soil. Complementary irrigation did not affect nitrate movements. Simulated residual and leached nitrate showed a high correlation with observed values. Nitrate leaching was more associated to rainfall regime and crop yields than to soil type. Simulated residual and leached nitrate showed a high correlation with measured values in both soils, which suggests that NLEAP was appropriate to predict soil nitrate leaching under the studied conditions.     

Trickle and sprinkler irrigation of potato (Solanum tuberosum L.) in the Middle Anatolian Region in Turkey

The potato (Solanum tuberosum L.) is widely planted in the Middle Anatolian Region, especially in the Nigde-Nevsehir district where 25% of the total potato growing area is located and produces 44% of the total yield. In recent years, the farmers in the Nigde-Nevsehir district have been applying high amounts of nitrogen (N) fertilizers (sometimes more than 900 kg N ha⁻¹) and frequent irrigation at high rates in order to get a much higher yield. This situation results in increased irrigation and fertilization costs as well as polluted ground water resources and soil. Thus, it is critical to know the water and nitrogen requirements of the crop, as well as how to improve irrigation efficiency. Field experiments were conducted in the Nigde-Nevsehir (arid) region on a Fluvents (Entisols) soil to determine water and nitrogen requirements of potato crops under sprinkler and trickle irrigation methods. Irrigation treatments were based on Class A pan evaporation and nitrogen levels were formed with different nitrogen concentrations.The highest yield, averaging 47,505 kg ha⁻¹, was measured in sprinkler-irrigated plots at the 60 g m⁻³ nitrogen concentration level in the irrigation treatment with limited irrigation (480 mm). Statistically higher tuber yields were obtained at the 45 and 60 g m⁻³ nitrogen concentration levels in irrigation treatments with full and limited irrigation. Maximum yields were obtained with about 17% less water in the sprinkler method as compared to the trickle method (not statistically significant). On the loam and sandy loam soils, tuber yields were reduced by deficit irrigation corresponding to 70% and 74% of evapotranspiration in sprinkler and trickle irrigations, respectively. Water use of the potato crop ranged from 490 to 760 mm for sprinkler-irrigated plots and 565–830 mm for trickle-irrigated treatments. The highest water use efficiency (WUE) levels of 7.37 and 4.79 kg m⁻³ were obtained in sprinkle and trickle irrigated plots, respectively. There were inverse effects of irrigation and nitrogen levels on the WUE of the potato crops. Significant linear relationships were found between tuber yield and water use for both irrigation methods. Yield response factors were calculated at 1.05 for sprinkler methods and 0.68 for trickle methods. There were statistically significant linear and polynomial relationships between tuber yield and nitrogen amounts used in trickle and sprinkler-irrigated treatments, respectively. In sprinkler-irrigated treatments, the maximum tuber yield was obtained with 199 kg N ha⁻¹. The tuber cumulative nitrogen use efficiency (NUE_cu) and incremental nitrogen use efficiency (NUE_in) were affected quite differently by water, nitrogen levels and years. NUE_cu varied from 16 to 472 g kg⁻¹ and NUE_in varied from 75 to 1035 g kg⁻¹ depending on the irrigation method. In both years, the NH₄-N concentrations were lower than NO₃-N, and thus the removed nitrogen and nitrogen losses were found to be 19–87 kg ha⁻¹ for sprinkler methods and 25–89 kg ha⁻¹ for trickle methods. Nitrogen losses in sprinkler methods reached 76%, which were higher than losses in trickle methods.     

Spatial and temporal distributions of nitrogen and crop yield as affected by nonuniformity of sprinkler fertigation

