Latent heat flux over a furrow-irrigated tomato crop using Penman–Monteith equation with a variable surface canopy resistance

The Penman–Monteith (P–M) model with a variable surface canopy resistance (r_c) was evaluated to estimate latent heat flux (LE) or crop evapotranspiration (ET) over a furrow-irrigated tomato crop under different soil water status and atmospheric conditions. The hourly values of r_c were computed as a function of environmental variables (air temperature, vapor pressure deficit, net radiation, and soil heat flux) and a normalized soil water factor (F), which varies between 0 (wilting point, θ_WP) and 1 (field capacity, θ_FC). The Food and Agricultural Organization (FAO-56) method was also evaluated to calculate daily ET based on the reference evapotranspiration, crop coefficient and water stress coefficient. The performance of the P–M model and FAO-56 method were evaluated using LE values obtained from the Bowen ratio system. On a 20 min time interval, the P–M model estimated daytime variation of LE with a standard error of the estimate (SEE) of 46 Wm⁻² and an absolute relative error (ARE) of 3.6%. Thus, daily performance of the P–M model was good under soil water content ranging from 118 to 83 mm (θ_FC and θ_WP being 125 and 69 mm, respectively) and LAI ranging from 1.3 to 3.0. For this validation period, the calculated values of r_c and F ranged between 20 and 114 s m⁻¹ and between 0.87 and 0.25, respectively. In this case, the P–M model was able to predict daily ET with a SEE of 0.44 mm h⁻¹ (1.1 MJ m⁻² d⁻¹) and an ARE of 3.9%. Furthermore, the FAO-PM model computed daily ET with SEE and ARE values of 1.1 mm h⁻¹ (2.8 MJ m⁻² d⁻¹) and 5.2%, respectively.     

Review of measured crop water productivity values for irrigated wheat,rice, cotton and maize

The great challenge of the agricultural sector is to produce more food from less water, which can be achieved by increasing Crop Water Productivity (CWP). Based on a review of 84 literature sources with results of experiments not older than 25 years, it was found that the ranges of CWP of wheat, rice, cotton and maize exceed in all cases those reported by FAO earlier. Globally measured average CWP values per unit water depletion are 1.09, 1.09, 0.65, 0.23 and 1.80 kg m⁻³ for wheat, rice, cotton_seed, cotton_lint and maize, respectively. The range of CWP is very large (wheat, 0.6–1.7 kg m⁻³; rice, 0.6–1.6 kg m⁻³; cotton_seed, 0.41–0.95 kg m⁻³; cotton_lint, 0.14–0.33 kg m⁻³ and maize, 1.1–2.7 kg m⁻³) and thus offers tremendous opportunities for maintaining or increasing agricultural production with 20–40% less water resources. The variability of CWP can be ascribed to: (i) climate; (ii) irrigation water management and (iii) soil (nutrient) management, among others. The vapour pressure deficit is inversely related to CWP. Vapour pressure deficit decreases with latitude, and thus favourable areas for water wise irrigated agriculture are located at the higher latitudes. The most outstanding conclusion is that CWP can be increased significantly if irrigation is reduced and crop water deficit is intendently induced.     

Effects of timing and duration of brackish irrigation water on fruit yield and quality of late summer melons

Brackish water (7 dS m⁻¹) is frequently utilized to drip-irrigate crops in the Negev desert of Israel, the practice being to use deep sandy soils (96% sand) to avoid soil salinization. When muskmelon (Cucumis melo L.), a moderately salt-sensitive crop species, was grown using brackish irrigation under these conditions, yields declined due to a significant reduction in fruit size, but fruit quality parameters improved markedly. In the present study, we tested the hypothesis that the use of fresh irrigation water during the early vegetative phase would increase canopy size and leaf area index (LAI) and hence the potential productivity of the melon plant. The application of brackish water during the reproductive phase, on the other hand, would improve fruit quality. Using multiple irrigations within a 24-h period, applied with drip irrigation, we examined the timing, the duration, and the concentration of brackish irrigation water as tools to optimize fruit yield and quality in late-summer melons. Indeed, the combination of fresh (1.2 dS m⁻¹) and brackish (7 dS m⁻¹) irrigation water increased the yield level to that of fresh water plants whereas it brought about the improvement of fruit quality typical to brackish water plants, thus providing an attractive approach to optimize late-summer melon production. Our results demonstrate the trade-off between fruit size and fruit quality as related to the timing and the duration of brackish irrigation water. The use of a milder (<4.5 dS m⁻¹) salinity level of irrigation water from plant emergence until harvest may be considered as well.     