Deep percolation and nitrate leaching are important considerations in the design of sprinkler systems. Field experiments were therefore conducted to investigate the influence of nonuniformity of sprinkler irrigation on deep percolation and spatial distributions of nitrogen and crop yield during the growing season of winter wheat at an experiment station in Beijing, China. Three experimental plots of a sandy clay loam soil in the 0–40 cm depth interval and a loamy clay soil below 40 cm were irrigated with a sprinkler irrigation system that had a seasonal averaged Christiansen irrigation uniformity coefficient (CU) varying from 72 to 84%. Except for the fertilizer applied before planting, fertilizer was applied with the sprinkler irrigation system. The corresponding seasonal averaged CU for fertigation varied from 71 to 85%. Daily observation of matrix water potentials in the root zone showed that little deep percolation occurred. Consequently, the effect of sprinkler uniformity on deep percolation was minor during the irrigation season for the soil tested. Intensive gravimetric soil core samplings were conducted several times during the irrigation season in a grid of 5 m × 5 m for each plot to determine the spatial and temporal variation of NH₄-N and NO₃-N contents. Soil NH₄-N and NO₃-N exhibited high spatial variability in depth and time during the irrigation season with CU values ranging from 23 to 97% and the coefficient of variation ranging from 0.04 to 1.06. A higher uniformity of sprinkler fertigation produced a more uniform distribution of NH₄-N, but the distribution of NO₃-N was not related to fertigation. Rather it was related to the spatial variability of NO₃-N before fertigation began. At harvest, the distribution of dry matter above ground, nitrogen uptake, and yield were measured and the results indicated that sprinkler fertigation uniformity had insignificant effects on the parameters mentioned above. Field experimental results obtained from this study suggest that sprinkler irrigation if properly managed can be used as an efficient and environment-friendly method of applying water and fertilizers.     

Groundwater quality in CR-V irrigation district (Bardenas I,Spain): Alternative scenarios to reduce off-site salt and nitrate contamination

Irrigated agriculture may negatively affect groundwater quality and increase off-site salt and nitrate contamination. Management alternatives aimed at reducing these potential problems were analysed in the 15498 ha CR-V Irrigation District (Spain) by monitoring 49 wells and modelling the hydrological regime in a representative well of the Miralbueno Aquifer. Groundwaters presented low to moderate electrical conductivity (EC) (mean = 0.89 dS/m) and high [NO₃⁻] (mean = 94 mg/L). The groundwater depth (GWD) during the 2001 hydrological year responded to the annual cycles of precipitation and irrigation as well as to the secondary cycles derived from irrigation scheduling. GWD were consistently simulated by the groundwater BAS-A model. Model results indicate that an increase in irrigation efficiency and the pumping of groundwater for irrigation will decrease GWD and aquifer's discharge by 56–70%, depending on scenarios. These recommendations will save good-quality water in the reservoir, will be beneficially economical to farmers, and will minimize off-site salt and nitrogen contamination.     

Optimal applied water and nitrogen for corn

Water and fertilizer applications should be limited due to scarce resources and environmental protection aspects. An analysis of crop yield production and profit maximization was conducted to determine the optimal water and nitrogen allocation. In this analysis based on crop production and cost functions, a series of equations for determination of applied water and nitrogen for three conditions of maximum yield (w_m and N_m, respectively), maximum profit under limited land (w_l and N_l, respectively) and maximum profit under limited water (w_w and N_w, respectively) were derived. The associated crop production function was determined from the results of a corn experiment with four levels of nitrogen fertilization and varying amounts of applied water via a line source of sprinkler irrigation. The previously derived equations were also applied to the experimental field data and finally the optimum amounts of applied water and nitrogen were determined at different conditions (w_m, w_l, and w_w for water and N_m, N_l, and N_w for nitrogen, respectively). At present market value (15.55 Rls/m³ for water and 652 Rls/kg for nitrogen) the amounts of w_m, w_l, and w_w were 1.0, 0.99, and 0.74 m, respectively, and the amounts of N_m, N_l, and N_w were 212, 212, and 206 kg N/ha, respectively. Because of the low price of nitrogen, the optimum amounts of nitrogen at three mentioned conditions were similar. But if the price of nitrogen and water are increased (i.e. 50000 Rls/kg N and 100 Rls/m³ water), then the amounts of applied nitrogen and water at the mentioned three conditions would be 212, 67, and 61 kg N/ha, and 1.00, 0.93, 0.84 m, respectively. When water is limiting, the optimum amount of applied water would not be different by changing the water price, however, it may be increased by a little amount when the nitrogen price is increased.     

Water use and lint yield response of drip irrigated cotton to the length of irrigation season

A 2-year experiment was conducted at Tal Amara Research Station in the Bekaa Valley of Lebanon to determine water use and lint yield response to the length of irrigation season of drip irrigated cotton (Gossypium hirsutum L.). Crop evapotranspiration (ET_crop) and reference evapotranspiration (ET_rye-grass) were directly measured at weekly basis during the 2001 growing period using crop and rye-grass drainage lysimeters. Crop coefficients (K_c) in the different growth stages were calculated as ET_crop/ET_rye-grass. Then, the calculated K_c values were used in the 2002 growing period to estimate evapotranspiration of cotton using the FAO method by multiplying the calculated K_c values by ET_rye-grass measured in 2002. The length of irrigation season was determined by terminating irrigation permanently at first open boll (S1), at early boll loading (S2), and at mid boll loading (S3). The three treatments were compared to a well-watered control (C) throughout the growing period. Lint yield was defined as a function of components including plant height at harvest, number of bolls per plant, and percentage of opened bolls per plant.Lysimeter-measured crop evapotranspiration (ET_crop) totaled 642 mm in 2001 for a total growing period of 134 days, while when estimated with the FAO method in 2002 it averaged 669 mm for a total growing period of 141 days from sowing to mature bolls. Average K_c values varied from 0.58 at initial growth stages (sowing to squaring), to 1.10 at mid growth stages (first bloom to first open boll), and 0.83 at late growth stages (early boll loading to mature bolls).Results showed that cotton lint yields were reduced as irrigation amounts increased. Average across years, the S1 treatment produced the highest yield of 639 kg ha⁻¹ from total irrigations of 549 mm, compared to the S2 and S3 treatments, which yielded 577 and 547 kg ha⁻¹ from total irrigations of 633 and 692 mm, respectively, while the control resulted in 457 kg ha⁻¹ of lint yield from 738 mm of irrigation water. Water use efficiency (WUE) was found to be higher in S1 treatment and averaged 1.3 kg ha⁻¹ mm⁻¹, followed by S2 (1.1 kg ha⁻¹ mm⁻¹), and S3 (1.0 kg ha⁻¹ mm⁻¹), while in the control WUE was 0.80 kg ha⁻¹ mm⁻¹. Lint yield was negatively correlated with plant height and the number of bolls per plant and positively correlated with the percentage of opened bolls. This study suggests that terminating irrigation at first open boll stage has been found to provide the highest cotton yield with maximum WUE under the semi-arid conditions of the Bekaa Valley of Lebanon.     

Evapotranspiration and seed yield of field grown soybean under deficit irrigation conditions

Evapotranspiration was measured for a reference crop, rye grass (Lolium prerenne) and soybean (Glycine max L. Merril) grown over two seasons in 2000 and 2001 at Tal Amara Research Station, Lebanon, using drainage and weighing lysimeters. Climatic data from the field weather station were recorded daily. Within the experimental plots, irrigation was withheld at full bloom, R2 stage (S1 treatment), at seed enlargement, R5 stage (S2 treatment) and at mature seeds, R7 stage (S3 treatment). Further, a control (C) was fully-irrigated throughout the growing period.Average crop evapotranspiration (ETc) as measured by the drainage lysimeters in 2000 totaled 800 mm for a total growing period of 140 days. However, when ETc was measured by the weighing lysimeter in 2001, it was 725 mm during a growing period of 138 days. Average crop coefficients (K_c) were computed for different growth stages for the two growing periods by dividing the measured crop evapotranspiration (ETc) by the corresponding measured reference evapotranspiration (ETo-rye grass). K_c values ranged from 0.62 at V10 stage (10th node on the main stem beginning with the unifoliolate node) to 1.0 at pod initiation, then to 0.81 at mature pods.Growth parameters, leaf area index (LAI) and dry matter accumulation, have been shown to be sensitive to water stress caused by the deficit irrigations. However, growth parameters were found to compensate for water stress at early stages, while at seed maturity the compensation ability was decreased.Plants of the lysimeters produced average aboveground biomass and seed yield of 8.1 and 3.5 t ha⁻¹, respectively. However, in the well-irrigated field treatment, aboveground biomass and seed yield averaged 7.3 and 3.2 t ha⁻¹, respectively. Deficit irrigation at R2 stage reduced aboveground biomass and seed yield by 16 and 4%, respectively, while deficit irrigation at R5 stage reduced these two parameters by 6 and 28%, respectively, with comparison to the control. The significant decrease in biomass at R2 stage due to water deficit may be attributed to a pronounced reduction in the number of vegetative nodes. However, limited irrigation at this stage did not reduce significantly (P < 0.01) neither seed number nor seed weight, while at R5 stage these two parameters were reduced by 20 and 10%, respectively, with comparison to the control. Results showed also that deficit irrigation at R7 stage (S3) was more profitable than irrigation deficit at any other crop phenology and did not cause significant reductions either in seed number or seed weight.     