Phenology based irrigation scheduling and determination of crop coefficient of winter maize in rice fallow of eastern India

Vast rainfed rice area (12 million ha) of eastern India remains fallow after rainy season rice due to lack of appropriate water and crop management strategies inspite of having favourable natural resources, human labourers and good market prospects. In this study, a short duration crop, maize, was tried as test crop with different levels of irrigation during winter season after rainy season rice to increase productivity and cropping intensity of rainfed rice area of the region. Maize hybrid of 120 days duration was grown with phenology based irrigation scheduling viz., one irrigation at early vegetative stage, one irrigation at tassel initiation, two irrigation at tassel initiation + grain filling, three irrigation at early vegetative + tassel initiation + grain filling and four irrigation at early vegetative + tassel initiation + silking + grain-filling stages. Study revealed that one irrigation at tassel initiation stage was more beneficial than that of at early vegetative stage. Upto three irrigation, water use efficiency (WUE) was increased linearly with increased number of irrigation. With four irrigations, the yield was higher, but WUE was lower than that of three irrigations, which might be due to increased water application resulted in increase crop water use without a corresponding increase of yield for the crop with four irrigations. The crop coefficients (K_c) at different stages of the crop were derived after computing actual water use using field water balance approach. The crop coefficients of 0.42–0.47, 0.90–0.97, 1.25–1.33, and 0.58–0.61 were derived at initial, development, mid and late season, respectively with three to four irrigation. Study showed that leaf area index (LAI) was significantly correlated with K_c values with the R² values of 0.93. When LAI exceeded 3.0, the K_c value was 1. Study revealed that the K_c values for the development and mid season stage were slightly higher to that obtained by the procedure proposed by FAO, which might be due to local advection.     

The effects of different irrigation regimes on cucumber (Cucumbis sativus L.) yield and yield characteristics under open field conditions

A study was conducted to determine the effects of different drip irrigation regimes on yield and yield components of cucumber (Cucumbis sativus L.) and to determine a threshold value for crop water stress index (CWSI) based on irrigation programming. Four different irrigation treatments as 50 (T-50), 75 (T-75), 100 (T-100) and 125% (T-125) of irrigation water applied/cumulative pan evaporation (IW/CPE) ratio with 3-day-period were studied.Seasonal crop evapotranspiration (ET_c) values were 633, 740, 815 and 903 mm in the 1st year and were 679, 777, 875 and 990 mm in the 2nd year for T-50, T-75, T-100 and T-125, respectively. Seasonal irrigation water amounts were 542, 677, 813 and 949 mm in 2002 and 576, 725, 875 and 1025 mm in 2003, respectively. Maximum marketable fruit yield was from T-100 treatment with 76.65 t ha⁻¹ in 2002 and 68.13 t ha⁻¹ in 2003. Fruit yield was reduced significantly, as irrigation rate was decreased. The water use efficiency (WUE) ranged from 7.37 to 9.40 kg m⁻³ and 6.32 to 7.79 kg m⁻³ in 2002 and 2003, respectively, while irrigation water use efficiencies (IWUE) were between 7.02 and 9.93 kg m⁻³ in 2002 and between 6.11 and 8.82 kg m⁻³ in 2003.When the irrigation rate was decreased, crop transpiration rate decreased as well resulting in increased crop canopy temperatures and CWSI values and resulted in reduced yield. The results indicated that a seasonal mean CWSI value of 0.20 would result in decreased yield. Therefore, a CWSI = 0.20 could be taken as a threshold value to start irrigation for cucumber grown in open field under semi-arid conditions.Results of this study demonstrate that 1.00 IW/CPE water applications by a drip system in a 3-day irrigation frequency would be optimal for growth in semiarid regions.     

Monitoring wheat phenology and irrigation in Central Morocco: On the use of relationships between evapotranspiration,crops coefficients,leaf area index and remotely-sensed vegetation indices

The monitoring of crop production and irrigation at a regional scale can be based on the use of ecosystem process models and remote sensing data. The former simulate the time courses of the main biophysical variables which affect crop photosynthesis and water consumption at a fine time step (hourly or daily); the latter allows to provide the spatial distribution of these variables over a region of interest at a time span from 10 days to a month. In this context, this study investigates the feasibility of using the normalised difference vegetation index (NDVI) derived from remote sensing data to provide indirect estimates of: (1) the leaf area index (LAI), which is a key-variable of many crop process models; and (2) crop coefficients, which represent the ratio of actual (AET) to reference (ET₀) evapotranspiration.A first analysis is performed based on a dataset collected at field in an irrigated area of the Haouz plain (region of Marrakesh, Central Morocco) during the 2002–2003 agricultural season. The seasonal courses of NDVI, LAI, AET and ET₀ have been compared, then crop coefficients have been calculated using a method that allows roughly to separate soil evaporation from plant transpiration. This allows to compute the crop basal coefficient (K_cb) restricted to the plant transpiration process. Finally, three relationships have been established. The relationships between LAI and NDVI as well as between LAI and K_cb were found both exponential, with associated errors of 30% and 15%, respectively. Because the NDVI saturates at high LAI values (>4), the use of remotely-sensed data results in poor accuracy of LAI estimates for well-developed canopies. However, this inaccuracy was not found critical for transpiration estimates since AET appears limited to ET₀ for well-developed canopies. As a consequence, the relationship between NDVI and K_cb was found linear and of good accuracy (15%).Based on these relationships, maps of LAI and transpiration requirements have been derived from two Landsat7-ETM+ images acquired at the beginning and the middle of the agricultural season. These maps show the space and time variability in crop development and water requirements over a 3 km × 3 km irrigated area that surrounds the fields of study. They may give an indication on how the water should be distributed over the area of interest in order to improve the efficiency of irrigation. The availability, in the near future, of Earth Observation Systems designed to provide both high spatial resolution (10 m) and frequent revisit (day) would make it feasible to set up such approaches for the operational monitoring of crop phenology and irrigation at a regional scale.     