Spatial variability of solutes in a pecan orchard surface-irrigated with untreated effluents in the upper Rio Grande River basin

Untreated effluents are blended with water from the Rio Grande River and used for irrigation in the Juarez Valley of northern Mexico. Effluents are a source of nutrients, but may also be a source of heavy metal contamination. This study was conducted to characterize deposition patterns of selected metals, salts, and total nitrogen in a 6 ha pecan (Carya illinoenisis K.) orchard which had healthy-to-stunted trees with dieback. Orchard soil was collected along multiple transects to depths of 1.2 m, with spacing every 20 m. All solutes showed a magnitude variability in particular ions. Chromium, Ni, Pb, and Cd concentrations averaged <14 mg kg⁻¹. Soil Na, Ca, K, Mg, SO₄, Cl and NO₃–N averaged <100 mg kg⁻¹. Total N was <0.21%. Most solutes accumulated at the soil surface with the exception of Na and SO₄. Linear semi-variograms best described spatial metal deposition and surface clay content with a range of influence >189 m. Spherical semi-variograms best described spatial distribution of salts and total N, but accounted <50% of the variability. The solubility of solutes in moderately alkaline irrigation water and their specific behavior in calcareous soils likely affected deposition patterns. Estimated metal loads from irrigation over a 15-year period were <3 kg ha⁻¹, but about 187 Mg ha⁻¹ for total dissolved solids (salts). Pecan leaf tissue showed no signs of heavy metal accumulation. Suboptimum pecan growth was associated with salt accumulation in a clayey area with low permeability. Salts, in particular Na, rather than metals may be the most important inorganic contaminants for irrigated agriculture in this region. Salt loads in irrigation waters are expected to increase as agriculture increasingly relies on urban effluents too expensive to convert to potable water.     

Nitrate contamination of a rural aquifer and accumulation in the unsaturated zone

Groundwater contamination was studied in a rural setting of the Upper Pantanoso Stream Basin (UPSB) in the southeast of Buenos Aires Province, Argentina, where potential contaminant sources include inorganic fertilizer. Nitrate–N concentrations, greater than accepted level for safe drinking-water of 10 mg l⁻¹ were present in 36% of sampled wells and 67% of samples had nitrate concentrations exceeding the background level of 5 mg l⁻¹. Temporal fluctuation of nitrate concentrations in the groundwater was attributed to seasonal fluctuations in recharge and plant growth. Nitrate concentration was measured in deep soil profiles to determine the extent of leaching. Nitrate accumulation in the unsaturated zone of a soil cropped with potatoes was three times higher than the baseline N concentration found in the pasture. The greatest nitrate concentration in the soil profile occurred under irrigated corn where excessive nitrogen was applied. These results show that high fertilization rates and irrigation lead to increased hazards of groundwater pollution.     

Development and evaluation of integrated water and nitrogen model for maize

Maize (Zea mays L.) is an important food crop for irrigated regions in the world. Its growth and production may be estimated by different crop models in which various relationships between growth and environmental parameters are used. For simulation of maize growth and grain yield, a simulation model was developed (Maize Simulation Model, MSM). Dynamic flow of water, nitrogen (N) movement, and heat flow through the soil were simulated in unsteady state conditions by numerical analysis in soil depth of 0–1.8 m. Hourly potential evapotranspiration [ET_p(t)] for maize field was estimated directly by Penman–Monteith method. Hourly potential evaporation [E_p(t)] was estimated based on ET_p(t) and canopy shadow projection. Actual evaporation of soil surface was estimated based on its potential value, relative humidity of air, water pressure head and temperature at soil surface layer. Actual transpiration (T_a(t)) was estimated based on soil water content and root distribution at each soil layer. Hourly N uptake by plant was simulated by N mass flow and diffusion processes. Hourly top dry matter production (HDMA^j + 1, where j is number of hours after planting) was estimated by hourly corrected intercepted radiation (RSLT^j + 1) by plant leaves [determined from leaf area index (LAI^j + 1)] with air temperature, the maximum and minimum plant top N concentration and the amounts of nitrogen uptake. The value of LAI^j + 1 at each hour was estimated by the accumulated top dry matter production at previous hour using an empirical equation. Maize grain yield was estimated by a relationship between harvest index and seasonal plant top dry matter production. The model was calibrated using data obtained under field conditions by a line source sprinkler irrigation. When the values of water and nitrogen application were optimum, grain yield (moisture content of 15.5%) was 16.2 Mg ha⁻¹. Model was validated using two independent experimental data obtained from other experiments in the Badjgah (Fars province). The experimental results validated the proposed simulation model fairly well.     