Estimation of evapotranspiration,transpiration ratio and water-use efficiency from a sparse canopy using a compartment model

Using the Shuttleworth and Wallace (S–W) model, evapotranspiration (ET); transpiration ratio (T/ET), which is the ratio of transpiration (T) to ET; and water-use efficiency (WUE) were estimated for a sparsely planted sorghum canopy that was well irrigated. That model is designed to estimate separately the evaporation from soil and transpiration from crops.The evapotranspiration estimates for both short- and long-term measurement periods coincided closely with the Bowen ratio energy balance (BREB) measurements. The transpiration ratios were affected by the canopy resistances and the soil surface resistances during the day. The regression curve between leaf area index (LAI) and transpiration ratio suggests that LAI, less than 1.6, determined the transpiration ratio in the absence of water stresses by soil water drought and extreme weather condition. The WUEs for transpiration (WUEt) and evapotranspiration (WUEet), which are the total dry matter (TDM) production for 1 kg T and ET, reached the peaks of 9.0 and 4.5 g kg⁻¹ H₂O, respectively, in the end of July when the total dry matter increasing rate was greatest. These two WUEs degraded to less than zero in the end of August when the plant biomass decreased due to drying and death. The WUEs are largely affected by the TDM seasonal increment rate.Thus, in a sparse crop, the crop growth properties (i.e. LAI and TDM increment) mainly determine the crop water uses (i.e. the transpiration ratio and water-use efficiency) in the absence of water stresses.     

An ecological optimality approach for predicting deep drainage from tree belts of alley farms in water-limited environments

The clearing of natural vegetation for agriculture in southern Australia has increased deep drainage, led to increased groundwater recharge and, hence, the salinisation of land and streams. Alley farming systems, comprising alternate belts of trees and crops, have been proposed for reducing deep drainage but their effectiveness is unknown. This paper describes an application of ecological optimality theory to estimate the equivalent no drainage (ENOD) width B (m) for a tree belt. The relative drainage RD from an alley farm, compared to conventional agriculture is, therefore, 1 − B/W, where W is the centre spacing of the belts. We present a method for estimating B_LA from the leaf area per unit length of belt LLA (m² m⁻¹), divided by the leaf area index LAI (m² m⁻²) of nearby natural vegetation. Preliminary evaluation of B_LA showed good agreement with B_WB measured from water balance and B_DD measured from deep drainage. The estimation of B_LA for calculation of RD allows rapid estimates of the relative drainage reduction expected from alley farms in water-limited environments.     

A simulation study of chickpea crop response to limited irrigation in a semiarid environment

In West Asia and North Africa (WANA) including northwest (NW) Iran irrigation is becoming increasingly available and investigation of the effect of limited irrigation (LI) is a research need. Only a few seasons of successful experimentation exist with LI effects. Thus, the objective of this simulation study was to examine potential long-term benefits of limited irrigation in NW Iran in terms of grain yield. To do this, a simple, mechanistic chickpea (Cicer arietinum L.) model and 16 years of weather data of Maragheh (NW Iran) were used. Three LI systems with one, two and three irrigations and each with three plant population densities (25, 38 and 50 plants m⁻²) were simulated. Results showed chickpea crop experiences terminal drought stress that is started at a time between flowering and beginning seed growth (BSG). This terminal drought stress severely reduces grain yield by 67%, from 2766 kg ha⁻¹ under full-irrigated conditions to 909 kg ha⁻¹ under rainfed conditions. Grain yield was significantly increased with LI compared to rainfed conditions. Grain yields were reached to 60, 75 and 90% of grain yield simulated under full-irrigated (generally requires five irrigations) conditions. In LI with one irrigation its application at BSG, and in LI with two and three irrigations, application of first irrigation at flowering and application of one or two other irrigations when fraction of transpirable soil water dropped to 0.5 in the root zone resulted in higher grain yield. Water use efficiency was, also, increased with LI by 28, 39 and 52% for one, two and three irrigations, respectively. In LI systems with two and three irrigations it was required to a higher plant density (38 or 50 plants m⁻²) to capture and to use applied water more efficiently.     

Trickle and sprinkler irrigation of potato (Solanum tuberosum L.) in the Middle Anatolian Region in Turkey

The potato (Solanum tuberosum L.) is widely planted in the Middle Anatolian Region, especially in the Nigde-Nevsehir district where 25% of the total potato growing area is located and produces 44% of the total yield. In recent years, the farmers in the Nigde-Nevsehir district have been applying high amounts of nitrogen (N) fertilizers (sometimes more than 900 kg N ha⁻¹) and frequent irrigation at high rates in order to get a much higher yield. This situation results in increased irrigation and fertilization costs as well as polluted ground water resources and soil. Thus, it is critical to know the water and nitrogen requirements of the crop, as well as how to improve irrigation efficiency. Field experiments were conducted in the Nigde-Nevsehir (arid) region on a Fluvents (Entisols) soil to determine water and nitrogen requirements of potato crops under sprinkler and trickle irrigation methods. Irrigation treatments were based on Class A pan evaporation and nitrogen levels were formed with different nitrogen concentrations.The highest yield, averaging 47,505 kg ha⁻¹, was measured in sprinkler-irrigated plots at the 60 g m⁻³ nitrogen concentration level in the irrigation treatment with limited irrigation (480 mm). Statistically higher tuber yields were obtained at the 45 and 60 g m⁻³ nitrogen concentration levels in irrigation treatments with full and limited irrigation. Maximum yields were obtained with about 17% less water in the sprinkler method as compared to the trickle method (not statistically significant). On the loam and sandy loam soils, tuber yields were reduced by deficit irrigation corresponding to 70% and 74% of evapotranspiration in sprinkler and trickle irrigations, respectively. Water use of the potato crop ranged from 490 to 760 mm for sprinkler-irrigated plots and 565–830 mm for trickle-irrigated treatments. The highest water use efficiency (WUE) levels of 7.37 and 4.79 kg m⁻³ were obtained in sprinkle and trickle irrigated plots, respectively. There were inverse effects of irrigation and nitrogen levels on the WUE of the potato crops. Significant linear relationships were found between tuber yield and water use for both irrigation methods. Yield response factors were calculated at 1.05 for sprinkler methods and 0.68 for trickle methods. There were statistically significant linear and polynomial relationships between tuber yield and nitrogen amounts used in trickle and sprinkler-irrigated treatments, respectively. In sprinkler-irrigated treatments, the maximum tuber yield was obtained with 199 kg N ha⁻¹. The tuber cumulative nitrogen use efficiency (NUE_cu) and incremental nitrogen use efficiency (NUE_in) were affected quite differently by water, nitrogen levels and years. NUE_cu varied from 16 to 472 g kg⁻¹ and NUE_in varied from 75 to 1035 g kg⁻¹ depending on the irrigation method. In both years, the NH₄-N concentrations were lower than NO₃-N, and thus the removed nitrogen and nitrogen losses were found to be 19–87 kg ha⁻¹ for sprinkler methods and 25–89 kg ha⁻¹ for trickle methods. Nitrogen losses in sprinkler methods reached 76%, which were higher than losses in trickle methods.     

Water use and lint yield response of drip irrigated cotton to the length of irrigation season

A 2-year experiment was conducted at Tal Amara Research Station in the Bekaa Valley of Lebanon to determine water use and lint yield response to the length of irrigation season of drip irrigated cotton (Gossypium hirsutum L.). Crop evapotranspiration (ET_crop) and reference evapotranspiration (ET_rye-grass) were directly measured at weekly basis during the 2001 growing period using crop and rye-grass drainage lysimeters. Crop coefficients (K_c) in the different growth stages were calculated as ET_crop/ET_rye-grass. Then, the calculated K_c values were used in the 2002 growing period to estimate evapotranspiration of cotton using the FAO method by multiplying the calculated K_c values by ET_rye-grass measured in 2002. The length of irrigation season was determined by terminating irrigation permanently at first open boll (S1), at early boll loading (S2), and at mid boll loading (S3). The three treatments were compared to a well-watered control (C) throughout the growing period. Lint yield was defined as a function of components including plant height at harvest, number of bolls per plant, and percentage of opened bolls per plant.Lysimeter-measured crop evapotranspiration (ET_crop) totaled 642 mm in 2001 for a total growing period of 134 days, while when estimated with the FAO method in 2002 it averaged 669 mm for a total growing period of 141 days from sowing to mature bolls. Average K_c values varied from 0.58 at initial growth stages (sowing to squaring), to 1.10 at mid growth stages (first bloom to first open boll), and 0.83 at late growth stages (early boll loading to mature bolls).Results showed that cotton lint yields were reduced as irrigation amounts increased. Average across years, the S1 treatment produced the highest yield of 639 kg ha⁻¹ from total irrigations of 549 mm, compared to the S2 and S3 treatments, which yielded 577 and 547 kg ha⁻¹ from total irrigations of 633 and 692 mm, respectively, while the control resulted in 457 kg ha⁻¹ of lint yield from 738 mm of irrigation water. Water use efficiency (WUE) was found to be higher in S1 treatment and averaged 1.3 kg ha⁻¹ mm⁻¹, followed by S2 (1.1 kg ha⁻¹ mm⁻¹), and S3 (1.0 kg ha⁻¹ mm⁻¹), while in the control WUE was 0.80 kg ha⁻¹ mm⁻¹. Lint yield was negatively correlated with plant height and the number of bolls per plant and positively correlated with the percentage of opened bolls. This study suggests that terminating irrigation at first open boll stage has been found to provide the highest cotton yield with maximum WUE under the semi-arid conditions of the Bekaa Valley of Lebanon.     