Effect of initial soil salinity and subirrigation water salinity on potato tuber yield and size

A field lysimeter study was conducted to investigate the effect of initial soil salinity and salinity level of brackish subirrigation water on tuber weight and tuber size of three potato (Solanum tuberosum L.) cultivars (Kennebec, Norland and Russet Burbank) under simulated arid conditions. Both saline and non-saline initial soil conditions were simulated in a total of 36 lysimeters. Eighteen lysimeters were flushed with fresh water (0.2 dS/m), while the remaining 18 lysimeters were flushed with brackish water (2 dS/m). For each soil condition, two subirrigation water concentrations, 1 and 9 dS/m, were used in nine lysimeters each. For each subirrigation water treatment, three potato cultivars were grown. In all lysimeters, water table was maintained at 0.4 m from the soil surface. Arid conditions were simulated by covering the lysimeter top with plastic mulch, allowing the potato shoots to grow through a cut in the mulch. The average root zone salinities (EC_w) were found to be 1.2 and 1.5 dS/m in non-saline lysimeters subirrigated with 1 and 9 dS/m waters, respectively. The corresponding salinities were 3.2 and 3.7 dS/m in the saline lysimeters. Across cultivars, there was no significant effect of either initial soil salinity or subirrigation water salinity on total tuber weight. However, the weight of Grade A tubers was higher in non-saline soil than in saline soil. Kennebec and Russet Burbank Grade A tuber weights were not affected by the initial soil salinity. On the contrary, a significant reduction in Grade A and total tuber weight under initially saline soil was evident for the Norland cultivar.     

Nitrogen loss through subsurface drainage effluent in coastal rice field from India

Experiments were conducted to estimate nitrogen loss through drainage effluent in subsurface drained farmers’ field at a coastal site near Machilipatnam, Andhra Pradesh, India. The concentration of three forms of nitrogen, namely, NH₄–N, NO₂–N and NO₃–N in the subsurface drainage effluent from 15, 35 and 55 m drain spacing areas were measured in 1999 and 2000. The area with 15 m spacing was already reclaimed during 1986–1998 by the subsurface drainage system. The soil salinity of the root zone was brought down from an initial high of 35 to 4 dS m⁻¹. The subsurface drainage system with 35 and 55 m drain spacing was laid in the adjoining area and commissioned in 1998. Earlier raising of any crop in the area with 35 and 55 m spacings was not possible due to very high salinity, sodicity and poor drainage conditions. The nitrate-nitrogen loss dominated in reclaimed land with 15 m spacing whereas ammonium-nitrogen loss dominated in the land that was highly saline and in the initial stage of reclamation by the subsurface drainage technology with 35 and 55 m drain spacing. The total nitrogen loss of 3.75 kg per ha per year in 15 m drain spacing area was minimum and 23.53 kg per ha per year in 35 m drain spacing area was maximum. The nitrate-nitrogen loss contributed the maximum of 82% and ammonium- and nitrite-nitrogen contributed 11 and 7%, respectively, in 15 m drain spacing area whereas the ammonium losses contributed 93 and 82% in 35 and 55 m drain spacing areas, respectively. The losses in the form of nitrite and nitrate remained negligible in 35 m drain spacing area, but the losses to the tune of 8 and 15% in the form of nitrite and nitrate, respectively, occurred in 55 m drain spacing area.     

Latent heat flux over a furrow-irrigated tomato crop using Penman–Monteith equation with a variable surface canopy resistance

The Penman–Monteith (P–M) model with a variable surface canopy resistance (r_c) was evaluated to estimate latent heat flux (LE) or crop evapotranspiration (ET) over a furrow-irrigated tomato crop under different soil water status and atmospheric conditions. The hourly values of r_c were computed as a function of environmental variables (air temperature, vapor pressure deficit, net radiation, and soil heat flux) and a normalized soil water factor (F), which varies between 0 (wilting point, θ_WP) and 1 (field capacity, θ_FC). The Food and Agricultural Organization (FAO-56) method was also evaluated to calculate daily ET based on the reference evapotranspiration, crop coefficient and water stress coefficient. The performance of the P–M model and FAO-56 method were evaluated using LE values obtained from the Bowen ratio system. On a 20 min time interval, the P–M model estimated daytime variation of LE with a standard error of the estimate (SEE) of 46 Wm⁻² and an absolute relative error (ARE) of 3.6%. Thus, daily performance of the P–M model was good under soil water content ranging from 118 to 83 mm (θ_FC and θ_WP being 125 and 69 mm, respectively) and LAI ranging from 1.3 to 3.0. For this validation period, the calculated values of r_c and F ranged between 20 and 114 s m⁻¹ and between 0.87 and 0.25, respectively. In this case, the P–M model was able to predict daily ET with a SEE of 0.44 mm h⁻¹ (1.1 MJ m⁻² d⁻¹) and an ARE of 3.9%. Furthermore, the FAO-PM model computed daily ET with SEE and ARE values of 1.1 mm h⁻¹ (2.8 MJ m⁻² d⁻¹) and 5.2%, respectively.     

Effect of shallow groundwater table on crop water requirements and crop yields

Due to the increasing demand for food and fiber by its ever-increasing population, the pressure on fresh water resources of Pakistan is increasing. Optimum utilization of surface and groundwater resources has become extremely important to fill the gap between water demand and supply. At Lahore, Pakistan 18 lysimeters, each 3.05 m × 3.05 m × 6.1 m deep were constructed to investigate the effect of shallow water tables on crop water requirements. The lysimeters were connected to bottles with Marriotte siphons to maintain the water tables at the desired levels and tensiometers were installed to measure soil water potential. The crops studied included wheat, sugarcane, maize, sorghum, berseem and sunflower. The results of these studies showed that the contribution of groundwater in meeting the crop water requirements varied with the water-table depth. With the water table at 0.5 m depth, wheat met its entire water requirement from the groundwater and sunflower absorbed more than 80% of its required water from groundwater. Maize and sorghum were found to be waterlogging sensitive crops whose yields were reduced with higher water table. However, maximum sugarcane yield was obtained with the water table at or below 2.0 m depth. Generally, the water-table depth of 1.5–2.0 m was found to be optimum for all the crops studied. In areas where the water table is shallow, the present system of irrigation supplies and water allowance needs adjustments to avoid over irrigation and in-efficient use of water.     

Short term effects of saline irrigation on evapotranspiration from lysimeter-grown citrus trees

Eight-year-old Murcott orange trees grown in greenhouse lysimeters filled with sandy soil were subjected to irrigation with saline water to investigate the influence of salinity on daily evapotranspiration (ET). The study was conducted in Japan from 1 August to 15 September 2000. The study duration was divided into three periods of about 2 weeks each. In period I, all lysimeters planted with a tree were irrigated with 60 mm of non-saline water at the water content of 70% of field capacity (FC). Salinity treatments for period II started on 14 August. The treatments during period II were as follows: Lysimeter 1 (L1) had 32 mm non-saline water with an electrical conductivity (EC_I) of 1.0 dS/m applied. At the same time Lysimeter 2 (L2) had 32 mm of saline water with an EC_I of 8.6 dS/m applied when the water content decreased to 70% of FC. Lysimeter 3 (L3) had 16 mm saline water (EC_I=8.6 dS/m) applied at 85% of FC. The irrigation amounts during period II were equal to those corresponding to 1.2 times of water required to reach FC. Treatments in period III were the same as in period I.Daily ET was similar for all weighing lysimeters during period I. The average relative ET for L2 and L3 with respect to L1 (L2/L1 and L3/L1) were similar during this period, with a mean value of 0.99. During period II, ET from L1 was consistently higher than that from L2 and L3. In addition, L3 with a higher irrigation frequency because of irrigation at higher soil water content resulted in higher ET than L2. The average relative ET of period II was 0.71 and 0.88 for both L2 and L3. During the last half of period III, reductions occurred in the ET differences between the saline treatments (L2 and L3) and non-saline control (L1).Evaporation rates from soil did not exceed 0.7 mm per day. Transpiration rates from L1, L2 and L3 during period II varied between 6.3 and 3.1 mm per day, 4.5 and 2.2 mm per day, and 5.8 and 3.0 mm per day, respectively. The results reflected a tangible difference of water extraction by roots from individual soil layers. Maximum water uptake by these trees was observed at layer of 30–60 cm. Nevertheless, no clear differences in water extraction pattern between trees were observed.Approximately, 95% of drainage occurred during the first 2 days following irrigation. The electrical conductivity of soil water (EC_S) and the electrical conductivity of drainage water (EC_D) for the saline water treatments (L2 and L3), compared to the control (L1) were significantly different during period II. EC_S values were 2–5 times higher in saline treatments compared to the control treatment. After irrigating trees with saline water, EC_S increased from 5 to 14 and 16 dS/m in L2 and L3, respectively. Similarly, in both saline treatments, EC_D values were greatly increased after irrigation. During period III, EC_D values increased from 5 to 8 dS/m in L2, and from 3 to 11 dS/m in L3. By contrast, EC_S declined from 14 to 5 dS/m in L2, and from 16 to 3 dS/m in L3 over the same period.     