Water productivity analysis of irrigated crops in Sirsa district,India

Water productivity (WP) expresses the value or benefit derived from the use of water, and includes essential aspects of water management such as production for arid and semi-arid regions. A profound WP analysis was carried out at five selected farmer fields (two for wheat–rice and three for wheat–cotton) in Sirsa district, India during the agricultural year 2001–02. The ecohydrological soil–water–atmosphere–plant (SWAP) model, including detailed crop simulations in combination with field observations, was used to determine the required hydrological variables such as transpiration, evapotranspiration and percolation, and biophysical variables such as dry matter or grain yields. The use of observed soil moisture and salinity profiles was found successful to determine indirectly the soil hydraulic parameters through inverse modelling.Considerable spatial variation in WP values was observed not only for different crops but also for the same crop. For instance, the WP_ET, expressed in terms of crop grain (or seed) yield per unit amount of evapotranspiration, varied from 1.22 to 1.56 kg m⁻³ for wheat among different farmer fields. The corresponding value for cotton varied from 0.09 to 0.31 kg m⁻³. This indicates a considerable variation and scope for improvements in water productivity. The average WP_ET (kg m⁻³) was 1.39 for wheat, 0.94 for rice and 0.23 for cotton, and corresponds to average values for the climatic and growing conditions in Northwest India. Including percolation in the analysis, i.e. crop grain (or seed) yield per unit amount of evapotranspiration plus percolation, resulted in average WP_ETQ (kg m⁻³) values of 1.04 for wheat, 0.84 for rice and 0.21 for cotton. Factors responsible for low WP include the relative high amount of evaporation into evapotranspiration especially for rice, and percolation from field irrigations. Improving agronomic practices such as aerobic rice cultivation and soil mulching will reduce this non-beneficial loss of water through evaporation, and subsequently will improve the WP_ET at field scale. For wheat, the simulated water and salt limited yields were 20–60% higher than measured yields, and suggest substantial nutrition, pest, disease and/or weed stresses. Improved crop management in terms of timely sowing, optimum nutrient supply, and better pest, disease and weed control for wheat will multiply its WP_ET by a factor of 1.5! Moreover, severe water stress was observed on cotton (relative transpiration < 0.65) during the kharif (summer) season, which resulted in 1.4–3.3 times lower water and salt limited yields compared with simulated potential yields. Benefits in terms of increased cotton yields and improved water productivity will be gained by ensuring irrigation supply at cotton fields, especially during the dry years.     

Role of straw mulching in non-continuously flooded rice cultivation

Rice (Oryza sativa L.) cultivation under non-flooded (NF) condition is a new alternative to the conventional flooded (CF) rice cultivation system in the regions where rainfall and fresh water resources are limited. Non-flooded rice cultivation may mediate rice growth performance and mulching may be good practice to reduce evapotranspiration and increase water use efficiency (WUE). The research objectives of this study were to investigate the effects of non-flooded cultivation with straw mulching on the rice agronomic traits and water use efficiency of the second rice cropping season (late rice). The treatments were conventional flooded rice cultivation, non-flooded rice cultivations without (NF-ZM) and with rice straw mulching (NF-SM). Irrigation water was 19950 m³ ha⁻¹ in 2003 and 15,850 m³ ha⁻¹ in 2004 in the CF treatments and 7200 m³ ha⁻¹ in 2003 and 5045 m³ ha⁻¹ in 2004 in the non-flooded rice fields (NF-ZM and NF-SM treatments).The field measurements showed that water seepage was 13,442 m³ ha⁻¹ in the CF treatment, 5510 m³ ha⁻¹ in the NF-ZM treatment and 5424 m³ ha⁻¹ in the NF-SM treatment. Rice straw mulching decreased evapotranspiration by 33% and 63% (in 2003), 36.5% and 57.1% (in 2004) to the NF-ZM treatment and CF treatment, respectively. Compared with the NF-ZM treatment, mulch application significantly increased the leaf area per plant, main root length, tap root length and root dry weight per plant of crop. The yield of the NF-SM treatment (2003: 6489 kg/hm²; 2004: 8574.8 kg/hm²) was similar with the value of the CF treatment (2003: 6811.5; 2004: 8630.5 kg/hm²), and much higher than the NF-ZM treatment (2003: 4716; 2004: 6394.8 kg/hm²). The order of irrigation water use efficiency (IWUE) and water use efficiency were as follows: NF-SM > NF-ZM > CF.     