Impact of treated wastewater irrigation on quality attributes and contamination of tomato fruit

A field experiment was conducted in 1999 and 2000 to investigate the effect of different treatments of potable and treated wastewater on the quality of tomato fruit (Lycopersicon esculentum L. Mill) in Jordan. Tomato seedlings (cvs. GS₁₂ and RS₅₈₉₉₅₆) were furrow irrigated with different mixtures of potable and wastewater (1:0, 1:1, 1:3, and 0:1). The BOD, and SS of the treated effluent used were 34 and 35 mg/l, respectively. Irrigation with treated wastewater did not affect fruit pH, increased their size up to 2 cm in diameter, and weight up to 78.7 g. Additionally, a decrease of 1.5% in the SSC, 0.59 kg in firmness, and 5.1% in weight loss of tomato fruit were recorded. The 0:1 application of treated wastewater resulted in an increased microbial contamination (TC 1.56×10⁴ and 4.7×10² CFU/100 g; FC 3×10² and 130 CFU/100 g; TBC 188×10² and 205×10² CFU/100 g) on the surface of the fruit (skin) for GS₁₂ and RS₅₉₉₉₅₆ varieties, respectively. There was a negligible contamination on fruit scar, and nil in fruit flesh. Contamination increased exponentially with increasing the proportions of treated wastewater application. Since treated wastewater was highly contaminated with total coliform (up to 42.0 CFU/100 ml) and total bacterial count (up to 7.820 CFU/100 ml), hence, contamination was aggravated with increasing the percentage of treated wastewater. It is suggested that the treated wastewater can be used as an alternative for irrigation of tomatoes eaten after cooking, but not for those taken as raw provided that the effluent quality is continuously monitored to avoid contamination.     

The effects of different irrigation regimes on cucumber (Cucumbis sativus L.) yield and yield characteristics under open field conditions

A study was conducted to determine the effects of different drip irrigation regimes on yield and yield components of cucumber (Cucumbis sativus L.) and to determine a threshold value for crop water stress index (CWSI) based on irrigation programming. Four different irrigation treatments as 50 (T-50), 75 (T-75), 100 (T-100) and 125% (T-125) of irrigation water applied/cumulative pan evaporation (IW/CPE) ratio with 3-day-period were studied.Seasonal crop evapotranspiration (ET_c) values were 633, 740, 815 and 903 mm in the 1st year and were 679, 777, 875 and 990 mm in the 2nd year for T-50, T-75, T-100 and T-125, respectively. Seasonal irrigation water amounts were 542, 677, 813 and 949 mm in 2002 and 576, 725, 875 and 1025 mm in 2003, respectively. Maximum marketable fruit yield was from T-100 treatment with 76.65 t ha⁻¹ in 2002 and 68.13 t ha⁻¹ in 2003. Fruit yield was reduced significantly, as irrigation rate was decreased. The water use efficiency (WUE) ranged from 7.37 to 9.40 kg m⁻³ and 6.32 to 7.79 kg m⁻³ in 2002 and 2003, respectively, while irrigation water use efficiencies (IWUE) were between 7.02 and 9.93 kg m⁻³ in 2002 and between 6.11 and 8.82 kg m⁻³ in 2003.When the irrigation rate was decreased, crop transpiration rate decreased as well resulting in increased crop canopy temperatures and CWSI values and resulted in reduced yield. The results indicated that a seasonal mean CWSI value of 0.20 would result in decreased yield. Therefore, a CWSI = 0.20 could be taken as a threshold value to start irrigation for cucumber grown in open field under semi-arid conditions.Results of this study demonstrate that 1.00 IW/CPE water applications by a drip system in a 3-day irrigation frequency would be optimal for growth in semiarid regions.