Response of safflower (Carthamus tinctorius L.) to saline soils and irrigation: I. Consumptive water use

Salt-tolerant crops can be grown with saline water from tile drains and shallow wells as a practical strategy to manage salts and sustain agricultural production in the San Joaquin Valley (SJV) of California. Safflower (Carthamus tinctorius L.) was grown in previously salinized plots that varied in average electrical conductivity (EC_e) from 1.8 to 7.2 dS m⁻¹ (0–2.7 m depth) and irrigated with either high quality (EC_i<1 dS m⁻¹) or saline (EC_i=6.7 dS m⁻¹) water. One response of safflower to increasing root zone salinity was decreased water use and root growth. Plants in less saline plots recovered more water on average (515 mm) and at a greater depth than in more salinized plots (435 mm). With greater effective salinity, drainage increased with equivalent water application rates. Seed yield was not correlated with consumptive water use over the range of 400–580 mm. Total biomass and plant height at harvest were proportional to water use over the same range. Safflower tolerated greater levels of salinity than previously reported. Low temperatures and higher than average relative humidity in spring likely moderated the water use of safflower grown under saline conditions.     

Growth response of four turfgrass species to salinity

The need for salinity tolerant turfgrasses is increasing because of the increased use of effluent or other low quality waters for turfgrass irrigation. Greenhouse container and hydroponic experiments were conducted to determine the relative salinity tolerance and growth responses of ‘Challenger’ Kentucky bluegrass (Poa pratensis L.) (KBG), ‘Arid’ tall fescue (Festuca arundinacea Schreb) (TF), ‘Fults’ alkaligrass (Puccinellia distans (L.) Parl.) (AG), and a saltgrass (Distichlis spicata (Torr.) Beetle) collection (SG). In the container experiments, irrigation waters of different salinity levels were applied to experimental plants grown in plastic pots filled with a mix of sand and Isolite. The results indicated that KBG, TF, AG, and SG experienced a 50% shoot growth reduction at 4.9, 10.0, 20.0, and 34.9 dS m⁻¹, respectively, and a 50% root growth reduction at 5.8, 19.6, 24.9 and 41.0 dS m⁻¹, respectively. In the hydroponic experiment, grasses were grown in saline solution at 2.0, 4.7, 9.4, 14.1, 18.8, and 23.5 dS m⁻¹. Kentucky bluegrass, TF, AG, and SG experienced a 50% shoot growth reduction at 5.5, 14.2, 23.0, and 34.5 dS m⁻¹, respectively, and a 50% root growth reduction at 7.9, 21.5, 30.4 and 40.8 dS m⁻¹, respectively. Root to shoot ratio of KBG remained constant, whereas those of TF, AG, and SG increased at all salinity levels. Salinity caused root cortex cells to collapse, in KBG at 14.1 dS m⁻¹ and in TF at 23.5 dS m⁻¹. Alkaligrass and SG only had a few cell collapses even at 23.5 dS m⁻¹. Bi-cellular salt glands were observed only on leaves of SG. The ranking for salinity tolerance of selected grasses was: SG>AG>TF>KBG. Salt glands present in SG, root growth stimulation of SG and AG, and maintenance of relatively high root to shoot ratio in TF are apparent adaptive mechanisms exhibited by these grasses for salinity tolerance.     

Irrigation management and hydrosalinity balance in a semi-arid area of the middle Ebro river basin (Spain)

The analysis of irrigation and drainage management and their effects on the loading of salts is important for the control of on-site and off-site salinity effects of irrigated agriculture in semi-arid areas. We evaluated the irrigation management and performed the hydrosalinity balance in the D-XI hydrological basin of the Monegros II system (Aragón, Spain) by measuring or estimating the volume, salt concentration and salt mass in the water inputs (irrigation, precipitation and Canal seepage) and outputs (evapotranspiration and drainage) during the period June 1997–September 1998. This area is irrigated by solid-set sprinklers and center pivots, and corn and alfalfa account for 90% of the 470 ha irrigated land. The soils are low in salts (only 10% of the irrigated land is salt-affected), but shallow (<2 m) and impervious lutites high in salts (average EC_e=10.8 dS m⁻¹) and sodium (average SAR_e=20 (meq l⁻¹)^0.5) are present in about 30% of the study area.The global irrigation efficiency was high (Seasonal Irrigation Performance Index=92%), although the precipitation events were not sufficiently incorporated in the scheduling of irrigation and the low irrigation efficiencies (60%) obtained at the beginning of the irrigated season could be improved by minimising the large post-planting irrigation depths given to corn to promote its emergence. The salinity of the irrigation water was low (EC=0.36 dS m⁻¹), but the drainage waters were saline (EC=7.5 dS m⁻¹) and sodic (SAR=10.3 (meq l⁻¹)^0.5) (average values for the 1998 hydrological year) due to the dissolution and transport of the salts present in the lutites. The discharge salt loading was linearly correlated (P<0.001) with the volume of drainage. The slope of the daily mass of salts in the drainage waters versus the daily volume of drainage increased at a rate 25% higher in 1997 (7.6 kg m⁻³) than in 1998 (6.1 kg m⁻³) due to the higher precipitation in 1997 and the subsequent rising of the saline watertables in equilibrium with the saline lutites. Drainage volumes depended (P<0.001) on irrigation volumes and were very low (194 mm for the 1998 hydrological year), whereas the salt loading was moderate (13.5 Mg ha⁻¹ for the 1998 hydrological year) taking into account the vast amount of salts stored within the lutites. We concluded that the efficient irrigation and the low salinity of the irrigation water in the study area allowed for a reasonable control of the salt loading conveyed by the irrigation return flows without compromising the salinization of the soil’s root-zone.     

Effects of winter crop and supplemental irrigation on crop yield,water use efficiency and profitability in rainfed rice based cropping system of eastern India

Soil moisture availability is the main limiting factor for growing second crops in rainfed rice fallows of eastern India. Only rainfed rice is grown with traditional practices during the rainy season (June–October) with large areas (13 m ha⁻¹) remaining fallow during the subsequent dry season (November–March) inspite of annual rainfall of the order 1000–2000 mm. In this study an attempt was made to improve productivity of rainfed rice during rainy season and to grow second crops in rice fallow during dry (winter) season with supplemental irrigation from harvested rainwater. Rice was grown as first crop with improved as well as traditional farmers’ management practices to compare the productivity between these two treatments. Study revealed that 87.1–95.6% higher yield of rice was obtained with improved management over farmers’ practices. Five crops viz., maize, groundnut, sunflower, wheat and potato were grown in rice fallow during dry (winter) season with two, three and four supplemental irrigations and improved management. Sufficient amount of excess rainwater (runoff) was available (381 mm at 75% probability level) to store and recycle for supplementary irrigation to second crops grown after rice. Study revealed that supplemental irrigation had significant effect (P < 0.001) on grain yield of dry season crops and with two irrigation mean yields of 1845, 785, 905, 1420, 8050 kg ha⁻¹ were obtained with maize (grain), groundnut, sunflower, wheat and potato (tuber), respectively. With four irrigations 214, 89, 78, 81, 54% yield was enhanced over two irrigations in respective five crops. Water use efficiency (WUE) of 13.8, 3.35, 3.39, 5.85 and 28.7 kg ha⁻¹ was obtained in maize, groundnut, sunflower, wheat, potato (tuber), respectively with four irrigations. The different plant growth parameters like maximum above ground biomass, leaf area index and root length were also recorded with different levels of supplemental irrigation. The study amply revealed that there was scope to improve productivity of rainfed rice during rainy season and to grow another profitable crops during winter/dry season in rice fallow with supplemental irrigation from harvested rainwater of rainy season.     

Water quality assessment of different reservoir types in relation to nutrient solution use in hydroponics

Hydroponics requires good quality water. For this purpose, water quality is based on concentrations of specific ions and phytotoxic substances as well as the presence of organisms and substances that can clog irrigation systems. Here, four irrigation reservoirs, i.e. two rainwater ponds, a peat ditch, and a natural lake, were analyzed to determine whether or not they conform to water quality guidelines. Based on our data, the four reservoirs could be divided into two categories in respect to their water quality. The two rainwater ponds belong to the category characterized by low input of ionic strength (480 μmol m⁻¹), low concentration of unwanted ions, such as SO₄²⁻ (63 μmol l⁻¹) and Zn²⁺ (3.9 μmol l⁻¹), a moderate bacterial population (lg 4.9 CFU m⁻¹), and moderate algae density (lg 6.0 cells ml⁻¹). The rainwater ponds were found to contain a good diversity in bacteria (45 species from 25 genera), and a poor diversity of algae (15 species from 4 groups). The other category, to which the peat ditch and natural lake belong, is characterized by a high ionic strength (12,200 μmol l⁻¹), high concentrations of alkali ions (Mg²⁺: 890 μmol l⁻¹; Ca²⁺: 3.260 μmol l⁻¹; K⁺: 470 μmol l⁻¹), a moderate bacterial (lg 4.7 CFU ml⁻¹), but low algae density (lg 5.0 cells ml⁻¹). In comparison to the first category, the diversity of the bacteria was poor (seven species from three genera). However, in sharp contrast was the rich algal community detected in the peat ditch, for which 32 species from six groups were found, whereas in the natural lake, only one group with seven species was identified. In all reservoirs, species of the genera Paenibacillus and Bacillus were detected, and small green algae, e.g. Scenedesmus spp., also dominated in each case. Overall, the bacterial and algal densities showed wide fluctuations between water sources, and neither caused filter clogging as observed in investigations of others. The quality of the rainwater investigated was assessed to be well suited for use in hydroponics due to appropriate nutrient concentration (except Zn²⁺ in one pond), and lack of potential bacterial and algal development. However, we recommend water from the natural lake and the peat ditch to be used with care because of the high nutrient concentration.     

Evapotranspiration and seed yield of field grown soybean under deficit irrigation conditions

Evapotranspiration was measured for a reference crop, rye grass (Lolium prerenne) and soybean (Glycine max L. Merril) grown over two seasons in 2000 and 2001 at Tal Amara Research Station, Lebanon, using drainage and weighing lysimeters. Climatic data from the field weather station were recorded daily. Within the experimental plots, irrigation was withheld at full bloom, R2 stage (S1 treatment), at seed enlargement, R5 stage (S2 treatment) and at mature seeds, R7 stage (S3 treatment). Further, a control (C) was fully-irrigated throughout the growing period.Average crop evapotranspiration (ETc) as measured by the drainage lysimeters in 2000 totaled 800 mm for a total growing period of 140 days. However, when ETc was measured by the weighing lysimeter in 2001, it was 725 mm during a growing period of 138 days. Average crop coefficients (K_c) were computed for different growth stages for the two growing periods by dividing the measured crop evapotranspiration (ETc) by the corresponding measured reference evapotranspiration (ETo-rye grass). K_c values ranged from 0.62 at V10 stage (10th node on the main stem beginning with the unifoliolate node) to 1.0 at pod initiation, then to 0.81 at mature pods.Growth parameters, leaf area index (LAI) and dry matter accumulation, have been shown to be sensitive to water stress caused by the deficit irrigations. However, growth parameters were found to compensate for water stress at early stages, while at seed maturity the compensation ability was decreased.Plants of the lysimeters produced average aboveground biomass and seed yield of 8.1 and 3.5 t ha⁻¹, respectively. However, in the well-irrigated field treatment, aboveground biomass and seed yield averaged 7.3 and 3.2 t ha⁻¹, respectively. Deficit irrigation at R2 stage reduced aboveground biomass and seed yield by 16 and 4%, respectively, while deficit irrigation at R5 stage reduced these two parameters by 6 and 28%, respectively, with comparison to the control. The significant decrease in biomass at R2 stage due to water deficit may be attributed to a pronounced reduction in the number of vegetative nodes. However, limited irrigation at this stage did not reduce significantly (P < 0.01) neither seed number nor seed weight, while at R5 stage these two parameters were reduced by 20 and 10%, respectively, with comparison to the control. Results showed also that deficit irrigation at R7 stage (S3) was more profitable than irrigation deficit at any other crop phenology and did not cause significant reductions either in seed number or seed weight.     

Water requirement of drip irrigated tomatoes grown in greenhouse in tropical environment

Four different levels of drip fertigated irrigation equivalent to 100, 75, 50 and 25% of crop evapotranspiration (ET_c), based on Penman–Monteith (PM) method, were tested for their effect on crop growth, crop yield, and water productivity. Tomato (Lycopersicon esculentum, Troy 489 variety) plants were grown in a poly-net greenhouse. Results were compared with the open cultivation system as a control. Two modes of irrigation application namely continuous and intermittent were used. The distribution uniformity, emitter flow rate and pressure head were used to evaluate the performance of drip irrigation system with emitters of 2, 4, 6, and 8 l/h discharge. The results revealed that the optimum water requirement for the Troy 489 variety of tomato is around 75% of the ET_c. Based on this, the actual irrigation water for tomato crop in tropical greenhouse could be recommended between 4.1 and 5.6 mm day⁻¹ or equivalent to 0.3–0.4 l plant⁻¹ day⁻¹. Statistically, the effect of depth of water application on the crop growth, yield and irrigation water productivity was significant, while the irrigation mode did not show any effect on the crop performance. Drip irrigation at 75% of ET_c provided the maximum crop yields and irrigation water productivity. Based on the observed climatic data inside the greenhouse, the calculated ET_c matched the 75–80% of the ET_c computed with the climatic parameters observed in the open environment. The distribution uniformity dropped from 93.4 to 90.6%. The emitter flow rate was also dropped by about 5–10% over the experimental period. This is due to clogging caused by minerals of fertilizer and algae in the emitters. It was recommended that the cleaning of irrigation equipments (pipe and emitter) should be done at least once during the entire cultivation period.